Here are some small IIO driver fixes for reported problems for 5.14-rc6
(no staging driver fixes at the moment).
All of them resolve reported issues and have been in linux-next all week
with no reported problems. Full details are in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYRfzsg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn4qACdG4OZ4cn8C2QtsxXMtxknUcBeKMYAoIv2x+bB
gl/bJVn9vtyVqSESnefM
=OOPX
-----END PGP SIGNATURE-----
Merge tag 'staging-5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO driver fixes from Greg KH:
"Here are some small IIO driver fixes for reported problems for
5.14-rc6 (no staging driver fixes at the moment).
All of them resolve reported issues and have been in linux-next all
week with no reported problems. Full details are in the shortlog"
* tag 'staging-5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: adc: Fix incorrect exit of for-loop
iio: humidity: hdc100x: Add margin to the conversion time
dt-bindings: iio: st: Remove wrong items length check
iio: accel: fxls8962af: fix i2c dependency
iio: adis: set GPIO reset pin direction
iio: adc: ti-ads7950: Ensure CS is deasserted after reading channels
iio: accel: fxls8962af: fix potential use of uninitialized symbol
Pull i2c fixes from Wolfram Sang:
"One driver bugfix, a documentation bugfix, and an "uninitialized data"
leak fix for the core"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Documentation: i2c: add i2c-sysfs into index
i2c: dev: zero out array used for i2c reads from userspace
i2c: iproc: fix race between client unreg and tasklet
Object files used to link .tmp_vmlinux.kallsyms1 have many
R_PPC64_ADDR64 relocations in non-SHF_WRITE sections. There are many
text relocations (e.g. in .rela___ksymtab_gpl+* and .rela__mcount_loc
sections) in a -pie link and are disallowed by LLD:
ld.lld: error: can't create dynamic relocation R_PPC64_ADDR64 against local symbol in readonly segment; recompile object files with -fPIC or pass '-Wl,-z,notext' to allow text relocations in the output
>>> defined in arch/powerpc/kernel/head_64.o
>>> referenced by arch/powerpc/kernel/head_64.o:(__restart_table+0x10)
Newer GNU ld configured with "--enable-textrel-check=error" will report
an error as well:
$ ld-new -EL -m elf64lppc -pie ... -o .tmp_vmlinux.kallsyms1 ...
ld-new: read-only segment has dynamic relocations
Add "-z notext" to suppress the errors. Non-CONFIG_RELOCATABLE builds
use the default -no-pie mode and thus R_PPC64_ADDR64 relocations can be
resolved at link-time.
Reported-by: Itaru Kitayama <itaru.kitayama@riken.jp>
Co-developed-by: Bill Wendling <morbo@google.com>
Signed-off-by: Fangrui Song <maskray@google.com>
Signed-off-by: Bill Wendling <morbo@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210813200511.1905703-1-morbo@google.com
Using asm goto in __WARN_FLAGS() and WARN_ON() allows more
flexibility to GCC.
For that add an entry to the exception table so that
program_check_exception() knowns where to resume execution
after a WARNING.
Here are two exemples. The first one is done on PPC32 (which
benefits from the previous patch), the second is on PPC64.
unsigned long test(struct pt_regs *regs)
{
int ret;
WARN_ON(regs->msr & MSR_PR);
return regs->gpr[3];
}
unsigned long test9w(unsigned long a, unsigned long b)
{
if (WARN_ON(!b))
return 0;
return a / b;
}
Before the patch:
000003a8 <test>:
3a8: 81 23 00 84 lwz r9,132(r3)
3ac: 71 29 40 00 andi. r9,r9,16384
3b0: 40 82 00 0c bne 3bc <test+0x14>
3b4: 80 63 00 0c lwz r3,12(r3)
3b8: 4e 80 00 20 blr
3bc: 0f e0 00 00 twui r0,0
3c0: 80 63 00 0c lwz r3,12(r3)
3c4: 4e 80 00 20 blr
0000000000000bf0 <.test9w>:
bf0: 7c 89 00 74 cntlzd r9,r4
bf4: 79 29 d1 82 rldicl r9,r9,58,6
bf8: 0b 09 00 00 tdnei r9,0
bfc: 2c 24 00 00 cmpdi r4,0
c00: 41 82 00 0c beq c0c <.test9w+0x1c>
c04: 7c 63 23 92 divdu r3,r3,r4
c08: 4e 80 00 20 blr
c0c: 38 60 00 00 li r3,0
c10: 4e 80 00 20 blr
After the patch:
000003a8 <test>:
3a8: 81 23 00 84 lwz r9,132(r3)
3ac: 71 29 40 00 andi. r9,r9,16384
3b0: 40 82 00 0c bne 3bc <test+0x14>
3b4: 80 63 00 0c lwz r3,12(r3)
3b8: 4e 80 00 20 blr
3bc: 0f e0 00 00 twui r0,0
0000000000000c50 <.test9w>:
c50: 7c 89 00 74 cntlzd r9,r4
c54: 79 29 d1 82 rldicl r9,r9,58,6
c58: 0b 09 00 00 tdnei r9,0
c5c: 7c 63 23 92 divdu r3,r3,r4
c60: 4e 80 00 20 blr
c70: 38 60 00 00 li r3,0
c74: 4e 80 00 20 blr
In the first exemple, we see GCC doesn't need to duplicate what
happens after the trap.
In the second exemple, we see that GCC doesn't need to emit a test
and a branch in the likely path in addition to the trap.
We've got some WARN_ON() in .softirqentry.text section so it needs
to be added in the OTHER_TEXT_SECTIONS in modpost.c
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/389962b1b702e3c78d169e59bcfac56282889173.1618331882.git.christophe.leroy@csgroup.eu
After patch 54efd50 (block: make generic_make_request handle
arbitrarily sized bios), the IO through io-throttle may be larger,
and these IOs may be further split into more small IOs. However,
IOPS throttle does not seem to be aware of this change, which
makes the calculation of IOPS of large IOs incomplete, resulting
in disk-side IOPS that does not meet expectations. Maybe we should
fix this problem.
We can reproduce it by set max_sectors_kb of disk to 128, set
blkio.write_iops_throttle to 100, run a dd instance inside blkio
and use iostat to watch IOPS:
dd if=/dev/zero of=/dev/sdb bs=1M count=1000 oflag=direct
As a result, without this change the average IOPS is 1995, with
this change the IOPS is 98.
Signed-off-by: Chunguang Xu <brookxu@tencent.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/65869aaad05475797d63b4c3fed4f529febe3c26.1627876014.git.brookxu@tencent.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Lightnvm supports the OCSSD 1.x and 2.0 specs which were early attempts
to produce Open Channel SSDs and never made it into the NVMe spec
proper. They have since been superceeded by NVMe enhancements such
as ZNS support. Remove the support per the deprecation schedule.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210812132308.38486-1-hch@lst.de
Reviewed-by: Matias Bjørling <mb@lightnvm.io>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If an SQPOLL based ring is newly created and an application issues an
io_uring_enter(2) system call on it, then we can return a spurious
-EOWNERDEAD error. This happens because there's nothing to submit, and
if the caller doesn't specify any other action, the initial error
assignment of -EOWNERDEAD never gets overwritten. This causes us to
return it directly, even if it isn't valid.
Move the error assignment into the actual failure case instead.
Cc: stable@vger.kernel.org
Fixes: d9d05217cb ("io_uring: stop SQPOLL submit on creator's death")
Reported-by: Sherlock Holo sherlockya@gmail.com
Link: https://github.com/axboe/liburing/issues/413
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYReBzAAKCRCAXGG7T9hj
vsjcAQD9tV9ThjOP9HXL3lGGoSIBCy+t92ZwpVkQuYITa9fHFAD/ViU+Iye5WHTf
jWxlveDJMoOegEmpKEQAoX56hDHPkww=
=lQOv
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.14-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"A small cleanup patch and a fix of a rare race in the Xen evtchn
driver"
* tag 'for-linus-5.14-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: Fix race in set_evtchn_to_irq
xen/events: remove redundant initialization of variable irq
* A fix to avoid passing -mno-relax to compilers that don't support it.
* A comment fix.
-----BEGIN PGP SIGNATURE-----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=4Fkm
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- avoid passing -mno-relax to compilers that don't support it
- a comment fix
* tag 'riscv-for-linus-5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix comment regarding kernel mapping overlapping with IS_ERR_VALUE
riscv: kexec: do not add '-mno-relax' flag if compiler doesn't support it
- fix to revert to the historic write behavior (Bart Van Assche)
-----BEGIN PGP SIGNATURE-----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=dsC9
-----END PGP SIGNATURE-----
Merge tag 'configfs-5.14' of git://git.infradead.org/users/hch/configfs
Pull configfs fix from Christoph Hellwig:
- fix to revert to the historic write behavior (Bart Van Assche)
* tag 'configfs-5.14' of git://git.infradead.org/users/hch/configfs:
configfs: restore the kernel v5.13 text attribute write behavior
The Tegra soctherm driver prints message about the clamped temperature
trip each time when thermal core disables the low/high trip. The message
is confusing and creates illusion that driver is malfunctioning. Turn that
noisy info message into a debug message.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210712002353.17276-1-digetx@gmail.com
Even though the previous binding made it a required child node, the
implementation in Linux never made it mandatory and just ignored thermal
zones without trip points.
This was even effectively encouraged, since the thermal core wouldn't
allow a thermal sensor to probe without a thermal zone.
In the case where you had a thermal device that had multiple sensors but
with enough knowledge to provide trip points for only a few of them,
this meant that the only way to make that driver probe was to provide a
thermal zone without the trips node required by the binding.
This obviously led to a fair number of device trees doing exactly that,
making the initial binding requirement ineffective.
Let's make it clear by dropping that requirement.
Cc: Amit Kucheria <amitk@kernel.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-pm@vger.kernel.org
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210721140424.725744-34-maxime@cerno.tech
There are two pairs of declarations for thermal_cooling_device_register()
and thermal_of_cooling_device_register(), and only one set was changed
in a recent patch, so the other one now causes a compile-time warning:
drivers/net/wireless/mediatek/mt76/mt7915/init.c: In function 'mt7915_thermal_init':
drivers/net/wireless/mediatek/mt76/mt7915/init.c:134:48: error: passing argument 1 of 'thermal_cooling_device_register' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
134 | cdev = thermal_cooling_device_register(wiphy_name(wiphy), phy,
| ^~~~~~~~~~~~~~~~~
In file included from drivers/net/wireless/mediatek/mt76/mt7915/init.c:7:
include/linux/thermal.h:407:39: note: expected 'char *' but argument is of type 'const char *'
407 | thermal_cooling_device_register(char *type, void *devdata,
| ~~~~~~^~~~
Change the dummy helper functions to have the same arguments as the
normal version.
Fixes: f991de53a8 ("thermal: make device_register's type argument const")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210722090717.1116748-1-arnd@kernel.org
Some chrome platform requires IMOK method in coreboot. But these platforms
don't use GDDV data vault in coreboot. As per current code flow, to enable
and use IMOK only, we need to have GDDV support as well in coreboot. This
patch removes the dependency for IMOK from GDDV to enable and use IMOK
independently.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210716163946.3142-1-sumeet.r.pawnikar@intel.com
Default to prefixed pkg-config when crosscompiling, this matches what
other parts of the tools/ directory already do.
[dlezcano] : Reworked description
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/31302992.qZodDJZGDc@devpool47
- Remove empty macros assignments
- Use directory creation parameter for the install tool
- Use $OBJ instead of building the list of object for the 'clean' target
[dlezcano] : Changed title and description
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1951386.ZPQrlMDjM2@devpool47
commit <47595e3286> ("<MAINTAINERS: Mark some staging directories>")
indicated the ipx network layer as obsolete in Jan 2018,
updated in the MAINTAINERS file.
now, after being exposed for 3 years to refactoring, so to
remove the ipx network layer info from MAINTAINERS.
additionally, there is no module that depends on ipx.h
except a broken staging driver(r8188eu)
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit <47595e3286> ("<MAINTAINERS: Mark some staging directories>")
indicated the ipx network layer as obsolete in Jan 2018,
updated in the MAINTAINERS file
now, after being exposed for 3 years to refactoring, so to
delete uapi/linux/ipx.h and net/ipx.h header files for good.
additionally, there is no module that depends on ipx.h except
a broken staging driver(r8188eu)
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder says:
====================
net: ipa: last things before PM conversion
This series contains a few remaining changes needed before fully
switching over to using runtime power management rather than the
previous "IPA clock" mechanism.
The first patch moves the calls to enable and disable the IPA
interrupt as a system wakeup interrupt into "ipa_clock.c" with the
rest of the power-related code.
The second adds a flag to make it possible to distinguish runtime
suspend from system suspend.
The third and fourth patches arrange for the ->start_xmit path to
resume hardware if necessary, to ensure it is powered. If power is
not active, the TX queue is stopped, and arrangements are made for
the queue to be restarted once hardware power is active again.
The fifth patch keeps the TX queue active during suspend. This
isn't necessary for system suspend but it's important for runtime
suspend.
And the last patch makes it so we don't hold the hardware active
while the modem network device is open.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a clock reference is taken whenever the ->ndo_open
callback for the modem netdev is called. That reference is dropped
when the device is closed, in ipa_stop().
We no longer need this, because ipa_start_xmit() now handles the
situation where the hardware power state is not active.
Drop the clock reference in ipa_open() when we're done, and take a
new reference in ipa_stop() before we begin closing the interface.
Finally (and unrelated, but trivial), change the return type of
ipa_start_xmit() to be netdev_tx_t instead of int.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we stop the modem netdev transmit queue when suspending
the hardware. For system suspend this ensured we'd never attempt
to transmit while attempting to suspend the modem endpoints.
For runtime suspend, the IPA hardware might get suspended while the
system is operating. In that case we want an attempt to transmit a
packet to cause the hardware to resume if necessary. But if we
disable the queue this cannot happen.
So stop disabling the queue on suspend. In case we end up disabling
it in ipa_start_xmit() (see the previous commit), we still arrange
to start the TX queue on resume.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure the hardware is powered when we transmit a packet.
But if it's not, we can't block to wait for it. So asynchronously
request power in ipa_start_xmit(), and only proceed if the return
value indicates the power state is active.
If the hardware is not active, a runtime resume request will have
been initiated. In that case, stop the network stack from further
transmit attempts until the resume completes. Return NETDEV_TX_BUSY,
to retry sending the packet once the queue is restarted.
If the power request returns an error (other than -EINPROGRESS,
which just means a resume requested elsewhere isn't complete), just
drop the packet.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new work structure in the modem private data, and use it to
re-enable the modem network device transmit queue when resuming.
This is needed by the next patch, which stops the TX queue if IPA
power isn't active when a transmit request arrives. Packets will
start arriving the instant the TX queue is enabled, but resuming
isn't complete until ipa_modem_resume() returns. This way we're
sure to be resumed before transmits are allowed again.
Cancel it before calling ipa_stop() in ipa_modem_stop() to ensure
the transmit queue restart completes before it gets stopped there.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new flag that is set when the hardware is suspended due to a
system suspend operation, distingishing it from runtime suspend.
Use it in the SUSPEND IPA interrupt handler to determine whether to
trigger a system resume because of the event. Define new suspend
and resume power management callback functions to set and clear the
new flag, respectively.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the call to enable the IPA interrupt as a wakeup interrupt into
ipa_power_setup(), disable it in ipa_power_teardown().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov says:
====================
net: bridge: mcast: dump querier state
This set adds the ability to dump the current multicast querier state.
This is extremely useful when debugging multicast issues, we've had
many cases of unexpected queriers causing strange behaviour and mcast
test failures. The first patch changes the querier struct to record
a port device's ifindex instead of a pointer to the port itself so we
can later retrieve it, I chose this way because it's much simpler
and doesn't require us to do querier port ref counting, it is best
effort anyway. Then patch 02 makes the querier address/port updates
consistent via a combination of multicast_lock and seqcount, so readers
can only use seqcount to get a consistent snapshot of address and port.
Patch 03 is a minor cleanup in preparation for the dump support, it
consolidates IPv4 and IPv6 querier selection paths as they share most of
the logic (except address comparisons of course). Finally the last three
patches add the new querier state dumping support, for the bridge's
global multicast context we embed the BRIDGE_QUERIER_xxx attributes
into IFLA_BR_MCAST_QUERIER_STATE and for the per-vlan global mcast
contexts we embed them into BRIDGE_VLANDB_GOPTS_MCAST_QUERIER_STATE.
The structure is:
[IFLA_BR_MCAST_QUERIER_STATE / BRIDGE_VLANDB_GOPTS_MCAST_QUERIER_STATE]
`[BRIDGE_QUERIER_IP_ADDRESS] - ip address of the querier
`[BRIDGE_QUERIER_IP_PORT] - bridge port ifindex where the querier was
seen (set only if external querier)
`[BRIDGE_QUERIER_IP_OTHER_TIMER] - other querier timeout
`[BRIDGE_QUERIER_IPV6_ADDRESS] - ip address of the querier
`[BRIDGE_QUERIER_IPV6_PORT] - bridge port ifindex where the querier
was seen (set only if external querier)
`[BRIDGE_QUERIER_IPV6_OTHER_TIMER] - other querier timeout
Later we can also add IGMP version of seen queriers and last seen values
from the queries.
====================
Use the new mcast querier state dump infrastructure and export vlans'
mcast context querier state embedded in attribute
BRIDGE_VLANDB_GOPTS_MCAST_QUERIER_STATE.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dumping global IPv6 querier state, we dump the state
only if our own querier is enabled or there has been another external
querier which has won the election. For the bridge global state we use
a new attribute IFLA_BR_MCAST_QUERIER_STATE and embed the state inside.
The structure is:
[IFLA_BR_MCAST_QUERIER_STATE]
`[BRIDGE_QUERIER_IPV6_ADDRESS] - ip address of the querier
`[BRIDGE_QUERIER_IPV6_PORT] - bridge port ifindex where the querier
was seen (set only if external querier)
`[BRIDGE_QUERIER_IPV6_OTHER_TIMER] - other querier timeout
IPv4 and IPv6 attributes are embedded at the same level of
IFLA_BR_MCAST_QUERIER_STATE. If we didn't dump anything we cancel the nest
and return.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dumping global IPv4 querier state, we dump the state
only if our own querier is enabled or there has been another external
querier which has won the election. For the bridge global state we use
a new attribute IFLA_BR_MCAST_QUERIER_STATE and embed the state inside.
The structure is:
[IFLA_BR_MCAST_QUERIER_STATE]
`[BRIDGE_QUERIER_IP_ADDRESS] - ip address of the querier
`[BRIDGE_QUERIER_IP_PORT] - bridge port ifindex where the querier was
seen (set only if external querier)
`[BRIDGE_QUERIER_IP_OTHER_TIMER] - other querier timeout
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can consolidate both functions as they share almost the same logic.
This is easier to maintain and we have a single querier update function.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a sequence counter to make sure port/address updates can be read
consistently without requiring the bridge multicast_lock. We need to
zero out the port and address when the other querier has expired and
we're about to select ourselves as querier. br_multicast_read_querier
will be used later when dumping querier state. Updates are done only
with the multicast spinlock and softirqs disabled, while reads are done
from process context and from softirqs (due to notifications).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when a querier port is detected its net_bridge_port pointer is
recorded, but it's used only for comparisons so it's fine to have stale
pointer, in order to dereference and use the port pointer a proper
accounting of its usage must be implemented adding unnecessary
complexity. To solve the problem we can just store the netdevice ifindex
instead of the port pointer and retrieve the bridge port. It is a best
effort and the device needs to be validated that is still part of that
bridge before use, but that is small price to pay for avoiding querier
reference counting for each port/vlan.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky says:
====================
Devlink cleanup for delay event series
Jakub's request to make sure that devlink events are delayed and not
printed till they fully accessible [1] requires us to implement delayed
event notification system in the devlink.
In order to do it, I moved some of my patches (xarray e.t.c) from the future
series to be before "Move devlink_register to be near devlink_reload_enable" [2].
That allows us to rely on DEVLINK_REGISTERED xarray mark to decide if to print
event or not.
Other patches are simple cleanup which is needed anyway.
[1] https://lore.kernel.org/lkml/20210811071817.4af5ab34@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com
[2] https://lore.kernel.org/lkml/cover.1628599239.git.leonro@nvidia.com
Next in the queue:
* Delay event series
* Move devlink_register to be near devlink_reload_enable"
* Extension of devlink_ops to be set dynamically
* devlink_reload_* delete
* Devlink locks rework to user xarray and reference counting
* ????
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink pointer always exists after hclge_devlink_init() succeed.
Remove that check together with NULL setting after release and ensure
that devlink_register is last command prior to call to devlink_reload_enable().
Fixes: b741269b27 ("net: hns3: add support for registering devlink for PF")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The { 0 } doesn't clear all fields in the struct, but tells to the
compiler to set all fields to zero and doesn't touch any sub-fields
if they exists.
The {} is an empty initialiser that instructs to fully initialize whole
struct including sub-fields, which is error-prone for future
devlink_flash_notify extensions.
Fixes: 6700acc5f1 ("devlink: collect flash notify params into a struct")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use xarray instead of linearly organized linked lists for the
devlink instances. This will let us revise the locking scheme in favour
of internal xarray locking that protects database.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct devlink itself is protected by internal lock and doesn't
need global lock during operation. That global lock is used to protect
addition/removal new devlink instances from the global list in use by
all devlink consumers in the system.
The future conversion of linked list to be xarray will allow us to
actually delete that lock, but first we need to count all struct devlink
users.
The reference counting provides us a way to ensure that no new user
space commands success to grab devlink instance which is going to be
destroyed makes it is safe to access it without lock.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink objects are accessible only after they were registered and
have valid devlink_*->devlink pointers.
Remove that check and simplify respective fill functions as an outcome
of such change.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink_pernet_pre_exit() will be called if net namespace exits.
That routine is relevant for devlink instances that were assigned to
that namespaces first. This assignment is possible only with the following
command: "devlink reload DEV netns ...", which already checks reload support.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
powerpc BUG_ON() and WARN_ON() are based on using twnei instruction.
For catching simple conditions like a variable having value 0, this
is efficient because it does the test and the trap at the same time.
But most conditions used with BUG_ON or WARN_ON are more complex and
forces GCC to format the condition into a 0 or 1 value in a register.
This will usually require 2 to 3 instructions.
The most efficient solution would be to use __builtin_trap() because
GCC is able to optimise the use of the different trap instructions
based on the requested condition, but this is complex if not
impossible for the following reasons:
- __builtin_trap() is a non-recoverable instruction, so it can't be
used for WARN_ON
- Knowing which line of code generated the trap would require the
analysis of DWARF information. This is not a feature we have today.
As mentioned in commit 8d4fbcfbe0 ("Fix WARN_ON() on bitfield ops")
the way WARN_ON() is implemented is suboptimal. That commit also
mentions an issue with 'long long' condition. It fixed it for
WARN_ON() but the same problem still exists today with BUG_ON() on
PPC32. It will be fixed by using the generic implementation.
By using the generic implementation, gcc will naturally generate a
branch to the unconditional trap generated by BUG().
As modern powerpc implement zero-cycle branch,
that's even more efficient.
And for the functions using WARN_ON() and its return, the test
on return from WARN_ON() is now also used for the WARN_ON() itself.
On PPC64 we don't want it because we want to be able to use CFAR
register to track how we entered the code that trapped. The CFAR
register would be clobbered by the branch.
A simple test function:
unsigned long test9w(unsigned long a, unsigned long b)
{
if (WARN_ON(!b))
return 0;
return a / b;
}
Before the patch:
0000046c <test9w>:
46c: 7c 89 00 34 cntlzw r9,r4
470: 55 29 d9 7e rlwinm r9,r9,27,5,31
474: 0f 09 00 00 twnei r9,0
478: 2c 04 00 00 cmpwi r4,0
47c: 41 82 00 0c beq 488 <test9w+0x1c>
480: 7c 63 23 96 divwu r3,r3,r4
484: 4e 80 00 20 blr
488: 38 60 00 00 li r3,0
48c: 4e 80 00 20 blr
After the patch:
00000468 <test9w>:
468: 2c 04 00 00 cmpwi r4,0
46c: 41 82 00 0c beq 478 <test9w+0x10>
470: 7c 63 23 96 divwu r3,r3,r4
474: 4e 80 00 20 blr
478: 0f e0 00 00 twui r0,0
47c: 38 60 00 00 li r3,0
480: 4e 80 00 20 blr
So we see before the patch we need 3 instructions on the likely path
to handle the WARN_ON(). With the patch the trap goes on the unlikely
path.
See below the difference at the entry of system_call_exception where
we have several BUG_ON(), allthough less impressing.
With the patch:
00000000 <system_call_exception>:
0: 81 6a 00 84 lwz r11,132(r10)
4: 90 6a 00 88 stw r3,136(r10)
8: 71 60 00 02 andi. r0,r11,2
c: 41 82 00 70 beq 7c <system_call_exception+0x7c>
10: 71 60 40 00 andi. r0,r11,16384
14: 41 82 00 6c beq 80 <system_call_exception+0x80>
18: 71 6b 80 00 andi. r11,r11,32768
1c: 41 82 00 68 beq 84 <system_call_exception+0x84>
20: 94 21 ff e0 stwu r1,-32(r1)
24: 93 e1 00 1c stw r31,28(r1)
28: 7d 8c 42 e6 mftb r12
...
7c: 0f e0 00 00 twui r0,0
80: 0f e0 00 00 twui r0,0
84: 0f e0 00 00 twui r0,0
Without the patch:
00000000 <system_call_exception>:
0: 94 21 ff e0 stwu r1,-32(r1)
4: 93 e1 00 1c stw r31,28(r1)
8: 90 6a 00 88 stw r3,136(r10)
c: 81 6a 00 84 lwz r11,132(r10)
10: 69 60 00 02 xori r0,r11,2
14: 54 00 ff fe rlwinm r0,r0,31,31,31
18: 0f 00 00 00 twnei r0,0
1c: 69 60 40 00 xori r0,r11,16384
20: 54 00 97 fe rlwinm r0,r0,18,31,31
24: 0f 00 00 00 twnei r0,0
28: 69 6b 80 00 xori r11,r11,32768
2c: 55 6b 8f fe rlwinm r11,r11,17,31,31
30: 0f 0b 00 00 twnei r11,0
34: 7d 8c 42 e6 mftb r12
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b286e07fb771a664b631cd07a40b09c06f26e64b.1618331881.git.christophe.leroy@csgroup.eu
Patches related to the tmon which is in tools/thermal are floating around
since years because it is unclear who takes care of it.
Add the missing userspace tools directory related to thermal to fix the
situation.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
signed math causes generation of costlier instructions such as DIV when
they could be done by barrerl shifter.
Worse part is this is not caught by things like bloat-o-meter since
instruction length / symbols are typically same size.
e.g.
stock (signed math)
__________________
919b4614 <test_taint>:
919b4614: div r2,r0,0x20
^^^
919b4618: add2 r2,0x920f6050,r2
919b4620: ld_s r2,[r2,0]
919b4622: lsr r0,r2,r0
919b4626: j_s.d [blink]
919b4628: bmsk_s r0,r0,0
919b462a: nop_s
(patched) unsigned math
__________________
919b4614 <test_taint>:
919b4614: lsr r2,r0,0x5 @nr/32
^^^
919b4618: add2 r2,0x920f6050,r2
919b4620: ld_s r2,[r2,0]
919b4622: lsr r0,r2,r0 #test_bit()
919b4626: j_s.d [blink]
919b4628: bmsk_s r0,r0,0
919b462a: nop_s
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().
Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Amit Kucheria <amitk@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210803141621.780504-20-bigeasy@linutronix.de
The TSC id and number of TSC ids should be stored as unsigned int as
they can't be negative. Fix the datatype of the loop counter 'i' and
rcar_gen3_thermal_tsc.id to reflect this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210804091818.2196806-3-niklas.soderlund+renesas@ragnatech.se
This extends the struct power_supply_battery_info with a
"technology" field makes the core DT parser optionally obtain
this from the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
All supported hardware except V3U is capable of generating interrupts
to the CPU when the temperature go below or above a set value. Use this
to implement support for the set_trip() feature of the thermal core on
supported hardware.
The V3U have its interrupts routed to the ECM module and therefore can
not be used to implement set_trip() as the driver can't be made aware of
when the interrupt triggers.
Each TSC is capable of tracking up-to three different temperatures while
only two are needed to implement the tracking of the thermal window.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210804091818.2196806-2-niklas.soderlund+renesas@ragnatech.se
