When a link endpoint is re-created (e.g. after a node reboot or
interface reset), the link session number is varied by random, the peer
endpoint will be synced with this new session number before the link is
re-established.
However, there is a shortcoming in this mechanism that can lead to the
link never re-established or faced with a failure then. It happens when
the peer endpoint is ready in ESTABLISHING state, the 'peer_session' as
well as the 'in_session' flag have been set, but suddenly this link
endpoint leaves. When it comes back with a random session number, there
are two situations possible:
1/ If the random session number is larger than (or equal to) the
previous one, the peer endpoint will be updated with this new session
upon receipt of a RESET_MSG from this endpoint, and the link can be re-
established as normal. Otherwise, all the RESET_MSGs from this endpoint
will be rejected by the peer. In turn, when this link endpoint receives
one ACTIVATE_MSG from the peer, it will move to ESTABLISHED and start
to send STATE_MSGs, but again these messages will be dropped by the
peer due to wrong session.
The peer link endpoint can still become ESTABLISHED after receiving a
traffic message from this endpoint (e.g. a BCAST_PROTOCOL or
NAME_DISTRIBUTOR), but since all the STATE_MSGs are invalid, the link
will be forced down sooner or later!
Even in case the random session number is larger than the previous one,
it can be that the ACTIVATE_MSG from the peer arrives first, and this
link endpoint moves quickly to ESTABLISHED without sending out any
RESET_MSG yet. Consequently, the peer link will not be updated with the
new session number, and the same link failure scenario as above will
happen.
2/ Another situation can be that, the peer link endpoint was reset due
to any reasons in the meantime, its link state was set to RESET from
ESTABLISHING but still in session, i.e. the 'in_session' flag is not
reset...
Now, if the random session number from this endpoint is less than the
previous one, all the RESET_MSGs from this endpoint will be rejected by
the peer. In the other direction, when this link endpoint receives a
RESET_MSG from the peer, it moves to ESTABLISHING and starts to send
ACTIVATE_MSGs, but all these messages will be rejected by the peer too.
As a result, the link cannot be re-established but gets stuck with this
link endpoint in state ESTABLISHING and the peer in RESET!
Solution:
===========
This link endpoint should not go directly to ESTABLISHED when getting
ACTIVATE_MSG from the peer which may belong to the old session if the
link was re-created. To ensure the session to be correct before the
link is re-established, the peer endpoint in ESTABLISHING state will
send back the last session number in ACTIVATE_MSG for a verification at
this endpoint. Then, if needed, a new and more appropriate session
number will be regenerated to force a re-synch first.
In addition, when a link in ESTABLISHING state is reset, its state will
move to RESET according to the link FSM, along with resetting the
'in_session' flag (and the other data) as a normal link reset, it will
also be deleted if requested.
The solution is backward compatible.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
devlink: minor tweaks to reported device info
This series contains two minor touch ups for devlink code. First
|| is corrected to && in the ethtool compat code. Next patch
decreases the stack allocation size.
On the nfp side after further discussions with the manufacturing
team we decided to realign the serial number contents slightly and
rename one of the other fields from "vendor" to "mfr", short for
"manufacture".
v2: - add patch 3 - move board maker as a generic attribute.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The manufacturing team requests we include vendor and product
in the serial number field, as the serial number itself is not
unique across manufacturing facilities and products.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vendor may sound ambiguous, let's rename the fab string to
"board.manufacture" (which was just added as a generic identifier).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At Jiri's suggestion add a generic "board.manufacture"
version identifier.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of devlink attributes has grown over 128, causing the
following warning:
../net/core/devlink.c: In function ‘devlink_nl_cmd_region_read_dumpit’:
../net/core/devlink.c:3740:1: warning: the frame size of 1064 bytes is larger than 1024 bytes [-Wframe-larger-than=]
}
^
Since the number of attributes is only going to grow allocate
the array dynamically.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need the port to be both ethernet and have the rigth netdev,
not one or the other.
Fixes: ddb6e99e2d ("ethtool: add compat for devlink info")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow those steps:
# ip addr add 2001:123::1/32 dev eth0
# ip addr add 2001:123:456::2/64 dev eth0
# ip addr del 2001:123::1/32 dev eth0
# ip addr del 2001:123:456::2/64 dev eth0
and then prefix route of 2001:123::1/32 will still exist.
This is because ipv6_prefix_equal in check_cleanup_prefix_route
func does not check whether two IPv6 addresses have the same
prefix length. If the prefix of one address starts with another
shorter address prefix, even though their prefix lengths are
different, the return value of ipv6_prefix_equal is true.
Here I add a check of whether two addresses have the same prefix
to decide whether their prefixes are equal.
Fixes: 5b84efecb7 ("ipv6 addrconf: don't cleanup prefix route for IFA_F_NOPREFIXROUTE")
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reported-by: Wenhao Zhang <zhangwenhao8@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiong Wang says:
====================
This set improves bpf object file related rules in selftests Makefile.
- tell git to ignore the build dir "alu32".
- extend sub-register mode compilation to all bpf object files to give
LLVM compiler bpf back-end more exercise.
- auto-generate bpf kernel object file list.
- relax sub-register mode compilation criteria.
v1 -> v2:
- rename "kern_progs" to "progs". (Alexei)
- spin a new patch to remove build server kernel requirement for
sub-register mode compilation (Alexei)
- rebase on top of KaFai’s latest "test_sock_fields" patch set.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Sub-register mode compilation was enabled only when there are eBPF "v3"
processor supports at both compilation time inside LLVM and runtime inside
kernel.
Given separation betwen build and test server could be often, this patch
removes the runtime support criteria.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
At the moment, all kernel bpf objects are listed under BPF_OBJ_FILES.
Listing them manually sometimes causing patch conflict when people are
adding new testcases simultaneously.
It is better to centre all the related source files under a subdir
"progs", then auto-generate the object file list.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
At the moment, we only do extra sub-register mode compilation on bpf object
files used by "test_progs". These object files are really loaded and
executed.
This patch further extends sub-register mode compilation to all bpf object
files, even those without corresponding runtime tests. Because this could
help testing LLVM sub-register code-gen, kernel bpf selftest has much more
C testcases with reasonable size and complexity compared with LLVM
testsuite which only contains unit tests.
There were some file duplication inside BPF_OBJ_FILES_DUAL_COMPILE which
is removed now.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
"alu32" is a build dir and contains various files for BPF sub-register
code-gen testing.
This patch tells git to ignore it.
Suggested-by: Yonghong Song <yhs@fb.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When requeue, if RQF_DONTPREP, rq has contained some driver
specific data, so insert it to hctx dispatch list to avoid any
merge. Take scsi as example, here is the trace event log (no
io scheduler, because RQF_STARTED would prevent merging),
kworker/0:1H-339 [000] ...1 2037.209289: block_rq_insert: 8,0 R 4096 () 32768 + 8 [kworker/0:1H]
scsi_inert_test-1987 [000] .... 2037.220465: block_bio_queue: 8,0 R 32776 + 8 [scsi_inert_test]
scsi_inert_test-1987 [000] ...2 2037.220466: block_bio_backmerge: 8,0 R 32776 + 8 [scsi_inert_test]
kworker/0:1H-339 [000] .... 2047.220913: block_rq_issue: 8,0 R 8192 () 32768 + 16 [kworker/0:1H]
scsi_inert_test-1996 [000] ..s1 2047.221007: block_rq_complete: 8,0 R () 32768 + 8 [0]
scsi_inert_test-1996 [000] .Ns1 2047.221045: block_rq_requeue: 8,0 R () 32776 + 8 [0]
kworker/0:1H-339 [000] ...1 2047.221054: block_rq_insert: 8,0 R 4096 () 32776 + 8 [kworker/0:1H]
kworker/0:1H-339 [000] ...1 2047.221056: block_rq_issue: 8,0 R 4096 () 32776 + 8 [kworker/0:1H]
scsi_inert_test-1986 [000] ..s1 2047.221119: block_rq_complete: 8,0 R () 32776 + 8 [0]
(32768 + 8) was requeued by scsi_queue_insert and had RQF_DONTPREP.
Then it was merged with (32776 + 8) and issued. Due to RQF_DONTPREP,
the sdb only contained the part of (32768 + 8), then only that part
was completed. The lucky thing was that scsi_io_completion detected
it and requeued the remaining part. So we didn't get corrupted data.
However, the requeue of (32776 + 8) is not expected.
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When we free skb at tipc_data_input, we return a 'false' boolean.
Then, skb passed to subcalling tipc_link_input in tipc_link_rcv,
<snip>
1303 int tipc_link_rcv:
...
1354 if (!tipc_data_input(l, skb, l->inputq))
1355 rc |= tipc_link_input(l, skb, l->inputq);
</snip>
Fix it by simple changing to a 'true' boolean when skb is being free-ed.
Then, tipc_link_rcv will bypassed to subcalling tipc_link_input as above
condition.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <maloy@donjonn.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The v5 superblock format added various metadata fields (such as crc,
metadata lsn, owner uuid, etc.) to v4 metadata headers or created
new v5 headers for blocks where no such headers existed on v4. Where
v4 headers did exist, the v5 structures are careful to place v4
metadata at the original location. For example, the magic value is
expected to be at the same location in certain blocks to facilitate
version detection.
While failure of this invariant is likely to cause severe and
obvious problems at runtime, we can detect this condition at compile
time via the more recently added on-disk format check
infrastructure. Since there is no runtime cost, add some offset
checks that start with v5 structure definitions, traverse down to
the first bit of common metadata with v4 and ensure that common
metadata is at the expected offset. Note that we don't care about
blocks which had no v4 header because there is no common metadata in
those cases. No functional changes.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Now that we encode block magic numbers in all the buffer ops, use that
for block type detection in the ag header repair code instead of
encoding magics directly in the repair code.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Add dquot magic numbers to the buffer ops type, in case we ever want to
use them.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Use xfs_verify_magic to check the magic numbers of inodes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
With the verifier magic value helper in place, we've left a bit more
duplicate code across the verifiers that involve struct
xfs_da3_blkinfo. This includes the da node, xattr leaf and dir leaf
verifiers, all of which perform similar checks for v4 and v5
filesystems.
Create a common helper to verify an xfs_da3_blkinfo structure,
taking care to only access v5 fields where appropriate, and refactor
the aforementioned verifiers to use the helper. No functional
changes.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Most buffer verifiers have hardcoded magic value checks
conditionalized on the version of the filesystem. The magic value
field of the verifier structure facilitates abstraction of some of
this code. Populate the ->magic field of various verifiers to take
advantage of this abstraction. No functional changes.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The dir2 leaf verifiers share the same underlying structure
verification code, but implement six accessor functions to multiplex
the code across the two verifiers. Further, the magic value isn't
sufficiently abstracted such that the common helper has to manually
fix up the magic from the caller on v5 filesystems.
Use the magic field in the verifier structure to eliminate the
duplicate code and clean this all up. No functional change.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The allocation btree verifiers share code that is unable to detect
cross-tree magic value corruptions such as a bnobt block with a
cntbt magic value. Populate the b_ops->magic field of the associated
verifier structures such that the structure verifier can check the
magic value against the expected value based on tree type.
The btree level check requires knowledge of the tree type to
determine the appropriate maximum value. This was previously part of
the hardcoded magic value checks. With that code removed, peek at
the first magic value in the verifier to determine the expected tree
type of the current block.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Similar to the inode btree verifier, the same allocation btree
verifier structure is shared between the by-bno (bnobt) and by-size
(cntbt) btrees. This prevents the ability to distinguish magic
values between them. Separate the verifier into two, one for each
tree, and assign them appropriately. No functional changes.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The inode btree verifier code is shared between the inode btree and
free inode btree because the underlying metadata formats are
essentially equivalent. A side effect of this is that the verifier
cannot determine whether a particular btree block should have an
inobt or finobt magic value.
This logic allows an unfortunate xfs_repair bug to escape detection
where certain level > 0 nodes of the finobt are stamped with inobt
magic by xfs_repair finobt reconstruction. This is fortunately not a
severe problem since the inode btree magic values do not contribute
to any changes in kernel behavior, but we do need a means to detect
and prevent this problem in the future.
Add a field to xfs_buf_ops to store the v4 and v5 superblock magic
values expected by a particular verifier. Add a helper to check an
on-disk magic value against the value expected by the verifier. Call
the helper from the shared [f]inobt verifier code for magic value
verification. This ensures that the inode btree blocks each have the
appropriate magic value based on specific tree type and superblock
version.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The inobt verifier is reused for the inobt and finobt, which
prevents the ability to distinguish between magic values on a
per-tree basis. Create a separate finobt structure in preparation
for changes to enforce the appropriate magic value for the
associated tree. This patch has no functional change.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Most verifiers that check on-disk magic values convert the CPU
endian magic value constant to disk endian to facilitate compile
time optimization of the byte swap and reduce the need for runtime
byte swaps in buffer verifiers. Several buffer verifiers do not
follow this pattern. Update those verifiers for consistency.
Also fix up a random typo in the inode readahead verifier name.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Improve the documentation around xfs_buf_ensure_ops, which is the
function that is responsible for cleaning up the b_ops state of buffers
that go through xrep_findroot_block but don't match anything. Rename
the function to xfs_buf_reverify.
[darrick: this started off as bfoster mods of a previous patch of mine,
but the renaming part is now this separate patch.]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Use a rhashtable to cache the unlinked list incore. This should speed
up unlinked processing considerably when there are a lot of inodes on
the unlinked list because iunlink_remove no longer has to traverse an
entire bucket list to find which inode points to the one being removed.
The incore list structure records "X.next_unlinked = Y" relations, with
the rhashtable using Y to index the records. This makes finding the
inode X that points to a inode Y very quick. If our cache fails to find
anything we can always fall back on the old method.
FWIW this drastically reduces the amount of time it takes to remove
inodes from the unlinked list. I wrote a program to open a lot of
O_TMPFILE files and then close them in the same order, which takes
a very long time if we have to traverse the unlinked lists. With the
ptach, I see:
+ /d/t/tmpfile/tmpfile
Opened 193531 files in 6.33s.
Closed 193531 files in 5.86s
real 0m12.192s
user 0m0.064s
sys 0m11.619s
+ cd /
+ umount /mnt
real 0m0.050s
user 0m0.004s
sys 0m0.030s
And without the patch:
+ /d/t/tmpfile/tmpfile
Opened 193588 files in 6.35s.
Closed 193588 files in 751.61s
real 12m38.853s
user 0m0.084s
sys 12m34.470s
+ cd /
+ umount /mnt
real 0m0.086s
user 0m0.000s
sys 0m0.060s
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Add tracepoints so we can associate high level operations with low level
updates. No functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
In xfs_iunlink_remove we have two identical calls to
xfs_iunlink_update_inode, so move it out of the if statement to simplify
the code some more.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
There's a loop that searches an unlinked bucket list to find the inode
that points to a given inode. Hoist this into a separate function;
later we'll use our iunlink backref cache to bypass the slow list
operation. No functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Hoist the functions that update an inode's unlinked pointer updates into
a helper. No functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Strengthen our checking of the AGI unlinked pointers when we start to
use them for updating the metadata.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Split the AGI unlinked bucket updates into a separate function. No
functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Add a new helper to check that a per-AG inode pointer is either null or
points somewhere valid within that AG.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fix some indentation issues with the iunlink functions and reorganize
the tops of the functions to be identical. No functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The writeback delalloc conversion code is racy with respect to
changes in the currently cached file mapping outside of the current
page. This is because the ilock is cycled between the time the
caller originally looked up the mapping and across each real
allocation of the provided file range. This code has collected
various hacks over the years to help combat the symptoms of these
races (i.e., truncate race detection, allocation into hole
detection, etc.), but none address the fundamental problem that the
imap may not be valid at allocation time.
Rather than continue to use race detection hacks, update writeback
delalloc conversion to a model that explicitly converts the delalloc
extent backing the current file offset being processed. The current
file offset is the only block we can trust to remain once the ilock
is dropped because any operation that can remove the block
(truncate, hole punch, etc.) must flush and discard pagecache pages
first.
Modify xfs_iomap_write_allocate() to use the xfs_bmapi_delalloc()
mechanism to request allocation of the entire delalloc extent
backing the current offset instead of assuming the extent passed by
the caller is unchanged. Record the range specified by the caller
and apply it to the resulting allocated extent so previous checks by
the caller for COW fork overlap are not lost. Finally, overload the
bmapi delalloc flag with the range reval flag behavior since this is
the only use case for both.
This ensures that writeback always picks up the correct
and current extent associated with the page, regardless of races
with other extent modifying operations. If operating on a data fork
and the COW overlap state has changed since the ilock was cycled,
the caller revalidates against the COW fork sequence number before
using the imap for the next block.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The writeback delalloc conversion code is racy with respect to
changes in the currently cached file mapping. This stems from the
fact that the bmapi allocation code requires a file range to
allocate and the writeback conversion code assumes the range of the
currently cached mapping is still valid with respect to the fork. It
may not be valid, however, because the ilock is cycled (potentially
multiple times) between the time the cached mapping was populated
and the delalloc conversion occurs.
To facilitate a solution to this problem, create a new
xfs_bmapi_delalloc() wrapper to xfs_bmapi_write() that takes a file
(FSB) offset and attempts to allocate whatever delalloc extent backs
the offset. Use a new bmapi flag to cause xfs_bmapi_write() to set
the range based on the extent backing the bno parameter unless bno
lands in a hole. If bno does land in a hole, fall back to the
current behavior (which may result in an error or quietly skipping
holes in the specified range depending on other parameters). This
patch does not change behavior.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Now that the cached writeback mapping is explicitly invalidated on
data fork changes, the EOF trimming band-aid is no longer necessary.
Remove xfs_trim_extent_eof() as well since it has no other users.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The writeback code caches the current extent mapping across multiple
xfs_do_writepage() calls to avoid repeated lookups for sequential
pages backed by the same extent. This is known to be slightly racy
with extent fork changes in certain difficult to reproduce
scenarios. The cached extent is trimmed to within EOF to help avoid
the most common vector for this problem via speculative
preallocation management, but this is a band-aid that does not
address the fundamental problem.
Now that we have an xfs_ifork sequence counter mechanism used to
facilitate COW writeback, we can use the same mechanism to validate
consistency between the data fork and cached writeback mappings. On
its face, this is somewhat of a big hammer approach because any
change to the data fork invalidates any mapping currently cached by
a writeback in progress regardless of whether the data fork change
overlaps with the range under writeback. In practice, however, the
impact of this approach is minimal in most cases.
First, data fork changes (delayed allocations) caused by sustained
sequential buffered writes are amortized across speculative
preallocations. This means that a cached mapping won't be
invalidated by each buffered write of a common file copy workload,
but rather only on less frequent allocation events. Second, the
extent tree is always entirely in-core so an additional lookup of a
usable extent mostly costs a shared ilock cycle and in-memory tree
lookup. This means that a cached mapping reval is relatively cheap
compared to the I/O itself. Third, spurious invalidations don't
impact ioend construction. This means that even if the same extent
is revalidated multiple times across multiple writepage instances,
we still construct and submit the same size ioend (and bio) if the
blocks are physically contiguous.
Update struct xfs_writepage_ctx with a new field to hold the
sequence number of the data fork associated with the currently
cached mapping. Check the wpc seqno against the data fork when the
mapping is validated and reestablish the mapping whenever the fork
has changed since the mapping was cached. This ensures that
writeback always uses a valid extent mapping and thus prevents lost
writebacks and stale delalloc block problems.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Allison Henderson <allison.henderson@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The sequence counter in the xfs_ifork structure is only updated on
COW forks. This is because the counter is currently only used to
optimize out repetitive COW fork checks at writeback time.
Tweak the extent code to update the seq counter regardless of the
fork type in preparation for using this counter on data forks as
well.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Allison Henderson <allison.henderson@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Currently we have a few PTAGs in place allowing us to transform a filesystem
error in a BUG() call. However, we don't have a panic tag for corrupt
metadata, so introduce XFS_PTAG_VERIFIER_ERROR so that the administrator can
use the fs.xfs.panic_mask sysctl knob to convert any error detected by buffer
verifiers into a kernel panic.
Signed-off-by: Marco Benatto <mbenatto@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
[darrick: light editing of commit message]
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Check extended attribute entry names for invalid characters.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Check directory entry names for invalid characters.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Fix an off-by-one error in the realtime bitmap "is used" cross-reference
helper function if the realtime extent size is a single block.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Teach scrub to flag extent maps that exceed the range that can be mapped
with a xfs_dablk_t.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
The extended attribute scrubber should abort the "read all attrs" loop
if there's a fatal signal pending on the process.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Move all the confusing dinode mapping code that's split between
xchk_iallocbt_check_cluster and xchk_iallocbt_check_cluster_ifree into
the first function so that it's clearer how we find the dinode for a
given inode.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
