CodingStyle describes that either none or both branches of a conditional
have to have brackets.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
It is just a bit easier to put the error handling at one place and let
multiple error paths use the same calls.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The HID device does not need to know about the ACPI device associated with
the underlying i2c device. Setting the ACPI companion field in the HID device
also has the side effect of causing HID to be set as wake capable, since
acpi_bind_one uses's the companion ACPI device's wakeup flags to set the
device as wake capable. Which results in power/wakeup files in sysfs for
the HID device which do not do anything.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Tested-by: Benson Leung <bleung@chromium.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This commit makes sure that on process termination, after
we're destroying all the active queues, we're killing all the
existing wave front of the current process.
By doing this we're making sure that if any of the CUs were blocked
by infinite loop we're enforcing it to end the shader explicitly.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This patch adds three new interfaces to kfd2kgd interface file of radeon.
The interfaces are:
- Check if a specific VMID has a valid PASID mapping
- Retrieve the PASID which is mapped to a specific VMID
- Issue a VMID invalidation request to the ATC
Signed-off-by: Alexey Skidanov <Alexey.Skidanov@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
v2:
- rename get_dbgmgr_mutex to kfd_get_dbgmgr_mutex to namespace it
- change void* to uint64_t inside ioctl arguments
- use kmalloc instead of kzalloc because we use copy_from_user
immediately after it
Signed-off-by: Yair Shachar <yair.shachar@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
v2:
- rename get_dbgmgr_mutex to kfd_get_dbgmgr_mutex to namespace it
- change void* to uint64_t inside ioctl arguments
- use kmalloc instead of kzalloc because we use copy_from_user
immediately after it
Signed-off-by: Yair Shachar <yair.shachar@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The address watch operation gives the ability to specify watch points
which will generate a shader breakpoint, based on a specified single
address or range of addresses.
There is support for read/write/any access modes.
Signed-off-by: Yair Shachar <yair.shachar@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The wave control operation supports several command types executed upon
existing wave fronts that belong to the currently debugged process.
The available commands are:
HALT - Freeze wave front(s) execution
RESUME - Resume freezed wave front(s) execution
KILL - Kill existing wave front(s)
Signed-off-by: Yair Shachar <yair.shachar@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This patch adds the skeleton H/W debugger module support. This code
enables registration and unregistration of a single HSA process at a
time.
The module saves the process's pasid and use it to verify that only the
registered process is allowed to execute debugger operations through the
kernel driver.
v2: rename get_dbgmgr_mutex to kfd_get_dbgmgr_mutex to namespace it
Signed-off-by: Yair Shachar <yair.shachar@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This patch adds support for static user-mode queues in QCM.
Queues which are designated as static can NOT be preempted by
the CP microcode when it is executing its scheduling algorithm.
This is needed for supporting the debugger feature, because we
can't allow the CP to preempt queues which are currently being debugged.
The number of queues that can be designated as static is limited by the
number of HQDs (Hardware Queue Descriptors).
Signed-off-by: Yair Shachar <yair.shachar@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This patch adds four new IOCTLs to amdkfd. These IOCTLs expose a H/W
debugger functionality to the userspace.
The IOCTLs are:
- AMDKFD_IOC_DBG_REGISTER:
The purpose of this IOCTL is to notify amdkfd that a process wants to use
GPU debugging facilities on itself only.
It is expected that this IOCTL would be called before any other H/W
debugger requests are sent to amdkfd and for each GPU where the H/W
debugging needs to be enabled. The use of this IOCTL ensures that only
one instance of a debugger is active in the system.
- AMDKFD_IOC_DBG_UNREGISTER:
This IOCTL detaches the debugger/debugged process from the H/W
Debug which was established by the AMDKFD_IOC_DBG_REGISTER IOCTL.
- AMDKFD_IOC_DBG_ADDRESS_WATCH:
This IOCTL allows to set different watchpoints with various conditions as
indicated by the IOCTL's arguments. The available number of watchpoints
is retrieved from topology. This operation is confined to the current
debugged process, which was registered through AMDKFD_IOC_DBG_REGISTER.
- AMDKFD_IOC_DBG_WAVE_CONTROL:
This IOCTL allows to control a wavefront as indicated by the IOCTL's
arguments. For example, you can halt/resume or kill either a
single wavefront or a set of wavefronts. This operation is confined to
the current debugged process, which was registered through
AMDKFD_IOC_DBG_REGISTER.
Because the arguments for the address watch IOCTL and wave control IOCTL
are dynamic, meaning that they could vary in size, the userspace passes a
pointer to a structure (in userspace) that contains the value of the
arguments. The kernel driver is responsible to parse this structure and
validate its contents.
v2: change void* to uint64_t inside ioctl arguments
Signed-off-by: Yair Shachar <yair.shachar@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This patch adds new interface functions to the kfd2kgd interface file. The
new functions allow to perform H/W debugger operations by writing to GPU
registers.
Signed-off-by: Yair Shachar <yair.shachar@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Use the generic mechanism to declare a bitmap instead of unsigned long.
It seems that "struct kfd_process.allocated_queue_bitmap" is unused.
Maybe it could be deleted instead.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Peter Zijstra noticed that in arch/x86/Kconfig there are a lot
of X86_{32,64} clauses in the X86 symbol, plus there are a number
of similar selects in the X86_32 and X86_64 config definitions
as well - which all overlap in an inconsistent mess.
So:
- move all select's from X86_32 and X86_64 to the X64 config
option
- sort their names, so that duplications are easier to spot
- align their if clauses, so that they are easier to identify
at a glance - and so that weirdnesses stand out more
No change in functionality:
105 insertions(+)
105 deletions(-)
Originally-from: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20150602153027.GU3644@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Remove the line-break in the user-visible string and add the
missing space in this error message:
WARNING: lockdep init error! lock-(console_sem).lock was acquiredbefore lockdep_init
Also:
- don't yell, it's just a debug warning
- denote references to function calls with '()'
- standardize the lock name quoting
- and finish the sentence.
The result:
WARNING: lockdep init error: lock '(console_sem).lock' was acquired before lockdep_init().
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20150602133827.GD19887@pd.tnic
[ Added a few more stylistic tweaks to the error message. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Use the default FCSR value in mask probing, avoiding an FPE exception
where reset has left any exception enable and their corresponding cause
bits set and the register is then rewritten with these bits active.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
After the new ciphers CCMP-256 and GCMP-128/256 were implemented,
wpa_supplicant could start negotiating them and use the software
implementation. This, however, breaks D3 behaviour in the driver
since it means that WoWLAN will not be possible.
To avoid breaking that feature, advertise only ciphers that the
hardware supports.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch adds support for the imx6dl based aristainetos2 board
with following configuration:
CPU: Freescale i.MX6DL rev1.1 at 792 MHz
MReset cause: POR
MBoard: aristaitenos2
DRAM: 1 GiB
NAND: 1024 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected N25Q128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB
Display: lb07wv8 (800x480)
As this board can be used with 2 different display types, the
differences between them are extracted into 2 DTS files, and
the common settings are collected in a common file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Arrange the license text a bit to make it clear.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Also add label for backlight_lvds and connect it to the LVDS display.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Also add label for backlight_lvds and connect it to the display.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx7d intergrates the unique display controller for EPD panel, pixel engines
and graphics engines to make it a ideal solution for EPD based devices such
as eReader, Signage, as well as any application rely on the bistable charactersic
of the EPD panel.
imx7d include two ARM Cortex A7 Core and one Cortex-M4 core.
Included Main Peripheral
- DDR3\LP-DDR2
- GPMI\BCH\APBH DMA(NAND flash support)
- QSPI
- WEIM Nor
- LCDIF\MIPI DSI
- CSI\MIPI CSI
- EPDC
- PCIe RC\EP
- USB OTG\Host
- CAN x2
- I2C x4
- SIMv2 x2
- ENET -x2
- uSDHC x3
- eCSPI x1
- PWM x4
- OCOTP (fuse)
- GPT x4
- WDOG x4
- Flex Timer x2
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This commit includes a minor nomenclature fixup for boards based on the
Freescale VF610 SoC and which make use of the alternate "RMII1_RXD1"
functionality for pin PTC12. This brings the macro name in-line with
both the datasheet and other similar macros.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add DT support for the Broadcom Wifi/Bluetooth devices found on the
microsom board.
[Modified original Russell King's patch to use mmc-pwrseq]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Jon Nettleton <jon@solid-run.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This part just add necessary change to boot imx7d.
Update clock, pinctrl and gpt for imx7d
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CODA960 VPU is part of the PU power domain. Add power-domains
phandle so it can be associated with the PU generic pm domain for
power gating.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add support for the Gateworks GW5510 board featuring:
* i.MX6 SoC
* up to 512MB DDR3
* up to 2GB NAND flash
* 1x miniPCIe socket (with USB)
* HDMI out (micro-HDMI)
* HDMI in (micro-HDMI) (currently supported by only vendor kernel)
* TTL level I/O (supported by GW16111 breakout board):
* I2C
* 2x UART
* CAN
* 2x DIO (GPIO/PWM)
* USB OTG
For more details see:
http://www.gateworks.com/product/item/ventana-gw5510-single-board-computer
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
USBOTG1 always work on peripheral mode and USBOTG in host mode, so fix
their roles accordingly.
Tested by mounting the MMC card as a storage device:
modprobe g_mass_storage file=/dev/mmcblk0p2
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
According to the warp schematics there are no regulators for the USB OTG
ports, so let's remove them.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The 'reg_1p8v' regulator is not used anywhere, so let's remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch updates the in tree-users of the SSD1306 controller for using
the newly introduced DT properties.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add PCIe support. Based on a patch from Rabeeh Khoury from the solid-run
tree.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx23-olinuxino board has an i2c interface exposed on UEXT connector.
This patch enables i2c and selects the pin group used on UEXT connector.
Tested with MOD-LCD1x9 from Olimex.
This patch is based on work by Fadil Berisha with his permission. However
all bugs are mine.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx23-olinuxino board has an i2c interface exposed on UEXT connector.
This patch provides the generic devicetree infrastructure for a follow-up
patch to add support to the actual board files.
Tested all three possible pin groups with MOD-LCD1x9 from Olimex.
This patch is based on work by Fadil Berisha with his permission. However
all bugs are mine.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx6qdl-hummingboard boards use sgtl5000 codec and the machine file
(imx-sgtl5000) already sets SSI in slave mode and codec in master mode, so there
is no need for having the 'fsl,mode' property.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Currently the HDMI controller is a child device of the AIPS bus in the
DT which is clearly wrong. Move it to the right location.
This introduces no functional change it just aligns the DT representation
with reality.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add DC2DC_CONFIG_CMD (0x83) cmd.
Add IWL_UCODE_TLV_CAPA_DC2DC_CONFIG_SUPPORT tlv.
The command allows the driver get & set the DCDC's frequency tune.
(freq_tune is the divider that is used to calculate the actual DCDC's
clock rate)
The command always returns the current/updated frequency tune values of
the DCDC.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Like i.MX6, the i.MX7 code calls into the anatop driver, which fails
if that is disabled:
arch/arm/mach-imx/built-in.o: In function `imx7d_init_machine':
arch/arm/mach-imx/mach-imx7d.c:24: undefined reference to `imx_anatop_init'
arch/arm/mach-imx/built-in.o: In function `imx7d_init_irq':
arch/arm/mach-imx/mach-imx7d.c:29: undefined reference to `imx_init_revision_from_anatop'
This patch ensures that for an imx7-only build, we still get anatop
built-in, matching what we do for imx6. We also need to select
HAVE_IMX_MMDC, as that is needed by the anatop code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The include of <asm/mach/time.h> is not needed at all, and causes build
error in some cases. Remove it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
