In case there are multiple Marvell EHCI blocks in system, we need a
different bus name for each one. Otherwise debugfs gets mildly upset about
a directory name in usb/ehci:
debugfs: Directory 'mv ehci' with parent 'ehci' already present!
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200309130014.548168-2-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out the undocumented and reserved bits of port status/control
register of the root port need to be set to use the HCI in HSIC mode.
Typically the firmware does this, but that is not always good enough,
because the bits get lost if the HSIC clock is disabled (e.g. when
ehci-mv is build as a module).
This supplements commit 7b104f890a ("USB: EHCI: ehci-mv: add HSIC
support").
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200309130014.548168-1-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVIDIA VirtualLink (svid 0x955) has two altmode, vdo=0x1 for
VirtualLink DP mode and vdo=0x3 for NVIDIA test mode. NVIDIA
test device FTB (Function Test Board) reports altmode list with
vdo=0x3 first and then vdo=0x1. The list is:
SVID VDO
0xff01 0xc05
0x28de 0x8085
0x955 0x3
0x955 0x1
Current logic to assign mode value is based on order
in altmode list. This causes a mismatch of CON and SOP altmodes
since NVIDIA GPU connector has order of vdo=0x1 first and then
vdo=0x3. Fixing this by changing the order of vdo values
reported by NVIDIA test device. the new list will be:
SVID VDO
0xff01 0xc05
0x28de 0x8085
0x955 0x1085
0x955 0x3
Also NVIDIA VirtualLink (svid 0x955) uses pin E for display mode.
NVIDIA test device reports vdo of 0x1 so make sure vdo values
always have pin E assignement.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200310121912.57879-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311093003.24604-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable gate is being initialized and also checked and re-assigned
with values that are never read as it is being re-assigned later in a
for-loop with a new value. The assignments are redundant and can be
removed.
Addresses Coverity ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The shifting of buf[3] by 24 bits to the left will be promoted to
a 32 bit signed int and then sign-extended to an unsigned long. In
the unlikely event that the the top bit of buf[3] is set then all
then all the upper bits end up as also being set because of
the sign-extension and this affect the ev->post_bit_error sum.
Fix this by using the temporary u32 variable bit_error to avoid
the sign-extension promotion. This also removes the need to do the
computation twice.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 267897a470 ("[media] tda10071: implement DVBv5 statistics")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When loading new kernel via kexec, we need to shutdown host controller to
avoid any un-expected memory accessing during new kernel boot.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200306092328.41253-1-ran.wang_1@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Locking the connector in ucsi_register_displayport() to make
sure that nothing can access the displayport alternate mode
before the function has finished and the alternate mode is
actually ready.
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200311130006.41288-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the registration of the DisplayPort was not successful,
or if the port does not support DisplayPort alt mode in the
first place, the function ucsi_displayport_remove_partner()
will fail with NULL pointer dereference when it attempts to
access the driver data.
Adding a check to the function to make sure there really is
driver data for the device before modifying it.
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Reported-by: Andrea Gagliardi La Gala <andrea.lagala@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206365
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200311130006.41288-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek Hub (0bda:0x0487) used in Dell Dock WD19 sometimes drops off the
bus when bringing underlying ports from U3 to U0.
Disabling LPM on the hub during setting link state is not enough, so
let's disable LPM completely for this hub.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200205112633.25995-3-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add space around operators for improving the code
readability.
Reported by checkpatch.pl
git diff -w shows no difference.
diff of the .o files before and after the changes shows no difference.
Signed-off-by: Shreeya Patel <shreeya.patel23498@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Link: https://lore.kernel.org/r/20200311131742.31068-1-shreeya.patel23498@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This is required to support the Terratec S2 USB Box Revision 4, which
reused usb vid:pid, but has a different demodulator (m88ds3103b) at
i2c address 0x6a.
[fixed checkpatch issues]
Signed-off-by: Michael Bunk <micha@freedict.org>
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hauppauge 461e rev2 is a DVB-S/S2 usb device containing:
- m88ds3103b demod
- ts2022 tuner
- A8293 SEC
Device is the same as Hauppauge 461e,
except it contains updated m88ds3103b demod.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ds3103b demodulator identifies as an m88rs600, but requires different
clock settings and firmware, along with differences in register settings.
Changes were reverse engineered using an instrumented downstream GPLv2
driver to compare i2c traffic and clocking. The mclk functions are from
the downstream GPLv2 driver.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311092451.23933-4-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311092451.23933-3-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311092451.23933-2-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311091944.23185-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modified the 'clock-names' property by removing '_clk' from its name and
remove '_spi/sdio' from 'compatible' string.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Link: https://lore.kernel.org/r/20200307085523.7320-3-ajay.kathat@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: ath11k@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are many protocols that encode more than 32 bit. We want 64 bit
support so that BPF IR decoders can decode more than 32 bit. None of
the existing kernel IR decoders/encoders support 64 bit, for now.
The MSC_SCAN event can only contain 32 bit scancodes, so we only generate
MSC_SCAN events if the scancode fits into 32 bits. The full 64 bit
scancode can be read from the lirc chardev.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The at24 driver attempts to read a byte from the device to validate that
it's actually present, and if not, disables the vcc regulator and
returns -ENODEV. However, between the read and the error handling path,
pm_runtime_idle() is called and invokes the driver's suspend callback,
which also disables the vcc regulator. This leads to an underflow of the
regulator enable count if the EEPROM is not present.
Move the pm_runtime_suspend() call to be after the error handling path
to resolve this.
Fixes: cd5676db05 ("misc: eeprom: at24: support pm_runtime control")
Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In bluetooth core specification 4.2,
Vol 2, Part E, 7.8.9 LE Set Advertise Enable Command, it says
The Controller shall continue advertising until ...
or until a connection is created or ...
In these cases, advertising is then disabled.
Hence, advertising would be disabled before a connection is
established. In current kernel implementation, advertising would
be re-enabled when all connections are terminated.
The correct disconnection flow looks like
< HCI Command: Disconnect
> HCI Event: Command Status
Status: Success
> HCI Event: Disconnect Complete
Status: Success
Specifically, the last Disconnect Complete Event would trigger a
callback function hci_event.c:hci_disconn_complete_evt() to
cleanup the connection and re-enable advertising when proper.
However, sometimes, there might occur an exception in the controller
when disconnection is being executed. The disconnection flow might
then look like
< HCI Command: Disconnect
> HCI Event: Command Status
Status: Unknown Connection Identifier
Note that "> HCI Event: Disconnect Complete" is missing when such an
exception occurs. This would result in advertising staying disabled
forever since the connection in question is not cleaned up correctly.
To fix the controller exception issue, we need to do some connection
cleanup when the disconnect command status indicates an error.
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The definitions for the "qcom,smem-states" and "qcom,smem-state-names"
properties need to list their "$ref" under an "allOf" keyword.
In addition, fix two problems in the example at the end:
- Use #include for header files that define needed symbolic values
- Terminate the line that includes the "ipa-shared" register space
name with a comma rather than a semicolon
Finally, update some white space in the example for better alignment.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per the dt-binding the interrupt is optional so use
platform_get_irq_optional() instead of platform_get_irq(). Since
commit 7723f4c5ec ("driver core: platform: Add an error message to
platform_get_irq*()") platform_get_irq() produces an error message
orion-mdio f1072004.mdio: IRQ index 0 not found
which is perfectly normal if one hasn't specified the optional property
in the device tree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the bottom 12 bits contain the ATU bin occupancy statistics. The
upper bits need masking off.
Fixes: e0c69ca7df ("net: dsa: mv88e6xxx: Add ATU occupancy via devlink resources")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: fixes 2020-03-11
please apply the following patch series for qeth to netdev's net tree.
Just one fix to get the RX buffer pool resizing right, with two
preparatory cleanups.
This is on the larger side given where we are in the -rc cycle, but a
big chunk of the delta is just refactoring to make the fix look nice.
I intentionally split these off from yesterday's series. No objections
if you'd rather punt them to net-next, the series should apply cleanly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX buffer pool is allocated in qeth_alloc_qdio_queues().
A subsequent pool resizing is then handled in a very simple way:
first free the current pool, then allocate a new pool of the requested
size.
There's two ways where this can go wrong:
1. if the resize action happens _before_ the initial pool was allocated,
then a subsequent initialization will call qeth_alloc_qdio_queues()
and fill the pool with a second(!) set of pages. We consume twice the
planned amount of memory.
This is easy to fix - just skip the resizing if the queues haven't
been allocated yet.
2. if the initial pool was created by qeth_alloc_qdio_queues() but a
subsequent resizing fails, then the device has no(!) RX buffer pool.
The next initialization will _not_ call qeth_alloc_qdio_queues(), and
attempting to back the RX buffers with pages in
qeth_init_qdio_queues() will fail.
Not very difficult to fix either - instead of re-allocating the whole
pool, just allocate/free as many entries to match the desired size.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for a subsequent fix, split out helpers to allocate/free
individual pool entries.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX buffer elements are always backed with full pages, reflect this
in the pointer type.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Internet Assigned Numbers Authority (IANA) has recently assigned
a protocol number value of 143 for Ethernet [1].
Before this assignment, encapsulation mechanisms such as Segment Routing
used the IPv6-NoNxt protocol number (59) to indicate that the encapsulated
payload is an Ethernet frame.
In this patch, we add the definition of the Ethernet protocol number to the
kernel headers and update the SRv6 L2 tunnels to use it.
[1] https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml
Signed-off-by: Paolo Lungaroni <paolo.lungaroni@cnit.it>
Reviewed-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Acked-by: Ahmed Abdelsalam <ahmed.abdelsalam@gssi.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, DSA drivers should configure CPU and DSA ports to their
maximum speed. In many configurations this is sufficient to make the
link work.
In some cases it is necessary to configure the link to run slower,
e.g. because of limitations of the SoC it is connected to. Or back to
back PHYs are used and the PHY needs to be driven in order to
establish link. In this case, phylink is used.
Only instantiate phylink if it is required. If there is no PHY, or no
fixed link properties, phylink can upset a link which works in the
default configuration.
Fixes: 0e27921816 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/ibm/emac/core.c: In function __emac_mdio_write:
drivers/net/ethernet/ibm/emac/core.c:875:9: warning:
variable err set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse reports a warning at netlink_seq_start()
warning: context imbalance in netlink_seq_start() - wrong count at exit
The root cause is the missing annotation at netlink_seq_start()
Add the missing __acquires(RCU) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse reports warning at tcp_child_process()
warning: context imbalance in tcp_child_process() - unexpected unlock
The root cause is the missing annotation at tcp_child_process()
Add the missing __releases(&((child)->sk_lock.slock)) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse reports warnings at raw_seq_start() and raw_seq_stop()
warning: context imbalance in raw_seq_start() - wrong count at exit
warning: context imbalance in raw_seq_stop() - unexpected unlock
The root cause is the missing annotations at raw_seq_start()
and raw_seq_stop()
Add the missing __acquires(&h->lock) annotation
Add the missing __releases(&h->lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In their .attach callback, mq[prio] only add the qdiscs of the currently
active TX queues to the device's qdisc hash list.
If a user later increases the number of active TX queues, their qdiscs
are not visible via eg. 'tc qdisc show'.
Add a hook to netif_set_real_num_tx_queues() that walks all active
TX queues and adds those which are missing to the hash list.
CC: Eric Dumazet <edumazet@google.com>
CC: Jamal Hadi Salim <jhs@mojatatu.com>
CC: Cong Wang <xiyou.wangcong@gmail.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to play with gotos to jump over single statement.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In one error case, tpacket_rcv drops packets after incrementing the
ring producer index.
If this happens, it does not update tp_status to TP_STATUS_USER and
thus the reader is stalled for an iteration of the ring, causing out
of order arrival.
The only such error path is when virtio_net_hdr_from_skb fails due
to encountering an unknown GSO type.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an off-by-one error in strncpy size argument in
drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c. The issue is that in:
strncmp(opt, "eee_timer:", 6)
the passed string literal: "eee_timer:" has 10 bytes (without the NULL
byte) and the passed size argument is 6. As a result, the logic will
also accept other, malformed strings, e.g. "eee_tiXXX:".
This bug doesn't seem to have any security impact since its present in
module's cmdline parsing code.
Signed-off-by: Dominik Czarnota <dominik.b.czarnota@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 319a1d1947, stmmac only support basic HW stats type for
action. Set this field in the L3/L4 Filtering test so that it correctly
setups the filter instead of returning EOPNOTSUPP.
Fixes: 319a1d1947 ("flow_offload: check for basic action hw stats type")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
