When we set bit 10 high we use continuous mode and not single
mode. Let's correct this to avoid confusion. No functional
changes here, the code does the right thing with bit 10.
Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-5-tony@atomide.com
We can use iopoll for checking the EOCZ (end of conversion) bit. And with
this we now also want to handle the timeout errors properly.
For omap3, we need about 1.2ms for the single mode sampling to wait for
EOCZ down, so let's use 1.5ms timeout there. Waiting for sampling to start
is faster and we can use 1ms timeout.
Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-4-tony@atomide.com
At least for 4430, trying to use the single conversion mode eventually
hangs the thermal sensor. This can be quite easily seen with errors:
thermal thermal_zone0: failed to read out thermal zone (-5)
Also, trying to read the temperature shows a stuck value with:
$ while true; do cat /sys/class/thermal/thermal_zone0/temp; done
Where the temperature is not rising at all with the busy loop.
Additionally, the EOCZ (end of conversion) bit is not rising on 4430 in
single conversion mode while it works fine in continuous conversion mode.
It is also possible that the hung temperature sensor can affect the
thermal shutdown alert too.
Let's fix the issue by adding TI_BANDGAP_FEATURE_CONT_MODE_ONLY flag and
use it for 4430.
Note that we also need to add udelay to for the EOCZ (end of conversion)
bit polling as otherwise we have it time out too early on 4430. We'll be
changing the loop to use iopoll in the following clean-up patch.
Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-3-tony@atomide.com
On dra7, there is no Start of Conversion (SOC) register bit and we have an
empty bgap_soc_mask in the configuration for the thermal driver. Let's not
do pointless reads and writes with the empty mask.
There's also no point waiting for End of Conversion bit (EOCZ) to go high
on dra7. We only care about it going down, and are now mostly timing out
waiting for EOCZ high while it has already gone down.
When we add checking for the timeout errors in a later patch, waiting for
EOCZ high would cause bogus time out errors.
Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-2-tony@atomide.com
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210120162400.4115366-3-arnd@kernel.org
The tango platform is getting removed, so the driver is no
longer needed.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210120162400.4115366-2-arnd@kernel.org
The thermal zone can have cooling devices which are missing power actor
API. This could be due to missing Energy Model for devfreq or cpufreq
cooling device. In this case it is safe to fail the binding rather than
trying to workaround and control the temperature in such thermal zone.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210119114126.19480-1-lukasz.luba@arm.com
The change of the cooling device state should be used by the governor
or at least by the core code, not by the drivers themselves.
Remove the API usage and move the function declaration to the internal
headers.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20210118173824.9970-1-daniel.lezcano@linaro.org
Like previous patch, the intel_pch_thermal device is not in ACPI
ThermalZone namespace, so a critical trip doesn't mean shutdown.
Override the default .critical callback to prevent surprising thermal
shutdoown.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201221172345.36976-2-kai.heng.feng@canonical.com
We are seeing thermal shutdown on Intel based mobile workstations, the
shutdown happens during the first trip handle in
thermal_zone_device_register():
kernel: thermal thermal_zone15: critical temperature reached (101 C), shutting down
However, we shouldn't do a thermal shutdown here, since
1) We may want to use a dedicated daemon, Intel's thermald in this case,
to handle thermal shutdown.
2) For ACPI based system, _CRT doesn't mean shutdown unless it's inside
ThermalZone namespace. ACPI Spec, 11.4.4 _CRT (Critical Temperature):
"... If this object it present under a device, the device’s driver
evaluates this object to determine the device’s critical cooling
temperature trip point. This value may then be used by the device’s
driver to program an internal device temperature sensor trip point."
So a "critical trip" here merely means we should take a more aggressive
cooling method.
As int340x device isn't present under ACPI ThermalZone, override the
default .critical callback to prevent surprising thermal shutdown.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201221172345.36976-1-kai.heng.feng@canonical.com
The function thermal_zone_device_reset() is called in the
thermal_zone_device_register() which allocates and initialize the
structure. The passive field is already zero-ed by the allocation, the
function is useless.
Call directly thermal_zone_device_init() instead and
thermal_zone_device_reset().
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201222181110.1231977-1-daniel.lezcano@linaro.org
The code does no longer use the ms unit based fields to set the
delays as they are replaced by the jiffies.
Remove them and replace their user to use the jiffies version instead.
Cc: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Peter Kästle <peter@piie.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201216220337.839878-3-daniel.lezcano@linaro.org
The delays are also stored in jiffies based unit. Use them instead of
the ms.
Cc: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201216220337.839878-2-daniel.lezcano@linaro.org
The delays are stored in ms units and when the polling function is
called this delay is converted into jiffies at each call.
Instead of doing the conversion again and again, compute the jiffies
at init time and use the value directly when setting the polling.
Cc: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201216220337.839878-1-daniel.lezcano@linaro.org
The last site calling the thermal_zone_bind_cooling_device() function
with the THERMAL_TRIPS_NONE parameter was removed.
We can get rid of this test as no user of this function is calling
this function with this parameter.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-5-daniel.lezcano@linaro.org
The loop is here to create default cooling device binding on the
THERMAL_TRIPS_NONE number which is used to be the 'forced_passive'
feature. However, we removed all code dealing with that in the thermal
core, thus this binding does no longer make sense.
Remove it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-4-daniel.lezcano@linaro.org
The functions thermal_zone_device_rebind_exception and
thermal_zone_device_unbind_exception are not used from anywhere.
Remove that code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-2-daniel.lezcano@linaro.org
The code was reorganized in 2012 with the commit 0c01ebbfd3.
The main change is a loop on the trip points array and a unconditional
call to the throttle() ops of the governors for each of them even if
the trip temperature is not reached yet.
With this change, the 'forced_passive' is no longer checked in the
thermal_zone_device_update() function but in the step wise governor's
throttle() callback.
As the force_passive does no belong to the trip point array, the
thermal_zone_device_update() can not compare with the specified
passive temperature, thus does not detect the passive limit has been
crossed. Consequently, throttle() is never called and the
'forced_passive' branch is unreached.
In addition, the default processor cooling device is not automatically
bound to the thermal zone if there is not passive trip point, thus the
'forced_passive' can not operate.
If there is an active trip point, then the throttle function will be
called to mitigate at this temperature and the 'forced_passive' will
override the mitigation of the active trip point in this case but with
the default cooling device bound to the thermal zone, so usually a
fan, and that is not a passive cooling effect.
Given the regression exists since more than 8 years, nobody complained
and at the best of my knowledge there is no bug open in
https://bugzilla.kernel.org, it is reasonable to say it is unused.
Remove the 'forced_passive' related code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-1-daniel.lezcano@linaro.org
The acpi driver wants to do a netlink notification in case of a hot or
critical trip point. Implement the corresponding ops to be used for
the thermal zone and use them instead of the notify ops.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20201210121514.25760-3-daniel.lezcano@linaro.org
- Fix recently introduced crash in the intel_pstate driver that
occurs if scale-invariance is disabled during resume from
suspend-to-RAM due to inconsistent changes of APERF or MPERF
MSR values made by the platform firmware (Rafael Wysocki).
- Fix a memory leak and add a missing clk_put() in error paths in
the OPP framework (Quanyang Wang, Viresh Kumar).
- Add new C-states table for SnowRidge processors to the intel_idle
driver (Artem Bityutskiy).
- Update the MAINTAINERS entry for cpuidle to make it clear that
the governors are covered by it too (Lukas Bulwahn).
-----BEGIN PGP SIGNATURE-----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=51jM
-----END PGP SIGNATURE-----
Merge tag 'pm-5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a crash in intel_pstate during resume from suspend-to-RAM
that may occur after recent changes and two resource leaks in error
paths in the operating performance points (OPP) framework, add a new
C-states table to intel_idle and update the cpuidle MAINTAINERS entry
to cover the governors too.
Specifics:
- Fix recently introduced crash in the intel_pstate driver that
occurs if scale-invariance is disabled during resume from
suspend-to-RAM due to inconsistent changes of APERF or MPERF MSR
values made by the platform firmware (Rafael Wysocki).
- Fix a memory leak and add a missing clk_put() in error paths in the
OPP framework (Quanyang Wang, Viresh Kumar).
- Add new C-states table for SnowRidge processors to the intel_idle
driver (Artem Bityutskiy).
- Update the MAINTAINERS entry for cpuidle to make it clear that the
governors are covered by it too (Lukas Bulwahn)"
* tag 'pm-5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_idle: add SnowRidge C-state table
cpufreq: intel_pstate: Fix fast-switch fallback path
opp: Call the missing clk_put() on error
opp: fix memory leak in _allocate_opp_table
MAINTAINERS: include governors into CPU IDLE TIME MANAGEMENT FRAMEWORK
This is a load of driver fixes (12 ufs, 1 mpt3sas, 1 cxgbi). The big
core two fixes are for power management ("block: Do not accept any
requests while suspended" and "block: Fix a race in the runtime power
management code") which finally sorts out the resume problems we've
occasionally been having. To make the resume fix, there are seven
necessary precursors which effectively renames REQ_PREEMPT to REQ_PM,
so every "special" request in block is automatically a power
management exempt one. All of the non-PM preempt cases are removed
except for the one in the SCSI Parallel Interface (spi) domain
validation which is a genuine case where we have to run requests at
high priority to validate the bus so this becomes an autopm get/put
protected request.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX+98LyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYvLAP9K+HBT
Lrkt3VWc9gq6F36+QH/SeW8IyXGaj77ysFHXxwD/UambRjRK8IA24mvf9sWeLLj6
p8CqCHUkCXqP48IiymE=
=NHrx
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a load of driver fixes (12 ufs, 1 mpt3sas, 1 cxgbi).
The big core two fixes are for power management ("block: Do not accept
any requests while suspended" and "block: Fix a race in the runtime
power management code") which finally sorts out the resume problems
we've occasionally been having.
To make the resume fix, there are seven necessary precursors which
effectively renames REQ_PREEMPT to REQ_PM, so every "special" request
in block is automatically a power management exempt one.
All of the non-PM preempt cases are removed except for the one in the
SCSI Parallel Interface (spi) domain validation which is a genuine
case where we have to run requests at high priority to validate the
bus so this becomes an autopm get/put protected request"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (22 commits)
scsi: cxgb4i: Fix TLS dependency
scsi: ufs: Un-inline ufshcd_vops_device_reset function
scsi: ufs: Re-enable WriteBooster after device reset
scsi: ufs-mediatek: Use correct path to fix compile error
scsi: mpt3sas: Signedness bug in _base_get_diag_triggers()
scsi: block: Do not accept any requests while suspended
scsi: block: Remove RQF_PREEMPT and BLK_MQ_REQ_PREEMPT
scsi: core: Only process PM requests if rpm_status != RPM_ACTIVE
scsi: scsi_transport_spi: Set RQF_PM for domain validation commands
scsi: ide: Mark power management requests with RQF_PM instead of RQF_PREEMPT
scsi: ide: Do not set the RQF_PREEMPT flag for sense requests
scsi: block: Introduce BLK_MQ_REQ_PM
scsi: block: Fix a race in the runtime power management code
scsi: ufs-pci: Enable UFSHCD_CAP_RPM_AUTOSUSPEND for Intel controllers
scsi: ufs-pci: Fix recovery from hibernate exit errors for Intel controllers
scsi: ufs-pci: Ensure UFS device is in PowerDown mode for suspend-to-disk ->poweroff()
scsi: ufs-pci: Fix restore from S4 for Intel controllers
scsi: ufs-mediatek: Keep VCC always-on for specific devices
scsi: ufs: Allow regulators being always-on
scsi: ufs: Clear UAC for RPMB after ufshcd resets
...
-----BEGIN PGP SIGNATURE-----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=OvP3
-----END PGP SIGNATURE-----
Merge tag 'block-5.11-2021-01-01' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Two minor block fixes from this last week that should go into 5.11:
- Add missing NOWAIT debugfs definition (Andres)
- Fix kerneldoc warning introduced this merge window (Randy)"
* tag 'block-5.11-2021-01-01' of git://git.kernel.dk/linux-block:
block: add debugfs stanza for QUEUE_FLAG_NOWAIT
fs: block_dev.c: fix kernel-doc warnings from struct block_device changes
-----BEGIN PGP SIGNATURE-----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=XYT5
-----END PGP SIGNATURE-----
Merge tag 'io_uring-5.11-2021-01-01' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"A few fixes that should go into 5.11, all marked for stable as well:
- Fix issue around identity COW'ing and users that share a ring
across processes
- Fix a hang associated with unregistering fixed files (Pavel)
- Move the 'process is exiting' cancelation a bit earlier, so
task_works aren't affected by it (Pavel)"
* tag 'io_uring-5.11-2021-01-01' of git://git.kernel.dk/linux-block:
kernel/io_uring: cancel io_uring before task works
io_uring: fix io_sqe_files_unregister() hangs
io_uring: add a helper for setting a ref node
io_uring: don't assume mm is constant across submits
Commit 436e980e2e ("kbuild: don't hardcode depmod path") stopped
hard-coding the path of depmod, but in the process caused trouble for
distributions that had that /sbin location, but didn't have it in the
PATH (generally because /sbin is limited to the super-user path).
Work around it for now by just adding /sbin to the end of PATH in the
depmod.sh script.
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For cancelling io_uring requests it needs either to be able to run
currently enqueued task_works or having it shut down by that moment.
Otherwise io_uring_cancel_files() may be waiting for requests that won't
ever complete.
Go with the first way and do cancellations before setting PF_EXITING and
so before putting the task_work infrastructure into a transition state
where task_work_run() would better not be called.
Cc: stable@vger.kernel.org # 5.5+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_sqe_files_unregister() uninterruptibly waits for enqueued ref nodes,
however requests keeping them may never complete, e.g. because of some
userspace dependency. Make sure it's interruptible otherwise it would
hang forever.
Cc: stable@vger.kernel.org # 5.6+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Setting a new reference node to a file data is not trivial, don't repeat
it, add and use a helper.
Cc: stable@vger.kernel.org # 5.6+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
trivial fixups for the new msgr2 support.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAl/stgUTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi7SECACa5sWn5GKArGNCYesG/Xnbl4FbtorA
QNmDS7z5SBTsxQfOmkIq7Xon9fRxXEpWzr/eCEZKcXc+REHXGsy8zFz/HA0t97SS
tSho288zfEifGK0k2aptBTXAiEnzhIweu9f5ZbxfLN+JPyfynxfvXytdXYFeU/Op
zLUBSjJusmm671APBvyWl/5h/2N7XkpBM3AWNJjaW26+Mft3SpsS8Ui+USWb9SJF
YEmsVR03W2pbSS66a774bThoLP8exfg7xMfUcWRHqYs3Awpp0mwMnKkHMfooYLGA
Cc5FsQ7Exin23B4vCm6+0prg/cgwBg516HfsFH/jTcE2D/PjSCEX7tXE
=ZGwT
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.11-rc2' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A fix for an edge case in MClientRequest encoding and a couple of
trivial fixups for the new msgr2 support"
* tag 'ceph-for-5.11-rc2' of git://github.com/ceph/ceph-client:
libceph: add __maybe_unused to DEFINE_MSGR2_FEATURE
libceph: align session_key and con_secret to 16 bytes
libceph: fix auth_signature buffer allocation in secure mode
ceph: reencode gid_list when reconnecting
Add C-state table for the SnowRidge SoC which is found on Intel Jacobsville
platforms.
The following has been changed.
1. C1E latency changed from 10us to 15us. It was measured using the
open source "wult" tool (the "nic" method, 15us is the 99.99th
percentile).
2. C1E power break even changed from 20us to 25us, which may result
in less C1E residency in some workloads.
3. C6 latency changed from 50us to 130us. Measured the same way as C1E.
The C6 C-state is supported only by some SnowRidge revisions, so add a C-state
table commentary about this.
On SnowRidge, C6 support is enumerated via the usual mechanism: "mwait" leaf of
the "cpuid" instruction. The 'intel_idle' driver does check this leaf, so even
though C6 is present in the table, the driver will only use it if the CPU does
support it.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When sugov_update_single_perf() falls back to the "frequency"
path due to the missing scale-invariance, it will call
cpufreq_driver_fast_switch() via sugov_fast_switch()
and the driver's ->fast_switch() callback will be invoked,
so it must not be NULL.
However, after commit a365ab6b9d ("cpufreq: intel_pstate: Implement
the ->adjust_perf() callback") intel_pstate sets ->fast_switch() to
NULL when it is going to use intel_cpufreq_adjust_perf(), which is a
mistake, because on x86 the scale-invariance may be turned off
dynamically, so modify it to retain the original ->adjust_perf()
callback pointer.
Fixes: a365ab6b9d ("cpufreq: intel_pstate: Implement the ->adjust_perf() callback")
Reported-by: Kenneth R. Crudup <kenny@panix.com>
Tested-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull operating performance points (OPP) framework fixes for 5.11-rc2
from Viresh Kumar:
"This contains two patches to fix freeing of resources in error paths."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Call the missing clk_put() on error
opp: fix memory leak in _allocate_opp_table
This was missed in 021a24460d. Leads to the numeric value of
QUEUE_FLAG_NOWAIT (i.e. 29) showing up in
/sys/kernel/debug/block/*/state.
Fixes: 021a24460d
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix new kernel-doc warnings in fs/block_dev.c:
../fs/block_dev.c:1066: warning: Excess function parameter 'whole' description in 'bd_abort_claiming'
../fs/block_dev.c:1837: warning: Function parameter or member 'dev' not described in 'lookup_bdev'
Fixes: 4e7b5671c6 ("block: remove i_bdev")
Fixes: 37c3fc9abb ("block: simplify the block device claiming interface")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: linux-fsdevel@vger.kernel.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge misc fixes from Andrew Morton:
"16 patches
Subsystems affected by this patch series: mm (selftests, hugetlb,
pagecache, mremap, kasan, and slub), kbuild, checkpatch, misc, and
lib"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: slub: call account_slab_page() after slab page initialization
zlib: move EXPORT_SYMBOL() and MODULE_LICENSE() out of dfltcc_syms.c
lib/zlib: fix inflating zlib streams on s390
lib/genalloc: fix the overflow when size is too big
kdev_t: always inline major/minor helper functions
sizes.h: add SZ_8G/SZ_16G/SZ_32G macros
local64.h: make <asm/local64.h> mandatory
kasan: fix null pointer dereference in kasan_record_aux_stack
mm: generalise COW SMC TLB flushing race comment
mm/mremap.c: fix extent calculation
mm: memmap defer init doesn't work as expected
mm: add prototype for __add_to_page_cache_locked()
checkpatch: prefer strscpy to strlcpy
Revert "kbuild: avoid static_assert for genksyms"
mm/hugetlb: fix deadlock in hugetlb_cow error path
selftests/vm: fix building protection keys test
It's convenient to have page->objects initialized before calling into
account_slab_page(). In particular, this information can be used to
pre-alloc the obj_cgroup vector.
Let's call account_slab_page() a bit later, after the initialization of
page->objects.
This commit doesn't bring any functional change, but is required for
further optimizations.
[akpm@linux-foundation.org: undo changes needed by forthcoming mm-memcg-slab-pre-allocate-obj_cgroups-for-slab-caches-with-slab_account.patch]
Link: https://lkml.kernel.org/r/20201110195753.530157-1-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit 11fb479ff5 ("zlib: export S390 symbols for zlib modules"), I
added EXPORT_SYMBOL()s to dfltcc_inflate.c but then Mikhail said that
these should probably be in dfltcc_syms.c with the other
EXPORT_SYMBOL()s.
However, that is contrary to the current kernel style, which places
EXPORT_SYMBOL() immediately after the function that it applies to, so
move all EXPORT_SYMBOL()s to their respective function locations and
drop the dfltcc_syms.c file. Also move MODULE_LICENSE() from the
deleted file to dfltcc.c.
[rdunlap@infradead.org: remove dfltcc_syms.o from Makefile]
Link: https://lkml.kernel.org/r/20201227171837.15492-1-rdunlap@infradead.org
Link: https://lkml.kernel.org/r/20201219052530.28461-1-rdunlap@infradead.org
Fixes: 11fb479ff5 ("zlib: export S390 symbols for zlib modules")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Zaslonko Mikhail <zaslonko@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Decompressing zlib streams on s390 fails with "incorrect data check"
error.
Userspace zlib checks inflate_state.flags in order to byteswap checksums
only for zlib streams, and s390 hardware inflate code, which was ported
from there, tries to match this behavior. At the same time, kernel zlib
does not use inflate_state.flags, so it contains essentially random
values. For many use cases either zlib stream is zeroed out or checksum
is not used, so this problem is masked, but at least SquashFS is still
affected.
Fix by always passing a checksum to and from the hardware as is, which
matches zlib_inflate()'s expectations.
Link: https://lkml.kernel.org/r/20201215155551.894884-1-iii@linux.ibm.com
Fixes: 1261961000 ("lib/zlib: add s390 hardware support for kernel zlib_inflate")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Cc: <stable@vger.kernel.org> [5.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some graphic card has very big memory on chip, such as 32G bytes.
In the following case, it will cause overflow:
pool = gen_pool_create(PAGE_SHIFT, NUMA_NO_NODE);
ret = gen_pool_add(pool, 0x1000000, SZ_32G, NUMA_NO_NODE);
va = gen_pool_alloc(pool, SZ_4G);
The overflow occurs in gen_pool_alloc_algo_owner():
....
size = nbits << order;
....
The @nbits is "int" type, so it will overflow.
Then the gen_pool_avail() will return the wrong value.
This patch converts some "int" to "unsigned long", and
changes the compare code in while.
Link: https://lkml.kernel.org/r/20201229060657.3389-1-sjhuang@iluvatar.ai
Signed-off-by: Huang Shijie <sjhuang@iluvatar.ai>
Reported-by: Shi Jiasheng <jiasheng.shi@iluvatar.ai>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add these macros, since we can use them in drivers.
Link: https://lkml.kernel.org/r/20201229072819.11183-1-sjhuang@iluvatar.ai
Signed-off-by: Huang Shijie <sjhuang@iluvatar.ai>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make <asm-generic/local64.h> mandatory in include/asm-generic/Kbuild and
remove all arch/*/include/asm/local64.h arch-specific files since they
only #include <asm-generic/local64.h>.
This fixes build errors on arch/c6x/ and arch/nios2/ for
block/blk-iocost.c.
Build-tested on 21 of 25 arch-es. (tools problems on the others)
Yes, we could even rename <asm-generic/local64.h> to
<linux/local64.h> and change all #includes to use
<linux/local64.h> instead.
Link: https://lkml.kernel.org/r/20201227024446.17018-1-rdunlap@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <jacquiot.aurelien@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
