KVM currently does not trap ID register accesses from an AArch32 EL1.
This is painful for a couple of reasons. Certain unimplemented features
are visible to AArch32 EL1, as we limit PMU to version 3 and the debug
architecture to v8.0. Additionally, we attempt to paper over
heterogeneous systems by using register values that are safe
system-wide. All this hard work is completely sidestepped because KVM
does not set TID3 for AArch32 guests.
Fix up handling of CP15 feature registers by simply rerouting to their
AArch64 aliases. Punt setting HCR_EL2.TID3 to a later change, as we need
to fix up the oddball CP10 feature registers still.
Signed-off-by: Oliver Upton <oupton@google.com>
Reviewed-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220503060205.2823727-4-oupton@google.com
emulate_sys_reg() returns 1 unconditionally, even though a a system
register access can fail. Furthermore, kvm_handle_sys_reg() writes to Rt
for every register read, regardless of if it actually succeeded.
Though this pattern is safe (as params.regval is initialized with the
current value of Rt) it is a bit ugly. Indicate failure if the register
access could not be emulated and only write to Rt on success.
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220503060205.2823727-3-oupton@google.com
KVM indicates success/failure in several ways, but generally an integer
is used when conditionally bouncing to userspace is involved. That is
not the case from emulate_cp(); just use a bool instead.
No functional change intended.
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220503060205.2823727-2-oupton@google.com
Ido Schimmel says:
====================
mlxsw: Remove size limitations on egress descriptor buffer
Petr says:
Spectrum machines have two resources related to keeping packets in an
internal buffer: bytes (allocated in cell-sized units) for packet payload,
and descriptors, for keeping headers. Currently, mlxsw only configures the
bytes part of the resource management.
Spectrum switches permit a full parallel configuration for the descriptor
resources, including port-pool and port-TC-pool quotas. By default, these
are all configured to use pool 14, with an infinite quota. The ingress pool
14 is then infinite in size.
However, egress pool 14 has finite size by default. The size is chip
dependent, but always much lower than what the chip actually permits. As a
result, we can easily construct workloads that exhaust the configured
descriptor limit.
Going forward, mlxsw will have to fix this issue properly by maintaining
descriptor buffer sizes, TC bindings, and quotas that match the
architecture recommendation. Short term, fix the issue by configuring the
egress descriptor pool to be infinite in size as well. This will maintain
the same configuration philosophy, but will unlock all chip resources to be
usable.
In this patchset, patch #1 first adds the "desc" field into the pool
configuration register. Then in patch #2, the new field is used to
configure both ingress and egress pool 14 as infinite.
In patches #3 and #4, add a selftest that verifies that a large burst
can be absorbed by the shared buffer. This test specifically exercises a
scenario where descriptor buffer is the limiting factor and the test
fails without the above patches.
====================
Link: https://lore.kernel.org/r/20220502084926.365268-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a test that sends 1Gbps of traffic through the switch, into which it
then injects a burst of traffic and tests that there are no drops.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add two helpers, start_traffic_pktsize() and start_tcp_traffic_pktsize(),
that allow explicit overriding of packet size. Change start_traffic() and
start_tcp_traffic() to dispatch through these helpers with the default
packet size.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Spectrum machines have two resources related to keeping packets in an
internal buffer: bytes (allocated in cell-sized units) for packet payload,
and descriptors, for keeping metadata. Currently, mlxsw only configures the
bytes part of the resource management.
Spectrum switches permit a full parallel configuration for the descriptor
resources, including port-pool and port-TC-pool quotas. By default, these
are all configured to use pool 14, with an infinite quota. The ingress pool
14 is then infinite in size.
However, egress pool 14 has finite size by default. The size is chip
dependent, but always much lower than what the chip actually permits. As a
result, we can easily construct workloads that exhaust the configured
descriptor limit.
Fix the issue by configuring the egress descriptor pool to be infinite in
size as well. This will maintain the configuration philosophy of the
default configuration, but will unlock all chip resources to be usable.
In the code, include both the configuration of ingress and ingress, mostly
for clarity.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
SBPR, or Shared Buffer Pools Register, configures and retrieves the shared
buffer pools and configuration. The desc field determines whether the
configuration relates to the byte pool or the descriptor pool.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The macro idtentry() (through idtentry_body()) calls error_entry()
unconditionally even on XENPV. But XENPV needs to only push and clear
regs.
PUSH_AND_CLEAR_REGS in error_entry() makes the stack not return to its
original place when the function returns, which means it is not possible
to convert it to a C function.
Carve out PUSH_AND_CLEAR_REGS out of error_entry() and into a separate
function and call it before error_entry() in order to avoid calling
error_entry() on XENPV.
It will also allow for error_entry() to be converted to C code that can
use inlined sync_regs() and save a function call.
[ bp: Massage commit message. ]
Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220503032107.680190-4-jiangshanlai@gmail.com
error_entry() calls fixup_bad_iret() before sync_regs() if it is a fault
from a bad IRET, to copy pt_regs to the kernel stack. It switches to the
kernel stack directly after sync_regs().
But error_entry() itself is also a function call, so it has to stash
the address it is going to return to, in %r12 which is unnecessarily
complicated.
Move the stack switching after error_entry() and get rid of the need to
handle the return address.
[ bp: Massage commit message. ]
Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220503032107.680190-3-jiangshanlai@gmail.com
The reference clock for the HDMI controller has been renamed to 'ref',
the previous 'vpll' name is only left for compatibility in the driver.
Rename the clock to the new name.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220422072841.2206452-7-s.hauer@pengutronix.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
"vpll" is a misnomer. A clock input to a device should be named after
the usage in the device, not after the clock that drives it. On the
rk3568 the same clock is driven by the HPLL.
This patch adds "ref" as a new alternative clock name for "vpll"
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220422072841.2206452-6-s.hauer@pengutronix.de
"vpll" is a misnomer. A clock input to a device should be named after
the usage in the device, not after the clock that drives it. On the
rk3568 the same clock is driven by the HPLL.
To fix that, this patch renames the vpll clock to ref clock. The clock
name "vpll" is left for compatibility to old device trees.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220422072841.2206452-5-s.hauer@pengutronix.de
The VOP2 has an interface mux which decides to which encoder(s) a CRTC
is routed to. The encoders and CRTCs are connected via of_graphs in the
device tree. When given an encoder the VOP2 driver needs to know to
which internal register setting this encoder matches. For this the VOP2
binding offers different endpoints, one for each possible encoder. The
endpoint ids of these endpoints are used as a key from an encoders
device tree description to the internal register setting.
This patch adds the key aka endpoint id to struct rockchip_encoder plus
a function to read the endpoint id starting from the encoders device
node.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220422072841.2206452-4-s.hauer@pengutronix.de
The VOP2 driver needs rockchip specific information for a drm_encoder.
This patch creates a struct rockchip_encoder with a struct drm_encoder
embedded in it. This is used throughout the rockchip driver instead of
struct drm_encoder directly.
The information the VOP2 drivers needs is the of_graph endpoint node
of the encoder. To ease bisectability this is added here.
While at it convert the different encoder-to-driverdata macros to
static inline functions in order to gain type safety and readability.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220422072841.2206452-3-s.hauer@pengutronix.de
In emulated environments, the bridge ports enslaved to br1 get a carrier
before changing br1's PVID. This means that by the time the PVID is
changed, br1 is already operational and configured with an IPv6
link-local address.
When the test is run with netdevs registered by mlxsw, changing the PVID
is vetoed, as changing the VID associated with an existing L3 interface
is forbidden. This restriction is similar to the 8021q driver's
restriction of changing the VID of an existing interface.
Fix this by taking br1 down and bringing it back up when it is fully
configured.
With this fix, the test reliably passes on top of both the SW and HW
data paths (emulated or not).
Fixes: 239e754af8 ("selftests: forwarding: Test mirror-to-gretap w/ UL 802.1q")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20220502084507.364774-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Always stash the address error_entry() is going to return to, in %r12
and get rid of the void *error_entry_ret; slot in struct bad_iret_stack
which was supposed to account for it and pt_regs pushed on the stack.
After this, both fixup_bad_iret() and sync_regs() can work on a struct
pt_regs pointer directly.
[ bp: Rewrite commit message, touch ups. ]
Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220503032107.680190-2-jiangshanlai@gmail.com
Whenever pclk_vo is enabled hclk_vo must be enabled as well. This is
described in the Reference Manual as:
| 2.8.6 NIU Clock gating reliance
|
| A part of niu clocks have a dependence on another niu clock in order to
| sharing the internal bus. When these clocks are in use, another niu
| clock must be opened, and cannot be gated. These clocks and the special
| clock on which they are relied are as following:
|
| Clocks which have dependency The clock which can not be gated
| -----------------------------------------------------------------
| ...
| pclk_vo_niu, hclk_vo_s_niu hclk_vo_niu
| ...
The clock framework doesn't offer a way to enable clock B whenever clock A is
enabled, at least not when B is not an ancestor of A. Workaround this by
marking hclk_vo as critical so it is never disabled. This is suboptimal in
terms of power consumption, but a stop gap solution until the clock framework
has a way to deal with this.
We have this clock tree:
| aclk_vo 2 2 0 300000000 0 0 50000 Y
| aclk_hdcp 0 0 0 300000000 0 0 50000 N
| pclk_vo 2 3 0 75000000 0 0 50000 Y
| pclk_edp_ctrl 0 0 0 75000000 0 0 50000 N
| pclk_dsitx_1 0 0 0 75000000 0 0 50000 N
| pclk_dsitx_0 1 2 0 75000000 0 0 50000 Y
| pclk_hdmi_host 1 2 0 75000000 0 0 50000 Y
| pclk_hdcp 0 0 0 75000000 0 0 50000 N
| hclk_vo 2 5 0 150000000 0 0 50000 Y
| hclk_hdcp 0 0 0 150000000 0 0 50000 N
| hclk_vop 0 2 0 150000000 0 0 50000 N
Without this patch the edp, dsitx, hdmi and hdcp driver would enable their
clocks which then enables pclk_vo, but hclk_vo stays disabled and register
accesses just hang. hclk_vo is enabled by the VOP2 driver, so reproducibility
of this issue depends on the probe order.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220422072841.2206452-2-s.hauer@pengutronix.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Radhey Shyam Pandey says:
====================
emaclite: improve error handling and minor cleanup
This patchset does error handling for of_address_to_resource() and also
removes "Don't advertise 1000BASE-T" and auto negotiation.
Changes for v3:
- Resolve git apply conflicts for 2/2 patch.
Changes for v2:
- Added Andrew's reviewed by tag in 1/2 patch.
- Move ret to down to align with reverse xmas tree style in 2/2 patch.
- Also add fixes tag in 2/2 patch.
- Specify tree name in subject prefix.
====================
Link: https://lore.kernel.org/r/1651476470-23904-1-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
check the return value of of_address_to_resource() and also add
missing of_node_put() for np and npp nodes.
Fixes: e0a3bc6544 ("net: emaclite: Support multiple phys connected to one MDIO bus")
Addresses-Coverity: Event check_return value.
Signed-off-by: Shravya Kumbham <shravya.kumbham@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In xemaclite_open() function we are setting the max speed of
emaclite to 100Mb using phy_set_max_speed() function so,
there is no need to write the advertising registers to stop
giga-bit speed and the phy_start() function starts the
auto-negotiation so, there is no need to handle it separately
using advertising registers. Remove the phy_read and phy_write
of advertising registers in xemaclite_open() function.
Signed-off-by: Shravya Kumbham <shravya.kumbham@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tonghao Zhang says:
====================
use standard sysctl macro
From: Tonghao Zhang <xiangxia.m.yue@gmail.com>
This patchset introduce sysctl macro or replace var
with macro.
====================
Link: https://lore.kernel.org/r/20220501035524.91205-1-xiangxia.m.yue@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220429082637.1308182-2-yangyingliang@huawei.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: c7977ec4a3 ("pinctrl: sh-pfc: Convert to platform_get_*()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220429082637.1308182-1-yangyingliang@huawei.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Unlike on R-Car Gen3 SoCs, setting a bit to zero in a GPIO / Peripheral
Function Select Register (GPSRn) on R-Car S4-8 is not always sufficient
to configure a pin for GPIO. For I2C-capable pins, the I2C function
must also be explicitly disabled in the corresponding Module Select
Register (MODSELn).
Add the missing FN_SEL_I2Ci_0 function enums to the pinmux_data[] array
by temporarily overriding the GP_1_j_FN function enum to expand to two
enums: the original GP_1_j_FN enum to configure the GPSR register bits,
and the missing FN_SEL_I2Ci_0 enum to configure the MODSEL register
bits.
Fixes: 030ac6d7ee ("pinctrl: renesas: Initial R8A779F0 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/c12c60ec1058140a37f03650043ab73f730f104f.1650610471.git.geert+renesas@glider.be
Unlike on R-Car Gen3 SoCs, setting a bit to zero in a GPIO / Peripheral
Function Select Register (GPSRn) on R-Car V3U is not always sufficient
to configure a pin for GPIO. For I2C-capable pins, the I2C function
must also be explicitly disabled in the corresponding Module Select
Register (MODSELn).
Add the missing FN_SEL_I2Ci_0 function enums to the pinmux_data[] array
by temporarily overriding the GP_2_j_FN function enum to expand to two
enums: the original GP_2_j_FN enum to configure the GSPR register bits,
and the missing FN_SEL_I2Ci_0 enum to configure the MODSEL register
bits.
Fixes: 741a7370fc ("pinctrl: renesas: Initial R8A779A0 (V3U) PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/4611e29e7b105513883084c1d6dc39c3ac8b525c.1650610471.git.geert+renesas@glider.be
Remove the duplicate and incorrect (uses "" instead of <>)
linux/string_helpers.h include.
Fixes: cc1338f259 ("drm/i915/xehp: Update topology dumps for Xe_HP")
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425154754.990815-1-jani.nikula@intel.com
The '#dma-channels' and '#dma-requests' properties were deprecated in
favor of these defined by generic dma-common DT bindings. Add new
properties while keeping old ones for backwards compatibility.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Message-Id: <20220503065201.51818-7-krzysztof.kozlowski@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The '#dma-channels' and '#dma-requests' properties were deprecated in
favor of these defined by generic dma-common DT bindings. Add new
properties while keeping old ones for backwards compatibility.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Message-Id: <20220503065201.51818-5-krzysztof.kozlowski@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
