When configure pause, current implementation returns directly
after setup PFC without setup BP, which is not sufficient.
So this patch fixes it, only return while setting PFC failed.
Fixes: 44e59e375b ("net: hns3: do not return GE PFC setting err when initializing")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the hardware does not handle mailboxes and the hardware
reset include TQP reset, so it is unnecessary to reset TQP
in the hclgevf_ae_stop() while doing VF reset. Also it is
unnecessary to reset the remaining TQP when one reset fails.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses a reserved byte in the hclge_mbx_vf_to_pf_cmd
to save the need_resp flag, so when PF received the mailbox,
it can use it to decise whether send a response to VF.
For hclge_set_vf_uc_mac_addr(), it should use mbx_need_resp flag
to decide whether send response to VF.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since irq handler and mailbox task will both update arq's count,
so arq's count should use atomic_t instead of u32, otherwise
its value may go wrong finally.
Fixes: 07a0556a3a ("net: hns3: Changes to support ARQ(Asynchronous Receive Queue)")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HCLGEVF_STATE_CMD_DISABLE is more suitable than
HCLGEVF_STATE_RST_HANDLING to stop sending keep alive msg,
since HCLGEVF_STATE_RST_HANDLING only be set when the reset
task is running.
Fixes: c59a85c07e ("net: hns3: stop sending keep alive msg to PF when VF is resetting")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bdinfo handled in hns3_handle_bdinfo is only valid on the
last BD of the current packet, currently the bd info may be handled
based on the first BD if the packet has more than two BDs, which
may cause rx error.
This patch fixes it by using the last BD of the current packet in
hns3_handle_bdinfo.
Also, hns3_set_rx_skb_rss_type has used RSS hash value from the last
BD of the current packet, so remove the same last BD calculation in
hns3_set_rx_skb_rss_type and call it from hns3_handle_bdinfo.
Fixes: e559709505 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_desc_unused() returns how many BD have been cleaned, but new
buffer has not been attached to them. The register of
HNS3_RING_RX_RING_FBDNUM_REG returns how many BD need allocating new
buffer to or need to cleaned. So the remaining BD need to be clean
is HNS3_RING_RX_RING_FBDNUM_REG - hns3_desc_unused().
Also, new buffer can not attach to the pending BD when the last BD is
not handled, because memcpy has not been done on the first pending BD.
This patch fixes by subtracting the pending BD num from unused_count
after 'HNS3_RING_RX_RING_FBDNUM_REG - unused_count' is used to calculate
the BD bum need to be clean.
Fixes: e559709505 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_clean_tx_ring calls hns3_nic_reclaim_one_desc to clean
buffers and set ring->next_to_clean, then hns3_nic_net_xmit
reuses the cleaned buffers. But there are no memory barriers
when buffers gets recycled, so the recycled buffers can be
corrupted.
This patch uses smp_store_release to update ring->next_to_clean
and smp_load_acquire to read ring->next_to_clean to properly
hand off buffers from hns3_clean_tx_ring to hns3_nic_net_xmit.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device may be shutdown without the hardware being reinitialized, in
which case we want to ensure we cleanup properly.
This is especially important for kexec with traffic flowing.
The shutdown procedures resembles the remove procedures, so we can reuse
those common tasks.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/nfc/st95hf/core.c: In function 'st95hf_irq_thread_handler':
drivers/nfc/st95hf/core.c:786:26: warning:
variable 'nfcddev' set but not used [-Wunused-but-set-variable]
drivers/nfc/st95hf/core.c:784:17: warning:
variable 'dev' set but not used [-Wunused-but-set-variable]
They are never used since introduction in
commit cab47333f0 ("NFC: Add STMicroelectronics ST95HF driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I forgot to remove one rcu_read_unlock() before a return statement.
Joy of mixing goto and return styles in a function :)
Fixes: 4109a2c3b9 ("tipc: tipc_udp_recv() cleanup vs rcu verbs")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY's behave differently when being reset. Some reset registers to
defaults, some don't. Some trigger an autoneg restart, some don't.
So let's also set the autoneg restart bit when resetting. Then PHY
behavior should be more consistent. Clearing BMCR_ISOLATE serves the
same purpose and is borrowed from genphy_restart_aneg.
BMCR holds the speed / duplex settings in fixed mode. Therefore
we may have an issue if a soft reset resets BMCR to its default.
So better call genphy_setup_forced() afterwards in fixed mode.
We've seen no related complaint in the last >10 yrs, so let's
treat it as an improvement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Apple products use the same protocol for tethering over USB.
To simplify the code and make it future proof, use
USB_VENDOR_AND_INTERFACE_INFO() instead of
USB_DEVICE_AND_INTERFACE_INFO() to automatically detect and support
all existing and future Apple products using the same interface.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, refactor code a
bit and mark switch cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/broadcom/cnic.c: In function ‘cnic_cm_process_kcqe’:
drivers/net/ethernet/broadcom/cnic.c:4044:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
opcode = L4_KCQE_OPCODE_VALUE_CLOSE_COMP;
drivers/net/ethernet/broadcom/cnic.c:4050:2: note: here
case L4_KCQE_OPCODE_VALUE_RESET_RECEIVED:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c: In function ‘fwevtq_handler’:
drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c:520:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
cpl = (void *)p;
~~~~^~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c:524:2: note: here
case CPL_SGE_EGR_UPDATE: {
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
In file included from drivers/net/wimax/i2400m/debug-levels.h:30,
from drivers/net/wimax/i2400m/control.c:86:
drivers/net/wimax/i2400m/control.c: In function ‘i2400m_report_tlv_system_state’:
./include/linux/wimax/debug.h:200:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
do { \
^
./include/linux/wimax/debug.h:404:36: note: in expansion of macro ‘_d_printf’
#define d_printf(l, _dev, f, a...) _d_printf(l, "", _dev, f, ## a)
^~~~~~~~~
drivers/net/wimax/i2400m/control.c:354:3: note: in expansion of macro ‘d_printf’
d_printf(1, dev, "entering BS-negotiated idle mode\n");
^~~~~~~~
drivers/net/wimax/i2400m/control.c:355:2: note: here
case I2400M_SS_DISCONNECTING:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
In file included from drivers/net/ethernet/amd/xgbe/xgbe-drv.c:129:
drivers/net/ethernet/amd/xgbe/xgbe-drv.c: In function ‘xgbe_set_hwtstamp_settings’:
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1392:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
(_var) |= (((_val) & ((0x1 << (_width)) - 1)) << (_index)); \
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1419:2: note: in expansion of macro ‘SET_BITS’
SET_BITS((_var), \
^~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1614:3: note: in expansion of macro ‘XGMAC_SET_BITS’
XGMAC_SET_BITS(mac_tscr, MAC_TSCR, TSVER2ENA, 1);
^~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1616:2: note: here
case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
^~~~
In file included from drivers/net/ethernet/amd/xgbe/xgbe-drv.c:129:
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1392:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
(_var) |= (((_val) & ((0x1 << (_width)) - 1)) << (_index)); \
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1419:2: note: in expansion of macro ‘SET_BITS’
SET_BITS((_var), \
^~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1625:3: note: in expansion of macro ‘XGMAC_SET_BITS’
XGMAC_SET_BITS(mac_tscr, MAC_TSCR, TSVER2ENA, 1);
^~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1627:2: note: here
case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
^~~~
In file included from drivers/net/ethernet/amd/xgbe/xgbe-drv.c:129:
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1392:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
(_var) |= (((_val) & ((0x1 << (_width)) - 1)) << (_index)); \
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1419:2: note: in expansion of macro ‘SET_BITS’
SET_BITS((_var), \
^~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1636:3: note: in expansion of macro ‘XGMAC_SET_BITS’
XGMAC_SET_BITS(mac_tscr, MAC_TSCR, TSVER2ENA, 1);
^~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1638:2: note: here
case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comments are modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing break statement in order to prevent the code from falling
through to cases SIOCGSTAMP_NEW and SIOCGSTAMPNS_NEW.
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: 0768e17073 ("net: socket: implement 64-bit timestamps")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: updates 2019-04-25
please apply one more patch series for qeth to net-next. Nothing special,
just a bunch of cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When building the L3 HW header for non-IP packets, trust the cast type
that was passed as parameter. qeth_l3_get_cast_type() has most likely
also used h_dest to determine the cast type, so we get the same
result, and can remove that duplicated code.
In the unlikely case that we would get a _different_ cast type, then
that's based off a route lookup and should be considered authoritative.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This de-duplicates the L2 and L3 cast-type code, and makes the L2 code
a bit more robust by removing the fragile assumption that skb->data
always points to the Ethernet Header. This would break in code paths
where we pushed the HW header onto the skb.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QETH_MAX_BUFFER_ELEMENTS() macro effectively returns a constant
value. To avoid some redundant pointer chasing and computations in the
xmit hot path, cache this value in the queue struct.
Take this as opportunity to shrink some of the queue struct's fields to
their appropriate value range, slightly reducing its total size.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the first initialization of a queue, its Output Buffers are in a
clean state with no attached resources. On every subsequent
initialization, qeth_l?_stop_card() has previously put them in a clean
state via qeth_drain_output_queues(). So the call to
qeth_clear_output_buffer() is redundant and can be removed.
While at it, move the initialization of the queue's card pointer into
the queue allocation. It never changes afterwards.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have helper macros for all possible device types, replace all
remaining open-coded accesses to the type fields.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't keep track of Input Buffer states, so remove the comments that
make it sound like the qeth_qdio_buffer_states enum applies to
Input Buffers.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unclear what exact purpose this seqno may have served in the past.
But it's certainly no longer used anymore, as the following
napi_gro_receive() will straight away clear this part of the cb again.
Suggested-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang produces a harmless warning for each use for the qeth_adp_supported
macro:
drivers/s390/net/qeth_l2_main.c:559:31: warning: implicit conversion from enumeration type 'enum qeth_ipa_setadp_cmd' to
different enumeration type 'enum qeth_ipa_funcs' [-Wenum-conversion]
if (qeth_adp_supported(card, IPA_SETADP_SET_PROMISC_MODE))
~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/s390/net/qeth_core.h:179:41: note: expanded from macro 'qeth_adp_supported'
qeth_is_ipa_supported(&c->options.adp, f)
~~~~~~~~~~~~~~~~~~~~~ ^
Add a version of this macro that uses the correct types, and
remove the unused qeth_adp_enabled() macro that has the same
problem.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
netdevsim: implement proper device model
Currently the model of netdevsim is a bit odd in multiple ways.
1) devlink instance is not in any way related with actual netdevsim
netdevices. Instead, it is created per-namespace.
2) multi-port netdevsim device is done using "link" attribute.
3) netdevsim bus is there only to have something to bind the netdev to,
it really does not act as a bus.
4) netdevsim instances are created by "ip link add" which is great for
soft devices with no hw backend. The rtnl core allocates netdev and
calls into driver holding rtnl mutex. For hw-backed devices, this
flow is wrong as it breaks order in which things are done.
This patchset adjust netdevsim to fix all above.
In order to support proper devlink and devlink port instances and to be
able to emulate real devices, there is need to implement bus probe and
instantiate everything from there. User can specify device id and port
count to be instantianted. For example:
$ echo "10 4" > /sys/bus/netdevsim/new_device
Then devlink shows this:
$ devlink dev
netdevsim/netdevsim10
$ devlink port
netdevsim/netdevsim10/0: type eth netdev eni0np1 flavour physical
netdevsim/netdevsim10/1: type eth netdev eni0np2 flavour physical
netdevsim/netdevsim10/2: type eth netdev eni0np3 flavour physical
netdevsim/netdevsim10/3: type eth netdev eni0np4 flavour physical
There is possible to add and delete ports using their indexes
during netdevsim device lifetime like this:
Then devlink shows this:
$ devlink port
netdevsim/netdevsim10/1: type eth netdev eni10np2 flavour physical
netdevsim/netdevsim10/2: type eth netdev eni10np3 flavour physical
netdevsim/netdevsim10/3: type eth netdev eni10np4 flavour physical
netdevsim/netdevsim10/43: type eth netdev eni10np44 flavour physical
Debugfs topology is also adjusted a bit. The rest stays the same as
before.
Udev bits are merged un systemd upstream git:
eaa9d507d8
See individual patches for changelog.
====================
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ndo_get_devlink_port and allow switch_id and port_name to be
handled by devlink.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the existing way to create netdevsim over rtnetlink and move the
netdev creation/destruction to dev probe, so for every probed port,
a netdevsim-netdev instance is created.
Adjust selftests to work with new interface.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to test flows in core, it is beneficial to maintain previously
supported possibility to add and delete ports during netdevsim lifetime.
Do it by extending device sysfs attrs by "new_port" and "del_port".
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement netdevsim bus probing of netdevsim devices. For every probed
device create a devlink instance. According to the user-passed value,
create a number of ports represented by devlink port instances.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the model where dev is represented by devlink and ports are
represented by devlink ports, make debugfs file names independent
on netdev names. Change the topology to the one illustrated
by the following example:
$ ls /sys/kernel/debug/netdevsim/
netdevsim1
$ ls /sys/kernel/debug/netdevsim/netdevsim1/
bpf_bind_accept bpf_bind_verifier_delay bpf_bound_progs ports
$ ls /sys/kernel/debug/netdevsim/netdevsim1/ports/
0 1
$ ls /sys/kernel/debug/netdevsim/netdevsim1/ports/0/
bpf_map_accept bpf_offloaded_id bpf_tc_accept bpf_tc_non_bound_accept bpf_xdpdrv_accept bpf_xdpoffload_accept dev ipsec
$ ls /sys/kernel/debug/netdevsim/netdevsim1/ports/0/dev -l
lrwxrwxrwx 1 root root 0 Apr 13 15:58 /sys/kernel/debug/netdevsim/netdevsim1/ports/0/dev -> ../../../netdevsim1
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation of parent_id/switch_id does not follow the
original idea of being unique. The values are "0", "1", etc. Instead of
that, generate 32 random bytes.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As previously introduce dev which is mapped 1:1 to a bus device covers
the purpose of the original shared device, merge the sdev code into dev.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are going to be called from bus probe/release(),
therefore make them independent on ns struct and rename accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a way to add new netdevsim device on netdevsim bus and also to
delete existing netdevsim device from the bus. Track the bus devices
in using a list.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of increments of u32 value, use ida to manage bus device ids.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to bus probing to work correctly, register a simple netdevsim
driver implementation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move netdevsim device registration into bus.c and alongside with that
the related sysfs attributes. Introduce new struct nsim_bus_dev to
represent a netdevsim device on netdevsim bus.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the code related to netdevsim bus is going to get bigger, move the
existing code to a separate file.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing devlink.c code is going to be extended to represent asic
device on a bus. As this is about more than just devlink,
rename the file. Do appropriate prefix renaming alongside with that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is one devlink instance created per network namespace.
That is quite odd considering the fact that devlink instance should
represent an ASIC. The following patches are going to move the devlink
instance even more down to a bus device, but until then, have one
devlink instance per netdevsim instance. Struct nsim_devlink is
introduced to hold fib setting.
The changes in the fib code are only related to holding the
configuration per devlink instance instead of network namespace.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a dependency of the subsequent patch, mode device registration to be
done earlier, directly in nsim_newlink().
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-04-25
Here's the main bluetooth-next pull request for the 5.2 kernel.
- Added support for Mediatek SDIO controllers
- Added support for Broadcom BCM2076B1 UART controller
- Added support for Marvel SD8987 chipset
- Fix buffer overflow bug in hidp protocol
- Various other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The minimum encryption key size for LE connections is 56 bits and to
align LE with BR/EDR, enforce 56 bits of minimum encryption key size for
BR/EDR connections as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Pull networking fixes from David Miller:
"Just the usual assortment of small'ish fixes:
1) Conntrack timeout is sometimes not initialized properly, from
Alexander Potapenko.
2) Add a reasonable range limit to tcp_min_rtt_wlen to avoid
undefined behavior. From ZhangXiaoxu.
3) des1 field of descriptor in stmmac driver is initialized with the
wrong variable. From Yue Haibing.
4) Increase mlxsw pci sw reset timeout a little bit more, from Ido
Schimmel.
5) Match IOT2000 stmmac devices more accurately, from Su Bao Cheng.
6) Fallback refcount fix in TLS code, from Jakub Kicinski.
7) Fix max MTU check when using XDP in mlx5, from Maxim Mikityanskiy.
8) Fix recursive locking in team driver, from Hangbin Liu.
9) Fix tls_set_device_offload_Rx() deadlock, from Jakub Kicinski.
10) Don't use napi_alloc_frag() outside of softiq context of socionext
driver, from Ilias Apalodimas.
11) MAC address increment overflow in ncsi, from Tao Ren.
12) Fix a regression in 8K/1M pool switching of RDS, from Zhu Yanjun.
13) ipv4_link_failure has to validate the headers that are actually
there because RAW sockets can pass in arbitrary garbage, from Eric
Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
ipv4: add sanity checks in ipv4_link_failure()
net/rose: fix unbound loop in rose_loopback_timer()
rxrpc: fix race condition in rxrpc_input_packet()
net: rds: exchange of 8K and 1M pool
net: vrf: Fix operation not supported when set vrf mac
net/ncsi: handle overflow when incrementing mac address
net: socionext: replace napi_alloc_frag with the netdev variant on init
net: atheros: fix spelling mistake "underun" -> "underrun"
spi: ST ST95HF NFC: declare missing of table
spi: Micrel eth switch: declare missing of table
net: stmmac: move stmmac_check_ether_addr() to driver probe
netfilter: fix nf_l4proto_log_invalid to log invalid packets
netfilter: never get/set skb->tstamp
netfilter: ebtables: CONFIG_COMPAT: drop a bogus WARN_ON
Documentation: decnet: remove reference to CONFIG_DECNET_ROUTE_FWMARK
dt-bindings: add an explanation for internal phy-mode
net/tls: don't leak IV and record seq when offload fails
net/tls: avoid potential deadlock in tls_set_device_offload_rx()
selftests/net: correct the return value for run_afpackettests
team: fix possible recursive locking when add slaves
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXMC1JAAKCRBiEGxRG/Sl
2wqGAQDgquetrxSJZ92rP4H6YRfAH7W6XDIYM9+lwUoc7u24ZgEAvbkOAJEKPapn
09bmRYE5sNsqNtKiqwxfkCQbgzo1XAg=
=lJEd
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED update from Jacek Anaszewski:
"A single change to MAINTAINERS:
We announce a new LED reviewer - Dan Murphy"
* tag 'leds-for-5.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
MAINTAINERS: LEDs: Add designated reviewer for LED subsystem
