Add device-tree bindings documentation file for ADAU1977 audio codec.
This describes device-tree fields that are already supported by the driver.
The driver supports both I2C AND and SPI, and this doc covers both aspects
of the DT configuration.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are platforms which don't provide input clock rate but provide
I2C timing parameters. Commit 3bd4f27727 ("i2c: designware: Call
i2c_dw_clk_rate() only once in i2c_dw_init_master()") causes needless
warning during probe on those platforms since i2c_dw_clk_rate(), which
causes the warning when input clock is unknown, is called even when
there is no need to calculate timing parameters.
Fixes: 3bd4f27727 ("i2c: designware: Call i2c_dw_clk_rate() only once in i2c_dw_init_master()")
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # 4.19
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, replace with the standard "fall through" annotation.
gcc can't understand the mixed texts, unfortunately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, add the "fall through" annotation in Intel SST
skylake driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, add the "fall through" annotations in rt274 driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, replace with the standard "fall through" annotation.
Unfortunately gcc doesn't understand the mixed comment lines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, replace with the standard "fall through" annotation
at the right place. It has to be put right before the next label.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We replace the vfio_ap_mdev_copy_masks() by the new
kvm_arch_crypto_set_masks() to be able to use the standard
KVM tracing system.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Message-Id: <1538728270-10340-3-git-send-email-pmorel@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
kvm_arch_crypto_set_masks is a new function to centralize
the setup the APCB masks inside the CRYCB SIE satellite.
To trace APCB mask changes, we add KVM_EVENT() tracing to
both kvm_arch_crypto_set_masks and kvm_arch_crypto_clear_masks.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Message-Id: <1538728270-10340-2-git-send-email-pmorel@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Current implementation of dump_station cfg80211 callback supports
AP mode only. Add support for STA mode as well: by default in STA
mode this callback is supposed to return AP on managed interface.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Command responses and events from the firmware are copied twice in
control path: at first in shm core (qtnf_shm_handle_new_data) and
then in pcie bus drivers (qtnf_pcie_control_rx_callback). There
is no need to copy this data twice, it can be done only once
in rx callbacks.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware supports scan dwell time tuning for various types of scans.
Enable support for this feature:
- advertise capability to configure channel dwell time to host
- pass scan dwell parameters to wireless card in scan request
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Notify firmware to flush cache before scanning when needed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On disconnect wireless core attempts to remove all the supported keys.
Following cfg80211_ops conventions, firmware returns -ENOENT code
for the out-of-bound key indexes. This is a normal behavior,
so no need to report errors for this case.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver retrieves information about supported extended capabilities
from wireless card. However this information is not propagated
further to Linux wireless core. Fix this by setting extended
capabilities fields of wiphy structure.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SGI should be passed to wireless core as a part of rate structure.
Otherwise wireless core performs incorrect rate calculation when
SGI is enabled in hardware but not reported to host.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not cancel scan in disconnect callback. If there is an active scan,
it will be cancelled by firmware, then host driver will be properly
notified by event.
Cancelling scan in disconnect callback occasionally may lead to the
following race issue. Host is able to queue one scan after scan
abort in disconnect callback, and another scan after scan abort
in event handler. As a result, firmware receives second scan
before the first scan completes.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unify command error handling using qtnf_cmd_resp_result_decode
function. Do not duplicate error messages in command handlers
and cfg80211 callbacks: report 'cmd exec fail' only on control
path internal failure. Remove redundant 'unlikely' macros.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Several members of pwr-MAC structure are re-initialized several times
together with per-VIF initialization. Fix that and simplify the code.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case firmware reports that it can not do OBSS scanning for 40MHz
2.4GHz channels itself, tell userpsace to do that instead by setting
NL80211_FEATURE_NEED_OBSS_SCAN flag.
Signed-off-by: Igor mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When cfg80211 disconnect callback is triggered and command is
processed by firmware, disconnect event with local parameter
set must be sent immediately. Indicating that it's a "local"
event (not from AP) will help upper layers to process this
event correctly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove STA connection states tracking from driver.
Leave it wireless core on host and to firmware.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the root complex suspends it must send a PME_Turn_Off TLP.
Implement this by asserting the "turnoff" reset.
On imx7d this functionality is part of the System Reset Controller (SRC)
and is exposed through the linux reset-controller subsystem.
On imx6 equivalent bits are in the IOMUXC pinmux controller General
Purpose Register (GPR) area which the imx6-pcie driver accesses
directly.
This is only for imx7d right now but it's deliberately implemented as an
optional reset, ignoring the chip variant:
* Older dtbs won't have this reset so it will be ignored.
* Future chips might also expose this as a reset controller.
For example imx8m (not yet supported) has the exact same
PCIE_CTRL_APPS_TURNOFF bit in the same location.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
"bellow" -> "below"
The recommendation from kegel.com/kerspell is to only fix the howlers.
"Bellow" is a synonym of "howl" so this should be appropriate.
Signed-off-by: Kyrylo Tkachov <kyrylo.tkachov@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Functionality of the xen-tpmfront driver was lost secondary to
the introduction of xenbus multi-page support in commit ccc9d90a9a
("xenbus_client: Extend interface to support multi-page ring").
In this commit pointer to location of where the shared page address
is stored was being passed to the xenbus_grant_ring() function rather
then the address of the shared page itself. This resulted in a situation
where the driver would attach to the vtpm-stubdom but any attempt
to send a command to the stub domain would timeout.
A diagnostic finding for this regression is the following error
message being generated when the xen-tpmfront driver probes for a
device:
<3>vtpm vtpm-0: tpm_transmit: tpm_send: error -62
<3>vtpm vtpm-0: A TPM error (-62) occurred attempting to determine
the timeouts
This fix is relevant to all kernels from 4.1 forward which is the
release in which multi-page xenbus support was introduced.
Daniel De Graaf formulated the fix by code inspection after the
regression point was located.
Fixes: ccc9d90a9a ("xenbus_client: Extend interface to support multi-page ring")
Signed-off-by: Dr. Greg Wettstein <greg@enjellic.com>
[boris: Updated commit message, added Fixes tag]
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Currently the TPM driver only supports blocking calls, which doesn't allow
asynchronous IO operations to the TPM hardware.
This patch changes it and adds support for nonblocking write and a new poll
function to enable applications, which want to take advantage of this.
Tested-by: Philip Tricca <philip.b.tricca@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off--by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Add a ptr to struct tpm_space to the file_priv and consolidate
of the write operations for the two interfaces.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Tested-by: Philip Tricca <philip.b.tricca@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off--by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
While having SECURITYFS enabled for the tpm subsystem is beneficial in
most cases, it is not strictly necessary to have it enabled at all.
Especially on platforms without any boot firmware integration of the TPM
(e.g. raspberry pi) it does not add any value for the tpm subsystem,
as there is no eventlog present.
By turning it from 'select' to 'imply' it still gets selected per
default, but enables users who want to save some kb of ram by turning
SECURITYFS off.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
For TPM 1.2 chips the system setup utility allows to set the TPM device in
one of the following states:
* Active: Security chip is functional
* Inactive: Security chip is visible, but is not functional
* Disabled: Security chip is hidden and is not functional
When choosing the "Inactive" state, the TPM 1.2 device is enumerated and
registered, but sending TPM commands fail with either TPM_DEACTIVATED or
TPM_DISABLED depending if the firmware deactivated or disabled the TPM.
Since these TPM 1.2 error codes don't have special treatment, inactivating
the TPM leads to a very noisy kernel log buffer that shows messages like
the following:
tpm_tis 00:05: 1.2 TPM (device-id 0x0, rev-id 78)
tpm tpm0: A TPM error (6) occurred attempting to read a pcr value
tpm tpm0: TPM is disabled/deactivated (0x6)
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting to read a pcr value
ima: No TPM chip found, activating TPM-bypass! (rc=6)
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting get random
Let's just suppress error log messages for the TPM_{DEACTIVATED,DISABLED}
return codes, since this is expected when the TPM 1.2 is set to Inactive.
In that case the kernel log is cleaner and less confusing for users, i.e:
tpm_tis 00:05: 1.2 TPM (device-id 0x0, rev-id 78)
tpm tpm0: TPM is disabled/deactivated (0x6)
ima: No TPM chip found, activating TPM-bypass! (rc=6)
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
When checking whether the response is large enough to be able to contain
the received random bytes in tpm_get_random() and tpm2_get_random(),
they fail to take account the header size, which should be added to the
minimum size. This commit fixes this issue.
Cc: stable@vger.kernel.org
Fixes: c659af78eb ("tpm: Check size of response before accessing data")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
On OLPC XO-1, the RTC is discovered via device tree from the arch
initcall. Don't let the PC platform register another one from its device
initcall, it's not going to work:
sysfs: cannot create duplicate filename '/devices/platform/rtc_cmos'
CPU: 0 PID: 1 Comm: swapper Not tainted 4.19.0-rc6 #12
Hardware name: OLPC XO/XO, BIOS OLPC Ver 1.00.01 06/11/2014
Call Trace:
dump_stack+0x16/0x18
sysfs_warn_dup+0x46/0x58
sysfs_create_dir_ns+0x76/0x9b
kobject_add_internal+0xed/0x209
? __schedule+0x3fa/0x447
kobject_add+0x5b/0x66
device_add+0x298/0x535
? insert_resource_conflict+0x2a/0x3e
platform_device_add+0x14d/0x192
? io_delay_init+0x19/0x19
platform_device_register+0x1c/0x1f
add_rtc_cmos+0x16/0x31
do_one_initcall+0x78/0x14a
? do_early_param+0x75/0x75
kernel_init_freeable+0x152/0x1e0
? rest_init+0xa2/0xa2
kernel_init+0x8/0xd5
ret_from_fork+0x2e/0x38
kobject_add_internal failed for rtc_cmos with -EEXIST, don't try to
register things with the same name in the same directory.
platform rtc_cmos: registered platform RTC device (no PNP device found)
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Ingo Molnar <mingo@redhat.com>
CC: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/20181004160808.307738-1-lkundrak@v3.sk
Sanitize user pointer given to __copy_to_user, both for standard version
and memcopy version of the user accessor.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Introduce C and asm helpers to sanitize user address, taking the
address range they target into account.
Use asm helper for existing sanitization in __copy_from_user().
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
When Spectre mitigation is required, __put_user() needs to include
check_uaccess. This is already the case for put_user(), so just make
__put_user() an alias of put_user().
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
A mispredicted conditional call to set_fs could result in the wrong
addr_limit being forwarded under speculation to a subsequent access_ok
check, potentially forming part of a spectre-v1 attack using uaccess
routines.
This patch prevents this forwarding from taking place, but putting heavy
barriers in set_fs after writing the addr_limit.
Porting commit c2f0ad4fc0 ("arm64: uaccess: Prevent speculative use
of the current addr_limit").
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
With Spectre-v1.1 mitigations, __put_user_error is pointless. In an attempt
to remove it, replace its references in frame setups with __put_user.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Copy events to user using __copy_to_user() rather than copy members of
individually with __put_user_error().
This has the benefit of disabling/enabling PAN once per event intead of
once per event member.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Use __copy_to_user() rather than __put_user_error() for individual
members when saving VFP state.
This has the benefit of disabling/enabling PAN once per copied struct
intead of once per write.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
When setting a dummy iwmmxt context, create a local instance and
use __copy_to_user both cases whether iwmmxt is being used or not.
This has the benefit of disabling/enabling PAN once for the whole copy
intead of once per write.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
When saving the ARM integer registers, use __copy_to_user() to
copy them into user signal frame, rather than __put_user_error().
This has the benefit of disabling/enabling PAN once for the whole copy
intead of once per write.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Before cloning into a file, update the ctime and remove sensitive
attributes like suid, just like we'd do for a regular file write.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
When we're reflinking between two files and the destination file range
is well beyond the destination file's EOF marker, zero any posteof
speculative preallocations in the destination file so that we don't
expose stale disk contents. The previous strategy of trying to clear
the preallocations does not work if the destination file has the
PREALLOC flag set.
Uncovered by shared/010.
Reported-by: Zorro Lang <zlang@redhat.com>
Bugzilla-id: https://bugzilla.kernel.org/show_bug.cgi?id=201259
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Refactor all the reflink preparation steps into a separate helper
that we'll use to land all the upcoming fixes for insufficient input
checks.
This rework also moves the invalidation of the destination range to
the prep function so that it is done before the range is remapped.
This ensures that nobody can access the data in range being remapped
until the remap is complete.
[dgc: fix xfs_reflink_remap_prep() return value and caller check to
handle vfs_clone_file_prep_inodes() returning 0 to mean "nothing to
do". ]
[dgc: make sure length changed by vfs_clone_file_prep_inodes() gets
propagated back to XFS code that does the remapping. ]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
This is required for the imx pci driver to send the PME_Turn_Off TLP.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
This is documented as "required" but won't be present in old dtbs.
These resets are also present on other imx chips but right now only
imx7d implements them through the reset controller subsystem.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
This is required for the imx pci driver to send the PME_Turn_Off TLP.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/b43/main.c: In function 'b43_one_core_detach':
drivers/net/wireless/broadcom/b43/main.c:5496:17: warning:
variable 'wl' set but not used [-Wunused-but-set-variable]
After commit 644aa4d620 ("b43: remove list of IEEE 802.11 devices")
'wl' is not used any more.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace "Fallthough" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Michael Buesch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
