The CXL.mem protocol allows a device to act as a provider of "System
RAM" and/or "Persistent Memory" that is fully coherent as if the memory
was attached to the typical CPU memory controller.
With the CXL-2.0 specification a PCI endpoint can implement a "Type-3"
device interface and give the operating system control over "Host
Managed Device Memory". See section 2.3 Type 3 CXL Device.
The memory range exported by the device may optionally be described by
the platform firmware memory map, or by infrastructure like LIBNVDIMM to
provision persistent memory capacity from one, or more, CXL.mem devices.
A pre-requisite for Linux-managed memory-capacity provisioning is this
cxl_mem driver that can speak the mailbox protocol defined in section
8.2.8.4 Mailbox Registers.
For now just land the initial driver boiler-plate and Documentation/
infrastructure.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: David Rientjes <rientjes@google.com> (v1)
Cc: Jonathan Corbet <corbet@lwn.net>
Link: https://www.computeexpresslink.org/download-the-specification
Link: https://lore.kernel.org/r/20210217040958.1354670-2-ben.widawsky@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
All drivers return 0 in their remove callback and the driver core ignores
the return value of nvdimm_bus_remove() anyhow. So simplify by changing
the driver remove callback to return void and return 0 unconditionally
to the upper layer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210212171043.2136580-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add a flag and helper function to indicate that a PHY device is part of
an SFP module, which is set on attach. This can be used by PHY drivers
to handle SFP-specific quirks or behavior.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
pull-request: mlx5-next 2021-02-16
The patches in this pr are already submitted and reviewed through the
netdev and rdma mailing lists.
The series includes mlx5 HW bits and definitions for mlx5 real time clock
translation and handling in the mlx5 driver clock module to enable and
support such mode [1]
[1] https://patchwork.kernel.org/project/netdevbpf/patch/20210212223042.449816-7-saeed@kernel.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support for MRP. The HW will just trap all MRP frames on the
ring ports to CPU and allow the SW to process them. In this way it is
possible to for this node to behave both as MRM and MRC.
Current limitations are:
- it doesn't support Interconnect roles.
- it supports only a single ring.
- the HW should be able to do forwarding of MRP Test frames so the SW
will not need to do this. So it would be able to have the role MRC
without SW support.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver tried to communicate towards the PHY driver whether it
wanted RGMII in-band signaling enabled or disabled however there is
nothing that looks at those flags in drivers/net/phy/broadcom.c so this
does do not anything.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal timer mode (SW clock) requires some PTP clock related metadata
structs. Real time mode (HW clock) will not need these metadata structs.
This separation emphasize the different interfaces for HW clock and SW
clock.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add needed structure layouts and defines for MTUTC (Management UTC)
register. MTUTC will be used for cyc2time HW translation.
In addition, add cyc2time modify capability bit and init segment HCA
real time address.
Finally, add capability bits indicating which time-stamping format is
supported per SQ and RQ. Add ts_format in the queue's context layout to
allow configuration.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-02-16
The following pull-request contains BPF updates for your *net-next* tree.
There's a small merge conflict between 7eeba1706e ("tcp: Add receive timestamp
support for receive zerocopy.") from net-next tree and 9cacf81f81 ("bpf: Remove
extra lock_sock for TCP_ZEROCOPY_RECEIVE") from bpf-next tree. Resolve as follows:
[...]
lock_sock(sk);
err = tcp_zerocopy_receive(sk, &zc, &tss);
err = BPF_CGROUP_RUN_PROG_GETSOCKOPT_KERN(sk, level, optname,
&zc, &len, err);
release_sock(sk);
[...]
We've added 116 non-merge commits during the last 27 day(s) which contain
a total of 156 files changed, 5662 insertions(+), 1489 deletions(-).
The main changes are:
1) Adds support of pointers to types with known size among global function
args to overcome the limit on max # of allowed args, from Dmitrii Banshchikov.
2) Add bpf_iter for task_vma which can be used to generate information similar
to /proc/pid/maps, from Song Liu.
3) Enable bpf_{g,s}etsockopt() from all sock_addr related program hooks. Allow
rewriting bind user ports from BPF side below the ip_unprivileged_port_start
range, both from Stanislav Fomichev.
4) Prevent recursion on fentry/fexit & sleepable programs and allow map-in-map
as well as per-cpu maps for the latter, from Alexei Starovoitov.
5) Add selftest script to run BPF CI locally. Also enable BPF ringbuffer
for sleepable programs, both from KP Singh.
6) Extend verifier to enable variable offset read/write access to the BPF
program stack, from Andrei Matei.
7) Improve tc & XDP MTU handling and add a new bpf_check_mtu() helper to
query device MTU from programs, from Jesper Dangaard Brouer.
8) Allow bpf_get_socket_cookie() helper also be called from [sleepable] BPF
tracing programs, from Florent Revest.
9) Extend x86 JIT to pad JMPs with NOPs for helping image to converge when
otherwise too many passes are required, from Gary Lin.
10) Verifier fixes on atomics with BPF_FETCH as well as function-by-function
verification both related to zero-extension handling, from Ilya Leoshkevich.
11) Better kernel build integration of resolve_btfids tool, from Jiri Olsa.
12) Batch of AF_XDP selftest cleanups and small performance improvement
for libbpf's xsk map redirect for newer kernels, from Björn Töpel.
13) Follow-up BPF doc and verifier improvements around atomics with
BPF_FETCH, from Brendan Jackman.
14) Permit zero-sized data sections e.g. if ELF .rodata section contains
read-only data from local variables, from Yonghong Song.
15) veth driver skb bulk-allocation for ndo_xdp_xmit, from Lorenzo Bianconi.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Support eager writing to the server, meaning that we write the data to
cache on the server, and wait for that to complete. This ensures that we
see ENOSPC errors immediately.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The mount flags are all unsigned integers, so we should not be storing
them in a signed field.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Leon Romanovsky says:
====================
Add an extra timestamp format for mlx5_ib device.
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
due to dependencies.
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
* branch 'mlx5_timestamp':
RDMA/mlx5: Fail QP creation if the device can not support the CQE TS
net/mlx5: Add new timestamp mode bits
The traditional DevX CQ creation flow goes through mlx5_core_create_cq()
which checks that the given EQN corresponds to an existing EQ and attaches
a devx handler to the EQN for the CQ.
In some cases the EQ will not be a kernel EQ, but will be controlled by
modify CQ, don't block creating these just because the EQN can't be found
in the kernel.
Link: https://lore.kernel.org/r/20210211085549.1277674-1-leon@kernel.org
Signed-off-by: Tal Gilboa <talgi@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Use a counter to keep track of how many requests are queued behind the
xprt->xpt_mutex, and keep TCP_CORK set until the queue is empty.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Link: https://lore.kernel.org/linux-nfs/20210213202532.23146-1-trondmy@kernel.org/T/#u
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
These fields declare which timestamp mode is supported by the device
per RQ/SQ/QP.
In addition add the ts_format field to the select the mode for
RQ/SQ/QP.
Link: https://lore.kernel.org/r/20210209131107.698833-2-leon@kernel.org
Signed-off-by: Aharon Landau <aharonl@nvidia.com>
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
These options were introduced in 3.19 with support for message signing
and are rather useless, as explained in commit a51983e4dd ("libceph:
add nocephx_sign_messages option"). Deprecate them.
In case there is someone out there with a cluster that lacks support
for MSG_AUTH feature (very unlikely but has to be considered since we
haven't formally raised the bar from argonaut to bobtail yet), make
nocephx_sign_messages also waive MSG_AUTH requirement. This is probably
how it should have been done in the first place -- if we aren't going
to sign, requiring the signing feature makes no sense.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Userspace has discovered the functionality offered by SYS_kcmp and has
started to depend upon it. In particular, Mesa uses SYS_kcmp for
os_same_file_description() in order to identify when two fd (e.g. device
or dmabuf) point to the same struct file. Since they depend on it for
core functionality, lift SYS_kcmp out of the non-default
CONFIG_CHECKPOINT_RESTORE into the selectable syscall category.
Rasmus Villemoes also pointed out that systemd uses SYS_kcmp to
deduplicate the per-service file descriptor store.
Note that some distributions such as Ubuntu are already enabling
CHECKPOINT_RESTORE in their configs and so, by extension, SYS_kcmp.
References: https://gitlab.freedesktop.org/drm/intel/-/issues/3046
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Will Drewry <wad@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> # DRM depends on kcmp
Acked-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> # systemd uses kcmp
Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205220012.1983-1-chris@chris-wilson.co.uk
When TPM 2.0 trusted keys code was moved to the trusted keys subsystem,
the operations were unwrapped from tpm_try_get_ops() and tpm_put_ops(),
which are used to take temporarily the ownership of the TPM chip. The
ownership is only taken inside tpm_send(), but this is not sufficient,
as in the key load TPM2_CC_LOAD, TPM2_CC_UNSEAL and TPM2_FLUSH_CONTEXT
need to be done as a one single atom.
Take the TPM chip ownership before sending anything with
tpm_try_get_ops() and tpm_put_ops(), and use tpm_transmit_cmd() to send
TPM commands instead of tpm_send(), reverting back to the old behaviour.
Fixes: 2e19e10131 ("KEYS: trusted: Move TPM2 trusted keys code")
Reported-by: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: stable@vger.kernel.org
Cc: David Howells <dhowells@redhat.com>
Cc: Mimi Zohar <zohar@linux.ibm.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Acked-by Sumit Garg <sumit.garg@linaro.org>
Tested-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Create sysfs per hash groups with 24 PCR files in them one group,
named pcr-<hash>, for each agile hash of the TPM. The files are
plugged in to a PCR read function which is TPM version agnostic, so
this works also for TPM 1.2 but the hash is only sha1 in that case.
Note: the macros used to create the hashes emit spurious checkpatch
warnings. Do not try to "fix" them as checkpatch recommends, otherwise
they'll break.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Instead of storing the version in a single integer and having various
kernel (and userspace) code how it's constructed, export individual
(major, patchlevel, sublevel) components and simplify kernel code that
uses it.
This should also make it easier on userspace.
Signed-off-by: Sasha Levin <sashal@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Paul Gortmaker reported a regression in the GCC version check. [1]
If you use GCC 4.8, the build breaks before showing the error message
"error Sorry, your version of GCC is too old - please use 4.9 or newer."
I do not want to apply his fix-up since it implies we would not be able
to remove any cc-option test. Anyway, I admit checking the GCC version
in <linux/compiler-gcc.h> is too late.
Almost at the same time, Linus also suggested to move the compiler
version error to Kconfig time. [2]
I unified the two similar scripts, gcc-version.sh and clang-version.sh
into cc-version.sh. The old scripts invoked the compiler multiple times
(3 times for gcc-version.sh, 4 times for clang-version.sh). I refactored
the code so the new one invokes the compiler just once, and also tried
my best to use shell-builtin commands where possible.
The new script runs faster.
$ time ./scripts/clang-version.sh clang
120000
real 0m0.029s
user 0m0.012s
sys 0m0.021s
$ time ./scripts/cc-version.sh clang
Clang 120000
real 0m0.009s
user 0m0.006s
sys 0m0.004s
cc-version.sh also shows an error message if the compiler is too old:
$ make defconfig CC=clang-9
*** Default configuration is based on 'x86_64_defconfig'
***
*** Compiler is too old.
*** Your Clang version: 9.0.1
*** Minimum Clang version: 10.0.1
***
scripts/Kconfig.include:46: Sorry, this compiler is not supported.
make[1]: *** [scripts/kconfig/Makefile:81: defconfig] Error 1
make: *** [Makefile:602: defconfig] Error 2
The new script takes care of ICC because we have <linux/compiler-intel.h>
although I am not sure if building the kernel with ICC is well-supported.
[1]: https://lore.kernel.org/r/20210110190807.134996-1-paul.gortmaker@windriver.com
[2]: https://lore.kernel.org/r/CAHk-=wh-+TMHPTFo1qs-MYyK7tZh-OQovA=pP3=e06aCVp6_kA@mail.gmail.com
Fixes: 87de84c914 ("kbuild: remove cc-option test of -Werror=date-time")
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Tested-by: Miguel Ojeda <ojeda@kernel.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Some internal PHY's have their events like link change reported by the
MAC interrupt. We have PHY_IGNORE_INTERRUPT to deal with this scenario.
I'm not too happy with this name. We don't ignore interrupts, typically
there is no interrupt exposed at a PHY level. So let's rename it to
PHY_MAC_INTERRUPT. This is in line with phy_mac_interrupt(), which is
called from the MAC interrupt handler to handle PHY events.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM54210E/BCM50212E has been verified to work correctly with the
auto-power down configuration done by bcm54xx_adjust_rxrefclk(), add it
to the list of PHYs working.
While we are at it, provide an appropriate name for the bit we are
changing which disables the RXC and TXC during auto-power down when
there is no energy on the cable.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a number of unused flags defined today and since we are scarce
on space and may need to introduce new flags in the future remove and
shift every existing flag down into a contiguous assignment.
PHY_BCM_FLAGS_MODE_1000BX was only used internally for the BCM54616S
PHY, so we allocate a driver private structure instead to store that
flag instead of canibalizing one from phydev->dev_flags for that
purpose.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
idt77252 is broken and wont load on amd64 systems
modprobe idt77252 shows the following
idt77252_init: skb->cb is too small (48 < 56)
Add packed attribute to struct idt77252_skb_prv and struct atm_skb_data
so that the total size can be <= sizeof(skb->cb)
Also convert runtime size check to buildtime size check in
idt77252_init()
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Thermal Monitoring part of PMIC5. This part is closely
coupled with ADC, using it's channels directly. ADC-TM support
generating interrupts on ADC value crossing low or high voltage bounds,
which is used to support thermal trip points.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205000118.493610-3-dmitry.baryshkov@linaro.org
SFI-based platforms are gone. So does this framework.
This removes mention of SFI through the drivers and other code as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* powercap:
powercap: intel_rapl: Use topology interface in rapl_init_domains()
powercap: intel_rapl: Use topology interface in rapl_add_package()
powercap/intel_rapl: add support for AlderLake Mobile
powercap/drivers/dtpm: Fix size of object being allocated
powercap/drivers/dtpm: Fix an IS_ERR() vs NULL check
powercap/drivers/dtpm: Fix some missing unlock bugs
powercap/drivers/dtpm: Fix a double shift bug
powercap/drivers/dtpm: Fix __udivdi3 and __aeabi_uldivmod unresolved symbols
powercap/drivers/dtpm: Add CPU energy model based support
powercap/drivers/dtpm: Add API for dynamic thermal power management
Documentation/powercap/dtpm: Add documentation for dtpm
units: Add Watt units
* pm-misc:
PM: Kconfig: remove unneeded "default n" options
PM: EM: update Kconfig description and drop "default n" option
It can be useful to the interpreter to know which flags are in use.
For instance, knowing if the preserve-argv[0] is in use would
allow to skip the pathname argument.
This patch uses an unused auxiliary vector, AT_FLAGS, to add a
flag to inform interpreter if the preserve-argv[0] is enabled.
Note by Helge Deller:
The real-world user of this patch is qemu-user, which needs to know
if it has to preserve the argv[0]. See Debian bug #970460.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: YunQiang Su <ysu@wavecomp.com>
URL: http://bugs.debian.org/970460
Signed-off-by: Helge Deller <deller@gmx.de>
* pm-opp: (37 commits)
PM / devfreq: Add required OPPs support to passive governor
PM / devfreq: Cache OPP table reference in devfreq
OPP: Add function to look up required OPP's for a given OPP
opp: Replace ENOTSUPP with EOPNOTSUPP
opp: Fix "foo * bar" should be "foo *bar"
opp: Don't ignore clk_get() errors other than -ENOENT
opp: Update bandwidth requirements based on scaling up/down
opp: Allow lazy-linking of required-opps
opp: Remove dev_pm_opp_set_bw()
devfreq: tegra30: Migrate to dev_pm_opp_set_opp()
drm: msm: Migrate to dev_pm_opp_set_opp()
cpufreq: qcom: Migrate to dev_pm_opp_set_opp()
opp: Implement dev_pm_opp_set_opp()
opp: Update parameters of _set_opp_custom()
opp: Allow _generic_set_opp_clk_only() to work for non-freq devices
opp: Allow _generic_set_opp_regulator() to work for non-freq devices
opp: Allow _set_opp() to work for non-freq devices
opp: Split _set_opp() out of dev_pm_opp_set_rate()
opp: Keep track of currently programmed OPP
opp: No need to check clk for errors
...
* pm-sleep:
PM: sleep: Constify static struct attribute_group
PM: sleep: Use dev_printk() when possible
PM: sleep: No need to check PF_WQ_WORKER in thaw_kernel_threads()
* pm-core:
PM: runtime: Fix typos and grammar
PM: runtime: Fix resposible -> responsible in runtime.c
* pm-domains:
PM: domains: Simplify the calculation of variables
PM: domains: Add "performance" column to debug summary
PM: domains: Make of_genpd_add_subdomain() return -EPROBE_DEFER
PM: domains: Make set_performance_state() callback optional
PM: domains: use device's next wakeup to determine domain idle state
PM: domains: inform PM domain of a device's next wakeup
* pm-clk:
PM: clk: make PM clock layer compatible with clocks that must sleep
This reverts commit a8c3209998.
It is reported that the said commit caused regression in netvsc.
Reported-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Instead of doing it in place, convert GPIO_LOOKUP_IDX() and GPIO_HOG()
to be compund literals that's allow to use them as rvalue in assignments.
Due to above conversion, use compound literal from the header
in the gpio-aggregator.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The ocelot tagger is a hot mess currently, it relies on memory
initialized by the attached driver for basic frame transmission.
This is against all that DSA tagging protocols stand for, which is that
the transmission and reception of a DSA-tagged frame, the data path,
should be independent from the switch control path, because the tag
protocol is in principle hot-pluggable and reusable across switches
(even if in practice it wasn't until very recently). But if another
driver like dsa_loop wants to make use of tag_ocelot, it couldn't.
This was done to have common code between Felix and Ocelot, which have
one bit difference in the frame header format. Quoting from commit
67c2404922 ("net: dsa: felix: create a template for the DSA tags on
xmit"):
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
The really interesting part is that Seville should have had its own
tagging protocol defined - it is not compatible on the wire with Ocelot,
even for that single bit. In principle, a packet generated by
DSA_TAG_PROTO_OCELOT when booted on NXP LS1028A would look in a certain
way, but when booted on NXP T1040 it would look differently. The reverse
is also true: a packet generated by a Seville switch would be
interpreted incorrectly by Wireshark if it was told it was generated by
an Ocelot switch.
Actually things are a bit more nuanced. If we concentrate only on the
DSA tag, what I said above is true, but Ocelot/Seville also support an
optional DSA tag prefix, which can be short or long, and it is possible
to distinguish the two taggers based on an integer constant put in that
prefix. Nonetheless, creating a separate tagger is still justified,
since the tag prefix is optional, and without it, there is again no way
to distinguish.
Claiming backwards binary compatibility is a bit more tough, since I've
already changed the format of tag_ocelot once, in commit 5124197ce5
("net: dsa: tag_ocelot: use a short prefix on both ingress and egress").
Therefore I am not very concerned with treating this as a bugfix and
backporting it to stable kernels (which would be another mess due to the
fact that there would be lots of conflicts with the other DSA_TAG_PROTO*
definitions). It's just simpler to say that the string values of the
taggers have ABI value starting with kernel 5.12, which will be when the
changing of tag protocol via /sys/class/net/<dsa-master>/dsa/tagging
goes live.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Injection Frame Header and Extraction Frame Header that the switch
prepends to frames over the NPI port is also prepended to frames
delivered over the CPU port module's queues.
Let's unify the handling of the frame headers by making the ocelot
driver call some helpers exported by the DSA tagger. Among other things,
this allows us to get rid of the strange cpu_to_be32 when transmitting
the Injection Frame Header on ocelot, since the packing API uses
network byte order natively (when "quirks" is 0).
The comments above ocelot_gen_ifh talk about setting pop_cnt to 3, and
the cpu extraction queue mask to something, but the code doesn't do it,
so we don't do it either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a devm helper for clk_hw_register_fixed_factor() so that drivers that internally
register fixed factor clocks for things like dividers don't need to manually unregister
them on remove or if probe fails.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20210211052206.2955988-4-daniel@0x0f.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
pcpu_build_alloc_info() is an __init function that makes a call to
cpumask_clear_cpu(). With CONFIG_GCOV_PROFILE_ALL enabled, the inline
heuristics are modified and such cpumask_clear_cpu() which is marked
inline doesn't get inlined. Because it works on mask in __initdata,
modpost throws a section mismatch error.
Arnd sent a patch with the flatten attribute as an alternative [2]. I've
added it to compiler_attributes.h.
modpost complaint:
WARNING: modpost: vmlinux.o(.text+0x735425): Section mismatch in reference from the function cpumask_clear_cpu() to the variable .init.data:pcpu_build_alloc_info.mask
The function cpumask_clear_cpu() references
the variable __initdata pcpu_build_alloc_info.mask.
This is often because cpumask_clear_cpu lacks a __initdata
annotation or the annotation of pcpu_build_alloc_info.mask is wrong.
clang output:
mm/percpu.c:2724:5: remark: cpumask_clear_cpu not inlined into pcpu_build_alloc_info because too costly to inline (cost=725, threshold=325) [-Rpass-missed=inline]
[1] https://lore.kernel.org/linux-mm/202012220454.9F6Bkz9q-lkp@intel.com/
[2] https://lore.kernel.org/lkml/CAK8P3a2ZWfNeXKSm8K_SUhhwkor17jFo3xApLXjzfPqX0eUDUA@mail.gmail.com/
Reported-by: kernel test robot <lkp@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
napi_frags_finish() and napi_skb_finish() can only be called inside
NAPI Rx context, so we can feed NAPI cache with skbuff_heads that
got NAPI_MERGED_FREE verdict instead of immediate freeing.
Replace __kfree_skb() with __kfree_skb_defer() in napi_skb_finish()
and move napi_skb_free_stolen_head() to skbuff.c, so it can drop skbs
to NAPI cache.
As many drivers call napi_alloc_skb()/napi_get_frags() on their
receive path, this becomes especially useful.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of just bulk-flushing skbuff_heads queued up through
napi_consume_skb() or __kfree_skb_defer(), try to reuse them
on allocation path.
If the cache is empty on allocation, bulk-allocate the first
16 elements, which is more efficient than per-skb allocation.
If the cache is full on freeing, bulk-wipe the second half of
the cache (32 elements).
This also includes custom KASAN poisoning/unpoisoning to be
double sure there are no use-after-free cases.
To not change current behaviour, introduce a new function,
napi_build_skb(), to optionally use a new approach later
in drivers.
Note on selected bulk size, 16:
- this equals to XDP_BULK_QUEUE_SIZE, DEV_MAP_BULK_SIZE
and especially VETH_XDP_BATCH, which is also used to
bulk-allocate skbuff_heads and was tested on powerful
setups;
- this also showed the best performance in the actual
test series (from the array of {8, 16, 32}).
Suggested-by: Edward Cree <ecree.xilinx@gmail.com> # Divide on two halves
Suggested-by: Eric Dumazet <edumazet@google.com> # KASAN poisoning
Cc: Dmitry Vyukov <dvyukov@google.com> # Help with KASAN
Cc: Paolo Abeni <pabeni@redhat.com> # Reduced batch size
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function isn't much needed as NAPI skb queue gets bulk-freed
anyway when there's no more room, and even may reduce the efficiency
of bulk operations.
It will be even less needed after reusing skb cache on allocation path,
so remove it and this way lighten network softirqs a bit.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
s390 and alpha are the only 64 bit architectures with a 32-bit ino_t.
Since this is quite unusual this causes bugs from time to time.
See e.g. commit ebce3eb2f7 ("ceph: fix inode number handling on
arches with 32-bit ino_t") for an example.
This (obviously) also prevents s390 and alpha to use 64-bit ino_t for
tmpfs. See commit b85a7a8bb5 ("tmpfs: disallow CONFIG_TMPFS_INODE64
on s390").
Therefore switch both s390 and alpha to 64-bit ino_t. This should only
have an effect on the ustat system call. To prevent ABI breakage
define struct ustat compatible to the old layout and change
sys_ustat() accordingly.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
