This is the core driver for imx25 touchscreen/adc driver. The module
has one shared ADC and two different conversion queues which use the
ADC. The two queues are identical. Both can be used for general purpose
ADC but one is meant to be used for touchscreens.
This driver is the core which manages the central components and
registers of the TSC/ADC unit. It manages the IRQs and forwards them to
the correct components.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
[ensure correct ADC clock depending on the IPG clock]
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ARM64 PSCI kernel interfaces that initialize idle states and implement
the suspend API to enter them are generic and can be shared with the
ARM architecture.
To achieve that goal, this patch moves ARM64 PSCI idle management
code to drivers/firmware, so that the interface to initialize and
enter idle states can actually be shared by ARM and ARM64 arches
back-ends.
The ARM generic CPUidle implementation also requires the definition of
a cpuidle_ops section entry for the kernel to initialize the CPUidle
operations at boot based on the enable-method (ie ARM64 has the
statically initialized cpu_ops counterparts for that purpose); therefore
this patch also adds the required section entry on CONFIG_ARM for PSCI so
that the kernel can initialize the PSCI CPUidle back-end when PSCI is
the probed enable-method.
On ARM64 this patch provides no functional change.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> [arch/arm64]
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the DMA_ATTR_ALLOC_SINGLE_PAGES attribute to the
DMA-mapping subsystem.
This attribute can be used as a hint to the DMA-mapping subsystem that
it's likely not worth it to try to allocate large pages behind the
scenes. Large pages are likely to make an IOMMU TLB work more
efficiently but may not be worth it. See the Documentation contained in
this patch for more details about this attribute and when to use it.
Note that the name of the hint (DMA_ATTR_ALLOC_SINGLE_PAGES) is loosely
based on the name MADV_NOHUGEPAGE. Just as there is MADV_NOHUGEPAGE
vs. MADV_HUGEPAGE we could also add an "opposite" attribute to
DMA_ATTR_ALLOC_SINGLE_PAGES. Without having the "opposite" attribute
the lack of DMA_ATTR_ALLOC_SINGLE_PAGES means "use your best judgement
about whether to use small pages or large pages".
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As reported by Soohoon Lee, the HDIO_GET_32BIT ioctl does not
work correctly in compat mode with libata.
I have investigated the issue further and found multiple problems
that all appeared with the same commit that originally introduced
HDIO_GET_32BIT handling in libata back in linux-2.6.8 and presumably
also linux-2.4, as the code uses "copy_to_user(arg, &val, 1)" to copy
a 'long' variable containing either 0 or 1 to user space.
The problems with this are:
* On big-endian machines, this will always write a zero because it
stores the wrong byte into user space.
* In compat mode, the upper three bytes of the variable are updated
by the compat_hdio_ioctl() function, but they now contain
uninitialized stack data.
* The hdparm tool calling this ioctl uses a 'static long' variable
to store the result. This means at least the upper bytes are
initialized to zero, but calling another ioctl like HDIO_GET_MULTCOUNT
would fill them with data that remains stale when the low byte
is overwritten. Fortunately libata doesn't implement any of the
affected ioctl commands, so this would only happen when we query
both an IDE and an ATA device in the same command such as
"hdparm -N -c /dev/hda /dev/sda"
* The libata code for unknown reasons started using ATA_IOC_GET_IO32
and ATA_IOC_SET_IO32 as aliases for HDIO_GET_32BIT and HDIO_SET_32BIT,
while the ioctl commands that were added later use the normal
HDIO_* names. This is harmless but rather confusing.
This addresses all four issues by changing the code to use put_user()
on an 'unsigned long' variable in HDIO_GET_32BIT, like the IDE subsystem
does, and by clarifying the names of the ioctl commands.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Soohoon Lee <Soohoon.Lee@f5.com>
Tested-by: Soohoon Lee <Soohoon.Lee@f5.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
This was initially introduced in df2cf4a78e ("IGMP: Inhibit
reports for local multicast groups") by defining the sysctl in the
ipv4_net_table array, however it was never implemented to be
namespace aware. Fix this by changing the code accordingly.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it so that we can offload the checksums for a packet up
to a certain point and then begin computing the checksums via software.
Setting this up is fairly straight forward as all we need to do is reset
the values stored in csum and csum_start for the GSO context block.
One complication for this is remote checksum offload. In order to allow
the inner checksums to be offloaded while computing the outer checksum
manually we needed to have some way of indicating that the offload wasn't
real. In order to do that I replaced CHECKSUM_PARTIAL with
CHECKSUM_UNNECESSARY in the case of us computing checksums for the outer
header while skipping computing checksums for the inner headers. We clean
up the ip_summed flag and set it to either CHECKSUM_PARTIAL or
CHECKSUM_NONE once we hand the packet off to the next lower level.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the checksum maintained by GSO out of skb->csum and into
the GSO context block in order to allow for us to work on outer checksums
while maintaining the inner checksum offsets in the case of the inner
checksum being offloaded, while the outer checksums will be computed.
While updating the code I also did a minor cleanu-up on gso_make_checksum.
The change is mostly to make it so that we store the values and compute the
checksum instead of computing the checksum and then storing the values we
needed to update.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain 802.11 wireless deployments, there will be NA proxies
that use knowledge of the network to correctly answer requests.
To prevent unsolicitd advertisements on the shared medium from
being a problem, on such deployments wireless needs to drop them.
Enable this by providing an option called "drop_unsolicited_na".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to solve a problem with 802.11, the so-called hole-196 attack,
add an option (sysctl) called "drop_unicast_in_l2_multicast" which, if
enabled, causes the stack to drop IPv6 unicast packets encapsulated in
link-layer multi- or broadcast frames. Such frames can (as an attack)
be created by any member of the same wireless network and transmitted
as valid encrypted frames since the symmetric key for broadcast frames
is shared between all stations.
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_hdrlen is wasteful if you already have a pointer to struct tcphdr.
This splits the size calculation into a helper function that can be
used if a struct tcphdr is already available.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DRM drivers i915, nouveau and radeon may be compiled with
CONFIG_ACPI not set, in which case acpi_dev_present() is undefined.
Add a no-op stub for apple_gmux_present() which is used if
CONFIG_APPLE_GMUX is not enabled to avoid build breakage.
(CONFIG_APPLE_GMUX depends on CONFIG_ACPI.)
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160210131741.GA15492@wunner.de
Pull libata fixes from Tejun Heo:
- PORTS_IMPL workaround for very early ahci controllers is misbehaving
on new systems. Disabled on recent ahci versions.
- Old-style PIO state machine had a horrible locking problem. Don't
know how we've been getting away this far. Fixed.
- Other device specific updates.
* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: Intel DNV device IDs SATA
libata: fix sff host state machine locking while polling
libata-sff: use WARN instead of BUG on illegal host state machine state
libata: disable forced PORTS_IMPL for >= AHCI 1.3
libata: blacklist a Viking flash model for MWDMA corruption
drivers: ata: wake port before DMA stop for ALPM
Pull cgroup fixes from Tejun Heo:
- The destruction path of cgroup objects are asynchronous and
multi-staged and some of them ended up destroying parents before
children leading to failures in cpu and memory controllers. Ensure
that parents are always destroyed after children.
- cpuset mm node migration was performed synchronously while holding
threadgroup and cgroup mutexes and the recent threadgroup locking
update resulted in a possible deadlock. The migration is best effort
and shouldn't have been performed under those locks to begin with.
Made asynchronous.
- Minor documentation fix.
* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
Documentation: cgroup: Fix 'cgroup-legacy' -> 'cgroup-v1'
cgroup: make sure a parent css isn't freed before its children
cgroup: make sure a parent css isn't offlined before its children
cpuset: make mm migration asynchronous
Pull workqueue fixes from Tejun Heo:
"Workqueue fixes for v4.5-rc3.
- Remove a spurious triggering of flush dependency warning.
- Officially break local execution guarantee of unbound work items
and add a debug feature to flush out usages which depend on it.
- Work around CPU -> NODE mapping becoming invalid on CPU offline.
The branch is young but pushing out early as stable kernels are being
affected"
* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: handle NUMA_NO_NODE for unbound pool_workqueue lookup
workqueue: implement "workqueue.debug_force_rr_cpu" debug feature
workqueue: schedule WORK_CPU_UNBOUND work on wq_unbound_cpumask CPUs
Revert "workqueue: make sure delayed work run in local cpu"
workqueue: skip flush dependency checks for legacy workqueues
"rm -rf" is bricking some peoples' laptops because of variables being
used to store non-reinitializable firmware driver data that's required
to POST the hardware.
These are 100% bugs, and they need to be fixed, but in the mean time it
shouldn't be easy to *accidentally* brick machines.
We have to have delete working, and picking which variables do and don't
work for deletion is quite intractable, so instead make everything
immutable by default (except for a whitelist), and make tools that
aren't quite so broad-spectrum unset the immutable flag.
Signed-off-by: Peter Jones <pjones@redhat.com>
Tested-by: Lee, Chun-Yi <jlee@suse.com>
Acked-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
All the variables in this list so far are defined to be in the global
namespace in the UEFI spec, so this just further ensures we're
validating the variables we think we are.
Including the guid for entries will become more important in future
patches when we decide whether or not to allow deletion of variables
based on presence in this list.
Signed-off-by: Peter Jones <pjones@redhat.com>
Tested-by: Lee, Chun-Yi <jlee@suse.com>
Acked-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
This adds ucs2_utf8size(), which tells us how big our ucs2 string is in
bytes, and ucs2_as_utf8, which translates from ucs2 to utf8..
Signed-off-by: Peter Jones <pjones@redhat.com>
Tested-by: Lee, Chun-Yi <jlee@suse.com>
Acked-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
and a much more interesting kallsyms race which has been around approximately
forever. This fix is more invasive, and will require some care in backporting,
but I hated all the bandaids I could think of, so...
There are some more coming, which are only for breakages introduced this
cycle (livepatch), but wanted these in now.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Lt9v
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module fixes from Rusty Russell:
"Fix for async_probe module param added in 4.3 (clearly not widely used
yet), and a much more interesting kallsyms race which has been around
approximately forever. This fix is more invasive, and will require
some care in backporting, but I hated all the bandaids I could think
of, so...
There are some more coming, which are only for breakages introduced
this cycle (livepatch), but wanted these in now"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
modules: fix longstanding /proc/kallsyms vs module insertion race.
module: wrapper for symbol name.
modules: fix modparam async_probe request
This adds a routine, dev_pm_opp_set_rate(), responsible for configuring
power-supply and clock source for an OPP.
The OPP is found by matching against the target_freq passed to the
routine. This shall replace similar code present in most of the OPP
users and help simplify them a lot.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In few use cases (like: cpufreq), it is desired to get the maximum
latency for changing OPPs. Add support for that.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In few use cases (like: cpufreq), it is desired to get the maximum
voltage latency for changing OPPs. Add support for that.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This allows the OPP core to request/free the regulator resource,
attached to a device OPP. The regulator device is fetched using the name
provided by the driver, while calling: dev_pm_opp_set_regulator().
This will work for both OPP-v1 and v2 bindings.
This is a preliminary step for moving the OPP switching logic into the
OPP core.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The hardware's provided queue count may change at runtime with resource
provisioning. This patch allows a block driver to alter the number of
h/w queues available when its resource count changes.
The main part is a new blk-mq API to request a new number of h/w queues
for a given live tag set. The new API freezes all queues using that set,
then adjusts the allocated count prior to remapping these to CPUs.
The bulk of the rest just shifts where h/w contexts and all their
artifacts are allocated and freed.
The number of max h/w contexts is capped to the number of possible cpus
since there is no use for more than that. As such, all pre-allocated
memory for pointers need to account for the max possible rather than
the initial number of queues.
A side effect of this is that the blk-mq will proceed successfully as
long as it can allocate at least one h/w context. Previously it would
fail request queue initialization if less than the requested number
was allocated.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In addition to providing direct access to SPI bus, some spi controller
hardwares (like ti-qspi) provide special port (like memory mapped port)
that are optimized to improve SPI flash read performance.
This means the controller can automatically send the SPI signals
required to read data from the SPI flash device.
For this, SPI controller needs to know flash specific information like
read command to use, dummy bytes and address width.
Introduce spi_flash_read() interface to support accelerated read
over SPI flash devices. SPI master drivers can implement this callback to
support interfaces such as memory mapped read etc. m25p80 flash driver
and other flash drivers can call this make use of such interfaces. The
interface should only be used with SPI flashes and cannot be used with
other SPI devices.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add spi_split_transfers_maxsize method that splits
spi_transfers transparently into multiple transfers
that are below the given max-size.
This makes use of the spi_res framework via
spi_replace_transfers to allocate/free the extra
transfers as well as reverting back the changes applied
while processing the spi_message.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the spi_replace_transfers method that can get used
to replace some spi_transfers from a spi_message with other
transfers.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI resource management framework used while processing a spi_message
via the spi-core.
The basic idea is taken from devres, but as the allocation may happen
fairly frequently, some provisioning (in the form of an unused spi_device
pointer argument to spi_res_alloc) has been made so that at a later stage
we may implement reuse objects allocated earlier avoiding the repeated
allocation by keeping a cache of objects that we can reuse.
This framework can get used for:
* rewriting spi_messages
* to fullfill alignment requirements of the spi_master HW
* to fullfill transfer length requirements
(e.g: transfers need to be less than 64k)
* consolidate spi_messages with multiple transfers into a single transfer
when the total transfer length is below a threshold.
* reimplement spi_unmap_buf without explicitly needing to check if it has
been mapped
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel Braswell LPSS SPI controller actually has two chip selects and there
is no capabilities register where this could be found out. These two chip
selects are controlled by bits which are in slightly differrent location
than Broxton has.
Braswell Windows driver also starts chip select (ACPI DeviceSelection)
numbering from 1 so translate it to be suitable for Linux as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In Windows it is up to the SPI host controller driver to handle the ACPI
DeviceSelection as it likes. The SPI core does not take any part in it.
This is different in Linux because we always expect to have chip select in
range of 0 .. master->num_chipselect - 1.
In order to support this in Linux we need a way to allow the driver to
translate between ACPI DeviceSelection field and Linux chip select number
so provide a new optional hook ->fw_translate_cs() that can be used by a
driver to handle translation and call this hook if set during SPI slave
ACPI enumeration.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add KEY_ALLOC_BUILT_IN to convey that a key should have KEY_FLAG_BUILTIN
set rather than setting it after the fact.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
The comment is out of data. Also point out the performance drawback
of the barrier();__builtin_memcpy(); barrier() followed by another
copy from stack (__u) to lvalue;
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1453757600-11441-1-git-send-email-konrad.wilk@oracle.com
[ Made it a bit more readable. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Implement functions to get id of next existing quota structure in quota
file for quota tree based formats and thus for V2 quota format.
Signed-off-by: Jan Kara <jack@suse.cz>
Add infrastructure for supporting get_nextdqblk() callback for VFS
quotas. Translate the operation into a callback to appropriate
filesystem and consequently to quota format callback.
Signed-off-by: Jan Kara <jack@suse.cz>
Lockdep is initialized at compile time now. Get rid of lockdep_init().
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Krinkin <krinkin.m.u@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: mm-commits@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mike said:
: CONFIG_UBSAN_ALIGNMENT breaks x86-64 kernel with lockdep enabled, i.e.
: kernel with CONFIG_UBSAN_ALIGNMENT=y fails to load without even any error
: message.
:
: The problem is that ubsan callbacks use spinlocks and might be called
: before lockdep is initialized. Particularly this line in the
: reserve_ebda_region function causes problem:
:
: lowmem = *(unsigned short *)__va(BIOS_LOWMEM_KILOBYTES);
:
: If i put lockdep_init() before reserve_ebda_region call in
: x86_64_start_reservations kernel loads well.
Fix this ordering issue permanently: change lockdep so that it uses hlists
for the hash tables. Unlike a list_head, an hlist_head is in its
initialized state when it is all-zeroes, so lockdep is ready for operation
immediately upon boot - lockdep_init() need not have run.
The patch will also save some memory.
Probably lockdep_init() and lockdep_initialized can be done away with now.
Suggested-by: Mike Krinkin <krinkin.m.u@gmail.com>
Reported-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: mm-commits@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
schedstats is very useful during debugging and performance tuning but it
incurs overhead to calculate the stats. As such, even though it can be
disabled at build time, it is often enabled as the information is useful.
This patch adds a kernel command-line and sysctl tunable to enable or
disable schedstats on demand (when it's built in). It is disabled
by default as someone who knows they need it can also learn to enable
it when necessary.
The benefits are dependent on how scheduler-intensive the workload is.
If it is then the patch reduces the number of cycles spent calculating
the stats with a small benefit from reducing the cache footprint of the
scheduler.
These measurements were taken from a 48-core 2-socket
machine with Xeon(R) E5-2670 v3 cpus although they were also tested on a
single socket machine 8-core machine with Intel i7-3770 processors.
netperf-tcp
4.5.0-rc1 4.5.0-rc1
vanilla nostats-v3r1
Hmean 64 560.45 ( 0.00%) 575.98 ( 2.77%)
Hmean 128 766.66 ( 0.00%) 795.79 ( 3.80%)
Hmean 256 950.51 ( 0.00%) 981.50 ( 3.26%)
Hmean 1024 1433.25 ( 0.00%) 1466.51 ( 2.32%)
Hmean 2048 2810.54 ( 0.00%) 2879.75 ( 2.46%)
Hmean 3312 4618.18 ( 0.00%) 4682.09 ( 1.38%)
Hmean 4096 5306.42 ( 0.00%) 5346.39 ( 0.75%)
Hmean 8192 10581.44 ( 0.00%) 10698.15 ( 1.10%)
Hmean 16384 18857.70 ( 0.00%) 18937.61 ( 0.42%)
Small gains here, UDP_STREAM showed nothing intresting and neither did
the TCP_RR tests. The gains on the 8-core machine were very similar.
tbench4
4.5.0-rc1 4.5.0-rc1
vanilla nostats-v3r1
Hmean mb/sec-1 500.85 ( 0.00%) 522.43 ( 4.31%)
Hmean mb/sec-2 984.66 ( 0.00%) 1018.19 ( 3.41%)
Hmean mb/sec-4 1827.91 ( 0.00%) 1847.78 ( 1.09%)
Hmean mb/sec-8 3561.36 ( 0.00%) 3611.28 ( 1.40%)
Hmean mb/sec-16 5824.52 ( 0.00%) 5929.03 ( 1.79%)
Hmean mb/sec-32 10943.10 ( 0.00%) 10802.83 ( -1.28%)
Hmean mb/sec-64 15950.81 ( 0.00%) 16211.31 ( 1.63%)
Hmean mb/sec-128 15302.17 ( 0.00%) 15445.11 ( 0.93%)
Hmean mb/sec-256 14866.18 ( 0.00%) 15088.73 ( 1.50%)
Hmean mb/sec-512 15223.31 ( 0.00%) 15373.69 ( 0.99%)
Hmean mb/sec-1024 14574.25 ( 0.00%) 14598.02 ( 0.16%)
Hmean mb/sec-2048 13569.02 ( 0.00%) 13733.86 ( 1.21%)
Hmean mb/sec-3072 12865.98 ( 0.00%) 13209.23 ( 2.67%)
Small gains of 2-4% at low thread counts and otherwise flat. The
gains on the 8-core machine were slightly different
tbench4 on 8-core i7-3770 single socket machine
Hmean mb/sec-1 442.59 ( 0.00%) 448.73 ( 1.39%)
Hmean mb/sec-2 796.68 ( 0.00%) 794.39 ( -0.29%)
Hmean mb/sec-4 1322.52 ( 0.00%) 1343.66 ( 1.60%)
Hmean mb/sec-8 2611.65 ( 0.00%) 2694.86 ( 3.19%)
Hmean mb/sec-16 2537.07 ( 0.00%) 2609.34 ( 2.85%)
Hmean mb/sec-32 2506.02 ( 0.00%) 2578.18 ( 2.88%)
Hmean mb/sec-64 2511.06 ( 0.00%) 2569.16 ( 2.31%)
Hmean mb/sec-128 2313.38 ( 0.00%) 2395.50 ( 3.55%)
Hmean mb/sec-256 2110.04 ( 0.00%) 2177.45 ( 3.19%)
Hmean mb/sec-512 2072.51 ( 0.00%) 2053.97 ( -0.89%)
In constract, this shows a relatively steady 2-3% gain at higher thread
counts. Due to the nature of the patch and the type of workload, it's
not a surprise that the result will depend on the CPU used.
hackbench-pipes
4.5.0-rc1 4.5.0-rc1
vanilla nostats-v3r1
Amean 1 0.0637 ( 0.00%) 0.0660 ( -3.59%)
Amean 4 0.1229 ( 0.00%) 0.1181 ( 3.84%)
Amean 7 0.1921 ( 0.00%) 0.1911 ( 0.52%)
Amean 12 0.3117 ( 0.00%) 0.2923 ( 6.23%)
Amean 21 0.4050 ( 0.00%) 0.3899 ( 3.74%)
Amean 30 0.4586 ( 0.00%) 0.4433 ( 3.33%)
Amean 48 0.5910 ( 0.00%) 0.5694 ( 3.65%)
Amean 79 0.8663 ( 0.00%) 0.8626 ( 0.43%)
Amean 110 1.1543 ( 0.00%) 1.1517 ( 0.22%)
Amean 141 1.4457 ( 0.00%) 1.4290 ( 1.16%)
Amean 172 1.7090 ( 0.00%) 1.6924 ( 0.97%)
Amean 192 1.9126 ( 0.00%) 1.9089 ( 0.19%)
Some small gains and losses and while the variance data is not included,
it's close to the noise. The UMA machine did not show anything particularly
different
pipetest
4.5.0-rc1 4.5.0-rc1
vanilla nostats-v2r2
Min Time 4.13 ( 0.00%) 3.99 ( 3.39%)
1st-qrtle Time 4.38 ( 0.00%) 4.27 ( 2.51%)
2nd-qrtle Time 4.46 ( 0.00%) 4.39 ( 1.57%)
3rd-qrtle Time 4.56 ( 0.00%) 4.51 ( 1.10%)
Max-90% Time 4.67 ( 0.00%) 4.60 ( 1.50%)
Max-93% Time 4.71 ( 0.00%) 4.65 ( 1.27%)
Max-95% Time 4.74 ( 0.00%) 4.71 ( 0.63%)
Max-99% Time 4.88 ( 0.00%) 4.79 ( 1.84%)
Max Time 4.93 ( 0.00%) 4.83 ( 2.03%)
Mean Time 4.48 ( 0.00%) 4.39 ( 1.91%)
Best99%Mean Time 4.47 ( 0.00%) 4.39 ( 1.91%)
Best95%Mean Time 4.46 ( 0.00%) 4.38 ( 1.93%)
Best90%Mean Time 4.45 ( 0.00%) 4.36 ( 1.98%)
Best50%Mean Time 4.36 ( 0.00%) 4.25 ( 2.49%)
Best10%Mean Time 4.23 ( 0.00%) 4.10 ( 3.13%)
Best5%Mean Time 4.19 ( 0.00%) 4.06 ( 3.20%)
Best1%Mean Time 4.13 ( 0.00%) 4.00 ( 3.39%)
Small improvement and similar gains were seen on the UMA machine.
The gain is small but it stands to reason that doing less work in the
scheduler is a good thing. The downside is that the lack of schedstats and
tracepoints may be surprising to experts doing performance analysis until
they find the existence of the schedstats= parameter or schedstats sysctl.
It will be automatically activated for latencytop and sleep profiling to
alleviate the problem. For tracepoints, there is a simple warning as it's
not safe to activate schedstats in the context when it's known the tracepoint
may be wanted but is unavailable.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <mgalbraith@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1454663316-22048-1-git-send-email-mgorman@techsingularity.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Centralize gmux' ACPI HID in a header file and add apple_gmux_present().
This can be used by other drivers to activate quirks specific to dual
GPU MacBook Pros & Mac Pros. The alternative would be to hardcode DMI
or PCI IDs and amend them whenever Apple introduces a new machine.
Tested-by: Lukas Wunner <lukas@wunner.de>
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina 15"]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/89c23769058a340e5e11d4a7102f3793d3b0c94c.1452525860.git.lukas@wunner.de
Originally by Seth Forshee <seth.forshee@canonical.com>, 2012-10-04:
During graphics driver initialization it's useful to be able to mux
only the DDC to the inactive client in order to read the EDID. Add
a switch_ddc callback to allow capable handlers to provide this
functionality, and add vga_switcheroo_switch_ddc() to allow DRM
to mux only the DDC.
Modified by Dave Airlie <airlied@gmail.com>, 2012-12-22:
I can't figure out why I didn't like this, but I rewrote this [...]
to lock/unlock the ddc lines [...]. I think I'd prefer something
like that otherwise the interface got really ugly.
Modified by Lukas Wunner <lukas@wunner.de>, 2015-04 - 2015-10:
Change semantics of ->switch_ddc handler callback to return previous
DDC owner. Original version tried to determine previous DDC owner
with find_active_client() but this fails if the inactive client
registers before the active client.
Don't lock vgasr_mutex in _lock_ddc() / _unlock_ddc(), it can cause
deadlocks because (a) during switch (with vgasr_mutex already held),
GPU is woken and probes its outputs, tries to re-acquire vgasr_mutex
to lock DDC lines; (b) Likewise during switch, GPU is suspended and
calls cancel_delayed_work_sync() to stop output polling, if poll
task is running at this moment we may wait forever for it to finish.
Instead, lock mux_hw_lock when unregistering the handler because
the only reason why we'd want to lock vgasr_mutex in _lock_ddc() /
_unlock_ddc() is to block the handler from disappearing while DDC
lines are switched.
Also acquire mux_hw_lock in stage2 to avoid race condition where
reading the EDID and switching happens simultaneously. Likewise on
MIGD / MDIS commands and on runtime suspend.
v2.1: Overhaul locking, squash commits (Daniel Vetter)
v2.2: Readability improvements (Thierry Reding)
v2.3: Overhaul locking once more
v2.4: Retain semantics of ->switchto handler callback to switch all
pins, including DDC (Daniel Vetter)
v5: Rename ddc_lock to mux_hw_lock: Since we acquire this both
when calling ->switch_ddc and ->switchto, it protects not just
access to the DDC lines but to the mux in general. This is in
line with the DRM convention to use low-level locks to avoid
concurrent hw access (e.g. i2c, dp_aux) which are often called
hw_lock (Daniel Vetter)
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88861
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61115
Tested-by: Lukas Wunner <lukas@wunner.de>
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina 15"]
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/e81ae9722b84c5ed591805fee3ea6dbf5dc6c4b3.1452525860.git.lukas@wunner.de
Allow handlers to declare their capabilities and allow clients to
obtain that information. So far we have these use cases:
* If the handler is able to switch DDC separately, clients need to
probe EDID with drm_get_edid_switcheroo(). We should allow them
to detect a capable handler to ensure this function only gets
called when needed.
* Likewise if the handler is unable to switch AUX separately, the active
client needs to communicate link training parameters to the inactive
client, which may then skip the AUX handshake and set up its output
with these pre-calibrated values (DisplayPort specification v1.1a,
section 2.5.3.3). Clients need a way to recognize such a situation.
The flags for the radeon_atpx_handler and amdgpu_atpx_handler are
initially set to 0, this can later on be amended with
handler_flags |= VGA_SWITCHEROO_CAN_SWITCH_DDC;
when a ->switch_ddc callback is added.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88861
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61115
Tested-by: Lukas Wunner <lukas@wunner.de>
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina 15"]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/2b0d93ed6e511ca09e95e45e0b35627f330fabce.1452525860.git.lukas@wunner.de
GPIO chips have been around for years, but were never real devices,
instead they were piggy-backing on a parent device (such as a
platform_device or amba_device) but this was always optional.
GPIO chips could also exist without any device at all, with its
struct device *parent (ex *dev) pointer being set to null.
When sysfs was in use, a mock device would be created, with the
optional parent assigned, or just floating orphaned with NULL
as parent.
If sysfs is active, it will use this device as parent.
We now create a gpio_device struct containing a real
struct device and move the subsystem over to using that. The
list of struct gpio_chip:s is augmented to hold struct
gpio_device:s and we find gpio_chips:s by first looking up
the struct gpio_device.
The struct gpio_device is designed to stay around even if the
gpio_chip is removed, so as to satisfy users in userspace
that need a backing data structure to hold the state of the
session initiated with e.g. a character device even if there is
no physical chip anymore.
From this point on, gpiochips are devices.
Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Devices may have limits on the number of fragments in an skb they support.
Current codebase uses a constant as maximum for number of fragments one
skb can hold and use.
When enabling scatter/gather and running traffic with many small messages
the codebase uses the maximum number of fragments and may thereby violate
the max for certain devices.
The patch introduces a global variable as max number of fragments.
Signed-off-by: Hans Westgaard Ry <hans.westgaard.ry@oracle.com>
Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes range-based information used for optimizations in
begin_cpu_access and end_cpu_access.
We don't have any user nor implementation using range-based flush. It seems a
consensus that if we ever want something like that again (or even more robust
using 2D, 3D sub-range regions) we can use the upcoming dma-buf sync ioctl for
such.
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Tiago Vignatti <tiago.vignatti@intel.com>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1450820214-12509-3-git-send-email-tiago.vignatti@intel.com
This patch add max_burst to dma_get_slave_caps for clients
to get the burst capability of slave dma controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add a helper function devm_add_action_or_reset() which will internally
call devm_add_action(). But if devm_add_action() fails then it will
execute the action mentioned and return the error code.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
See http: //www.infradead.org/rpr.html
X-Evolution-Source: 1451162204.2173.11@leira.trondhjem.org
Content-Transfer-Encoding: 8bit
Mime-Version: 1.0
We support OFFSET_MAX just fine, so don't round down below it. Also
switch to using min_t to make the helper more readable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: 433c92379d ("NFS: Clean up nfs_size_to_loff_t()")
Cc: stable@vger.kernel.org # 2.6.23+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
