Add a module parameter to select deep PS mode. And the mode
cannot be changed after the module has been inserted and probed.
If anyone wants to change the deep mode, should change the mode
and probe the device again to setup the changed deep mode.
When the device is probed, driver will check the deep PS mode
with different IC's PS mode suppotability. If none of the
PS mode is matched, the deep PS mode is changed to NONE,
means deep PS is disabled.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes LPS is not compatible with COEX's strategy, and
COEX will not allow driver to enter it.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Deep power save allows firmware/hardware to operate in a
lower power state. And the deep power save mode depends on
LPS mode. So, before entering deep PS, driver must first
enter LPS mode.
Under Deep PS, most of hardware functions are shutdown,
driver will not be able to read/write registers and transfer
data to the device. Hence TX path must be protected by each
interface. Take PCI for example, DMA engine should be idle,
and no nore activities on the PCI bus.
If driver wants to operate on the device, such as register
read/write, it must first acquire the mutex lock and wake
up from Deep PS, otherwise the behavior is undefined.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dynamic mechanism requires BB/RF working to adjust
hardware settings. But PS state periodically turns
off BB/RF, could lead to wrong setting.
So leave PS state before DM to make sure it works.
And then check if we can enter PS state again.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Protect LPS enter/leave routine with rtwdev->mutex.
This helps to synchronize with driver's states correctly.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The original design of LPS enter/leave routines allows
to control the LPS state by each interface. But the
hardware cannot actually handle it that way. This means
the hardware can only enter LPS once with an associated
port, so there is no need to keep tracking the state of
each vif.
Hence the logic of enter/leave LPS state can be simple,
just to check the state of the device's flag. And for
leaving LPS state, it will get the same port id to send
to inform the hardware.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove PS related *_irqsafe functions to avoid entering/leaving PS
under interrupt context. Instead, make PS decision in watch_dog.
This could simplify the logic and make the code look clean.
But it could have a little side-effect that if the driver is having
heavy traffic before the every-2-second watch_dog detect the traffic
and decide to leave PS, the thoughput will be lower. Once traffic is
detected by watch_dog and left PS state, the throughput will resume
to the peak the hardware ought to have again.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the driver doesn't reset the host's and device's indexes
in a single write, the indexes will become different in a
short period. And it will confuse the DMA engine, make it
start to process non-existed entries.
Better to Write-1-to-reset the indexes, for the DMA engine
to know that this is a reset of the H2C queue, not a kick
off.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These helper functions seems useless. And in some cases
we want to use test_and_[set/clear]_bit, these helpers
will make the code more complicated. So remove them.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c: In function rtl8723be_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c:2255:7: warning: variable reg_ecc set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c: In function rtl8723be_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c:2254:34: warning: variable reg_eac set but not used [-Wunused-but-set-variable]
They are not used since commit a619d1abe2 ("rtlwifi:
rtl8723be: Add new driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c: In function rtl92ee_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c:2805:34: warning: variable reg_ecc set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c: In function rtl92ee_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c:2804:34: warning: variable reg_eac set but not used [-Wunused-but-set-variable]
They are not used since commit b1a3bfc97c ("rtlwifi:
rtl8192ee: Move driver from staging to the regular tree")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c: In function rtl92ee_tx_fill_desc:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c:656:5: warning: variable short_gi set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c: In function rtl92ee_tx_fill_desc:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c:648:15: warning: variable buf_len set but not used [-Wunused-but-set-variable]
They are not used since commit f1d2b4d338 ("rtlwifi:
rtl818x: Move drivers into new realtek directory")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/efuse.c: In function efuse_pg_packet_write:
drivers/net/wireless/realtek/rtlwifi/efuse.c:937:24: warning: variable dataempty set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/efuse.c: In function efuse_get_current_size:
drivers/net/wireless/realtek/rtlwifi/efuse.c:1202:5: warning: variable hoffset set but not used [-Wunused-but-set-variable]
They are not used since commit f1d2b4d338 ("rtlwifi:
rtl818x: Move drivers into new realtek directory")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/ps.c: In function rtl_ps_set_rf_state:
drivers/net/wireless/realtek/rtlwifi/ps.c:71:19: warning: variable rtstate set but not used [-Wunused-but-set-variable]
It is not used since commit f1d2b4d338 ("rtlwifi:
rtl818x: Move drivers into new realtek directory")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rtl8xxxu_submit_int_urb if usb_submit_urb fails the allocated urb
should be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is clearer than copy/pasting the magic number '+ 2' around, and it
even saves the need for one existing comment.
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
alloc_workqueue is not checked for errors and as a result,
a potential NULL dereference could occur.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need to check "rtlhal->interface == INTF_PCI" twice in
_rtl_ps_inactive_ps(). The nested check is always true. Thus, the
expression can be simplified.
Signed-off-by: Denis Efremov <efremov@linux.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rtl_usb_probe if allocation for usb_data fails the allocated hw
should be released. In addition the allocated rtlpriv->usb_data should
be released on error handling path.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'rtstatus' local variable is not used,
so remove it for clean-up.
Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix bbp ready check in mt7601u_wait_bbp_ready. The issue is reported by
coverity with the following error:
Logical vs. bitwise operator
The expression's value does not depend on the operands; inadvertent use
of the wrong operator is a likely logic error.
Addresses-Coverity-ID: 1309441 ("Logical vs. bitwise operator")
Fixes: c869f77d6a ("add mt7601u driver")
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rsi_send_beacon, if rsi_prepare_beacon fails the allocated skb should
be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless/realtek/rtw88/rtw8822c.c:2606:9-10: WARNING: return
of 0/1 in function 'rtw8822c_dpk_coef_iq_check' with return type bool
Return statements in functions returning bool should use true/false
instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Fixes: 5227c2ee45 ("rtw88: 8822c: add SW DPK support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The nested 'li_mimo == &locale_bn' check is excessive and always
true. Thus it can be safely removed.
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac assumed the wifi device always remains powered on and thus
hardcoded the MMC_PM_KEEP_POWER flag expecting the wifi device to
remain on even during suspend/resume cycles.
This is not always the case, some appliances cut power to everything
connected via SDIO for efficiency reasons and this leads to wifi not
being usable after coming out of suspend because the device was not
correctly reinitialized.
So we check for the keep_power capability and if it's not present then
we remove the device and probe it again during resume to mirror what's
happening in hardware and ensure correct reinitialization in the case
when MMC_PM_KEEP_POWER is not supported.
Suggested-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When n_reqs == 0 there is nothing to do so it doesn't make sense to
search for requests and issue a warning because none is found.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'pih' is known to be non-NULL at this point, so the test can be removed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With FT-802.1X, driver should send a port authorized event right after
sending a roamed event. It is used to indicate that a new AP is already
authorized so 802.1X is not required.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-----BEGIN PGP SIGNATURE-----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=2UM7
-----END PGP SIGNATURE-----
Merge tag 'for-5.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A bunch of fixes that accumulated in recent weeks, mostly material for
stable.
Summary:
- fix for regression from 5.3 that prevents to use balance convert
with single profile
- qgroup fixes: rescan race, accounting leak with multiple writers,
potential leak after io failure recovery
- fix for use after free in relocation (reported by KASAN)
- other error handling fixups"
* tag 'for-5.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: qgroup: Fix reserved data space leak if we have multiple reserve calls
btrfs: qgroup: Fix the wrong target io_tree when freeing reserved data space
btrfs: Fix a regression which we can't convert to SINGLE profile
btrfs: relocation: fix use-after-free on dead relocation roots
Btrfs: fix race setting up and completing qgroup rescan workers
Btrfs: fix missing error return if writeback for extent buffer never started
btrfs: adjust dirty_metadata_bytes after writeback failure of extent buffer
Btrfs: fix selftests failure due to uninitialized i_mode in test inodes
A few fixes that have trickled in through the merge window:
- Video fixes for OMAP due to panel-dpi driver removal
- Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7
- Fixing arch version on ASpeed ast2500
- Two fixes for reset handling on ARM SCMI
-----BEGIN PGP SIGNATURE-----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=s4qF
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes that have trickled in through the merge window:
- Video fixes for OMAP due to panel-dpi driver removal
- Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7
- Fixing arch version on ASpeed ast2500
- Two fixes for reset handling on ARM SCMI"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: aspeed: ast2500 is ARMv6K
reset: reset-scmi: add missing handle initialisation
firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
ARM: dts: am3517-evm: Fix missing video
ARM: dts: logicpd-torpedo-baseboard: Fix missing video
ARM: omap2plus_defconfig: Fix missing video
bus: ti-sysc: Fix handling of invalid clocks
bus: ti-sysc: Fix clock handling for no-idle quirks
- Fixed a buffer overflow by checking nr_args correctly in probes
- Fixed a warning that is reported by clang
- Fixed a possible memory leak in error path of filter processing
- Fixed the selftest that checks for failures, but wasn't failing
- Minor clean up on call site output of a memory trace event
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXZEP5hQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qhrSAQDlws8rY/vJN4tKL1YaBTRyS5OW+1B+
LPLOxm9PBuzt0wEArVunv7iMgvRzp5spbmCqmD8Is2vSf+45KSrb10WU2wo=
=L37R
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"A few more tracing fixes:
- Fix a buffer overflow by checking nr_args correctly in probes
- Fix a warning that is reported by clang
- Fix a possible memory leak in error path of filter processing
- Fix the selftest that checks for failures, but wasn't failing
- Minor clean up on call site output of a memory trace event"
* tag 'trace-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
selftests/ftrace: Fix same probe error test
mm, tracing: Print symbol name for call_site in trace events
tracing: Have error path in predicate_parse() free its allocated memory
tracing: Fix clang -Wint-in-bool-context warnings in IF_ASSIGN macro
tracing/probe: Fix to check the difference of nr_args before adding probe
Move the static keyword to the front of declaration of
csky_pmu_of_device_ids, and resolve the following compiler
warning that can be seen when building with warnings
enabled (W=1):
arch/csky/kernel/perf_event.c:1340:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Since the enabling and disabling of IRQs within preempt_schedule_irq()
is contained in a need_resched() loop, we don't need the outer arch
code loop.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Here are 2 small Documentation/process/embargoed-hardware-issues.rst
file updates that missed my previous char/misc pull request for 5.4-rc1.
The first one adds an Intel representative for the process, and the
second one cleans up the text a bit more when it comes to how the
disclosure rules work, as it was a bit confusing to some companies.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXZCMVg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymk1QCfarO6D7Wj/eg/BPSSkP/dgaLMog8AoLBJiBmz
2ErEIjIqV0J/e3QYud8G
=qUtH
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Documentation/process update from Greg KH:
"Here are two small Documentation/process/embargoed-hardware-issues.rst
file updates that missed my previous char/misc pull request.
The first one adds an Intel representative for the process, and the
second one cleans up the text a bit more when it comes to how the
disclosure rules work, as it was a bit confusing to some companies"
* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Documentation/process: Clarify disclosure rules
Documentation/process: Volunteer as the ambassador for Intel
Pull more vfs updates from Al Viro:
"A couple of misc patches"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
afs dynroot: switch to simple_dir_operations
fs/handle.c - fix up kerneldoc
-----BEGIN PGP SIGNATURE-----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=o1/m
-----END PGP SIGNATURE-----
Merge tag '5.4-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull more cifs updates from Steve French:
"Fixes from the recent SMB3 Test events and Storage Developer
Conference (held the last two weeks).
Here are nine smb3 patches including an important patch for debugging
traces with wireshark, with three patches marked for stable.
Additional fixes from last week to better handle some newly discovered
reparse points, and a fix the create/mkdir path for setting the mode
more atomically (in SMB3 Create security descriptor context), and one
for path name processing are still being tested so are not included
here"
* tag '5.4-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix oplock handling for SMB 2.1+ protocols
smb3: missing ACL related flags
smb3: pass mode bits into create calls
smb3: Add missing reparse tags
CIFS: fix max ea value size
fs/cifs/sess.c: Remove set but not used variable 'capabilities'
fs/cifs/smb2pdu.c: Make SMB2_notify_init static
smb3: fix leak in "open on server" perf counter
smb3: allow decryption keys to be dumped by admin for debugging
The csky_pmu.max_period has type u64, and BIT() can only return
32 bits unsigned long on C-SKY. The initialization for max_period
will be incorrect when count_width is bigger than 32.
Use BIT_ULL()
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
We need set fp zero to let backtrace know the end. The patch fixup perf
callchain panic problem, because backtrace didn't know what is the end
of fp.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reported-by: Mao Han <han_mao@c-sky.com>
The csky implementation of free_initrd_mem() is an open-coded version of
free_reserved_area() without poisoning.
Remove it and make csky use the generic version of free_initrd_mem().
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Merge active entropy generation updates.
This is admittedly partly "for discussion". We need to have a way
forward for the boot time deadlocks where user space ends up waiting for
more entropy, but no entropy is forthcoming because the system is
entirely idle just waiting for something to happen.
While this was triggered by what is arguably a user space bug with
GDM/gnome-session asking for secure randomness during early boot, when
they didn't even need any such truly secure thing, the issue ends up
being that our "getrandom()" interface is prone to that kind of
confusion, because people don't think very hard about whether they want
to block for sufficient amounts of entropy.
The approach here-in is to decide to not just passively wait for entropy
to happen, but to start actively collecting it if it is missing. This
is not necessarily always possible, but if the architecture has a CPU
cycle counter, there is a fair amount of noise in the exact timings of
reasonably complex loads.
We may end up tweaking the load and the entropy estimates, but this
should be at least a reasonable starting point.
As part of this, we also revert the revert of the ext4 IO pattern
improvement that ended up triggering the reported lack of external
entropy.
* getrandom() active entropy waiting:
Revert "Revert "ext4: make __ext4_get_inode_loc plug""
random: try to actively add entropy rather than passively wait for it
This reverts commit 72dbcf7215.
Instead of waiting forever for entropy that may just not happen, we now
try to actively generate entropy when required, and are thus hopefully
avoiding the problem that caused the nice ext4 IO pattern fix to be
reverted.
So revert the revert.
Cc: Ahmed S. Darwish <darwish.07@gmail.com>
Cc: Ted Ts'o <tytso@mit.edu>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Alexander E. Patrakov <patrakov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For 5.3 we had to revert a nice ext4 IO pattern improvement, because it
caused a bootup regression due to lack of entropy at bootup together
with arguably broken user space that was asking for secure random
numbers when it really didn't need to.
See commit 72dbcf7215 (Revert "ext4: make __ext4_get_inode_loc plug").
This aims to solve the issue by actively generating entropy noise using
the CPU cycle counter when waiting for the random number generator to
initialize. This only works when you have a high-frequency time stamp
counter available, but that's the case on all modern x86 CPU's, and on
most other modern CPU's too.
What we do is to generate jitter entropy from the CPU cycle counter
under a somewhat complex load: calling the scheduler while also
guaranteeing a certain amount of timing noise by also triggering a
timer.
I'm sure we can tweak this, and that people will want to look at other
alternatives, but there's been a number of papers written on jitter
entropy, and this should really be fairly conservative by crediting one
bit of entropy for every timer-induced jump in the cycle counter. Not
because the timer itself would be all that unpredictable, but because
the interaction between the timer and the loop is going to be.
Even if (and perhaps particularly if) the timer actually happens on
another CPU, the cacheline interaction between the loop that reads the
cycle counter and the timer itself firing is going to add perturbations
to the cycle counter values that get mixed into the entropy pool.
As Thomas pointed out, with a modern out-of-order CPU, even quite simple
loops show a fair amount of hard-to-predict timing variability even in
the absense of external interrupts. But this tries to take that further
by actually having a fairly complex interaction.
This is not going to solve the entropy issue for architectures that have
no CPU cycle counter, but it's not clear how (and if) that is solvable,
and the hardware in question is largely starting to be irrelevant. And
by doing this we can at least avoid some of the even more contentious
approaches (like making the entropy waiting time out in order to avoid
the possibly unbounded waiting).
Cc: Ahmed Darwish <darwish.07@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Nicholas Mc Guire <hofrat@opentech.at>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Alexander E. Patrakov <patrakov@gmail.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes for omap variants
Few fixes for ti-sysc interconnect target module driver for no-idle
quirks that caused nfsroot to fail on some dra7 boards.
And let's fixes to get LCD working again for logicpd board that got
broken a while back with removal of panel-dpi driver. We need to now
use generic CONFIG_DRM_PANEL_SIMPLE instead.
* tag 'fixes-5.4-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
ARM: dts: am3517-evm: Fix missing video
ARM: dts: logicpd-torpedo-baseboard: Fix missing video
ARM: omap2plus_defconfig: Fix missing video
bus: ti-sysc: Fix handling of invalid clocks
bus: ti-sysc: Fix clock handling for no-idle quirks
Link: https://lore.kernel.org/r/pull-1568819401-72461@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Couple of fixes: one in scmi reset driver initialising missed scmi handle
and an other in scmi reset API implementation fixing the assignment of
reset state
-----BEGIN PGP SIGNATURE-----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=FmDn
-----END PGP SIGNATURE-----
Merge tag 'scmi-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
ARM SCMI fixes for v5.4
Couple of fixes: one in scmi reset driver initialising missed scmi handle
and an other in scmi reset API implementation fixing the assignment of
reset state
* tag 'scmi-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
reset: reset-scmi: add missing handle initialisation
firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
Link: https://lore.kernel.org/r/20190918142139.GA4370@bogus
Signed-off-by: Olof Johansson <olof@lixom.net>
- Complete the reworks to interoperate with powerpc dynamic huge page sizes
- Fix a crash due to missed accounting for the powerpc 'struct
page'-memmap mapping granularity.
- Fix badblock initialization for volatile (DRAM emulated) pmem ranges.
- Stop triggering request_key() notifications to userspace when
NVDIMM-security is disabled / not present.
- Miscellaneous small fixups.
-----BEGIN PGP SIGNATURE-----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=Z6Fa
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-fixes-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
More libnvdimm updates from Dan Williams:
- Complete the reworks to interoperate with powerpc dynamic huge page
sizes
- Fix a crash due to missed accounting for the powerpc 'struct
page'-memmap mapping granularity
- Fix badblock initialization for volatile (DRAM emulated) pmem ranges
- Stop triggering request_key() notifications to userspace when
NVDIMM-security is disabled / not present
- Miscellaneous small fixups
* tag 'libnvdimm-fixes-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm/region: Enable MAP_SYNC for volatile regions
libnvdimm: prevent nvdimm from requesting key when security is disabled
libnvdimm/region: Initialize bad block for volatile namespaces
libnvdimm/nfit_test: Fix acpi_handle redefinition
libnvdimm/altmap: Track namespace boundaries in altmap
libnvdimm: Fix endian conversion issues
libnvdimm/dax: Pick the right alignment default when creating dax devices
powerpc/book3s64: Export has_transparent_hugepage() related functions.
