The originally added 'regulators' device node has a number of flaws,
to name a few its children has unit addresses but no reg properties,
the regulators are not captured by a device driver due to a missing
'simple-bus' compatible, the regulator names are selected by killing
either alphabetical order or device node grouping property.
The change removes 'regulators' device node and renames the regulators
and labels.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The fixed voltage regulator on Phytec phyCORE-LPC3250 board, which
supplies SD/MMC card's power, has a constant output voltage level
of either 3.15V or 3.3V, the actual value depends on JP4 position,
the power rail is referenced as VCC_SDIO in the board hardware manual.
Fixes: d06670e962 ("arm: dts: phy3250: add SD fixed regulator")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The originally added ARM PrimeCell PL111 clocks property misses
the required "clcdclk" clock, which is the same as a clock to enable
the LCD controller on NXP LPC3230 and NXP LPC3250 SoCs.
Fixes: 93898eb775 ("arm: dts: lpc32xx: add clock properties to device nodes")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
ARM PrimeCell PL111 LCD controller is found on On NXP LPC3230
and LPC3250 SoCs variants, the original reference in compatible
property to an older one ARM PrimeCell PL110 is invalid.
Fixes: e04920d9ef ("ARM: LPC32xx: DTS files for device tree conversion")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
After switching to a new interrupt controller scheme by separating SIC1
and SIC2 from MIC interrupt controller just one SoC keypad controller
was not taken into account, fix it now:
WARNING: CPU: 0 PID: 1 at kernel/irq/irqdomain.c:524 irq_domain_associate+0x50/0x1b0
error: hwirq 0x36 is too large for interrupt-controller@40008000
...
lpc32xx_keys 40050000.key: failed to get platform irq
lpc32xx_keys: probe of 40050000.key failed with error -22
Fixes: 9b8ad3fb81 ("ARM: dts: lpc32xx: reparent SIC1 and SIC2 interrupts from MIC")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
NXP LPC32xx keypad controller requires a clock property to be defined.
The change fixes the driver initialization problem:
lpc32xx_keys 40050000.key: failed to get clock
lpc32xx_keys: probe of 40050000.key failed with error -2
Fixes: 93898eb775 ("arm: dts: lpc32xx: add clock properties to device nodes")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Add support for MYIR Tech MYD-LPC4357 Development Board and
MY-LCD70TP-C 7" TFT LCD module with Innolux AT070TN82 panel.
The board contains quite rich periferals, the list features
NXP LPC4357 SoC, 32 MB SDRAM, 4 MB SPI Flash, audio input/output
interface, LCD panel, micro SD card slot, USB, USB OTG, Ethernet,
2 CAN ports, 4 UARTs, I2C and SPI interfaces routed to external
interface.
More information can be found on http://www.myirtech.com/list.asp?id=422
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix
the following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[vzapolskiy: fixed commit message to pass checkpatch.pl test]
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Phytec phyCORE-LPC3250 board is equipped with a Sharp LQ035Q7DB03
3.5" QVGA TFT panel, enable simple panel device driver to get it
supported in the kernel image by default.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Shared buffer allocation is usually done in cell increments.
Drivers will either round up the allocation or refuse the
configuration if it's not an exact multiple of cell size.
Drivers know exactly the cell size of shared buffer, so help
out users by providing this information in dumps.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed voltage regulators are found on Phytec phyCORE-LPC3250 board,
enable the correspondent device driver by default.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Broadcom STB chips support a deep sleep mode where all register
contents are lost. Because we were stashing the MagicPacket password
into some of these registers a suspend into that deep sleep then a
resumption would not lead to being able to wake-up from MagicPacket with
password again.
Fix this by keeping a software copy of the password and program it
during suspend.
Fixes: 83e82f4c70 ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deepa Dinamani says:
====================
net: y2038-safe socket timestamps
The series introduces new socket timestamps that are
y2038 safe.
The time data types used for the existing socket timestamp
options: SO_TIMESTAMP, SO_TIMESTAMPNS and SO_TIMESTAMPING
are not y2038 safe. The series introduces SO_TIMESTAMP_NEW,
SO_TIMESTAMPNS_NEW and SO_TIMESTAMPING_NEW to replace these.
These new timestamps can be used on all architectures.
The alternative considered was to extend the sys_setsockopt()
by using the flags. We did not receive any strong opinions about
either of the approaches. Hence, this was chosen, as glibc folks
preferred this.
The series does not deal with updating the internal kernel socket
calls like rxrpc to make them y2038 safe. This will be dealt
with separately.
Note that the timestamps behavior already does not match the
man page specific behavior:
SIOCGSTAMP
This ioctl should only be used if the socket option SO_TIMESTAMP
is not set on the socket. Otherwise, it returns the timestamp of
the last packet that was received while SO_TIMESTAMP was not set,
or it fails if no such packet has been received,
(i.e., ioctl(2) returns -1 with errno set to ENOENT).
The recommendation is to update the man page to remove the above statement.
The overview of the socket timestamp series is as below:
1. Delete asm specific socket.h when possible.
2. Support SO/SCM_TIMESTAMP* options only in userspace.
3. Rename current SO/SCM_TIMESTAMP* to SO/SCM_TIMESTAMP*_OLD.
3. Alter socket options so that SOCK_RCVTSTAMPNS does
not rely on SOCK_RCVTSTAMP.
4. Introduce y2038 safe types for socket timestamp.
5. Introduce new y2038 safe socket options SO/SCM_TIMESTAMP*_NEW.
6. Intorduce new y2038 safe socket timeout options.
Changes since v4:
* Fixed the typo in calling sock_get_timeout()
Changes since v3:
* Rebased onto net-next and fixups as per review comments
* Merged the socket timeout series
* Integrated Arnd's patch to simplify compat handling of timeout syscalls
Changes since v2:
* Removed extra functions to reduce diff churn as per code review
Changes since v1:
* Dropped the change to disentangle sock flags
* Renamed sock_timeval to __kernel_sock_timeval
* Updated a few comments
* Added documentation changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SO_RCVTIMEO and SO_SNDTIMEO socket options use struct timeval
as the time format. struct timeval is not y2038 safe.
The subsequent patches in the series add support for new socket
timeout options with _NEW suffix that will use y2038 safe
data structures. Although the existing struct timeval layout
is sufficiently wide to represent timeouts, because of the way
libc will interpret time_t based on user defined flag, these
new flags provide a way of having a structure that is the same
for all architectures consistently.
Rename the existing options with _OLD suffix forms so that the
right option is enabled for userspace applications according
to the architecture and time_t definition of libc.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Cc: ccaulfie@redhat.com
Cc: deller@gmx.de
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: rth@twiddle.net
Cc: cluster-devel@redhat.com
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-alpha@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
With the new y2038 safe timestamping options added, update the
documentation to reflect the changes.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new type is meant to be used as a y2038 safe structure
to be used as part of cmsg data.
Presently the SO_TIMESTAMP socket option uses struct timeval
for timestamps. This is not y2038 safe.
Subsequent patches in the series add new y2038 safe socket
option to be used in the place of SO_TIMESTAMP_OLD.
struct __kernel_sock_timeval will be used as the timestamp
format at that time.
struct __kernel_sock_timeval also maintains the same layout
across 32 bit and 64 bit ABIs.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of y2038 solution, all internal uses of
struct timeval are replaced by struct __kernel_old_timeval
and struct compat_timeval by struct old_timeval32.
Make socket timestamps use these new types.
This is mainly to be able to verify that the kernel build
is y2038 safe when such non y2038 safe types are not
supported anymore.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Cc: isdn@linux-pingi.de
Signed-off-by: David S. Miller <davem@davemloft.net>
struct __kernel_old_timeval is supposed to have the same
layout as struct timeval. But, it was inadvarently missed
that __kernel_suseconds has a different definition for
sparc64.
Provide an asm-specific override that fixes it.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cleanup to prepare for the addition of 64-bit time_t
in O_SNDTIMEO/O_RCVTIMEO. The existing compat handler seems
unnecessarily complex and error-prone, moving it all into the
main setsockopt()/getsockopt() implementation requires half
as much code and is easier to extend.
32-bit user space can now use old_timeval32 on both 32-bit
and 64-bit machines, while 64-bit code can use
__old_kernel_timeval.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compiling rxtimestamp.c generates error messages due to
non-existing declaration for write() library call.
Add missing unistd.h include to provide the declaration and
silence the error.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
{t4/t4_vf}_change_mac() API's were only doing additions to MPS_TCAM.
This will fail, when the number of tcam entries is limited particularly
in vf's.
This fix programs hash region with the mac address, when TCAM
addtion fails for {t4/t4vf}_change_mac(). Since the locally maintained
driver list for hash entries is shared across mac_{sync/unsync}(),
added an extra parameter if_mac to track the address added thorugh
{t4/t4vf}_change_mac()
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella says:
====================
vsock/virtio: fix issues on device hot-unplug
These patches try to handle the hot-unplug of vsock virtio transport device in
a proper way.
Maybe move the vsock_core_init()/vsock_core_exit() functions in the module_init
and module_exit of vsock_virtio_transport module can't be the best way, but the
architecture of vsock_core forces us to this approach for now.
The vsock_core proto_ops expect a valid pointer to the transport device, so we
can't call vsock_core_exit() until there are open sockets.
v2 -> v3:
- Rebased on master
v1 -> v2:
- Fixed commit message of patch 1.
- Added Reviewed-by, Acked-by tags by Stefan
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the virtio transport device disappear, we should reset all
connected sockets in order to inform the users.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio_vsock_remove() invokes the vsock_core_exit() also if there
are opened sockets for the AF_VSOCK protocol family. In this way
the vsock "transport" pointer is set to NULL, triggering the
kernel panic at the first socket activity.
This patch move the vsock_core_init()/vsock_core_exit() in the
virtio_vsock respectively in module_init and module_exit functions,
that cannot be invoked until there are open sockets.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1609699
Reported-by: Yan Fu <yafu@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't drop IGMP packets with a source address of all zeros which are
IGMP proxy reports. This is documented in Section 2.1.1 IGMP
Forwarding Rules of RFC 4541 IGMP and MLD Snooping Switches
Considerations.
Signed-off-by: Edward Chron <echron@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The integrated PHY's of later RTL8168 network chips report the generic
PHYID 0x001cc800 (Realtek OUI, model and revision number both set to
zero) and therefore currently the genphy driver is used.
To be able to use the paged version of e.g. phy_write() we need a
PHY driver with the read_page and write_page callbacks implemented.
So basically make a copy of the genphy driver, just with the
read_page and write_page callbacks being set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 fixes from Thomas Gleixner:
"A few updates for x86:
- Fix an unintended sign extension issue in the fault handling code
- Rename the new resource control config switch so it's less
confusing
- Avoid setting up EFI info in kexec when the EFI runtime is
disabled.
- Fix the microcode version check in the AMD microcode loader so it
only loads higher version numbers and never downgrades
- Set EFER.LME in the 32bit trampoline before returning to long mode
to handle older AMD/KVM behaviour properly.
- Add Darren and Andy as x86/platform reviewers"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/resctrl: Avoid confusion over the new X86_RESCTRL config
x86/kexec: Don't setup EFI info if EFI runtime is not enabled
x86/microcode/amd: Don't falsely trick the late loading mechanism
MAINTAINERS: Add Andy and Darren as arch/x86/platform/ reviewers
x86/fault: Fix sign-extend unintended sign extension
x86/boot/compressed/64: Set EFER.LME=1 in 32-bit trampoline before returning to long mode
x86/cpu: Add Atom Tremont (Jacobsville)
Pull cpu hotplug fixes from Thomas Gleixner:
"Two fixes for the cpu hotplug machinery:
- Replace the overly clever 'SMT disabled by BIOS' detection logic as
it breaks KVM scenarios and prevents speculation control updates
when the Hyperthreads are brought online late after boot.
- Remove a redundant invocation of the speculation control update
function"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu/hotplug: Fix "SMT disabled by BIOS" detection for KVM
x86/speculation: Remove redundant arch_smt_update() invocation
Pull perf fixes from Thomas Gleixner:
"A pile of perf updates:
- Fix broken sanity check in the /proc/sys/kernel/perf_cpu_time_max_percent
write handler
- Cure a perf script crash which caused by an unitinialized data
structure
- Highlight the hottest instruction in perf top and not a random one
- Cure yet another clang issue when building perf python
- Handle topology entries with no CPU correctly in the tools
- Handle perf data which contains both tracepoints and performance
counter entries correctly.
- Add a missing NULL pointer check in perf ordered_events_free()"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf script: Fix crash when processing recorded stat data
perf top: Fix wrong hottest instruction highlighted
perf tools: Handle TOPOLOGY headers with no CPU
perf python: Remove -fstack-clash-protection when building with some clang versions
perf core: Fix perf_proc_update_handler() bug
perf script: Fix crash with printing mixed trace point and other events
perf ordered_events: Fix crash in ordered_events__free
Pull EFI fix from Thomas Gleixner:
"The dump info for the efi page table debugging lacks a terminator
which causes the kernel to crash when the debugfile is read"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm64: Fix debugfs crash by adding a terminator for ptdump marker
-----BEGIN PGP SIGNATURE-----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=E2PP
-----END PGP SIGNATURE-----
Merge tag 'for-5.0-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- regression fix: transaction commit can run away due to delayed ref
waiting heuristic, this is not necessary now because of the proper
reservation mechanism introduced in 5.0
- regression fix: potential crash due to use-before-check of an ERR_PTR
return value
- fix for transaction abort during transaction commit that needs to
properly clean up pending block groups
- fix deadlock during b-tree node/leaf splitting, when this happens on
some of the fundamental trees, we must prevent new tree block
allocation to re-enter indirectly via the block group flushing path
- potential memory leak after errors during mount
* tag 'for-5.0-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: On error always free subvol_name in btrfs_mount
btrfs: clean up pending block groups when transaction commit aborts
btrfs: fix potential oops in device_list_add
btrfs: don't end the transaction for delayed refs in throttle
Btrfs: fix deadlock when allocating tree block during leaf/node split
Internal injection testing crashed with a console log that said:
mce: [Hardware Error]: CPU 7: Machine Check Exception: f Bank 0: bd80000000100134
This caused a lot of head scratching because the MCACOD (bits 15:0) of
that status is a signature from an L1 data cache error. But Linux says
that it found it in "Bank 0", which on this model CPU only reports L1
instruction cache errors.
The answer was that Linux doesn't initialize "m->bank" in the case that
it finds a fatal error in the mce_no_way_out() pre-scan of banks. If
this was a local machine check, then this partially initialized struct
mce is being passed to mce_panic().
Fix is simple: just initialize m->bank in the case of a fatal error.
Fixes: 40c36e2741 ("x86/mce: Fix incorrect "Machine check from unknown source" message")
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: x86-ml <x86@kernel.org>
Cc: stable@vger.kernel.org # v4.18 Note pre-v5.0 arch/x86/kernel/cpu/mce/core.c was called arch/x86/kernel/cpu/mcheck/mce.c
Link: https://lkml.kernel.org/r/20190201003341.10638-1-tony.luck@intel.com
Update the error descriptions to match the latest documentation for
easier searching. In some cases the changes are small and in other cases
the changes may be total rewording of the description.
No functional changes.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86@kernel.org
Link: https://lkml.kernel.org/r/20190201225534.8177-5-Yazen.Ghannam@amd.com
Been a busy month, so these are rather later than they should have been.
* atlas-ph-sensor:
- Temperature scale didn't correspond to the ABI.
* axp288:
- A few different fixes around the TS-pin handling.
* ti-ads8688
- Not enough space in the buffer used to build the scan to allow for
the timestamp.
* tools - iio_generic_buffer
- Make num_loops signed so that we really are running for ever
rather than just a long time when we specify -1.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlxV1XIRHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0FogHVA/7BgI+H8bsVf3JpfmCvuptBiz5XREUC3Hr
hN5jNwdMTkH8JkBLYMaC6wCph1x118Fc4UhGFx4NwSg3RfMw6tkDPd+PDI0QY0ii
PUuTIDVMoo7+lKDvanm2yIjdkKwp18fceJRh1peLKBVJ3tQDLD9mJIzi5Ezc9/Y6
Nq+xAv5v5ToE020Znm9oqhuY/lbKNjlcc+RKCy9Q5uFEPDfv2KZzymC/vpuTZ59J
PoE9LRAJoag9/DgI/bskSR3aQbU+ESwKMzCLRvx73P2wZYjfwGFR2G4hCQ3tJbhJ
m87qsnj8TxenLl9VTFvMrYp/c6XEpVp9lugYBlM1GMQV7SHV1DMXSFnnNFm3GHb4
OtubvXD4S/279xlC7JhhH+b6r4TDL3P8rDW1tjmIzUmvczV9rzda+SWj4ea6Ry8d
HtUY9RMrb+w1NEOEEMEYvykVxUS8SpzUVfEJKMKm9OspqjfCpELfVaBrHtomB6//
F6z3oiNzDQPFcqIna/xri7PquFP6zmTmT/2ky+f11sBukukW5y0X/p4laVBHcVmw
D6Au0BmtqB4NOdFcz1zsZNlbCKp3AGveZq5lMS7JQs3VWorJSYEQIQRKrVeSXgE2
hbgLQkai+sVaYL8HSYEf83Mc0dm3/20+PW0oc9tRPysSFYwVIodPJb/1wV0qTKW6
olFtou+Fg/U=
=2R0k
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-5.0a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.0 cycle.
Been a busy month, so these are rather later than they should have been.
* atlas-ph-sensor:
- Temperature scale didn't correspond to the ABI.
* axp288:
- A few different fixes around the TS-pin handling.
* ti-ads8688
- Not enough space in the buffer used to build the scan to allow for
the timestamp.
* tools - iio_generic_buffer
- Make num_loops signed so that we really are running for ever
rather than just a long time when we specify -1.
* tag 'iio-fixes-5.0a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: ti-ads8688: Update buffer allocation for timestamps
tools: iio: iio_generic_buffer: make num_loops signed
iio: adc: axp288: Fix TS-pin handling
iio: chemical: atlas-ph-sensor: correct IIO_TEMP values to millicelsius
The imx-ocotp nvmem driver supports the i.MX 7D SoC too. Allow to select
the imx-ocotp driver even if only the i.MX 7D SoC has been selected.
Fixes: 711d454779 ("nvmem: octop: Add i.MX7D support")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SMCA bank types on future systems will report new error types even
though the bank type is not treated as a new version. These new error
types will reported by bits that are reserved in past systems.
Add the new error descriptions to the lists in edac_mce_amd.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Shirish S <Shirish.S@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190201225534.8177-4-Yazen.Ghannam@amd.com
The existing CS, PSP, and SMU SMCA bank types will see new versions (as
indicated by their McaTypes) in future SMCA systems.
Add the new (HWID, MCATYPE) tuples for these new versions. Reuse the
same names as the older versions, since they are logically the same to
the user. SMCA systems won't mix and match IP blocks with different
McaType versions in the same system, so there isn't a need to
distinguish them. The MCA_IPID register is saved when logging an MCA
error, and that can be used to triage the error.
Also, add the new error descriptions to edac_mce_amd. Some error types
(positions in the list) are overloaded compared to the previous
McaTypes. Therefore, just create new lists of the error descriptions to
keep things simple even if some of the error descriptions are the same
between versions.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Pu Wen <puwen@hygon.cn>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Shirish S <Shirish.S@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190201225534.8177-3-Yazen.Ghannam@amd.com
To avoid compatibility issue with older kernels the firmware doesn't
allow SRQ to work with ODP unless kernel asks for it.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
The device capabilities for ODP structure was missing the field for XRC
transport so add it here.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Move the static keyword around to remove the following warnings (W=1):
arch/powerpc/platforms/ps3/os-area.c:212:1: error: 'static' is not at beginning of declaration [-Werror=old-style-declaration]
arch/powerpc/platforms/ps3/system-bus.c:45:1: error: 'static' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add __cold to the dev_<level> logging functions similar to
the use of __cold in the generic printk function.
Using __cold moves all the dev_<level> logging functions
out-of-line possibly improving code locality and runtime
performance.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is not point in having a trailing semicolon after a closing curly
brace. Remove it.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The following properties:
- regulator-state-enabled
- regulator-state-disabled
- regulator-state-uv
are not valid ones as per
Documentation/devicetree/bindings/regulator/regulator.txt
Fix it by using the correct properties as per the dt bindings.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
