lockdep_assert_held() is better suited to checking locking requirements,
since it won't get confused when someone else holds the lock. This is
also a step towards possibly removing spin_is_locked().
Signed-off-by: Lance Roy <ldr709@gmail.com>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <linux-wireless@vger.kernel.org>
Cc: <netdev@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now with wlcore using PM runtime, we can also add support for Linux
generic wakeirq handling for it if configured in the dts file.
The wakeirq can be configured as the second interrupt in the dts file
with interrupts-extended property where it is the padconf irq of the OOB
GPIO pin used for wlcore interrupt.
Note that eventually we should also allow configuring wlcore to use the
SDIO dat1 IRQ for wake-up, and in that case the the wakeirq should be
configured to be the padconf interrupt of the dat1 pin and not the
padconf interrupt of the OOB GPIO pin.
Cc: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We do not currently clear wl->elp_compl on ELP timeout and we have bogus
lingering pointer that wlcore_irq then will try to access after recovery
is done:
BUG: spinlock bad magic on CPU#1, irq/255-wl12xx/580
...
(spin_dump) from [<c01b9344>] (do_raw_spin_lock+0xc8/0x124)
(do_raw_spin_lock) from [<c09b3970>] (_raw_spin_lock_irqsave+0x68/0x74)
(_raw_spin_lock_irqsave) from [<c01a02f0>] (complete+0x24/0x58)
(complete) from [<bf572610>] (wlcore_irq+0x48/0x17c [wlcore])
(wlcore_irq [wlcore]) from [<c01c5efc>] (irq_thread_fn+0x2c/0x64)
(irq_thread_fn) from [<c01c623c>] (irq_thread+0x148/0x290)
(irq_thread) from [<c016b4b0>] (kthread+0x160/0x17c)
(kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
...
After that the system will hang. Let's fix this by adding a flag for
recovery and moving the recovery work call to to the error handling
section.
And we want to set WL1271_FLAG_INTENDED_FW_RECOVERY and actually clear
it too in wl1271_recovery_work() and just downgrade the error to a
warning to prevent overly verbose output.
Cc: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following:
bool efuse_re_pg_sec1flag;
u8 efuse_re_pg_data[8];
are not referenced anywhere in the rtlwifi code.
This patch is originally created by Rick Veens <rickveens92@gmail.com>,
and Joe Perches <joe@perches.com> reminded to apply it to rtlwifi.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver sends an action frame down and waits for a completion signal
triggered by the received BRCMF_E_ACTION_FRAME_OFF_CHAN_COMPLETE event
to continue the process. However, the action frame could be transmitted
either on the current channel or on an off channel. For the on-channel
case, only BRCMF_E_ACTION_FRAME_COMPLETE event will be received when
the frame is transmitted, which make the driver always wait a full
timeout duration. This patch has the completion signal be triggered by
receiving the BRCMF_E_ACTION_FRAME_COMPLETE event for the on-channel
case.
This change fixes WFA p2p certification 5.1.19 failure.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Finding a common channel to send an action frame out is required for
some action types. Since a loop with several scan retry is used to find
the channel, a short wait time could be considered for each attempt.
This patch reduces the wait time from 1500 to 450 msec for each action
frame scan.
This patch fixes the WFA p2p certification 5.1.20 failure caused by the
long action frame send time.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
By using devm functions we can make the code cleaner.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
We should only iomap the area of the chip that is memory mapped.
Otherwise we could be mapping devices beyond the memory space or that
belong to other devices.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Fixes: ebd71e3a48 ("mtd: maps: gpio-addr-flash: fix warnings and make more portable")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
When booting with "nosmt=force" a message is issued into dmesg to
confirm that SMT has been force-disabled but such a message is not
issued when only "nosmt" is on the kernel command line.
Fix that.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20181004172227.10094-1-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Boris Ostrovsky reported a memory leak with device passthrough when SME
is active.
The VFIO driver uses iommu_iova_to_phys() to get the physical address for
an iova. This physical address is later passed into vfio_unmap_unpin() to
unpin the memory. The vfio_unmap_unpin() uses pfn_valid() before unpinning
the memory. The pfn_valid() check was failing because encryption mask was
part of the physical address returned. This resulted in the memory not
being unpinned and therefore leaked after the guest terminates.
The memory encryption mask must be cleared from the physical address in
iommu_iova_to_phys().
Fixes: 2543a786aa ("iommu/amd: Allow the AMD IOMMU to work with memory encryption")
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: <iommu@lists.linux-foundation.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: kvm@vger.kernel.org
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
During probe, if there was an error the memory region and the memory
map were not properly released.This can lead a system unusable if
deferred probe is in use.
Replace mem_request and map with devm_ioremap_resource
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Adds several vendor specific mixer quirks for RME's Class Compliant
USB devices. These provide extra status information from the device
otherwise not available.
These include AES/SPDIF rate and status information, current system
sampling rate and measured frequency. This information is especially
useful in cases where device's clock is slaved to external clock
source.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After reading do_hres() and do_course() and scratching my head a
bit, I figured out why the arithmetic is strange. Document it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/f66f53d81150bbad47d7b282c9207a71a3ce1c16.1538689401.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When a vDSO clock function falls back to the syscall, no special
barriers or ordering is needed, and the syscall fallbacks don't
clobber any memory that is not explicitly listed in the asm
constraints. Remove the "memory" clobber.
This causes minor changes to the generated code, but otherwise has
no obvious performance impact. I think it's nice to have, though,
since it may help the optimizer in the future.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/3a7438f5fb2422ed881683d2ccffd7f987b2dc44.1538689401.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When connecting SFP PHY to phylink use the detected interface.
Otherwise, the link fails to come up when the configured 'phy-mode'
differs from the SFP detected mode.
Move most of phylink_connect_phy() into __phylink_connect_phy(), and
leave phylink_connect_phy() as a wrapper. phylink_sfp_connect_phy() can
now pass the SFP detected PHY interface to __phylink_connect_phy().
This fixes 1GB SFP module link up on eth3 of the Macchiatobin board that
is configured in the DT to "2500base-x" phy-mode.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to unlock the kvm->lock mutex in the error case.
Reported-by: smatch
Fixes: 37940fb0b6 ("KVM: s390: device attrs to enable/disable AP interpretation")
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
the be2net implementation of .ndo_tunnel_{add,del}() changes the value of
NETIF_F_GSO_UDP_TUNNEL bit in 'features' and 'hw_features', but it forgets
to call netdev_features_change(). Moreover, ethtool setting for that bit
can potentially be reverted after a tunnel is added or removed.
GSO already does software segmentation when 'hw_enc_features' is 0, even
if VXLAN offload is turned on. In addition, commit 096de2f83e ("benet:
stricter vxlan offloading check in be_features_check") avoids hardware
segmentation of non-VXLAN tunneled packets, or VXLAN packets having wrong
destination port. So, it's safe to avoid flipping the above feature on
addition/deletion of VXLAN tunnels.
Fixes: 630f4b7056 ("be2net: Export tunnel offloads only when a VxLAN tunnel is created")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net2280 UDC driver invokes the gadget driver's ->disconnect()
callback routine when the net2280_pullup() routine turns off the D+
pullup. This is now unnecessary, because the gadget core performs the
callback on our behalf. This patch removes the unneeded callback.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The bug would let the usb controller enter partial power down,
which was formally known as hibernate, upon boot if nothing was plugged
in to the port. Partial power down couldn't be exited properly, so any
usb devices plugged in after boot would not be usable.
Before the name change, params.hibernation was false by default, so
_dwc2_hcd_suspend() would skip entering hibernation. With the
rename, _dwc2_hcd_suspend() was changed to use params.power_down
to decide whether or not to enter partial power down.
Since params.power_down is non-zero by default, it needs to be set
to 0 for rockchip devices to restore functionality.
This bug was reported in the linux-usb thread:
REGRESSION: usb: dwc2: USB device not seen after boot
The commit that caused this regression is:
6d23ee9caa
Signed-off-by: SolidHal <hal@halemmerich.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since r8a77990 (R-Car E3) doesn't have VBUS detect pin and
number of ramif is 4, this patch adds a new renesas_usb3_priv
variable for the SoC.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
One patch here, fixing a potential host crash introduced (or at least
exacerbated) by a previous fix for corruption relating to radix guest
page faults and THP operations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJbtq7FAAoJEJ2a6ncsY3Gf0PAIAJvq2veNJs0HHsonuI592mK0
YMKL7IproGHBnIuVvpaI3o6iERjMtRaolh+G4dlk3xoQ/TXYzTdimT1cwF2jZblL
wQSsit5499UrJdPsFxBc7lc8yXwRR9+N/ooRAQS/TyK6w00Y+Aep7sTQpRdVCb1G
nskLWXBDWtdB6nGAX9dECpRQP+/voxEJkMMrsFM3rYbBkM/rOqu/IXsCoH2u2jGM
6zFDe7Z35VP77UaehK9W4fGHVc+92oD5E2kN56DNIotYaAT7fudPmNQF+g1GsVFc
Mv8AJdXiQIhZFbpRWTS/UTvyb/aq1Ou6Xd5msTYTMG8v+g0M9h8ZSH3FQCX8RMs=
=Fdit
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-4.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into kvm-master
Third set of PPC KVM fixes for 4.19
One patch here, fixing a potential host crash introduced (or at least
exacerbated) by a previous fix for corruption relating to radix guest
page faults and THP operations.
In commit ec3ed293e7 ("net_sched: change tcf_del_walker() to take idrinfo->lock")
we move fl_hw_destroy_tmplt() to a workqueue to avoid blocking
with the spinlock held. Unfortunately, this causes a lot of
troubles here:
1. tcf_chain_destroy() could be called right after we queue the work
but before the work runs. This is a use-after-free.
2. The chain refcnt is already 0, we can't even just hold it again.
We can check refcnt==1 but it is ugly.
3. The chain with refcnt 0 is still visible in its block, which means
it could be still found and used!
4. The block has a refcnt too, we can't hold it without introducing a
proper API either.
We can make it working but the end result is ugly. Instead of wasting
time on reviewing it, let's just convert the troubling spinlock to
a mutex, which allows us to use non-atomic allocations too.
Fixes: ec3ed293e7 ("net_sched: change tcf_del_walker() to take idrinfo->lock")
Reported-by: Ido Schimmel <idosch@idosch.org>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Magnus Karlsson says:
====================
Previously, the xsk code did not record which umem was bound to a
specific queue id. This was not required if all drivers were zero-copy
enabled as this had to be recorded in the driver anyway. So if a user
tried to bind two umems to the same queue, the driver would say
no. But if copy-mode was first enabled and then zero-copy mode (or the
reverse order), we mistakenly enabled both of them on the same umem
leading to buggy behavior. The main culprit for this is that we did
not store the association of umem to queue id in the copy case and
only relied on the driver reporting this. As this relation was not
stored in the driver for copy mode (it does not rely on the AF_XDP
NDOs), this obviously could not work.
This patch fixes the problem by always recording the umem to queue id
relationship in the netdev_queue and netdev_rx_queue structs. This way
we always know what kind of umem has been bound to a queue id and can
act appropriately at bind time. To make the bind semantics consistent
with ethtool queue manipulations and to facilitate the implementation
of drivers, we also forbid decreasing the number of queues/channels
with ethtool if there is an active AF_XDP socket in the set of queues
that are disabled.
Jakub, please take a look at your patches. The last one I had to
change slightly to make it fit with the new interface
xdp_get_umem_from_qid(). An added bonus with this function is that we,
in the future, can also use it from the driver to get a umem, thus
simplifying driver implementations (and later remove the umem from the
NDO completely). Björn will mail patches, at a later point in time,
using this in the i40e and ixgbe drivers, that removes a good chunk of
code from the ZC implementations. I also made your code aware of Tx
queues. If we create a socket that only has a Tx queue, then the queue
id will refer to a Tx queue id only and could be larger than the
available amount of Rx queues. Please take a look at it.
Differences against v1:
* Included patches from Jakub that forbids decreasing the number of active
queues if a queue to be deactivated has an AF_XDP socket. These have
been adapted somewhat to the new interfaces in patch 2.
* Removed redundant check against real_num_[rt]x_queue in xsk_bind
* Only need to test against real_num_[rt]x_queues in
xdp_clear_umem_at_qid.
Patch 1: Introduces a umem reference in the netdev_rx_queue and
netdev_queue structs.
Patch 2: Records which queue_id is bound to which umem and make sure
that you cannot bind two different umems to the same queue_id.
Patch 3: Pre patch to ethtool_set_channels.
Patch 4: Forbid decreasing the number of active queues if a deactivated
queue has an AF_XDP socket.
Patch 5: Simplify xdp_clear_umem_at_qid now when ethtool cannot deactivate
the queue id we are running on.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
As we now do not allow ethtool to deactivate the queue id we are
running an AF_XDP socket on, we can simplify the implementation of
xdp_clear_umem_at_qid().
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
We already check the RSS indirection table does not use queues which
would be disabled by channel reconfiguration. Make sure user does not
try to disable queues which have a UMEM and zero-copy AF_XDP socket
installed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
ethtool_set_channels() validates the config against driver's max
settings. It retrieves the current config and stores it in a
variable called max. This was okay when only max settings were
accessed but we will soon want to access current settings as
well, so calling the entire structure max makes the code less
readable.
While at it drop unnecessary parenthesis.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Previously, the xsk code did not record which umem was bound to a
specific queue id. This was not required if all drivers were zero-copy
enabled as this had to be recorded in the driver anyway. So if a user
tried to bind two umems to the same queue, the driver would say
no. But if copy-mode was first enabled and then zero-copy mode (or the
reverse order), we mistakenly enabled both of them on the same umem
leading to buggy behavior. The main culprit for this is that we did
not store the association of umem to queue id in the copy case and
only relied on the driver reporting this. As this relation was not
stored in the driver for copy mode (it does not rely on the AF_XDP
NDOs), this obviously could not work.
This patch fixes the problem by always recording the umem to queue id
relationship in the netdev_queue and netdev_rx_queue structs. This way
we always know what kind of umem has been bound to a queue id and can
act appropriately at bind time.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
These references to the umem will be used to store information
on what kind of AF_XDP umem that is bound to a queue id, if any.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Move the attribute parsing from neigh_dump_table to neigh_dump_info, and
pass the filter arguments down to neigh_dump_table in a new struct. Add
the filter option to proxy neigh dumps as well to make them consistent.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Queue deletion is done asynchronous when the last reference on the queue
is dropped. Thus, in order to make sure we don't over allocate under a
connect/disconnect storm, we let queue deletion complete before making
forward progress.
However, given that we flush the system_wq from rdma_cm context which
runs from a workqueue context, we can have a circular locking complaint
[1]. Fix that by using a private workqueue for queue deletion.
[1]:
======================================================
WARNING: possible circular locking dependency detected
4.19.0-rc4-dbg+ #3 Not tainted
------------------------------------------------------
kworker/5:0/39 is trying to acquire lock:
00000000a10b6db9 (&id_priv->handler_mutex){+.+.}, at: rdma_destroy_id+0x6f/0x440 [rdma_cm]
but task is already holding lock:
00000000331b4e2c ((work_completion)(&queue->release_work)){+.+.}, at: process_one_work+0x3ed/0xa20
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 ((work_completion)(&queue->release_work)){+.+.}:
process_one_work+0x474/0xa20
worker_thread+0x63/0x5a0
kthread+0x1cf/0x1f0
ret_from_fork+0x24/0x30
-> #2 ((wq_completion)"events"){+.+.}:
flush_workqueue+0xf3/0x970
nvmet_rdma_cm_handler+0x133d/0x1734 [nvmet_rdma]
cma_ib_req_handler+0x72f/0xf90 [rdma_cm]
cm_process_work+0x2e/0x110 [ib_cm]
cm_req_handler+0x135b/0x1c30 [ib_cm]
cm_work_handler+0x2b7/0x38cd [ib_cm]
process_one_work+0x4ae/0xa20
nvmet_rdma:nvmet_rdma_cm_handler: nvmet_rdma: disconnected (10): status 0 id 0000000040357082
worker_thread+0x63/0x5a0
kthread+0x1cf/0x1f0
ret_from_fork+0x24/0x30
nvme nvme0: Reconnecting in 10 seconds...
-> #1 (&id_priv->handler_mutex/1){+.+.}:
__mutex_lock+0xfe/0xbe0
mutex_lock_nested+0x1b/0x20
cma_ib_req_handler+0x6aa/0xf90 [rdma_cm]
cm_process_work+0x2e/0x110 [ib_cm]
cm_req_handler+0x135b/0x1c30 [ib_cm]
cm_work_handler+0x2b7/0x38cd [ib_cm]
process_one_work+0x4ae/0xa20
worker_thread+0x63/0x5a0
kthread+0x1cf/0x1f0
ret_from_fork+0x24/0x30
-> #0 (&id_priv->handler_mutex){+.+.}:
lock_acquire+0xc5/0x200
__mutex_lock+0xfe/0xbe0
mutex_lock_nested+0x1b/0x20
rdma_destroy_id+0x6f/0x440 [rdma_cm]
nvmet_rdma_release_queue_work+0x8e/0x1b0 [nvmet_rdma]
process_one_work+0x4ae/0xa20
worker_thread+0x63/0x5a0
kthread+0x1cf/0x1f0
ret_from_fork+0x24/0x30
Fixes: 777dc82395 ("nvmet-rdma: occasionally flush ongoing controller teardown")
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
It appears that in commit 9d7a224b46 ("dma-direct: always allow dma mask
<= physiscal memory size") the logic of the test was changed from a "<" to
a ">=" however I don't see any reason for that change. I am assuming that
there was some additional change planned, specifically I suspect the logic
was intended to be reversed and possibly used for a return. Since that is
the case I have gone ahead and done that.
This addresses issues I had on my system that prevented me from booting
with the above mentioned commit applied on an x86_64 system w/ Intel IOMMU.
Fixes: 9d7a224b46 ("dma-direct: always allow dma mask <= physiscal memory size")
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/serial/cypress_m8.c: In function 'cypress_set_termios':
drivers/usb/serial/cypress_m8.c:866:18: warning:
variable 'iflag' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix interrupt-out transfer length which was being set to the
transfer-buffer length rather than the size of the outgoing packet.
Note that no slab data was leaked as the whole transfer buffer is always
cleared before each transfer.
Fixes: 9aa8dae7b1 ("cypress_m8: use usb_fill_int_urb where appropriate")
Signed-off-by: Johan Hovold <johan@kernel.org>
Enable support for cbus gpios on FT232R. The cbus configuration is
stored in one word in the EEPROM at offset 0x0a (byte-offset 0x14) with
the mux config for CBUS0, CBUS1, CBUS2 and CBUS3 in bits 0..3, 4..7,
8..11 and 12..15, respectively.
Tested using FT232RL by configuring one cbus pin at a time.
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the gpio line names, which cause gpiolib to complain loudly
whenever a second ftdi gpiochip is registered:
gpio gpiochip5: Detected name collision for GPIO name 'CBUS0'
gpio gpiochip5: Detected name collision for GPIO name 'CBUS1'
gpio gpiochip5: Detected name collision for GPIO name 'CBUS2'
gpio gpiochip5: Detected name collision for GPIO name 'CBUS3'
and also prevents the legacy sysfs interface from being used (as the
line names are used as device names whenever they are set):
sysfs: cannot create duplicate filename '/class/gpio/CBUS0'
Until non-unique names are supported by gpiolib (without warnings and
stack dumps), let's leave the gpio lines unnamed.
Signed-off-by: Johan Hovold <johan@kernel.org>
While we currently grab a runtime PM ref in nouveau's normal connector
detection code, we apparently don't do this for MST. This means if we're
in a scenario where the GPU is suspended and userspace attempts to do a
connector probe on an MSTC connector, the probe will fail entirely due
to the DP aux channel and GPU not being woken up:
[ 316.633489] nouveau 0000:01:00.0: i2c: aux 000a: begin idle timeout ffffffff
[ 316.635713] nouveau 0000:01:00.0: i2c: aux 000a: begin idle timeout ffffffff
[ 316.637785] nouveau 0000:01:00.0: i2c: aux 000a: begin idle timeout ffffffff
...
So, grab a runtime PM ref here.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This adds a mode where the vcore scheduling logic in HV KVM limits itself
to scheduling only virtual cores from the same VM on any given physical
core. This is enabled via a new module parameter on the kvm-hv module
called "one_vm_per_core". For this to work on POWER9, it is necessary to
set indep_threads_mode=N. (On POWER8, hardware limitations mean that KVM
is never in independent threads mode, regardless of the indep_threads_mode
setting.)
Thus the settings needed for this to work are:
1. The host is in SMT1 mode.
2. On POWER8, the host is not in 2-way or 4-way static split-core mode.
3. On POWER9, the indep_threads_mode parameter is N.
4. The one_vm_per_core parameter is Y.
With these settings, KVM can run up to 4 vcpus on a core at the same
time on POWER9, or up to 8 vcpus on POWER8 (depending on the guest
threading mode), and will ensure that all of the vcpus belong to the
same VM.
This is intended for use in security-conscious settings where users are
concerned about possible side-channel attacks between threads which could
perhaps enable one VM to attack another VM on the same core, or the host.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When an OS (currently only classic Mac OS) is running in KVM-PR and makes a
linked jump from code with split hack addressing enabled into code that does
not, LR is not correctly updated and reflects the previously munged PC.
To fix this, this patch undoes the address munge when exiting split
hack mode so that code relying on LR being a proper address will now
execute. This does not affect OS X or other operating systems running
on KVM-PR.
Signed-off-by: Cameron Kaiser <spectre@floodgap.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When we use raw socket as the vhost backend, a packet from virito with
gso offloading information, cannot be sent out in later validaton at
xmit path, as we did not set correct skb->protocol which is further used
for looking up the gso function.
To fix this, we set this field according to virito hdr information.
Fixes: e858fae2b0 ("virtio_net: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Jianfeng Tan <jianfeng.tan@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: Consolidate metrics handling for ipv4 and ipv6
As part of the IPv6 fib info refactoring, the intent was to make metrics
handling for ipv6 identical to ipv4. One oversight in ip6_dst_destroy
led to confusion and a couple of incomplete attempts at finding and
fixing the resulting memory leak which was ultimately resolved by
ce7ea4af08 ("ipv6: fix memory leak on dst->_metrics").
Refactor metrics hanlding make the code really identical for v4 and v6,
and add a few test cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ipv4 and ipv6 test cases for metrics (mtu) when fib entries are
created. Can be used with kmemleak to see leaks with both fib entries
and dst_entry.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the refcounting and potential free of dst metrics associated
for ipv4 and ipv6 to a common helper.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4 and ipv6 both use refcounted metrics if FIB entries have metrics set.
Move the common initialization code to a helper and use for both protocols.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the refcounting and potential free of dst metrics associated
with a fib entry to a helper and use it in both ipv4 and ipv6.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate initialization of ipv4 and ipv6 metrics when fib entries
are created into a single helper, ip_fib_metrics_init, that handles
the call to ip_metrics_convert.
If no metrics are defined for the fib entry, then the metrics is set
to dst_default_metrics.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c499696e79 ("net: dsa: b53: Stop using dev->cpu_port
incorrectly") was a bit too trigger happy in removing the CPU port from
the VLAN membership because we rely on DSA to program the CPU port VLAN,
which it does, except it does not bother itself with tagged/untagged and
just usese untagged.
Having the CPU port "follow" the user ports tagged/untagged is not great
and does not allow for properly differentiating, so keep the CPU port
tagged in all VLANs.
Reported-by: Gerhard Wiesinger <lists@wiesinger.com>
Fixes: c499696e79 ("net: dsa: b53: Stop using dev->cpu_port incorrectly")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load the respective NAT helper module if the flow uses it.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
