This fixes the following error caused by a race condition between
phydev->adjust_link() and a MDIO transaction in the phy interrupt
handler. The issue was reproduced with the ethernet FEC driver and a
micrel KSZ9031 phy.
[ 146.195696] fec 2188000.ethernet eth0: MDIO read timeout
[ 146.201779] ------------[ cut here ]------------
[ 146.206671] WARNING: CPU: 0 PID: 571 at drivers/net/phy/phy.c:942 phy_error+0x24/0x6c
[ 146.214744] Modules linked in: bnep imx_vdoa imx_sdma evbug
[ 146.220640] CPU: 0 PID: 571 Comm: irq/128-2188000 Not tainted 5.18.0-rc3-00080-gd569e86915b7 #9
[ 146.229563] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 146.236257] unwind_backtrace from show_stack+0x10/0x14
[ 146.241640] show_stack from dump_stack_lvl+0x58/0x70
[ 146.246841] dump_stack_lvl from __warn+0xb4/0x24c
[ 146.251772] __warn from warn_slowpath_fmt+0x5c/0xd4
[ 146.256873] warn_slowpath_fmt from phy_error+0x24/0x6c
[ 146.262249] phy_error from kszphy_handle_interrupt+0x40/0x48
[ 146.268159] kszphy_handle_interrupt from irq_thread_fn+0x1c/0x78
[ 146.274417] irq_thread_fn from irq_thread+0xf0/0x1dc
[ 146.279605] irq_thread from kthread+0xe4/0x104
[ 146.284267] kthread from ret_from_fork+0x14/0x28
[ 146.289164] Exception stack(0xe6fa1fb0 to 0xe6fa1ff8)
[ 146.294448] 1fa0: 00000000 00000000 00000000 00000000
[ 146.302842] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 146.311281] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 146.318262] irq event stamp: 12325
[ 146.321780] hardirqs last enabled at (12333): [<c01984c4>] __up_console_sem+0x50/0x60
[ 146.330013] hardirqs last disabled at (12342): [<c01984b0>] __up_console_sem+0x3c/0x60
[ 146.338259] softirqs last enabled at (12324): [<c01017f0>] __do_softirq+0x2c0/0x624
[ 146.346311] softirqs last disabled at (12319): [<c01300ac>] __irq_exit_rcu+0x138/0x178
[ 146.354447] ---[ end trace 0000000000000000 ]---
With the FEC driver phydev->adjust_link() calls fec_enet_adjust_link()
calls fec_stop()/fec_restart() and both these function reset and
temporary disable the FEC disrupting any MII transaction that
could be happening at the same time.
fec_enet_adjust_link() and phy_read() can be running at the same time
when we have one additional interrupt before the phy_state_machine() is
able to terminate.
Thread 1 (phylib WQ) | Thread 2 (phy interrupt)
|
| phy_interrupt() <-- PHY IRQ
| handle_interrupt()
| phy_read()
| phy_trigger_machine()
| --> schedule phylib WQ
|
|
phy_state_machine() |
phy_check_link_status() |
phy_link_change() |
phydev->adjust_link() |
fec_enet_adjust_link() |
--> FEC reset | phy_interrupt() <-- PHY IRQ
| phy_read()
|
Fix this by acquiring the phydev lock in phy_interrupt().
Link: https://lore.kernel.org/all/20220422152612.GA510015@francesco-nb.int.toradex.com/
Fixes: c974bdbc3e ("net: phy: Use threaded IRQ, to allow IRQ from sleeping devices")
cc: <stable@vger.kernel.org>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220506060815.327382-1-francesco.dolcini@toradex.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The func_id parameter in find_kfunc_desc_btf() is not used, get rid of it.
Fixes: 2357672c54 ("bpf: Introduce BPF support for kernel module function calls")
Signed-off-by: Yuntao Wang <ytcoode@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/bpf/20220505070114.3522522-1-ytcoode@gmail.com
samples/bpf build currently always fails if it can't generate
vmlinux.h from vmlinux, even when vmlinux.h is directly provided by
VMLINUX_H variable, which makes VMLINUX_H pointless.
Only fails when neither method works.
Fixes: 384b6b3bbf ("samples: bpf: Add vmlinux.h generation support")
Reported-by: CKI Project <cki-project@redhat.com>
Reported-by: Veronika Kabatova <vkabatov@redhat.com>
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220507161635.2219052-1-jmarchan@redhat.com
The tools/testing/selftests/vm/Makefile uses the variable TARGETS
internally to generate a list of platform-specific binary build targets
suffixed with _{32,64}. When building the selftests using its own
Makefile directly, such as via the following command run in a kernel tree:
One receives an error such as the following:
make: Entering directory '/root/linux/tools/testing/selftests'
make --no-builtin-rules ARCH=x86 -C ../../.. headers_install
make[1]: Entering directory '/root/linux'
INSTALL ./usr/include
make[1]: Leaving directory '/root/linux'
make[1]: Entering directory '/root/linux/tools/testing/selftests/vm'
make[1]: *** No rule to make target 'vm.c', needed by '/root/linux/tools/testing/selftests/vm/vm_64'. Stop.
make[1]: Leaving directory '/root/linux/tools/testing/selftests/vm'
make: *** [Makefile:175: all] Error 2
make: Leaving directory '/root/linux/tools/testing/selftests'
The TARGETS variable passed to tools/testing/selftests/Makefile collides
with the TARGETS used in tools/testing/selftests/vm/Makefile, so rename
the latter to VMTARGETS, eliminating the collision with no functional
change.
Link: https://lkml.kernel.org/r/20220504213454.1282532-1-jsavitz@redhat.com
Fixes: f21fda8f64 ("selftests: vm: pkeys: fix multilib builds for x86")
Signed-off-by: Joel Savitz <jsavitz@redhat.com>
Acked-by: Nico Pache <npache@redhat.com>
Cc: Joel Savitz <jsavitz@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Sandipan Das <sandipan@linux.ibm.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Separate linux.intel.com account was created for submitting and reviewing
kernel patches, thus need to map previously used primary Intel e-mail
address.
Link: https://lkml.kernel.org/r/20220505132624.41802-1-martyna.szapar-mudlaw@linux.intel.com
Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The semantics of pfn_valid() is to check presence of the memory map for a
PFN and not whether a PFN is covered by the linear map. The memory map
may be present for NOMAP memory regions, but they won't be mapped in the
linear mapping. Accessing such regions via __va() when they are
memremap()'ed will cause a crash.
On v5.4.y the crash happens on qemu-arm with UEFI [1]:
<1>[ 0.084476] 8<--- cut here ---
<1>[ 0.084595] Unable to handle kernel paging request at virtual address dfb76000
<1>[ 0.084938] pgd = (ptrval)
<1>[ 0.085038] [dfb76000] *pgd=5f7fe801, *pte=00000000, *ppte=00000000
...
<4>[ 0.093923] [<c0ed6ce8>] (memcpy) from [<c16a06f8>] (dmi_setup+0x60/0x418)
<4>[ 0.094204] [<c16a06f8>] (dmi_setup) from [<c16a38d4>] (arm_dmi_init+0x8/0x10)
<4>[ 0.094408] [<c16a38d4>] (arm_dmi_init) from [<c0302e9c>] (do_one_initcall+0x50/0x228)
<4>[ 0.094619] [<c0302e9c>] (do_one_initcall) from [<c16011e4>] (kernel_init_freeable+0x15c/0x1f8)
<4>[ 0.094841] [<c16011e4>] (kernel_init_freeable) from [<c0f028cc>] (kernel_init+0x8/0x10c)
<4>[ 0.095057] [<c0f028cc>] (kernel_init) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
On kernels v5.10.y and newer the same crash won't reproduce on ARM because
commit b10d6bca87 ("arch, drivers: replace for_each_membock() with
for_each_mem_range()") changed the way memory regions are registered in
the resource tree, but that merely covers up the problem.
On ARM64 memory resources registered in yet another way and there the
issue of wrong usage of pfn_valid() to ensure availability of the linear
map is also covered.
Implement arch_memremap_can_ram_remap() on ARM and ARM64 to prevent access
to NOMAP regions via the linear mapping in memremap().
Link: https://lore.kernel.org/all/Yl65zxGgFzF1Okac@sirena.org.uk
Link: https://lkml.kernel.org/r/20220426060107.7618-1-rppt@kernel.org
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Tested-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org> [5.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The file permissions on the fdinfo dir from were changed from
S_IRUSR|S_IXUSR to S_IRUGO|S_IXUGO, and a PTRACE_MODE_READ check was added
for opening the fdinfo files [1]. However, the ptrace permission check
was not added to the directory, allowing anyone to get the open FD numbers
by reading the fdinfo directory.
Add the missing ptrace permission check for opening the fdinfo directory.
[1] https://lkml.kernel.org/r/20210308170651.919148-1-kaleshsingh@google.com
Link: https://lkml.kernel.org/r/20210713162008.1056986-1-kaleshsingh@google.com
Fixes: 7bc3fa0172 ("procfs: allow reading fdinfo with PTRACE_MODE_READ")
Signed-off-by: Kalesh Singh <kaleshsingh@google.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Hridya Valsaraju <hridya@google.com>
Cc: Jann Horn <jannh@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The mremap syscall is supposed to return a pointer to the new virtual
memory area on success, and a negative value of the error code in case of
failure. Currently, EFAULT is returned when the VMA is not found, instead
of -EFAULT. The users of this syscall will therefore believe the syscall
succeeded in case the VMA didn't exist, as it returns a pointer to address
0xe (0xe being the value of EFAULT). Fix the sign of the error value.
Link: https://lkml.kernel.org/r/20220427224439.23828-2-dossche.niels@gmail.com
Fixes: 550a7d60bd ("mm, hugepages: add mremap() support for hugepage backed vma")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Building with SENSORS_LTQ_CPUTEMP=y with SOC_FALCON=y causes build
errors since FALCON does not support the same features as XWAY.
Change this symbol to depend on SOC_XWAY since that provides the
necessary interfaces.
Repairs these build errors:
../drivers/hwmon/ltq-cputemp.c: In function 'ltq_cputemp_enable':
../drivers/hwmon/ltq-cputemp.c:23:9: error: implicit declaration of function 'ltq_cgu_w32'; did you mean 'ltq_ebu_w32'? [-Werror=implicit-function-declaration]
23 | ltq_cgu_w32(ltq_cgu_r32(CGU_GPHY1_CR) | CGU_TEMP_PD, CGU_GPHY1_CR);
../drivers/hwmon/ltq-cputemp.c:23:21: error: implicit declaration of function 'ltq_cgu_r32'; did you mean 'ltq_ebu_r32'? [-Werror=implicit-function-declaration]
23 | ltq_cgu_w32(ltq_cgu_r32(CGU_GPHY1_CR) | CGU_TEMP_PD, CGU_GPHY1_CR);
../drivers/hwmon/ltq-cputemp.c: In function 'ltq_cputemp_probe':
../drivers/hwmon/ltq-cputemp.c:92:31: error: 'SOC_TYPE_VR9_2' undeclared (first use in this function)
92 | if (ltq_soc_type() != SOC_TYPE_VR9_2)
Fixes: 7074d0a927 ("hwmon: (ltq-cputemp) add cpu temp sensor driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Florian Eckert <fe@dev.tdt.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20220509234740.26841-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The W=2 build pointed out that the code wasn't initializing all the
variables in the dim_cq_moder declarations with the struct initializers.
The net change here is zero since these structs were already static
const globals and were initialized with zeros by the compiler, but
removing compiler warnings has value in and of itself.
lib/dim/net_dim.c: At top level:
lib/dim/net_dim.c:54:9: warning: missing initializer for field ‘comps’ of ‘const struct dim_cq_moder’ [-Wmissing-field-initializers]
54 | NET_DIM_RX_EQE_PROFILES,
| ^~~~~~~~~~~~~~~~~~~~~~~
In file included from lib/dim/net_dim.c:6:
./include/linux/dim.h:45:13: note: ‘comps’ declared here
45 | u16 comps;
| ^~~~~
and repeats for the tx struct, and once you fix the comps entry then
the cq_period_mode field needs the same treatment.
Use the commonly accepted style to indicate to the compiler that we
know what we're doing, and add a comma at the end of each struct
initializer to clean up the issue, and use explicit initializers
for the fields we are initializing which makes the compiler happy.
While here and fixing these lines, clean up the code slightly with
a fix for the super long lines by removing the word "_MODERATION" from a
couple defines only used in this file.
Fixes: f8be17b81d ("lib/dim: Fix -Wunused-const-variable warnings")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20220507011038.14568-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The initial code used roundup() to round the starting time to
a multiple of a period. This generated an error on 32-bit
systems, so was replaced with DIV_ROUND_UP_ULL().
However, this truncates to 32-bits on a 64-bit system. Replace
with DIV64_U64_ROUND_UP() instead.
Fixes: b325af3cfa ("ptp: ocp: Add signal generators and update sysfs nodes")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220506223739.1930-2-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Milan Landaverde says:
====================
Currently in bpftool's feature probe, we incorrectly tell the user that
all of the helper functions are supported for program types where helper
probing fails or is explicitly unsupported[1]:
$ bpftool feature probe
...
eBPF helpers supported for program type tracing:
- bpf_map_lookup_elem
- bpf_map_update_elem
- bpf_map_delete_elem
...
- bpf_redirect_neigh
- bpf_check_mtu
- bpf_sys_bpf
- bpf_sys_close
This patch adjusts bpftool to relay to the user when helper support
can't be determined:
$ bpftool feature probe
...
eBPF helpers supported for program type lirc_mode2:
Program type not supported
eBPF helpers supported for program type tracing:
Could not determine which helpers are available
eBPF helpers supported for program type struct_opts:
Could not determine which helpers are available
eBPF helpers supported for program type ext:
Could not determine which helpers are available
Rather than imply that no helpers are available for the program type, we
let the user know that helper function probing failed entirely.
[1] https://lore.kernel.org/bpf/20211217171202.3352835-2-andrii@kernel.org/
====================
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Currently in libbpf, we have hardcoded program types that are not
supported for helper function probing (e.g. tracing, ext, lsm).
Due to this (and other legitimate failures), bpftool feature probe returns
empty for those program type helper functions.
Instead of implying to the user that there are no helper functions
available for a program type, we output a message to the user explaining
that helper function probing failed for that program type.
Signed-off-by: Milan Landaverde <milan@mdaverde.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220504161356.3497972-3-milan@mdaverde.com
IF CONFIG_SYSCTL is n, build warn:
kernel/sched/core.c:1782:12: warning: ‘sysctl_sched_uclamp_handler’ defined but not used [-Wunused-function]
static int sysctl_sched_uclamp_handler(struct ctl_table *table, int write,
^~~~~~~~~~~~~~~~~~~~~~~~~~~
sysctl_sched_uclamp_handler() is used while CONFIG_SYSCTL enabled,
wrap all related code with CONFIG_SYSCTL to fix this.
Fixes: 3267e0156c ("sched: Move uclamp_util sysctls to core.c")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
If CONFIG_SYSCTL is n, build warn:
kernel/reboot.c:443:20: error: ‘kernel_reboot_sysctls_init’ defined but not used [-Werror=unused-function]
static void __init kernel_reboot_sysctls_init(void)
^~~~~~~~~~~~~~~~~~~~~~~~~~
Move kernel_reboot_sysctls_init() to #ifdef block to fix this.
Fixes: 06d177662f ("kernel/reboot: move reboot sysctls to its own file")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Unfortunately the design of fscrypt_set_test_dummy_encryption() doesn't
work properly for the new mount API, as it combines too many steps into
one function:
- Parse the argument to test_dummy_encryption
- Check the setting against the filesystem instance
- Apply the setting to the filesystem instance
The new mount API has split these into separate steps. ext4 partially
worked around this by duplicating some of the logic, but it still had
some bugs. To address this, add some new helper functions that split up
the steps of fscrypt_set_test_dummy_encryption():
- fscrypt_parse_test_dummy_encryption()
- fscrypt_dummy_policies_equal()
- fscrypt_add_test_dummy_key()
While we're add it, also add a function fscrypt_is_dummy_policy_set()
which will be useful to avoid some #ifdef's.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20220501050857.538984-5-ebiggers@kernel.org
Factor out a function that builds the fscrypt_key_specifier for an
fscrypt_policy. Before this was only needed when finding the key for a
file, but now it will also be needed for test_dummy_encryption support.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20220501050857.538984-4-ebiggers@kernel.org
Fix the missing pci_disable_device() before return
from tulip_init_one() in the error handling case.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220506094250.3630615-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Closely following the outline of Mel Gorman's book "Understanding the
Linux Virtual Memory Manager", add a new outline. Preserve the current
contents of the mm underneath the new outline so we can transition those
documents to a more sensible place later.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Link: https://lore.kernel.org/r/20220507134947.444287-1-willy@infradead.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Drop ide-* command line options.
Drop cdrom/ide-cd.rst documentation.
Fixes: 898ee22c32 ("Drop Documentation/ide/")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220424033701.7988-1-rdunlap@infradead.org
[jc: also deleted reference from cdrom/index.rst]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Explain that, when collecting list of people to Cc the patch,
scripts/get_maintainer.pl should be used on patches, not on the
directories. The behavior is quite different, because with "-f" on
a directory, the maintainers of individual files will not be shown.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220427185645.677039-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Due to the lack of an entry for the Japanese translation of
documentation, Kosuke Fujimoto needed to ask the status of
its maintenance [1].
Add an entry for DOCUMENTATION/JAPANESE as a sub-subsystem
under the DOCUMENTATION subsystem to make it easier for
another prospective contributor to know there is someone
who takes care of Japanese translation.
As a first step, install myself as a designated reviewer.
Hopefully, other interested members get accustomed to the
kernel-dev workflow and would get ready to be
(co-)maintainers/reviewers shortly.
[1]: https://lore.kernel.org/r/172fa015-26df-c978-853d-3aba67c581cc@gmail.com/
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Tsugikazu Shibata <shibata@linuxfoundation.org>
Cc: Kosuke Fujimoto <fujimotokosuke0@gmail.com>
Link: https://lore.kernel.org/r/7689b502-8c34-85b1-54e0-7a3b5e3c2bd1@gmail.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This change is based on commit d2b008f134
("Documentation/process/howto: Update for 4.x -> 5.x versioning").
Replace "4.x kernel version" with generic term such as "mainline tree"
Reviewed-by: Akira Yokosawa <akiyks@gmail.com>
---
V2: Reformatted commit log message (Yokosawa-san)
V3: Updated some expressions (Shibata-san)
- added "version number" in mainline tree section
- updated from "stable kernel" to "stable tree"
V4: Added reviewed by tag and removed extra characters (Yokosawa-san)
V5: Removed an extra character (Shibata-san)
Signed-off-by: Kosuke Fujimoto <fujimotokosuke0@gmail.com>
Acked-by: Tsugikazu Shibata <shibata@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220501102256.6379-1-fujimotokosuke0@gmail.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Reflect changes made in commit 0af5270324
("Documentation/SubmittingPatches: Request summaries for commit
references").
Note: Translated paragraph uses a slightly different structure and
omit a redundant phrase so that they are easier to follow.
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Cc: Tsugikazu Shibata <shibata@linuxfoundation.org>
Cc: Kosuke Fujimoto <fujimotokosuke0@gmail.com>
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Tsugikazu Shibata <shibata@linuxfoundation.org>
Reviewed-by: Kosuke Fujimoto <fujimotokosuke0@gmail.com>
Link: https://lore.kernel.org/r/20220503104820.49269-1-akiyks@gmail.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- New board support: Engicam i.Core MX8M Plus SoM and EDIMM2.2 Starter
Kit, Toradex Verdin i.MX8M Plus devices, Data Modul i.MX8M Mini eDM SBC,
Verdin based MX8Menlo, 8MNANOD3L EVK, i.MX8M Plus Gateworks GW7400.
- Enable RTS-CTS on UART3 for imx8mm-beacon and imx8mn-beacon boards.
- Enable HS400-ES support for i.MX8MN and i.MX8MP uSDHC devices by
updating the compatible.
- A few updates on imx8mq-librem5 to increase boost regulation
current, add panel compatible for r4 ("Evergreen") revision and volume
buttons a wakeup source.
- Clean up vendor specific 'fsl,uart-has-rtscts' property by using
standard 'uart-has-rtscts'.
- Add GPC, GPU, MEDIAMIX, and HSIO power domains for i.MX8M Plus SoC.
- A series from Marcel Ziswiler to improve imx8mm-verdin support,
including cosmetic changes and functional improvements like SD1 sleep
pinctrl and fully validated IOMUX configuration.
- Add PWM polarity inversion support for i.MX8 SoCs.
- A couple of changes from Michael Walle to update PMIC output names and
min/max voltages for imx8mn-evk board.
- A series from Tim Harvey to improve imx8mm-venice boards, add missing
uart-has-rtscts property to UARTs, clock-names to pcie_phy, and
vdd_5p0 ADC channel.
- Add VPU codec devices for i.MX8QXP SoC.
- Other small and random changes.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmJ3N+4UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM748QgAt12d3nU7Eh3TbnpYO2ofVGv/JzNJ
jUvyP5DzuxmFh9wvs50QuH7AkHjoBHh52cOxy0jHUJDvOF6o0UlUZjmhDmBK9hSh
U7gnr+y3im7lZQNaPI5ECZcxPR7cStW3z2YDsdhx4eL6jn2Rh5kCdpOWbKqhaBEJ
eQQEuY03GU7t+3BjwroTk1njyn6hH21NCskQCL1wR+B76z/0JtmocsNhwUjTmdvt
+jMuHu2PMStbu8K0Eb45bsdKSk46TwQUeF9NDSDELuzYtA/XdWe7iBZd3NjlbFxY
8mHBzF8poum3seA8XJA/O00KGhqGhKawIlMlQZCtxi8L0CxgEXABUFYsDA==
=07f+
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=dgZt
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree update for 5.19:
- New board support: Engicam i.Core MX8M Plus SoM and EDIMM2.2 Starter
Kit, Toradex Verdin i.MX8M Plus devices, Data Modul i.MX8M Mini eDM SBC,
Verdin based MX8Menlo, 8MNANOD3L EVK, i.MX8M Plus Gateworks GW7400.
- Enable RTS-CTS on UART3 for imx8mm-beacon and imx8mn-beacon boards.
- Enable HS400-ES support for i.MX8MN and i.MX8MP uSDHC devices by
updating the compatible.
- A few updates on imx8mq-librem5 to increase boost regulation
current, add panel compatible for r4 ("Evergreen") revision and volume
buttons a wakeup source.
- Clean up vendor specific 'fsl,uart-has-rtscts' property by using
standard 'uart-has-rtscts'.
- Add GPC, GPU, MEDIAMIX, and HSIO power domains for i.MX8M Plus SoC.
- A series from Marcel Ziswiler to improve imx8mm-verdin support,
including cosmetic changes and functional improvements like SD1 sleep
pinctrl and fully validated IOMUX configuration.
- Add PWM polarity inversion support for i.MX8 SoCs.
- A couple of changes from Michael Walle to update PMIC output names and
min/max voltages for imx8mn-evk board.
- A series from Tim Harvey to improve imx8mm-venice boards, add missing
uart-has-rtscts property to UARTs, clock-names to pcie_phy, and
vdd_5p0 ADC channel.
- Add VPU codec devices for i.MX8QXP SoC.
- Other small and random changes.
* tag 'imx-dt64-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (65 commits)
arm64: dt: imx8mp: support pwm polarity inversion
arm64: dt: imx8mn: support pwm polarity inversion
arm64: dt: imx8mm: support pwm polarity inversion
arm64: dt: imx8mq: support pwm polarity inversion
arm64: dts: imx8mm-venice-gw7901: remove unnecessary cpu temp override
arm64: dts: imx8mm-venice-gw7902: add vdd_5p0 ADC channel
arm64: dts: imx8m*venice: add missing clock-names to pcie_phy
arm64: dts: imx8mm-venice-gw7902: fix pcie bindings
arm64: dts: freescale: reduce the interrup-map-mask
arm64: dts: imx8mn-beacon: Enable RTS-CTS on UART3
arm64: dts: imx8mm-beacon: Enable RTS-CTS on UART3
arm64: dts: imx8mm: Use 100 kHz I2C2 on Data Modul i.MX8M Mini eDM SBC
arm64: dts: imx8mm: Disable USB2 OC on Data Modul i.MX8M Mini eDM SBC
arm64: dts: imx8mm: Add CPLD on MX8Menlo board
arm64: dts: imx8mq-kontron-pitx-imx8m: Use the standard 'uart-has-rtscts'
arm64: dts: imx8mp-verdin: Use the standard 'uart-has-rtscts'
arm64: dts: imx8mp: Add MEDIA_BLK_CTRL
arm64: dts: imx8mp: Add MEDIAMIX power domains
arm64: dts: imx8mp: add HSIO power-domains
arm64: dts: imx8mp: Add Engicam i.Core MX8M Plus EDIMM2.2 Starter Kit
...
Link: https://lore.kernel.org/r/20220508033843.2773685-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- New board support: PHYTEC phyGATE-Tauri-S, TQ-Systems MBa6UL,
LS1021A IoT board, Toradex Iris and Aster carrier, i.MX7D SMEGW01,
i.MXRT1050 EVK, Bosch ACC board.
- A series from Alexander Stein to update i.MX51 based digi-connectcore
board, regarding to DMA of UART devices, PMIC voltages, USB
vbus-supply and usbphy.
- A series of changes from David Jander and Oleksij Rempel to remove
prototype specific deprecated code not used in production from
i.MX6Q/DL Vicut1 board, and unify Vicut1 and Victgo variants to reduce
maintaining overhead.
- Quite some changes from different people to update imx6ull-colibri board
on various aspects, touchscreen, device tree overlays, NAND BCH geometry,
GPIO line names, FEC phy-supply, etc.
- A couple of changes from Fabio Estevam to switch imx6dl-plybas and
imx6ul-kontron-n6x1x-s to use standard 'uart-has-rtscts' property.
- A couple of patches from Li Yang to update IFC device compatible and
node name for LayerScape SoCs.
- Disable USB host to work around boot issue on imx6qdl-udoo board.
- A series from Max Krummenacher to update Colibri i.MX6DL device trees,
drop dedicated v1.1 DT, disable add-on accessories, cleanups, etc.
- Various random and small updates on i.MX28 and i.MX6 boards.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmJ3Lh0UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5/aggArNGwQjG38N4EKh+VZZChUhYz1qFz
n53ciWQokLItUpO3FOXvVVVR1avBAHorUe2gcnpaFmQbIuDgxpjw9xEfsXUaiKGC
UD+zU2iNaabaaqOoKii/eVUOMuoRO96gFtR0XUyYyg9JPnmy+2a25cVfJ6Kev6AJ
727xpoFexbXbiJSl/3TR2vJBD2cmGllrgiPgzUYFe7aPXwZyTYp6WRLkdhjdBFty
4Up+7Img4FVkxVrDHv4TO2sxLMAftQM05/KjMCeRzEslvh/81IUnXA1i0TPqnKZJ
P1KFl7hd0/5DqsCji7Eel2zbRRq75HPSPIacdXbWiEzcJBY8FBZcFdcf7Q==
=zcPw
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=JH1/
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX ARM device tree update for 5.19:
- New board support: PHYTEC phyGATE-Tauri-S, TQ-Systems MBa6UL,
LS1021A IoT board, Toradex Iris and Aster carrier, i.MX7D SMEGW01,
i.MXRT1050 EVK, Bosch ACC board.
- A series from Alexander Stein to update i.MX51 based digi-connectcore
board, regarding to DMA of UART devices, PMIC voltages, USB
vbus-supply and usbphy.
- A series of changes from David Jander and Oleksij Rempel to remove
prototype specific deprecated code not used in production from
i.MX6Q/DL Vicut1 board, and unify Vicut1 and Victgo variants to reduce
maintaining overhead.
- Quite some changes from different people to update imx6ull-colibri board
on various aspects, touchscreen, device tree overlays, NAND BCH geometry,
GPIO line names, FEC phy-supply, etc.
- A couple of changes from Fabio Estevam to switch imx6dl-plybas and
imx6ul-kontron-n6x1x-s to use standard 'uart-has-rtscts' property.
- A couple of patches from Li Yang to update IFC device compatible and
node name for LayerScape SoCs.
- Disable USB host to work around boot issue on imx6qdl-udoo board.
- A series from Max Krummenacher to update Colibri i.MX6DL device trees,
drop dedicated v1.1 DT, disable add-on accessories, cleanups, etc.
- Various random and small updates on i.MX28 and i.MX6 boards.
* tag 'imx-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (77 commits)
ARM: dts: imx6ull-colibri: improve pinctrl node names
ARM: dts: imx6ull-colibri: move gpio-keys node to som dtsi
ARM: dts: imx6ull-colibri: add/update some comments
ARM: dts: imx6ull-colibri: fix nand bch geometry
ARM: dts: imx6ull-colibri: add support for toradex aster carrier boards
ARM: dts: imx6ull-colibri: add support for toradex iris carrier boards
ARM: dts: imx6ull-colibri: add gpio-line-names
ARM: dts: imx6ull-colibri: update device trees to support overlays
ARM: dts: imx6ull-colibri: update usdhc1 pixmux and signaling
ARM: dts: imx6ull-colibri: add touchscreen device nodes
ARM: dts: imx6ull-colibri: add phy-supply to fec
ARM: dts: imx6ull-colibri: change touch i2c parameters
ARM: dts: imx6ull-colibri: use pull-down for adc pins
ARM: dts: Add bosch acc board
ARM: dts: imx: Add i.MXRT1050-EVK support
ARM: dts: imx7d-smegw01: Add support for i.MX7D SMEGW01 board
ARM: dts: imx6qdl-udoo: Disable USB host to work around boot issues
ARM: dts: imx27: use new 'dma-channels' property
ARM: dts: imx6qdl-phytec: Add LED labels
ARM: dts: ls1021a: reduce the interrupt-map-mask
...
Link: https://lore.kernel.org/r/20220508033843.2773685-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds MDIO bus description on the IPQ6018 platform.
On MSM8916 the BAM-DMUX WWAN network device is added and the Huawei
Ascend G7 gains sound card definition and clarified installation
instructions.
MSM8992 and MSM8994 continues to be worked on, gaining multimedia clock
controller, on-chip memory, watchdog and various cleanup changes. The
Xiaomi Mi 4C gains CPU regulators and fixes to the framebuffer
definition, while Huawei Nexus 6P gains eMMC support.
On MSM8996 the modem and sensor remtoeprocs are added and enabled in the
Dragonboard 820c and the Xiaomi devices.
On MSM8998 a few newly added clocks related to the sensor subsystem bus
are marked as protected by default and the OnePlus devices gains NFC.
The SC7180 platform and devices thereon are further polished and
limozeen moves to using edp-panel for EDID-based detection, over
statically defined panels.
On SC7280 GPI DMA, WiFi remoteproc and network device, LPASS audio
clocks, resets for SDCC controllers and a new CRD revision are added. A
supply glitch on the PCIe power and a current leak for Bluetooth during
suspend are corrected. The Herobrine board gains eDP support and the IDP
gains backlight. USB is marked wakeup capable.
On SDM845 the IPA, WLED based backlight and second WiFi channel are
enabled for Xiaomi Pocophone F1, the firmware name is modified to not
conflict with other boards. On RB3 the CAN bus controller is added and
the WiFi calibration variant is defined to allow adding the board's
calibration information into linux-firmware.
SM6350 gains I2C busses, UFS and WiFi support, and the numbering of
uart9 is corrected.
On SM7225 and the Fairphone 4 UFS, WiFi and haptics are enabled.
On SM8150 PCIe, Ethernet and uSD card support is added, and enabled for
the SA8155p ADP board. The PDC interrupt controller is also added and
described as wakup interrupt parent for TLMM.
Camera subsystem and control interface are defined for SM8250. On the
Sony Xperia 1 II the audio amplifiers are enabled.
On SM8350 GPI DMA engines are added and linked to the I2C and SPI
serial engines. Surface Duo 2 gains battery charger support.
On SM8450 the two PCIe controller/PHYs are enabled, GPI DMA and QUP
serial engine instances are added. Remoteproc instances are enabled on
SM8450 HDK.
Last, but not least, a number of DeviceTree validation errors across
various boards are corrected.
-----BEGIN PGP SIGNATURE-----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=cBVa
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=MmN1
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 DT updates for v5.19
This adds MDIO bus description on the IPQ6018 platform.
On MSM8916 the BAM-DMUX WWAN network device is added and the Huawei
Ascend G7 gains sound card definition and clarified installation
instructions.
MSM8992 and MSM8994 continues to be worked on, gaining multimedia clock
controller, on-chip memory, watchdog and various cleanup changes. The
Xiaomi Mi 4C gains CPU regulators and fixes to the framebuffer
definition, while Huawei Nexus 6P gains eMMC support.
On MSM8996 the modem and sensor remtoeprocs are added and enabled in the
Dragonboard 820c and the Xiaomi devices.
On MSM8998 a few newly added clocks related to the sensor subsystem bus
are marked as protected by default and the OnePlus devices gains NFC.
The SC7180 platform and devices thereon are further polished and
limozeen moves to using edp-panel for EDID-based detection, over
statically defined panels.
On SC7280 GPI DMA, WiFi remoteproc and network device, LPASS audio
clocks, resets for SDCC controllers and a new CRD revision are added. A
supply glitch on the PCIe power and a current leak for Bluetooth during
suspend are corrected. The Herobrine board gains eDP support and the IDP
gains backlight. USB is marked wakeup capable.
On SDM845 the IPA, WLED based backlight and second WiFi channel are
enabled for Xiaomi Pocophone F1, the firmware name is modified to not
conflict with other boards. On RB3 the CAN bus controller is added and
the WiFi calibration variant is defined to allow adding the board's
calibration information into linux-firmware.
SM6350 gains I2C busses, UFS and WiFi support, and the numbering of
uart9 is corrected.
On SM7225 and the Fairphone 4 UFS, WiFi and haptics are enabled.
On SM8150 PCIe, Ethernet and uSD card support is added, and enabled for
the SA8155p ADP board. The PDC interrupt controller is also added and
described as wakup interrupt parent for TLMM.
Camera subsystem and control interface are defined for SM8250. On the
Sony Xperia 1 II the audio amplifiers are enabled.
On SM8350 GPI DMA engines are added and linked to the I2C and SPI
serial engines. Surface Duo 2 gains battery charger support.
On SM8450 the two PCIe controller/PHYs are enabled, GPI DMA and QUP
serial engine instances are added. Remoteproc instances are enabled on
SM8450 HDK.
Last, but not least, a number of DeviceTree validation errors across
various boards are corrected.
* tag 'qcom-arm64-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (150 commits)
arm64: dts: qcom: Only include sc7180.dtsi in sc7180-trogdor.dtsi
arm64: dts: qcom: sc7180-trogdor: Simplify spi0/spi6 labeling
arm64: dts: qcom: sc7180-trogdor: Simplify trackpad enabling
arm64: dts: qcom: sc7280: eDP for herobrine boards
arm64: dts: qcom: sa8155p-adp: Disable multiple Tx and Rx queues for ethernet IP
arm64: dts: qcom: sm8150: Fix iommu sid value for SDC2 controller
arm64: dts: qcom: sm8350-duo2: enable battery charger
arm64: dts: qcom: Enable pm8350c pwm for sc7280-idp2
arm64: dts: qcom: pm8350c: Add pwm support
arm64: dts: qcom: sc7280-qcard: Configure CTS pin to bias-bus-hold for bluetooth
arm64: dts: qcom: sc7280-idp: Configure CTS pin to bias-bus-hold for bluetooth
arm64: dts: qcom: sc7180: Remove ipa interconnect node
arm64: dts: qcom: sc7280-idp: Enable GPI DMAs
arm64: dts: qcom: sc7280: Add GENI I2C/SPI DMA channels
arm64: dts: qcom: sc7280: Add GPI DMAengines
arm64: dts: qcom: sm8450: Fix qmp phy node (use phy@ instead of lanes@)
arm64: dts: qcom: db845c: Add support for MCP2517FD
arm64: dts: qcom: qrb5165-rb5: Fix can-clock node name
arm64: dts: qcom: sc7280: Add SAR sensors to herobrine crd
arm64: dts: qcom: sm8250: camss: Add CCI definitions
...
Link: https://lore.kernel.org/r/20220509204451.325675-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This contains a long overdue overhaul of the MSM8974 DeviceTrees,
aligning the style, structure and naming with what we've learned since
the introduction of this platform.
On top of this the Sony Rhine platform gained I2C masters, NFC and
pstore support and the Fairphone 2 gained touchscreen support.
For the new SDX65 platform reserved-memory nodes, rpmpd, SPMI, CPU
clocks, SDHCI controller, SMMU and TCSR mutex was added. As was the
initial DeviceTree for the related PMX65 PMIC.
MSM8226 gained VADC and RTC support and support for the ASUS ZenWatch 2
was added.
-----BEGIN PGP SIGNATURE-----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=WO3I
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=5dY7
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM DT updates for v5.19
This contains a long overdue overhaul of the MSM8974 DeviceTrees,
aligning the style, structure and naming with what we've learned since
the introduction of this platform.
On top of this the Sony Rhine platform gained I2C masters, NFC and
pstore support and the Fairphone 2 gained touchscreen support.
For the new SDX65 platform reserved-memory nodes, rpmpd, SPMI, CPU
clocks, SDHCI controller, SMMU and TCSR mutex was added. As was the
initial DeviceTree for the related PMX65 PMIC.
MSM8226 gained VADC and RTC support and support for the ASUS ZenWatch 2
was added.
* tag 'qcom-dts-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (62 commits)
ARM: dts: qcom: msm8974-FP2: Add supplies for remoteprocs
ARM: dts: qcom: msm8974-FP2: Configure charger
ARM: dts: qcom: msm8974-FP2: Add support for touchscreen
ARM: dts: qcom: sdx55: Remove ipa interconnect node
ARM: dts: qcom: msm8974: Add missing license headers
ARM: dts: qcom: msm8974-FP2: Add mmc* aliases
ARM: dts: qcom: msm8974-FP2: We're msm8974pro
ARM: dts: qcom-msm8974*: Remove unnecessary include
ARM: dts: qcom-msm8974-rhine: Add pstore node
ARM: dts: qcom-msm8974-rhine: Add NFC and enable I2C hosts
ARM: dts: qcom-msm8974*: Clean up old GPIO declarations
ARM: dts: qcom-msm8974*: Consolidate I2C/UART/SDHCI
ARM: dts: qcom-msm8974*: Enable IMEM unconditionally
ARM: dts: qcom-msm8974: Sort and clean up nodes
ARM: dts: qcom-msm8974: Convert ADSP to a MMIO device
ARM: dts: qcom-msm8974pro-*: Use the 8974pro name in DT filenames
ARM: dts: qcom-msm8974pro: Use &labels
ARM: dts: qcom-msm8974-castor: Use &labels
ARM: dts: qcom-msm8974-{"hon","am"}ami: Commonize and modernize the DTs
ARM: dts: qcom-msm8974-klte: Use &labels
...
Link: https://lore.kernel.org/r/20220509172125.313259-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This disables the two Soundwire controllers as well as rx and tx macros
by default on the SM8250 platform to avoid crashes on devices where
these aren't available.
-----BEGIN PGP SIGNATURE-----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=EwkG
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=gn1C
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-fixes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm ARM64 DT fixes for v5.18
This disables the two Soundwire controllers as well as rx and tx macros
by default on the SM8250 platform to avoid crashes on devices where
these aren't available.
* tag 'qcom-arm64-fixes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: sm8250: don't enable rx/tx macro by default
Link: https://lore.kernel.org/r/20220509152310.306179-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This converts a wide range of Qualcomm-related DeviceTree bindings to
YAML, in order to improve our ability to validate the DeviceTree source.
The RPMh power-domain driver gains support for the modem platform SDX65,
the compute platform SC8280XP and the automotive platform SA8540p. While
LLCC gains support for SC8180X and SC8280XP and gains a
MODULE_DEVICE_TABLE() to make it functional as a module.
It adds a driver for configuring the SSC bus, providing Linux access to
the hardware blocks in the sensor subsystem.
The socinfo driver gets confusion related to MSM8974 Pro sorted out and
adds new ids for SM8540 and SC7280.
The SCM driver gains support for MSM8974.
Add missing of_node_put() in smp2p and smsm drivers.
Stop using iterator after list_for_each_entry() and define static
definitions as such, in the PDR driver.
-----BEGIN PGP SIGNATURE-----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=/Dqp
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=rjVH
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for v5.19
This converts a wide range of Qualcomm-related DeviceTree bindings to
YAML, in order to improve our ability to validate the DeviceTree source.
The RPMh power-domain driver gains support for the modem platform SDX65,
the compute platform SC8280XP and the automotive platform SA8540p. While
LLCC gains support for SC8180X and SC8280XP and gains a
MODULE_DEVICE_TABLE() to make it functional as a module.
It adds a driver for configuring the SSC bus, providing Linux access to
the hardware blocks in the sensor subsystem.
The socinfo driver gets confusion related to MSM8974 Pro sorted out and
adds new ids for SM8540 and SC7280.
The SCM driver gains support for MSM8974.
Add missing of_node_put() in smp2p and smsm drivers.
Stop using iterator after list_for_each_entry() and define static
definitions as such, in the PDR driver.
* tag 'qcom-drivers-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (33 commits)
soc: qcom: pdr: use static for servreg_* variables
soc: qcom: llcc: Add sc8180x and sc8280xp configurations
dt-bindings: arm: msm: Add sc8180x and sc8280xp LLCC compatibles
soc: qcom: rpmhpd: add sc8280xp & sa8540p rpmh power-domains
soc: qcom: rpmhpd: Don't warn about sparse rpmhpd arrays
dt-bindings: power: rpmpd: Add sc8280xp RPMh power-domains
spi: dt-bindings: qcom,spi-geni-qcom: convert to dtschema
soc: qcom: socinfo: Sort out 8974PRO names
dt-bindings: soc: qcom,smp2p: convert to dtschema
dt-bindings: qcom: geni-se: Update UART schema reference
dt-bindings: qcom: geni-se: Update I2C schema reference
dt-bindings: soc: qcom,rpmh-rsc: convert to dtschema
bus: add driver for initializing the SSC bus on (some) qcom SoCs
dt-bindings: bus: add device tree bindings for qcom,ssc-block-bus
dt-bindings: qcom: qcom,geni-se: refer to dtschema for SPI
dt-bindings: soc: qcom,smd: convert to dtschema
firmware: qcom_scm: Add compatible for MSM8976 SoC
dt-bindings: firmware: qcom-scm: Document msm8976 bindings
soc: qcom: smem: validate fields of shared structures
soc: qcom: smem: map only partitions used by local HOST
...
Link: https://lore.kernel.org/r/20220509181839.316655-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
Hi,
The current IPC client infrastructure can only be used with IPC3.
This series carries updates for the core side of the client support to handle
IPC4 messages and updates the ipc message injector to be usable with IPC4.
The IPC flood test is only supported by SOF_IPC (IPC3), we are not going to
create the aux device for it at all if the firmware is using IPC4.
Regards,
Peter
---
Peter Ujfalusi (8):
ASoC: SOF: sof-client: Add API to get the maximum IPC payload size
ASoC: SOF: ipc-msg-injector: Query the maximum IPC payload size
ASoC: SOF: sof-client-probes: Query the maximum IPC payload size
ASoC: SOF: sof-client: Add API to get the ipc_type
ASoC: SOF: sof-client: Add support IPC4 message sending
ASoC: SOF: ipc-msg-injector: Separate the message sending
ASoC: SOF: ipc-msg-injector: Add support for IPC4 messages
ASoC: SOF: sof-client: IPC flood test can only work with SOF_IPC
sound/soc/sof/sof-client-ipc-msg-injector.c | 181 ++++++++++++++++++--
sound/soc/sof/sof-client-probes.c | 5 +-
sound/soc/sof/sof-client.c | 66 ++++++-
sound/soc/sof/sof-client.h | 2 +
4 files changed, 227 insertions(+), 27 deletions(-)
--
2.36.0
- A series from Lucas and Paul to update GPCv2 driver for i.MX8MP power
domains, and add HSIO and HDMI block control support.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmJ3IvYUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM6lhwf7BpYDyiaYHBKQLXWWDZj1QanO6bjM
fMlxvVdggfeLW6ijerCb+wf2jNQY75lWRRny4x4WWP+sSVZ4u9SUJlxLrwo/aWYr
44KWWr4PkSMDm5j2bQyy8S9o01ZpxT/FOqqTC51PwgMx7yxB7+d1Z1txWwp5W0jB
Ps92O4bKRfvCCF7Mgjw3/FDu5iek6+9pHx5dQxQ1CWPuvVJos6M9Ktkv27x3oOvI
S4v6Y7v5m1WxSjUK2p09pIGP9AJrHhmRNJF3R/ZrXqUKAlpCQFK6DwZ9mY/rfcfj
tPoqCwj9/UmzG+GlBo8z7I2GQmF7vmwH6bqjP/T6SHOoxE9/fiqT2Swc5A==
=S4x7
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=2GwC
-----END PGP SIGNATURE-----
Merge tag 'imx-drivers-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX drivers update for 5.19:
- A series from Lucas and Paul to update GPCv2 driver for i.MX8MP power
domains, and add HSIO and HDMI block control support.
* tag 'imx-drivers-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: fix semicolon.cocci warnings
soc: imx: add i.MX8MP HDMI blk-ctrl
soc: imx: imx8m-blk-ctrl: Add i.MX8MP media blk-ctrl
soc: imx: add i.MX8MP HSIO blk-ctrl
dt-bindings: power: imx8mp: add defines for HDMI blk-ctrl domains
dt-bindings: soc: Add i.MX8MP media block control DT bindings
soc: imx: imx8m-blk-ctrl: set power device name
soc: imx: gpcv2: add support for i.MX8MP power domains
soc: imx: gpcv2: add PGC control register indirection
Link: https://lore.kernel.org/r/20220508033843.2773685-2-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* wkup_m3: io isolation, voltage scaling, vtt regulator and a debug option to stop m3 in suspend.
* tisci: support for polled mode for system suspend, reset driver is now enabled for COMPILE_TEST
* knav, dma.. misc cleanups for IS_ERR, pm_run_time*, and various other fixups.
-----BEGIN PGP SIGNATURE-----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=Nlpv
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=7h5b
-----END PGP SIGNATURE-----
Merge tag 'ti-driver-soc-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into arm/drivers
TI Driver updates for v5.19
* wkup_m3: io isolation, voltage scaling, vtt regulator and a debug option to stop m3 in suspend.
* tisci: support for polled mode for system suspend, reset driver is now enabled for COMPILE_TEST
* knav, dma.. misc cleanups for IS_ERR, pm_run_time*, and various other fixups.
* tag 'ti-driver-soc-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
soc: ti: wkup_m3_ipc: Add debug option to halt m3 in suspend
soc: ti: wkup_m3_ipc: Add support for i2c voltage scaling
soc: ti: wkup_m3_ipc: Add support for IO Isolation
soc: ti: knav_qmss_queue: Use IS_ERR instead of IS_ERR_OR_NULL when checking knav_queue_open() result
soc: ti: pm33xx: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
firmware: ti_sci: Switch transport to polled mode during system suspend
soc: ti: wkup_m3_ipc: Add support for toggling VTT regulator
soc: ti: knav_qmss_queue: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
soc: ti: knav_dma: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
reset: ti-sci: Allow building under COMPILE_TEST
soc: ti: ti_sci_pm_domains: Check for null return of devm_kcalloc
soc: ti: omap_prm: Use of_device_get_match_data()
soc: ti: pruss: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
soc: ti: replace usage of found with dedicated list iterator variable
soc: ti: wkup_m3_ipc: fix platform_get_irq.cocci warning
Link: https://lore.kernel.org/r/20220507163424.pvqnwrxpoo73lmp2@debtless
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This enables the Qualcomm random number generator and hardware crypto
drivers, as well as DebugFS support, in the qcom defconfig.
-----BEGIN PGP SIGNATURE-----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=/s3v
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=E9Ka
-----END PGP SIGNATURE-----
Merge tag 'qcom-defconfig-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/defconfig
Qualcomm ARM defconfig updates for v5.19
This enables the Qualcomm random number generator and hardware crypto
drivers, as well as DebugFS support, in the qcom defconfig.
* tag 'qcom-defconfig-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: qcom_defconfig: enable debug fs support
ARM: qcom_defconfig: enable options for Qualcomm random number generator
Link: https://lore.kernel.org/r/20220509182209.317208-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This enables the GPI DMA driver, providing access to I2C and SPI
controllers that are setup for shared ownership. The PCIe Gen2 PHY
provides PCI support on the QCS405 platform, among others. The PMIC
watchdog, concell and ADC5 ThermalMonitor drivers provides housekeeping
services on a range of different platforms.
The Display and Video clock controllers for SM8250 are enabled, as is
the audio RX/TX macros and the WCD9335 audio codec driver.
Lastly the Ath11k driver, used on a variety of modern boards and the
FastRPC driver, which provides an interface for computational offloading
on the Hexagon cores, are enabled.
All drivers, except the SM8250 Display and Video clock controller
drivers are enabled as modules. The two clock controllers provides
power-domains and must be builtin to reduce the risk of probe deferral
happening (and being ignored) after late initcall.
-----BEGIN PGP SIGNATURE-----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=BrN9
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=BAuz
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-defconfig-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/defconfig
Qualcomm ARM64 defconfig updates for v5.19
This enables the GPI DMA driver, providing access to I2C and SPI
controllers that are setup for shared ownership. The PCIe Gen2 PHY
provides PCI support on the QCS405 platform, among others. The PMIC
watchdog, concell and ADC5 ThermalMonitor drivers provides housekeeping
services on a range of different platforms.
The Display and Video clock controllers for SM8250 are enabled, as is
the audio RX/TX macros and the WCD9335 audio codec driver.
Lastly the Ath11k driver, used on a variety of modern boards and the
FastRPC driver, which provides an interface for computational offloading
on the Hexagon cores, are enabled.
All drivers, except the SM8250 Display and Video clock controller
drivers are enabled as modules. The two clock controllers provides
power-domains and must be builtin to reduce the risk of probe deferral
happening (and being ignored) after late initcall.
* tag 'qcom-arm64-defconfig-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: defconfig: Enable Qualcomm GPI DMA Driver
arm64: defconfig: Enable Qualcomm PCIe Gen2 PHY
arm64: defconfig: Enable SM8250 video clock controller
arm64: defconfig: Enable PM8916 watchdog driver
arm64: defconfig: enable ath11k driver
arm64: defconfig: Enable some Qualcomm drivers
arm64: defconfig: reenable SM_DISPCC_8250
arm64: defconfig: enable wcd9335 codec as module
arm64: defconfig: enable Qualcomm RX and TX macro for SM8250 audio
Link: https://lore.kernel.org/r/20220509170158.311962-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Enable the WM8524 codec driver as module in arm64 defconfig for audio
support on imx8mn-evk board.
- Enable the ADC part of the STMPE MFD in imx_v6_v7_defconfig, as the
SoM Apalis/Colibri iMX6 use the ADC of a STMPE 811.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmJ3OOMUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM43JwgAgKOb0UndVfyEOV02LPQoVYiEN0P9
cKbenz/IpXFT0fDYyTezg1BmU7T5KH4dg8R40JZdmeOjhEkpigXs1EEVEeBy9Dws
j7RjV+vL/i4shN4j6dYXsWGxLf3E96eNIqMfy4kRfJygTbg/99sgC/YT29OI1TJO
uyJJHqmBvLcfG4kAoYc3W17PM37JD9T6A3DvDZTn5PRgBd8ywK5ydyrqgKgTG6f9
CD6nIyW396rC26+v0Gzrc/0zgxGjLJznD2iiGxyR8Sa6ILYdyXQEIsK5XOst9/PS
E0EnM3HA3icr1bvUUyztdRBuRlYq/BR73GCAWHSpi55Nfh5bT3dCHrpZwQ==
=kFqE
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=pAvl
-----END PGP SIGNATURE-----
Merge tag 'imx-defconfig-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/defconfig
i.MX defconfig update for 5.19:
- Enable the WM8524 codec driver as module in arm64 defconfig for audio
support on imx8mn-evk board.
- Enable the ADC part of the STMPE MFD in imx_v6_v7_defconfig, as the
SoM Apalis/Colibri iMX6 use the ADC of a STMPE 811.
* tag 'imx-defconfig-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: defconfig: Enable the WM8524 codec driver
ARM: imx_v6_v7_defconfig: Enable the ADC part of the STMPE MFD
Link: https://lore.kernel.org/r/20220508033843.2773685-5-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that filler_t and aops->read_folio() have the same type, we can decide
which one to use at the top of the function, and cache ->read_folio in
the filler parameter.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
