The scale tests are verifying behavior of mlxsw when number of instances of
some resource reaches the ASIC capacity. The number of instances is
referred to as "target" number.
No scale tests so far needed to know this target number to clean up. E.g.
the tc_flower simply removes the clsact qdisc that all the tested filters
are hooked onto, and that takes care of collecting all the filters.
However, for the RIF counter test, which is being added in a future patch,
VLAN netdevices are created. These are created as part of the test, but of
course the cleanup needs to undo them again. For that it needs to know how
many there were. To support this usage, pass the target number to the
cleanup callback.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scale tests are currently testing two things: that some number of
instances of a given resource can actually be created; and that when an
attempt is made to create more than the supported amount, the failures are
noted and handled gracefully.
Sometimes the scale test depends on more than one resource. In particular,
a following patch will add a RIF counter scale test, which depends on the
number of RIF counters that can be bound, and also on the number of RIFs
that can be created.
When the test is limited by the auxiliary resource and not by the primary
one, there's no point trying to run the overflow test, because it would be
testing exhaustion of the wrong resource.
To support this use case, when the $test_get_target yields 0, skip the test
instead.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scale tests are currently testing two things: that some number of
instances of a given resource can actually be created; and that when an
attempt is made to create more than the supported amount, the failures are
noted and handled gracefully.
However the ability to allocate the resource does not mean that the
resource actually works when passing traffic. For that, make it possible
for a given scale to also test traffic.
Traffic test is only run on the positive leg of the scale test (no point
trying to pass traffic when the expected outcome is that the resource will
not be allocated). Traffic tests are opt-in, if a given test does not
expose it, it is not run.
To this end, delay the test cleanup until after the traffic test is run.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scale of each resource is tested in the following manner:
1. The scale target is queried.
2. The test setup is prepared.
3. The test is invoked.
In some cases, the occupancy of a resource changes as part of the second
step, requiring the test to return a scale target that takes this change
into account.
Make this more robust by re-querying the scale target after the second
step.
Another possible solution is to swap the first and second steps, but
when a test needs to be skipped (i.e., scale target is zero), the setup
would have been in vain.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using mlxsw driver, the configurations are offloaded just in case that
there is a physical port which is enslaved to the virtual device
(e.g., to a bridge). In 'mirror_gre_bridge_1q_lag' test, the bridge gets an
address and route before there are ports in the bridge. It means that these
configurations are not offloaded.
Till now the test passes with mlxsw driver even that the RIF of the
bridge is not in the hardware, because the ARP packets are trapped in
layer 2 and also mirrored, so there is no real need of the RIF in hardware.
The previous patch changed the traps 'ARP_REQUEST' and 'ARP_RESPONSE' to
be done at layer 3 instead of layer 2. With this change the ARP packets are
not trapped during the test, as the RIF is not in the hardware because of
the order of configurations.
Reorder the configurations to make them to be offloaded, then the test will
pass with the change of the traps.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Spectrum ASIC has a limit on how many L3 devices (called RIFs) can be
created. The limit depends on the ASIC and FW revision, and mlxsw reads it
from the FW. In order to communicate both the number of RIFs that there can
be, and how many are taken now (i.e. occupancy), introduce a corresponding
devlink resource.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to expose number of RIFs as a resource, it is going to be handy
to have the number of currently-allocated RIFs as a single number.
Introduce such.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the traps 'ARP_REQUEST' and 'ARP_RESPONSE' occur at layer 2.
To allow the packets to be flooded, they are configured with the action
'MIRROR_TO_CPU' which means that the CPU receives a replica of the packet.
Today, Spectrum ASICs also support trapping ARP packets at layer 3. This
behavior is better, then the packets can just be trapped and there is no
need to mirror them. An additional motivation is that using the traps at
layer 2, the ARP packets are dropped in the router as they do not have an
IP header, then they are counted as error packets, which might confuse
users.
Add the relevant traps for layer 3 and use them instead of the existing
traps. There is no visible change to user space.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
tcp: final (?) round of mem pressure fixes
While working on prior patch series (e10b02ee5b "Merge branch
'net-reduce-tcp_memory_allocated-inflation'"), I found that we
could still have frozen TCP flows under memory pressure.
I thought we had solved this in 2015, but the fix was not complete.
v2: deal with zerocopy tx paths.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Blamed commit only dealt with applications issuing small writes.
Issue here is that we allow to force memory schedule for the sk_buff
allocation, but we have no guarantee that sendmsg() is able to
copy some payload in it.
In this patch, I make sure the socket can use up to tcp_wmem[0] bytes.
For example, if we consider tcp_wmem[0] = 4096 (default on x86),
and initial skb->truesize being 1280, tcp_sendmsg() is able to
copy up to 2816 bytes under memory pressure.
Before this patch a sendmsg() sending more than 2816 bytes
would either block forever (if persistent memory pressure),
or return -EAGAIN.
For bigger MTU networks, it is advised to increase tcp_wmem[0]
to avoid sending too small packets.
v2: deal with zero copy paths.
Fixes: 8e4d980ac2 ("tcp: fix behavior for epoll edge trigger")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Blamed commit only dealt with applications issuing small writes.
Issue here is that we allow to force memory schedule for the sk_buff
allocation, but we have no guarantee that sendmsg() is able to
copy some payload in it.
In this patch, I make sure the socket can use up to tcp_wmem[0] bytes.
For example, if we consider tcp_wmem[0] = 4096 (default on x86),
and initial skb->truesize being 1280, tcp_sendmsg() is able to
copy up to 2816 bytes under memory pressure.
Before this patch a sendmsg() sending more than 2816 bytes
would either block forever (if persistent memory pressure),
or return -EAGAIN.
For bigger MTU networks, it is advised to increase tcp_wmem[0]
to avoid sending too small packets.
v2: deal with zero copy paths.
Fixes: 8e4d980ac2 ("tcp: fix behavior for epoll edge trigger")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_forced_mem_schedule() has a bug similar to ones fixed
in commit 7c80b038d2 ("net: fix sk_wmem_schedule() and
sk_rmem_schedule() errors")
While this bug has little chance to trigger in old kernels,
we need to fix it before the following patch.
Fixes: d83769a580 ("tcp: fix possible deadlock in tcp_send_fin()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Upton has agreed to help with reviewing the KVM/arm64
patches, and has been doing so for a while now, so adding him
as to the reviewer list.
Note that Oliver is using a different email address for this
purpose, rather than the one his been using for his other
contributions.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Oliver Upton <oupton@google.com>
Link: https://lore.kernel.org/r/20220616085318.1303657-1-maz@kernel.org
The current code does not check for errors and does not release the
reference on errors.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220616222910.136854-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The existing code uses pm_runtime_get_sync/put_autosuspend, but
pm_runtime was not explicitly enabled. The autosuspend delay was not
set either, the value is set to 5s since HDMI is rather painful to
resume.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220616222910.136854-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616220559.136160-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The UpExtreme BIOS reports microphones that are not physically
present, so this module ends-up selecting SOF, while the UpExtreme11
BIOS does not report microphones so the snd-hda-intel driver is
selected.
For consistency use SOF unconditionally in autodetection mode. The use
of the snd-hda-intel driver can still be enabled with
'options snd-intel-dspcfg dsp_driver=1'
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220616201029.130477-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recent change brings potential leak of value on kernel stack to userspace
due to uninitialized value.
This commit fixes the bug.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: baa914cd81 ("firewire: add kernel API to access CYCLE_TIME register")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220512112037.103142-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
LLVM's lld linker doesn't have a universal architecture support (e.g.,
it definitely doesn't work on s390x), so be safe and force lld for
urandom_read and liburandom_read.so only on x86 architectures.
This should fix s390x CI runs.
Fixes: 3e6fe5ce4d ("libbpf: Fix internal USDT address translation logic for shared libraries")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220617045512.1339795-1-andrii@kernel.org
Add flags value to check the result of ata completion
Fixes: 255c03d15a ("libata: Add tracepoints")
Cc: stable@vger.kernel.org
Signed-off-by: Edward Wu <edwardwu@realtek.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Maxim Mikityanskiy says:
====================
The first patch of this series is a documentation fix.
The second patch allows BPF helpers to accept memory regions of fixed
size without doing runtime size checks.
The two next patches add new functionality that allows XDP to
accelerate iptables synproxy.
v1 of this series [1] used to include a patch that exposed conntrack
lookup to BPF using stable helpers. It was superseded by series [2] by
Kumar Kartikeya Dwivedi, which implements this functionality using
unstable helpers.
The third patch adds new helpers to issue and check SYN cookies without
binding to a socket, which is useful in the synproxy scenario.
The fourth patch adds a selftest, which includes an XDP program and a
userspace control application. The XDP program uses socketless SYN
cookie helpers and queries conntrack status instead of socket status.
The userspace control application allows to tune parameters of the XDP
program. This program also serves as a minimal example of usage of the
new functionality.
The last two patches expose the new helpers to TC BPF and extend the
selftest.
The draft of the new functionality was presented on Netdev 0x15 [3].
v2 changes:
Split into two series, submitted bugfixes to bpf, dropped the conntrack
patches, implemented the timestamp cookie in BPF using bpf_loop, dropped
the timestamp cookie patch.
v3 changes:
Moved some patches from bpf to bpf-next, dropped the patch that changed
error codes, split the new helpers into IPv4/IPv6, added verifier
functionality to accept memory regions of fixed size.
v4 changes:
Converted the selftest to the test_progs runner. Replaced some
deprecated functions in xdp_synproxy userspace helper.
v5 changes:
Fixed a bug in the selftest. Added questionable functionality to support
new helpers in TC BPF, added selftests for it.
v6 changes:
Wrap the new helpers themselves into #ifdef CONFIG_SYN_COOKIES, replaced
fclose with pclose and fixed the MSS for IPv6 in the selftest.
v7 changes:
Fixed the off-by-one error in indices, changed the section name to
"xdp", added missing kernel config options to vmtest in CI.
v8 changes:
Properly rebased, dropped the first patch (the same change was applied
by someone else), updated the cover letter.
v9 changes:
Fixed selftests for no_alu32.
v10 changes:
Selftests for s390x were blacklisted due to lack of support of kfunc,
rebased the series, split selftests to separate commits, created
ARG_PTR_TO_FIXED_SIZE_MEM and packed arg_size, addressed the rest of
comments.
[1]: https://lore.kernel.org/bpf/20211020095815.GJ28644@breakpoint.cc/t/
[2]: https://lore.kernel.org/bpf/20220114163953.1455836-1-memxor@gmail.com/
[3]: https://netdevconf.info/0x15/session.html?Accelerating-synproxy-with-XDP
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This commit extends selftests for the new BPF helpers
bpf_tcp_raw_{gen,check}_syncookie_ipv{4,6} to also test the TC BPF
functionality added in the previous commit.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220615134847.3753567-7-maximmi@nvidia.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This commit allows the new BPF helpers to work in SKB context (in TC
BPF programs): bpf_tcp_raw_{gen,check}_syncookie_ipv{4,6}.
Using these helpers in TC BPF programs is not recommended, because it's
unlikely that the BPF program will provide any substantional speedup
compared to regular SYN cookies or synproxy, after the SKB is already
created.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220615134847.3753567-6-maximmi@nvidia.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This commit adds selftests for the new BPF helpers:
bpf_tcp_raw_{gen,check}_syncookie_ipv{4,6}.
xdp_synproxy_kern.c is a BPF program that generates SYN cookies on
allowed TCP ports and sends SYNACKs to clients, accelerating synproxy
iptables module.
xdp_synproxy.c is a userspace control application that allows to
configure the following options in runtime: list of allowed ports, MSS,
window scale, TTL.
A selftest is added to prog_tests that leverages the above programs to
test the functionality of the new helpers.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220615134847.3753567-5-maximmi@nvidia.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The new helpers bpf_tcp_raw_{gen,check}_syncookie_ipv{4,6} allow an XDP
program to generate SYN cookies in response to TCP SYN packets and to
check those cookies upon receiving the first ACK packet (the final
packet of the TCP handshake).
Unlike bpf_tcp_{gen,check}_syncookie these new helpers don't need a
listening socket on the local machine, which allows to use them together
with synproxy to accelerate SYN cookie generation.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220615134847.3753567-4-maximmi@nvidia.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Before this commit, the BPF verifier required ARG_PTR_TO_MEM arguments
to be followed by ARG_CONST_SIZE holding the size of the memory region.
The helpers had to check that size in runtime.
There are cases where the size expected by a helper is a compile-time
constant. Checking it in runtime is an unnecessary overhead and waste of
BPF registers.
This commit allows helpers to accept pointers to memory without the
corresponding ARG_CONST_SIZE, given that they define the memory region
size in struct bpf_func_proto and use ARG_PTR_TO_FIXED_SIZE_MEM type.
arg_size is unionized with arg_btf_id to reduce the kernel image size,
and it's valid because they are used by different argument types.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220615134847.3753567-3-maximmi@nvidia.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
bpf_tcp_gen_syncookie expects the full length of the TCP header (with
all options), and bpf_tcp_check_syncookie accepts lengths bigger than
sizeof(struct tcphdr). Fix the documentation that says these lengths
should be exactly sizeof(struct tcphdr).
While at it, fix a typo in the name of struct ipv6hdr.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220615134847.3753567-2-maximmi@nvidia.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Raju Lakkaraju says:
====================
net: lan743x: PCI11010 / PCI11414 devices Enhancements
This patch series continues with the addition of supported features
for the Ethernet function of the PCI11010 / PCI11414 devices to
the LAN743x driver.
====================
Link: https://lore.kernel.org/r/20220616041226.26996-1-Raju.Lakkaraju@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support to Master-Slave configuration and state
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add SGMII access read and write functions
Add support to SGMII 1G and 2.5G for PCI11010/PCI11414 chips
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support to Magic Packet Detection with Secure-ON for PCI11010/PCI11414 chips
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support to LAN743x common register dump
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alvin Šipraga says:
====================
net: dsa: realtek: rtl8365mb: improve handling of PHY modes
This series introduces some minor cleanup of the driver and improves the
handling of PHY interface modes to break the assumption that CPU ports
are always over an external interface, and the assumption that user
ports are always using an internal PHY.
====================
Link: https://lore.kernel.org/r/20220615225116.432283-1-alvin@pqrs.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Realtek switches in the rtl8365mb family always have at least one port
with a so-called external interface, supporting PHY interface modes such
as RGMII or SGMII. The purpose of this patch is to improve the driver's
handling of these ports.
A new struct rtl8365mb_chip_info is introduced together with a static
array of such structs. An instance of this struct is added for each
supported switch, distinguished by its chip ID and version. Embedded in
each chip_info struct is an array of struct rtl8365mb_extint, describing
the external interfaces available. This is more specific than the old
rtl8365mb_extint_port_map, which was only valid for switches with up to
6 ports.
The struct rtl8365mb_extint also contains a bitmask of supported PHY
interface modes, which allows the driver to distinguish which ports
support RGMII. This corrects a previous mistake in the driver whereby it
was assumed that any port with an external interface supports RGMII.
This is not actually the case: for example, the RTL8367S has two
external interfaces, only the second of which supports RGMII. The first
supports only SGMII and HSGMII. This new design will make it easier to
add support for other interface modes.
Finally, rtl8365mb_phylink_get_caps() is fixed up to return supported
capabilities based on the external interface properties described above.
This addresses Vladimir's point in the linked thread that the
capabilities are not actually a function of the DSA port type: Although
most typical applications will treat the ports with internal PHY as user
ports, there is no actual hardware limitation preventing one from using
them as a CPU port. Equally, ports with external interface(s) may well
be treated as user ports, even though it is typical to use those ports
as CPU ports.
Link: https://lore.kernel.org/netdev/20220510192301.5djdt3ghoavxulhl@bang-olufsen.dk/
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable is just assigned the value of a macro, so it can be
removed.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The maximum number of ports is actually 11, according to two
observations:
1. The highest port ID used in the vendor driver is 10. Since port IDs
are indexed from 0, and since DSA follows the same numbering system,
this means up to 11 ports are to be presumed.
2. The registers with port mask fields always amount to a maximum port
mask of 0x7FF, corresponding to a maximum 11 ports.
In view of this, I also deleted the comment.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no real need for this variable: the line change interrupt mask
is sufficiently masked out when getting linkup_ind and linkdown_ind in
the interrupt handler.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The official name of this switch is RTL8367RB-VB, not RTL8367RB. There
is also an RTL8367RB-VC which is rather different. Change the name of
the CHIP_ID/_VER macros for reasons of consistency.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder says:
====================
net: ipa: more multi-channel event ring work
This series makes a little more progress toward supporting multiple
channels with a single event ring. The first removes the assumption
that consecutive events are associated with the same RX channel.
The second derives the channel associated with an event from the
event itself, and the next does a small cleanup enabled by that.
The fourth causes updates to occur for every event processed (rather
once). And the final patch does a little more rework to make TX
completion have more in common with RX completion.
====================
Link: https://lore.kernel.org/r/20220615165929.5924-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the processing done for TX channels in gsi_channel_update()
into gsi_evt_ring_rx_update(). The called function is called for
both RX and TX channels, so rename it to be gsi_evt_ring_update().
As a result, this code no longer assumes events in an event ring are
associated with just one channel.
Because all events in a ring are handled in that function, we can
move the call to gsi_trans_move_complete() there, and can ring the
event ring doorbell there as well after all new events in the ring
have been processed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When an RX transaction completes, we update the trans->len field to
contain the actual number of bytes received. This is done in a loop
in gsi_evt_ring_rx_update().
Change that function so it checks the data transfer direction
recorded in the transaction, and only updates trans->len for RX
transfers.
Then call it unconditionally. This means events for TX endpoints
will run through the loop without otherwise doing anything, but
this will change shortly.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The only reason the event ring's channel pointer is needed in
gsi_evt_ring_rx_update() is so we can get at its GSI pointer.
We can pass the GSI pointer as an argument, along with the event
ring ID, and thereby avoid using the event ring channel pointer.
This is another step toward no longer assuming an event ring
services a single channel.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change gsi_channel_trans_map() so it derives the channel used from
the transaction. Pass the index of the *first* TRE used by the
transaction, and have the called function account for the fact that
the last one used is what's important.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In gsi_evt_ring_rx_update(), use gsi_event_trans() repeatedly
to find the transaction associated with an event, rather than
assuming consecutive events are associated with the same channel.
This removes the only caller of gsi_trans_pool_next(), so get rid
of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rasmus Villemoes says:
====================
dt-bindings: dp83867: add binding for io_impedance_ctrl nvmem cell
We have a board where measurements indicate that the current three
options - leaving IO_IMPEDANCE_CTRL at the reset value (which is
factory calibrated to a value corresponding to approximately 50 ohms)
or using one of the two boolean properties to set it to the min/max
value - are too coarse.
This series adds a device tree binding for an nvmem cell which can be
populated during production with a suitable value calibrated for each
board, and corresponding support in the driver. The second patch adds
a trivial phy wrapper for dev_err_probe(), used in the third.
====================
Link: https://lore.kernel.org/r/20220614084612.325229-1-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have a board where measurements indicate that the current three
options - leaving IO_IMPEDANCE_CTRL at the (factory calibrated) reset
value or using one of the two boolean properties to set it to the
min/max value - are too coarse.
Implement support for the newly added binding allowing device tree to
specify an nvmem cell containing an appropriate value for this
specific board.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dev_err_probe() function is quite useful to avoid boilerplate
related to -EPROBE_DEFER handling. Add a phydev_err_probe() helper to
simplify making use of that from phy drivers which otherwise use the
phydev_* helpers.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
