Compositor control all the input sub-device (VID, GDP)
and the mixer(s).
It is the main entry point for composition.
Layer interface is used to control the abstracted layers.
Add debug in mixer and GDP.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Mixer hardware IP is responsible of mixing the different inputs layers.
Z-order is managed by the mixer.
We could 2 mixers: one for main path and one for auxillary path
Mixers are part of Compositor hardware block
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
VIDeo plug are one of the compositor input sub-devices.
VID are dedicated to video inputs like YUV plans.
Like GDP, VID are part of Compositor hardware block
and use sti_layer structure to provide an abstraction for
Compositor calls.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Generic Display Pipeline are one of the compositor input sub-devices.
GDP are dedicated to graphic input like RGB plans.
GDP is part of Compositor hardware block which will be introduce later.
A sti_layer structure is used to abstract GDP calls from Compositor.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
TVout hardware block is responsible to dispatch the data flow coming
from compositor block to any of the output (HDMI or Analog TV).
It control when output are start/stop and configure according the
require flow path.
TVout is the parent of HDMI and HDA drivers and bind them at runtime.
Tvout is mapped on drm_encoder structure.
One encoder is created for each of the sub-devices and link to their
connector/bridge
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Add driver to support analog TV ouput.
HDA driver is mapped on drm_bridge and drm_connector structures.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
The address prefix 00:90:4C is used by Broadcom in their initial
configuration. When a mac address with the prefix 00:90:4C is used all
devices from the same series are sharing the same mac address. To
prevent mac address collisions we replace them with a mac address based
on the base address. To generate such addresses we take the main mac
address from et0macaddr and increase it by two for the first wifi
device and by 3 for the second one. This matches the printed mac
address on the device. The main mac address increased by one is used as
wan address by the vendor code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: zajec5@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7489/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add driver for HDMI output.
HDMI PHY registers are mixed into HDMI device registers
and their is only one IRQ for all this hardware block.
That is why PHYs aren't using phy framework but only a
thin hdmi_phy_ops structure with start and stop functions.
HDMI driver is mapped on drm_bridge and drm_connector structures.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
The reboot on the BCM47XX SoCs is done, by setting the watchdog counter
to 1 and let it trigger a reboot, when it reaches 0. Some devices with
a BCM4705/BCM4785 SoC do not reboot when the counter is set to 1 and
decreased to 0 by the hardware. It looks like it works more reliable
when we set it to 3. As far as I understand the hardware, this should
not make any difference, but I do not have access to any documentation
for this SoC.
It is still not 100% reliable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: zajec5@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7488/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Video Traffic Advance Communication Rx and Tx drivers are designed
for inter-die communication.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Video Time Generator drivers are used to synchronize the compositor
and tvout hardware IPs by providing line count, sample count,
synchronization signals (HSYNC, VSYNC) and top and bottom fields
indication.
VTG are used by pair for each data path (main or auxiliary)
one for master and one for slave.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
NFNL_MSG_ACCT_GET_CTRZERO modifies dumped flags, in this case
client see unmodified (uncleared) counter value and cleared
overquota state - end user doesn't know anything about overquota state,
unless end user subscribed on overquota report.
Signed-off-by: Alexey Perevalov <a.perevalov@samsung.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add DRM/KMS driver bindings documentation.
Describe the required properties for each of the hardware IPs drivers.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Exynos has buggy firmware that puts bad data into the memory node. Commit
1c2f87c2 (ARM: Get rid of meminfo) exposed the bug by dropping the artificial
upper bound on the number of memory banks that can be added. Exynos fails to
boot after that commit. This branch fixes it by splitting the early DT parse
function and inserting a fixup hook. Exynos uses the hook to correct the DT
before parsing memory regions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lmyQ
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull Exynos platform DT fix from Grant Likely:
"Device tree Exynos bug fix for v3.16-rc7
This bug fix has been brewing for a while. I hate sending it to you
so late, but I only got confirmation that it solves the problem this
past weekend. The diff looks big for a bug fix, but the majority of
it is only executed in the Exynos quirk case. Unfortunately it
required splitting early_init_dt_scan() in two and adding quirk
handling in the middle of it on ARM.
Exynos has buggy firmware that puts bad data into the memory node.
Commit 1c2f87c225 ("ARM: Get rid of meminfo") exposed the bug by
dropping the artificial upper bound on the number of memory banks that
can be added. Exynos fails to boot after that commit. This branch
fixes it by splitting the early DT parse function and inserting a
fixup hook. Exynos uses the hook to correct the DT before parsing
memory regions"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
arm: Add devicetree fixup machine function
of: Add memory limiting function for flattened devicetrees
of: Split early_init_dt_scan into two parts
often during boot with Ubuntu 14.04 PV guests.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJT2PhgAAoJEFxbo/MsZsTRlzIH/1HjbkGZmRlOj5wcrYlWCUJ/
DGLBHc76so52xd9oP8COT5tuSVP6/usPPLFaOmVZ7fMiOpoyz9d3lc0g56otw3gJ
tTUFTyW0EoFtvmIl50OMC726p9azETjA3P2XJkV/D3GhBGGqgrP5uR+mRvisvq3y
eGZEx1UIHv1jov47TBFR1NcckXBWw+6J9m34y9h6an9VNDCuuGwYZ8dfGAFsLrVb
lGLTmgQQmyk4SexVINfOwL40KkVDVEq+X74HcPviyNHEIy66xLzMtKpL+Sf4xeuv
VG3JhqAUGuRGGK48rrbpxhBbpxGp35O9RV68YrGssxfuTejSYduw5zTzzt30QIA=
=cr8X
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.16-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fix from David Vrabel:
"Fix BUG when trying to expand the grant table. This seems to occur
often during boot with Ubuntu 14.04 PV guests"
* tag 'stable/for-linus-3.16-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: safely map and unmap grant frames when in atomic context
on some 64K enabled ARM64 hosts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hoNp
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fix from Paolo Bonzini:
"Fix a bug which allows KVM guests to bring down the entire system on
some 64K enabled ARM64 hosts"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: arm64: vgic: fix hyp panic with 64k pages on juno platform
This reverts commit 20fbe3ae99.
As reported by Stephen Rothwell, it causes compile failures in certain
configurations:
drivers/net/usb/cdc_subset.c:360:15: error: 'dummy_prereset' undeclared here (not in a function)
.pre_reset = dummy_prereset,
^
drivers/net/usb/cdc_subset.c:361:16: error: 'dummy_postreset' undeclared here (not in a function)
.post_reset = dummy_postreset,
^
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: David Miller <davem@davemloft.net>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matching x86 and making it more convenient to run the arm64 default
kernel as distros like Ubuntu need this option.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull networking fixes from David Miller:
1) Make fragmentation IDs less predictable, from Eric Dumazet.
2) TSO tunneling can crash in bnx2x driver, fix from Dmitry Kravkov.
3) Don't allow NULL msg->msg_name just because msg->msg_namelen is
non-zero, from Andrey Ryabinin.
4) ndm->ndm_type set using wrong macros, from Jun Zhao.
5) cdc-ether devices can come up with entries in their address filter,
so explicitly clear the filter after the device initializes. From
Oliver Neukum.
6) Forgotten refcount bump in xfrm_lookup(), from Steffen Klassert.
7) Short packets not padded properly, exposing random data, in bcmgenet
driver. Fix from Florian Fainelli.
8) xgbe_probe() doesn't return an error code, but rather zero, when
netif_set_real_num_tx_queues() fails. Fix from Wei Yongjun.
9) USB speed not probed properly in r8152 driver, from Hayes Wang.
10) Transmit logic choosing the outgoing port in the sunvnet driver
needs to consider a) is the port actually up and b) whether it is a
switch port. Fix from David L Stevens.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
net: phy: re-apply PHY fixups during phy_register_device
cdc-ether: clean packet filter upon probe
cdc_subset: deal with a device that needs reset for timeout
net: sendmsg: fix NULL pointer dereference
isdn/bas_gigaset: fix a leak on failure path in gigaset_probe()
ip: make IP identifiers less predictable
neighbour : fix ndm_type type error issue
sunvnet: only use connected ports when sending
can: c_can_platform: Fix raminit, use devm_ioremap() instead of devm_ioremap_resource()
bnx2x: fix crash during TSO tunneling
r8152: fix the checking of the usb speed
net: phy: Ensure the MDIO bus module is held
net: phy: Set the driver when registering an MDIO bus device
bnx2x: fix set_setting for some PHYs
hyperv: Fix error return code in netvsc_init_buf()
amd-xgbe: Fix error return code in xgbe_probe()
ath9k: fix aggregation session lockup
net: bcmgenet: correctly pad short packets
net: sctp: inherit auth_capable on INIT collisions
mac80211: fix crash on getting sta info with uninitialized rate control
...
Remove a prototype which was added by both 93c4adc7af and 36be0b9deb.
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The WARN_ON() is used to check if we break the legal hierarchy, on
which the effective mems should be equal to configured mems.
Reported-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Tested-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Li Zefan <lizefan@huawei.com>
The references to the device state are not dropped
everywhere. This might cause a dead-lock in
amd_iommu_free_device(). Fix it.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Oded Gabbay <oded.gabbay@amd.com>
All calls to this call-back are wrapped with
mmu_notifer_invalidate_range_start()/end(), making this
notifier pretty useless, so remove it.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Oded Gabbay <oded.gabbay@amd.com>
With calling te mmu_notifier_register function we hold a
reference to the mm_struct that needs to be released in
mmu_notifier_unregister. This is true even if the notifier
was already unregistered from exit_mmap and the .release
call-back has already run.
So make sure we call mmu_notifier_unregister unconditionally
in amd_iommu_unbind_pasid.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Oded Gabbay <oded.gabbay@amd.com>
Building a kernel with CPU_BIG_ENDIAN fails if there are stale objects
from a !CPU_BIG_ENDIAN build. Due to a missing FORCE prerequisite on an
if_changed rule in the VDSO Makefile, we attempt to link a stale LE
object into the new BE kernel.
According to Documentation/kbuild/makefiles.txt, FORCE is required for
if_changed rules and forgetting it is a common mistake, so fix it by
'Forcing' the build of vdso. This patch fixes build errors like these:
arch/arm64/kernel/vdso/note.o: compiled for a little endian system and target is big endian
failed to merge target specific data of file arch/arm64/kernel/vdso/note.o
arch/arm64/kernel/vdso/sigreturn.o: compiled for a little endian system and target is big endian
failed to merge target specific data of file arch/arm64/kernel/vdso/sigreturn.o
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arun Chandran <achandran@mvista.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This pci fixup routine calls __init functions.
In general pci fixup routine must not call __init functions,
but this pci/isa bridge device is not hotpluggable anyway.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7215/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes a regression caused by commit
bb6c0bd3fd [MIPS: SB1: Fix excessive kernel
warnings.], that makes `-march=r5000' selected for compilation flags
rather than supposed `-march=sb1' with compilers that do not support the
ASE selection flags introduced with that change.
For example GCC 4.1.2 supports `-mips3d'/`-mno-mips3d' (and obviously
`-march=sb1'), however it does not support `-mdmx'/`-mno-mdmx'. As a
result the whole selection of flags fails and compilation resorts to using
`-march=r5000', meant for really old compilers indeed only.
It is always best to pick the flags individually unless we are absolutely
sure a set of flags was introduced to the toolchain together (`-march=sb1'
and `-mtune=sb1' would be a good example), and this change makes it happen
for CONFIG_CPU_SB1. Consequently the flags ultimately selected with GCC
4.1.2 are `-march=sb1 -Wa,--trap -mno-mips3d'
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Richard Sandiford <rdsandiford@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7223/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes:
{standard input}: Assembler messages:
{standard input}:145: Error: opcode not supported on this processor: vr5000 (mips4) `clz $2,$2'
{standard input}:920: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$9'
{standard input}:1797: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:1851: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:2831: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:4209: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:4329: Error: opcode not supported on this processor: vr5000 (mips4) `clz $2,$2'
make[2]: *** [arch/mips/mm/tlbex.o] Error 1
which triggered due to a regression causing the file to be built with
`-march=r5000' rather than `-march=sb1', fixed separately. Nevertheless
the error should not happen, the other uses of CLZ are appropriately
guarded. This change copies the arrangement from one of those other
places.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7222/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Code in a switch statement in probe_pcache checks the CPU type twice
unnecessarily for processor implementations that have the alias removal
feature reported by the CP0 Config7.AR and Config7.IAR bits. This change
rewrites the affected fragment avoiding the extraneous check and improving
readability.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7221/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The sun6i_dma_prep_memcpy and sun6i_dma_prep_slave_sg functions were both
leaking the descriptor they allocated if an error was happening after a
successful dma_pool_alloc call.
It also fixes a memleak that was happening in the scatter gather list
traversal, that was allocating as much descriptor as there was scatter gather
items, but only freeing the current descriptor if an error was to arise.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There's still a small window between the call to sun6i_kill_tasklet and the end
of the driver remove function where a spurious interrupt might trigger, and
start using deallocated resources.
Replace the call to synchronize_irq by a free_irq, so that we're sure that we
won't get any further interrupts when we're deallocating resources.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the conversion routine is quite trivial, we don't need this switch, and
we can just use a simple calculation.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Select DMA_ENGINE when DMA_OF is selected since
of_dma_xlate_by_chan_id() from drivers/dma/of-dma.c uses
dma_get_slave_channel() from drivers/dma/dmaengine.c
This resolves error reported:
drivers/built-in.o: In function `of_dma_xlate_by_chan_id':
drivers/dma/of-dma.c:253: undefined reference to `dma_get_slave_channel'
Signed-off-by: Alexander Popov <a13xp0p0v88@gmail.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Wire up the set_affinity call for the internal PIC if booting on
a cpu supporting it.
Affinity is kept to boot cpu as default.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7323/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In preparation for applying affinity, use the irq descriptor as the
argument for (un)mask.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7317/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit 7dfc63cf97
(KVM: s390: allow only one SIGP STOP (AND STORE STATUS) at a time)
introduced a memory leak if a sigp stop is already pending. Free
the allocated inti structure.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Since we will have the chance of accessing the registers concurrently,
protect any accesses through a spinlock.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7321/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Set it to zero if there is no second set.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7319/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The SMP capable irq controllers have two interrupt output pins which are
controlled through separate registers, so make the variables arrays.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7318/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The generic version uses a variable length of u32 registers instead of u32/u64.
This allows easier support for "wider" registers without having to rewrite
everything.
This "generic" version is as fast as the old version in the best case
(i == next set bit), and twice as fast in the worst case in 64 bits.
Using a macro was chosen over a (forced) inline version because gcc generated
more compact code with the macro.
The change from (signed) int to unsigned int for i and to_call was intentional
as the value can be only between 0 and (width - 1) anyway, and allowed gcc to
optimise the code a bit further.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7316/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
