According to the Odroid-C1+ schematics the Ethernet TXD1 signal is
routed to GPIOH_5 and the TXD0 signal is routed to GPIOH_6.
The public S805 datasheet shows that TXD0 can be routed to DIF_2_P and
TXD1 can be routed to DIF_2_N instead.
The pin groups eth_txd0_0 (GPIOH_6) and eth_txd0_1 (DIF_2_P) are both
configured as Ethernet TXD0 and TXD1 data lines in meson8b.dtsi. At the
same time eth_txd1_0 (GPIOH_5) and eth_txd1_1 (DIF_2_N) are configured
as TXD0 and TXD1 data lines as well.
This results in a bad Ethernet receive performance. Presumably this is
due to the eth_txd0 and eth_txd1 signal being routed to the wrong pins.
As a result of that data can only be transmitted on eth_txd2 and
eth_txd3. However, I have no scope to fully confirm this assumption.
The vendor u-boot sources for Odroid-C1 use the following Ethernet
pinmux configuration:
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f);
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000);
This translates to the following pin groups in the mainline kernel:
- register 6 bit 0: eth_rxd1 (DIF_0_P)
- register 6 bit 1: eth_rxd0 (DIF_0_N)
- register 6 bit 2: eth_rx_dv (DIF_1_P)
- register 6 bit 3: eth_rx_clk (DIF_1_N)
- register 6 bit 6: eth_tx_en (DIF_3_P)
- register 6 bit 8: eth_ref_clk (DIF_3_N)
- register 6 bit 9: eth_mdc (DIF_4_P)
- register 6 bit 10: eth_mdio_en (DIF_4_N)
- register 6 bit 11: eth_tx_clk (GPIOH_9)
- register 6 bit 12: eth_txd2 (GPIOH_8)
- register 6 bit 13: eth_txd3 (GPIOH_7)
- register 7 bit 20: eth_txd0_0 (GPIOH_6)
- register 7 bit 21: eth_txd1_0 (GPIOH_5)
- register 7 bit 22: eth_rxd3 (DIF_2_P)
- register 7 bit 23: eth_rxd2 (DIF_2_N)
Drop the eth_txd0_1 and eth_txd1_1 groups from eth_rgmii_pins to fix the
Ethernet transmit performance on Odroid-C1. Also add the eth_rxd2 and
eth_rxd3 groups so we don't rely on the bootloader to set them up.
iperf3 statistics before this change:
- transmitting from Odroid-C1: 741 Mbits/sec (0 retries)
- receiving on Odroid-C1: 199 Mbits/sec (1713 retries)
iperf3 statistics after this change:
- transmitting from Odroid-C1: 667 Mbits/sec (0 retries)
- receiving on Odroid-C1: 750 Mbits/sec (0 retries)
Fixes: b96446541d ("ARM: dts: meson8b: extend ethernet controller description")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Emiliano Ingrassia <ingrassia@epigenesys.com>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Reviewed-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The flag offload_fwd_mark is set as the switch can forward frames by
itself.
This can be considered a fix to a problem introduced in commit
c2e866911e where the port membership are not set in sync. The flag
offload_fwd_mark just needs to be set in tag_ksz.c to prevent the software
bridge from forwarding duplicate multicast frames.
Fixes: c2e866911e ("microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_rx() must be called under a strict contract.
At device dismantle phase, core networking clears IFF_UP
and flush_all_backlogs() is called after rcu grace period
to make sure no incoming packet might be in a cpu backlog
and still referencing the device.
Most drivers call netif_rx() from their interrupt handler,
and since the interrupts are disabled at device dismantle,
netif_rx() does not have to check dev->flags & IFF_UP
Virtual drivers do not have this guarantee, and must
therefore make the check themselves.
Otherwise we risk use-after-free and/or crashes.
Note this patch also fixes a small issue that came
with commit ce6502a8f9 ("vxlan: fix a use after free
in vxlan_encap_bypass"), since the dev->stats.rx_dropped
change was done on the wrong device.
Fixes: d342894c5d ("vxlan: virtual extensible lan")
Fixes: ce6502a8f9 ("vxlan: fix a use after free in vxlan_encap_bypass")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Petr Machata <petrm@mellanox.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netlink has moved from bitmasks to group numbers long ago.
Signed-off-by: Jouke Witteveen <j.witteveen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree support for Plantower PMS7003 particulate matter sensor.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add Plantower to the vendor prefixes.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for Plantower PMS7003 particulate matter sensor.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes warnings reported on linux-next but marking one path
and adding an explicit return in the other.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Andreas Brauchli <a.brauchli@elementarea.net>
Acked-by: Tomasz Duszynski <tduszyns@gmail.com>
__cmpxchg_small erroneously uses u8 for load comparison which can
be either char or short. This patch changes the local variable to
u32 which is sufficiently sized, as the loaded value is already
masked and shifted appropriately. Using an integer size avoids
any unnecessary canonicalization from use of non native widths.
This patch is part of a series that adapts the MIPS small word
atomics code for xchg and cmpxchg on short and char to RISC-V.
Cc: RISC-V Patches <patches@groups.riscv.org>
Cc: Linux RISC-V <linux-riscv@lists.infradead.org>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Signed-off-by: Michael Clark <michaeljclark@mac.com>
[paul.burton@mips.com:
- Fix varialble typo per Jonas Gorski.
- Consolidate load variable with other declarations.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 3ba7f44d2b ("MIPS: cmpxchg: Implement 1 byte & 2 byte cmpxchg()")
Cc: stable@vger.kernel.org # v4.13+
Holding mmap_sem exclusively for a gup() is an overkill. Lets
share the lock and replace the gup call for gup_longterm(), as
it is better suited for the lifetime of the pinning.
Fixes: c0c77d8fb7 ("xsk: add user memory registration support sockopt")
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Bjorn Topel <bjorn.topel@intel.com>
Cc: Magnus Karlsson <magnus.karlsson@intel.com>
CC: netdev@vger.kernel.org
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This is needed by the new MEI-HDCP support in i915, so will need to go
in through drm and drivers-misc trees at least.
-----BEGIN PGP SIGNATURE-----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=IhHa
-----END PGP SIGNATURE-----
Merge tag 'topic/component-typed-2019-02-11' of git://anongit.freedesktop.org/drm/drm-intel into driver-core-next
Daniel writes:
typed componented support + i915/snd-hda changes
This is needed by the new MEI-HDCP support in i915, so will need to go
in through drm and drivers-misc trees at least.
* tag 'topic/component-typed-2019-02-11' of git://anongit.freedesktop.org/drm/drm-intel:
i915/snd_hdac: I915 subcomponent for the snd_hdac
components: multiple components for a device
component: Add documentation
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Out-of-bound access to packet data from the snmp nat helper,
from Jann Horn.
2) ICMP(v6) error packets are set as related traffic by conntrack,
update protocol number before calling nf_nat_ipv4_manip_pkt()
to use ICMP(v6) rather than the original protocol number,
from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When computing maximum size of filesystem possible with given number of
group descriptor blocks, we forget to include s_first_data_block into
the number of blocks. Thus for filesystems with non-zero
s_first_data_block it can happen that computed maximum filesystem size
is actually lower than current filesystem size which confuses the code
and eventually leads to a BUG_ON in ext4_alloc_group_tables() hitting on
flex_gd->count == 0. The problem can be reproduced like:
truncate -s 100g /tmp/image
mkfs.ext4 -b 1024 -E resize=262144 /tmp/image 32768
mount -t ext4 -o loop /tmp/image /mnt
resize2fs /dev/loop0 262145
resize2fs /dev/loop0 300000
Fix the problem by properly including s_first_data_block into the
computed number of filesystem blocks.
Fixes: 1c6bd7173d "ext4: convert file system to meta_bg if needed..."
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
- Fix specification exception on z196 during ap probe
- A fix for suspend-to-disk, the VMAP stack patch broke the
swsusp_arch_suspend function
- The EMC CKD ioctl of the dasd driver needs an additional size
check for user space data
- Revert an incorrect patch for the PCI base code that removed
a bit lock that turned out to be required after all
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJcYRUOAAoJEDjwexyKj9rgsj0H/0podjAiHUMw2F6ccgN6ZULp
g1zqUbRS4AoYX6v/sqMdCczbCSKwQdRR16juLaZHz1tfTP02KkR9KxVLg1/EmNNT
1NqeGVHrStR5MLFES+DNsxmJEVhye82aeT6Mj4NFvsYJvGr68ha90hMzB9ljc6jf
1BFTWgNOea+iQSZix0D9ALbmsoj4cFuSXG+U4N0D4jf+ZPCYLFXUsvsojtMdallS
WIdKTEj2MPMvmC+WpUY91ClkmXf27dmkoz7v/sRMNyW7n62sfmlA+34gRnAO4HVB
1bbIxJ1ss2ZyYtFL5mYI9ikYKsBL+WStmxl5HkhTXl7cdAtwgSbid9gcXqabi7A=
=k0u1
-----END PGP SIGNATURE-----
Merge tag 's390-5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 bug fixes from Martin Schwidefsky:
- Fix specification exception on z196 during ap probe
- A fix for suspend-to-disk, the VMAP stack patch broke the
swsusp_arch_suspend function
- The EMC CKD ioctl of the dasd driver needs an additional size check
for user space data
- Revert an incorrect patch for the PCI base code that removed a bit
lock that turned out to be required after all
* tag 's390-5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
Revert "s390/pci: remove bit_lock usage in interrupt handler"
s390/zcrypt: fix specification exception on z196 during ap probe
s390/dasd: fix using offset into zero size array error
s390/suspend: fix stack setup in swsusp_arch_suspend
Pull alpha fixes from Matt Turner:
"A few changes for alpha, including a build fix, a fix for the Eiger
platform, and a fix for a tricky bug uncovered by the strace test
suite that has existed since at least 1997 (v2.1.32)!"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: fix page fault handling for r16-r18 targets
alpha: Fix Eiger NR_IRQS to 128
tools uapi: fix Alpha support
Refuse to mount a volume read-write without a coherent Logical Volume
Integrity Descriptor, because we can't generate truly unique IDs without
one.
This fixes a bug where all inodes created on a UDF filesystem following
mount without a coherent LVID are assigned unique ID 0 which can then
confuse other UDF implementations.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Fix a grammatical error in the dentry-state text and clarify the usage
of negative dentries.
Fixes: af0c9af1b3 ("fs/dcache: Track & report number of negative dentries")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bio_sectors() returns the value in the units of 512-byte sectors (no
matter what the real sector size of the device). dm-crypt multiplies
bio_sectors() by on_disk_tag_size to calculate the space allocated for
integrity tags. If dm-crypt is running with sector size larger than
512b, it allocates more data than is needed.
Device Mapper trims the extra space when passing the bio to
dm-integrity, so this bug didn't result in any visible misbehavior.
But it must be fixed to avoid wasteful memory allocation for the block
integrity payload.
Fixes: ef43aa3806 ("dm crypt: add cryptographic data integrity protection (authenticated encryption)")
Cc: stable@vger.kernel.org # 4.12+
Reported-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
linear range is suitable for this driver, let's convert it to linear range.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LDO35 uses 25 mV step, not 50 mV. Bucks 7 and 8 use 12.5 mV step
instead of 6.25 mV. Wrong step caused over-voltage (LDO35) or
under-voltage (buck7 and 8) if regulators were used (e.g. on Exynos5420
Arndale Octa board).
Cc: <stable@vger.kernel.org>
Fixes: cb74685ecb ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sander Eikelenboom bisected a NAT related regression down
to the l4proto->manip_pkt indirection removal.
I forgot that ICMP(v6) errors (e.g. PKTTOOBIG) can be set as related
to the existing conntrack entry.
Therefore, when passing the skb to nf_nat_ipv4/6_manip_pkt(), that
ended up calling the wrong l4 manip function, as tuple->dst.protonum
is the original flows l4 protocol (TCP, UDP, etc).
Set the dst protocol field to ICMP(v6), we already have a private copy
of the tuple due to the inversion of src/dst.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Fixes: faec18dbb0 ("netfilter: nat: remove l4proto->manip_pkt")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The generic ASN.1 decoder infrastructure doesn't guarantee that callbacks
will get as much data as they expect; callbacks have to check the `datalen`
parameter before looking at `data`. Make sure that snmp_version() and
snmp_helper() don't read/write beyond the end of the packet data.
(Also move the assignment to `pdata` down below the check to make it clear
that it isn't necessarily a pointer we can use before the `datalen` check.)
Fixes: cc2d58634e ("netfilter: nf_nat_snmp_basic: use asn1 decoder library")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CNL macros for register groups CNL_PORT_TX_DW2_* / CNL_PORT_TX_DW5_* are
configured incorrectly wrt definition of _CNL_PORT_TX_DW_GRP.
v2: Jani suggested to keep the macros organized semantically i.e., by
function, secondarily by port/pipe/transcoder.->(dw, port)
Fixes: 4e53840fdf ("drm/i915/icl: Introduce new macros to get combophy registers")
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190110230844.9213-1-aditya.swarup@intel.com
(cherry picked from commit b14c06ec02)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In August 2018 the BSPEC changed the ICL port programming sequence to
closely resemble earlier gen programming sequence. Restrict combo phy to
HBR max rate unless eDP panel is connected to port.
v2: remove debug code that Imre found
v3: simplify translation table if-else
v4: edp translation table now based on link rate and low_swing
v5: Misc review comments + r-b
BSpec: 21257
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1545084827-5776-1-git-send-email-clinton.a.taylor@intel.com
(cherry picked from commit b265a2a625)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
WCN3990 supports shadow registers write operation support
for copy engine for regular operation in powersave mode.
Since WCN3990 is a 64-bit target, the shadow register
implementation needs to be done in the copy engine handlers
for 64-bit target. Currently the shadow register implementation
is present in the 32-bit target handlers of copy engine.
Fix the shadow register copy engine write operation
implementation for 64-bit target(WCN3990).
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: b7ba83f7c4 ("ath10k: add support for shadow register for WNC3990")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The support to put WCN3990 firmware into Factory
test mode is not present currently. The WCN3990
firmware can operate in Factory test mode based
on the mode it receives in the wlan enable message
from the host driver.
When the host driver is started in testmode send
the operating mode as UTF mode, to the WCN3990
firmware, in the wlan enable message to start the
firmware in Factory test mode.
Tested on: WCN3990
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The DIAG copy engine is only used via polling, but it holds a spinlock
with softirqs disabled. Each iteration of our read/write loops can
theoretically take 20ms (two 10ms timeout loops), and this loop can be
run an unbounded number of times while holding the spinlock -- dependent
on the request size given by the caller.
As of commit 39501ea641 ("ath10k: download firmware via diag Copy
Engine for QCA6174 and QCA9377."), we transfer large chunks of firmware
memory using this mechanism. With large enough firmware segments, this
becomes an exceedingly long period for disabling soft IRQs. For example,
with a 500KiB firmware segment, in testing QCA6174A, I see 200 loop
iterations of about 50-100us each, which can total about 10-20ms.
In reality, we don't really need to block softirqs for this duration.
The DIAG CE is only used in polling mode, and we only need to hold
ce_lock to make sure any CE bookkeeping is done without screwing up
another CE. Otherwise, we only need to ensure exclusion between
ath10k_pci_diag_{read,write}_mem() contexts.
This patch moves to use fine-grained locking for the shared ce_lock,
while adding a new mutex just to ensure mutual exclusion of diag
read/write operations.
Tested on QCA6174A, firmware version WLAN.RM.4.4.1-00132-QCARMSWPZ-1.
Fixes: 39501ea641 ("ath10k: download firmware via diag Copy Engine for QCA6174 and QCA9377.")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW credit flow control is enabled for only WMI ctrl
service(CE3) but credit update is requested unconditionally
on all HTC services as part of HTC tx in CE3/CE0/CE4.
This is causing WOW failure as FW is not expecting credit
report request on other end-points(CE0/CE4).
Request credit report only on those endpoints where
credit flow control is enabled.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wow pause iface config controls the PCI D0/D3-WOW cases for pcie
bus state. Firmware does not expects WOW_IFACE_PAUSE_ENABLED config
for bus/link that cannot be suspended ex:snoc and does not trigger
common subsystem shutdown.
Disable interface pause wow config for integrated chipset(WCN3990)
for correct WOW configuration in the firmware.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register snoc bus layer suspend/resume PM ops and configure
the wakeup source(CE2) for the device.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Many integrated QCA9984 WiFis in various IPQ806x platform routers
from various vendors (Netgear R7800, ZyXEL NBG6817, TP-LINK C2600,
etc.) have either blank, bogus or non-unique MAC-addresses in
their calibration data.
As a result, OpenWrt utilizes a discouraged binary calibration data
patching method that allows to modify the device's MAC-addresses right
at the source. This is because the ath10k' firmware extracts the MAC
address from the supplied radio/calibration data and issues a response
to the ath10k linux driver. Which was designed to take the main MAC in
ath10k_wmi_event_ready().
Part of the "setting an alternate MAC" issue was already tackled by a
patch from Brian Norris:
commit 9d5804662c
("ath10k: retrieve MAC address from system firmware if provided")
by allowing the option to specify an alternate MAC-address with the
established device_get_mac_address() function which extracts the right
address from DeviceTree/fwnode mac-address or local-mac-address
properties and saves it for later.
However, Ben Greear noted that the Qualcomm's ath10k firmware is liable
to not properly calculate its rx-bssid mask in this case. This can cause
issues in the popluar "multiple AP with a single ath10k instance"
configurations.
To improve MAC address handling, Felix Fietkau suggested to call
pdev_set_base_macaddr_cmdid before bringing up the first vif and
use the first vif MAC address there. Which is in ath10k_core_start().
This patch implement Felix Fietkau's request to
"call pdev_set_base_macaddr_cmdid before bringing up the first vif".
The pdev_set_base_macaddr_cmdid is already declared for all devices
and version. The driver just needed the support code for this
function.
Tested on:
QCA9880/CUS223, firmwares: 10.2.4.13-2, 10.2.4.70.44, 10.2.4-1.0-00041
QCA9887/MR33 firmware:10.2.4-1.0-00033
QCA4019/RT-AC58U firmware: 10.4-3.4-00104, 10.4-3.5.3-00057
QCA9984/R7800 firmware: Candela Technologies (CT) Firmware
BugLink: https://lists.openwrt.org/pipermail/openwrt-devel/2018-November/014595.html
Fixes: 9d5804662c ("ath10k: retrieve MAC address from system firmware if provided")
Cc: Brian Norris <briannorris@chromium.org>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TLV based firmware ex. QCA6174, WCN3990 expects key cipher value
set to 9 while non-TLV firmware expects key cipher value set to 8
for enabling GCMP and GCMP-256 cipher suites.
To fix this problem, attach the key cipher suite values based on
wmi version.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hostapd uses CCMP, GCMP & GCMP-256 as 'wpa_pairwise' option to run WPA3.
In WCN3990 firmware cipher suite numbers 9 to 11 are for CCMP,
GCMP & GCMP-256.
To enable CCMP, GCMP & GCMP-256 cipher suites in WCN3990 firmware,
host sets 'n_cipher_suites = 11' while initializing hardware parameters.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
REGULATORY_WIPHY_SELF_MANAGED as set here breaks NL80211_CMD_GET_REG,
because it expects the wiphy to do regulatory management. Since
virt_wifi does not do regulatory management, this triggers a WARN_ON in
NL80211_CMD_GET_REG and fails the netlink command.
Removing REGULATORY_WIPHY_SELF_MANAGED fixes the problem and the virtual
wireless network continues to work.
Signed-off-by: Cody Schuffelen <schuffelen@google.com>
Acked-by: Alistair Strachan <astrachan@google.com>
Acked-by: Greg Hartman <ghartman@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For correct operation of the digital filtering and other processing on the
WM8741, the user must ensure the correct value of OSR[1:0] is set at all
times.[1] Hence, depending the selected sampling rate, set the OSR (over-
sampling rate) mode in hw_params().
References:
[1] "WM8741 Data Sheet"
Signed-off-by: Sergej Sawazki <sergej@taudac.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sergej Sawazki <sergej@taudac.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BE dai links only have internal PCM's and their substream ops may
not be set. Suspending these PCM's will result in their
ops->trigger() being invoked and cause a kernel oops.
So skip suspending PCM's if their ops are NULL.
[ NOTE: this change is required now for following the recent PCM core
change to get rid of snd_pcm_suspend() call. Since DPCM BE takes
the runtime carried from FE while keeping NULL ops, it can hit this
bug. See details at:
https://github.com/thesofproject/linux/pull/582
-- tiwai ]
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Loading/unloading modules exposes issues with memory allocation, which
is a mix of devm_kzalloc and manual kzalloc. Move to devm_k routines
everywhere to simplify all this.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ADC and DAC can be clocked from separate or same sources CLK1 and CLK2.
By default, ADC is clocked from CLK1, and DAC - from CLK2.
This commits allows sound cards to selest a proper clock source during
`hw_params()` via `snd_soc_dai_set_sysclk()`. It makes possible to have a
single clock source for both ADC and DAC.
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
Softly reset registers values on module probe
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix cfg80211_gen_new_bssid() to not rely on u64 modulo arithmetic,
which isn't needed since we really just want to mask there. Also,
clean it up to calculate the mask only once and use GENMASK_ULL()
instead of open-coding the mask calculation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enforce the first argument to be a correct type of a pointer to struct
element and avoid unnecessary typecasts from const to non-const pointers
(the change in validate_ie_attr() is needed to make this part work). In
addition, avoid signed/unsigned comparison within for_each_element() and
mark struct element packed just in case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It clarifies that the DMA description pointer returned by
`dmaengine_prep_*` function should not be used after submission.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Implement --affinity=node|cpu option for the record mode defaulting
to system affinity mask bouncing.
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/083f5422-ece9-10dd-8305-bf59c860f10f@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
As can be seen by clicking around the timeline on web.archive.org[1],
there were no -git patches/tarballs on kernel.org since release 3.1.
[1]: https://web.archive.org/web/20111103073843/http://www.kernel.org/
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
