Initialize maar by resource map and replace page_is_ram
by memblock_is_memory.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
[paul.burton@mips.com:
- Fix bad MAAR address calculations.
- Use ALIGN() & define maar_align to make it clearer what's going on
with address manipulations.
- Drop the new used field from struct maar_config.
- Rework the RAM walk to avoid iterating over the cfg array needlessly
to find the first unused entry, then count used entries at the end.
Instead just keep the count as we go.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: yasha.che3@gmail.com
Cc: aurelien@aurel32.net
Cc: sfr@canb.auug.org.au
Cc: fancer.lancer@gmail.com
Cc: matt.redfearn@mips.com
Cc: chenhc@lemote.com
Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is called
bcm43356 and can be used with the brcmfmac driver. The module is powered by
the two always on regulators (not AXP805).
WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be
configured so that it sets up an 1.8V input bias on this port. This is done
by the pio driver by reading the vcc-pg-supply voltage.
You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt
configuration that can be found in the Xulongs's repository for H6:
https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256
Mainline brcmfmac driver expects the firmware and nvram at the following
paths relative to the firmware directory:
brcm/brcmfmac43456-sdio.bin
brcm/brcmfmac43456-sdio.txt
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Translation faults arising from cache maintenance instructions are
rather unhelpfully reported with an FSR value where the WnR field is set
to 1, indicating that the faulting access was a write. Since cache
maintenance instructions on 32-bit ARM do not require any particular
permissions, this can cause our private 'cacheflush' system call to fail
spuriously if a translation fault is generated due to page aging when
targetting a read-only VMA.
In this situation, we will return -EFAULT to userspace, although this is
unfortunately suppressed by the popular '__builtin___clear_cache()'
intrinsic provided by GCC, which returns void.
Although it's tempting to write this off as a userspace issue, we can
actually do a little bit better on CPUs that support LPAE, even if the
short-descriptor format is in use. On these CPUs, cache maintenance
faults additionally set the CM field in the FSR, which we can use to
suppress the write permission checks in the page fault handler and
succeed in performing cache maintenance to read-only areas even in the
presence of a translation fault.
Reported-by: Orion Hodson <oth@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Since commit ad67b74d24 ("printk: hash addresses printed with
%p"), an obfuscated kernel pointer is printed at every boot if
debugging is enabled:
vdso: 1 text pages at base (____ptrval____)
Remove the print completely, as it's useless without the address.
Based on commit 0f1bf7e398 ("arm64/vdso: don't leak kernel
addresses").
Fixes: ad67b74d24 ("printk: hash addresses printed with %p")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
When you run "make clean" for arm, it never visits mach-* or plat-*
directories because machine-y and plat-y are just empty.
When cleaning, all machine, plat directories are accumulated to
machine-, plat-, respectively. So, let's pass them to core- to
clean up those directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This open-coded nop as mov r0, r0 is a development history
artifact.
First commit b11fe38883
("ARM: 6663/1: make Thumb2 kernel entry point more similar
to the ARM one") moved the code around so that the nops
would come before the conditional thumb instructions, as it
turned out that some boot loaders were patching the initial
nop instructions in the kernel. At this point it is clear
that all mov r0,r0 are open-coded nops.
Then commit 81a0bc39ea ("ARM: add UEFI stub support")
moved things around and defined __nop for EFI support and
missed this open-coded nop.
commit 06a4b6d009
("ARM: 8677/1: boot/compressed: fix decompressor header
layout for v7-M") makes all invocations of __nop be wide,
but that is fine, because this is what we want: the
mov r0,r0 is inside ifndef CONFIG_THUMB2_KERNEL.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Roy Franz <rfranz@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This was unclear to me until Russell explained the obvious
that 8 nops are added to offset an a.out image. Reading
git history reveals that thumb kernels first removed the
nops and then kept 7 of them (the last instruction being
a switch to thumb mode) as it turns out that some boot
loaders were using this as a "patch area". Also the magic
numbers after the initial nops and the jump of course
need to stay in the same offset for kernel file
detection.
Make the code easier to understand with a comment.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Roy Franz <rfranz@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
To use Fastfpe, a user is supposed to enable CONFIG_FPE_FASTFPE
and put downstream source files into arch/arm/fastfpe/.
It is not working for O= build because $(wildcard arch/arm/fastfpe)
checks if it exists in $(objtree), not in $(srctree).
Add the $(srctree)/ prefix to fix it.
While I was here, I slightly refactored the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Clang produces references to __aeabi_uidivmod and __aeabi_idivmod for
arm-linux-gnueabi and arm-linux-gnueabihf targets incorrectly when AEABI
is not selected (such as when OABI_COMPAT is selected).
While this means that OABI userspaces wont be able to upgraded to
kernels built with Clang, it means that boards that don't enable AEABI
like s3c2410_defconfig will stop failing to link in KernelCI when built
with Clang.
Link: https://github.com/ClangBuiltLinux/linux/issues/482
Link: https://groups.google.com/forum/#!msg/clang-built-linux/yydsAAux5hk/GxjqJSW-AQAJ
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
There is error from cppcheck tool.
"Shifting signed 32-bit value by 31 bits is undefined behaviour errors"
This error is false positive.
change to use BIT() macro for improvement.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This commit removes the open-coded CPU-offline notification with new
common code. In particular, this change avoids calling scheduler code
using RCU from an offline CPU that RCU is ignoring. This is a minimal
change. A more intrusive change might invoke the cpu_check_up_prepare()
and cpu_set_state_online() functions at CPU-online time, which would
allow onlining throw an error if the CPU did not go offline properly.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: linux-arm-kernel@lists.infradead.org
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
clang warns:
arch/arm/mach-iop13xx/pci.c:292:7: warning: logical not is only applied
to the left hand side of this comparison [-Wlogical-not-parentheses]
if (!iop13xx_atux_pci_status(1) == 0)
^ ~~
arch/arm/mach-iop13xx/pci.c:439:7: warning: logical not is only applied
to the left hand side of this comparison [-Wlogical-not-parentheses]
if (!iop13xx_atue_pci_status(1) == 0)
^ ~~
!func() == 0 is equivalent to func(), which clears up this warning and
makes the code more readable.
Link: https://github.com/ClangBuiltLinux/linux/issues/543
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
In the commit ef41b5c924 ("ARM: make kernel oops easier to read"),
- .word 0xe92d0000 >> 10 @ stmfd sp!, {}
+ .word 0xe92d0000 >> 11 @ stmfd sp!, {}
then the shift need to change to 11.
Signed-off-by: Lvqiang Huang <Lvqiang.Huang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
A timing hazard exists when an early fork/exec thread begins
exiting and sets its mm pointer to NULL while a separate core
tries to update the section information.
This commit ensures that the mm pointer is not NULL before
setting its section parameters. The arguments provided by
commit 11ce4b33ae ("ARM: 8672/1: mm: remove tasklist locking
from update_sections_early()") are equally valid for not
requiring grabbing the task_lock around this check.
Fixes: 08925c2f12 ("ARM: 8464/1: Update all mm structures with section adjustments")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The watchdog has a clock on all our SoCs, but it wasn't always listed.
Add it to the devicetree where it's missing.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The watchdog has an interrupt on all our SoCs, but it wasn't always listed.
Add it to the devicetree where it's missing.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This patch adds RTC node and fixes the clock properties and nodes
to reflect the real clock tree.
The device nodes for the internal oscillator and osc32k are removed,
as these clocks are now provided by the RTC device. Clock references
are fixed accordingly, too.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This variable has no users anymore. Remove it and tell the
IOMMU code via its new functions about requested DMA modes.
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The CSI controller embedded in the A20 can be supported by our new driver.
Let's add it to our DT.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.
This patch has been tested on A64-OLinuXino-1Ge16GW with Linux 5.0 from Debain.
Basic benchmarks using Flexible IO Tester show reasonable performance from the
eMMC.
eMMC - Random Write: 21.3MiB/s
eMMC - Sequential Write: 68.2MiB/s
SD Card - Random Write: 1690KiB/s
SD Card - Sequential Write: 11.0MiB/s
Changes:
v3: Separate dts for eMMC variants
v2: Fix descriptions for VCC and VCCQ
Link: 174953de1e
Signed-off-by: Martin Ayotte <martinayotte@gmail.com>
[sunil@medhas.org Fix descriptions for VCC and VCCQ, separate dts for eMMC]
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
Tested-by: Sunil Mohan Adapa <sunil@medhas.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Unlike the A10 that has 6 timers available, the v3s has only three, with only
three interrupts. Let's change the compatible to reflect that, and add the
missing interrupts.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Unlike the A10 that has 6 timers available, the H3 has only two, with only
two interrupts, just like the A23. Let's change the compatible to reflect
that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Unlike the A10 that has 6 timers available, the A83t has only two, with
only two interrupts, just like the A23. Let's change the compatible to
reflect that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Unlike the A10 that has 6 timers available, the A23 and A33 has only two,
with only two interrupts. Let's change the compatible to reflect that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tanix TX6 is an Allwinner H6 based TV box, which supports:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 4GiB DDR3 RAM (3GiB useable)
- 100Mbps EMAC via AC200 EPHY
- Cdtech 47822BS Wifi/BT
- 2x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- IR receiver
- 64GiB eMMC
- 5V/2A DC power supply
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add device-tree nodes for i2c0 to i2c2, and also add relevant pinctrl
nodes.
Suggested-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The DWMAC binding never supported having the Ethernet PHY node as a
direct child to the controller, nor did it support the "phy" property
as a way to specify which Ethernet PHY to use. What seemed to work
was simply the implementation ignoring the "phy" property and instead
probing all addresses on the MDIO bus and using the first available
one.
The recent switch from "phy" to "phy-handle" breaks the assumptions
of the implementation, and does not match what the binding requires.
The binding requires that if an MDIO bus is described, it shall be
a sub-node with the "snps,dwmac-mdio" compatible string.
Add a device node for the MDIO bus, and move the Ethernet PHY node
under it. Also fix up the #address-cells and #size-cells properties
where needed.
Fixes: de332de26d ("ARM: dts: sunxi: Switch from phy to phy-handle")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Beelink GS1 has a DDC I2C bus voltage shifter. This is actually missing
and video is limited to 1024x768 due to missing EDID information.
Add the DDC regulator in the device-tree.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Beelink GS1 board has a SPDIF out connector, so enable it in
the device-tree and add a simple SPDIF soundcard.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 has a SPDIF controller called OWA (One Wire Audio).
Only one pinmuxing is available so set it as default.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Lichee zero plus is a core board made by Sipeed, which includes on-board
TF slot or SMT SD NAND, and optional SPI NOR or eMMC, a UART debug
header, a microUSB slot and a gold finger connector for expansion. It
can use either Sochip S3 or Allwinner S3L SoC.
Add the basic device tree for the core board, w/o optional onboard
storage, and with S3 SoC.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner S3/S3L/V3 SoCs all share the same die with the V3s SoC,
but with more GPIO wired out of the package.
Add a DTSI file for these SoCs. It just replaces some compatible strings
of the V3s DTSI now. As these SoCs share the same feature set on Linux,
we use the first known chip (V3) as the file's name.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Orange Pi 3 has a DDC_CEC_EN signal connected to PH2, that enables the DDC
I2C bus voltage shifter. Before EDID can be read, we need to pull PH2 high.
This is realized by the ddc-en-gpios property.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Cubietruck Plus has an HDMI connector tied to the HDMI output of the
SoC.
Enables display output via HDMI on the Cubietruck Plus. The connector
device node is named "hdmi-connector" as there is also a display port
connector, which is tied to the MIPI DSI output of the SoC through a
MIPI-DSI-to-DP bridge. This part is not supported yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The rmap array in the guest memslot is an array of size number of guest
pages, allocated at memslot creation time. Each rmap entry in this array
is used to store information about the guest page to which it
corresponds. For example for a hpt guest it is used to store a lock bit,
rc bits, a present bit and the index of a hpt entry in the guest hpt
which maps this page. For a radix guest which is running nested guests
it is used to store a pointer to a linked list of nested rmap entries
which store the nested guest physical address which maps this guest
address and for which there is a pte in the shadow page table.
As there are currently two uses for the rmap array, and the potential
for this to expand to more in the future, define a type field (being the
top 8 bits of the rmap entry) to be used to define the type of the rmap
entry which is currently present and define two values for this field
for the two current uses of the rmap array.
Since the nested case uses the rmap entry to store a pointer, define
this type as having the two high bits set as is expected for a pointer.
Define the hpt entry type as having bit 56 set (bit 7 IBM bit ordering).
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Fix the error below triggered by `-Wimplicit-fallthrough`, by tagging
it as an expected fall-through.
arch/powerpc/kvm/book3s_32_mmu.c: In function ‘kvmppc_mmu_book3s_32_xlate_pte’:
arch/powerpc/kvm/book3s_32_mmu.c:241:21: error: this statement may fall through [-Werror=implicit-fallthrough=]
pte->may_write = true;
~~~~~~~~~~~~~~~^~~~~~
arch/powerpc/kvm/book3s_32_mmu.c:242:5: note: here
case 3:
^~~~
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This merges in fixes for the XIVE interrupt controller which touch both
generic powerpc and PPC KVM code. To avoid merge conflicts, these
commits will go upstream via the powerpc tree as well as the KVM tree.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Unfortunately, my build fix for when time travel mode isn't
enabled broke time travel mode, because I forgot that we need
to use the timer time after the timer has been marked disabled,
and thus need to leave the time stored instead of zeroing it.
Fix that by splitting the inline into two, so we can call only
the _mode() one in the relevant code path.
Fixes: b482e48d29 ("um: fix build without CONFIG_UML_TIME_TRAVEL_SUPPORT")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Since there is no one using this board, remove it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
