This converts the tps65086.txt binding description to YAML schema so
dts files can be verified automatically.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 8f00b3c41a ("mfd: db8500-prcmu: Rename register header") renames
dbx500-prcmu-regs.h to db8500-prcmu-regs.h in drivers/mfd/ but misses
to adjust the ARM/NOMADIK/Ux500 ARCHITECTURES section in MAINTAINERS.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains:
warning: no file matches F: drivers/mfd/dbx500*
Remove the obsolete file entry after this file renaming.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch cleanups below cppcheck warning.
sound/soc/soc-ac97.c:41:15: style: struct member 'snd_ac97_gpio_priv::gpios_set' is never used. [unusedStructMember]
unsigned int gpios_set;
^
sound/soc/soc-ac97.c:42:28: style: struct member 'snd_ac97_gpio_priv::component' is never used. [unusedStructMember]
struct snd_soc_component *component;
^
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r1euyolk.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleanups below cppcheck warning.
sound/soc/soc-component.c:1183:9: style: The scope of the variable 'ret' can be reduced. [variableScope]
int i, ret;
^
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87sfzayolo.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleanups below cppcheck warning.
sound/soc/soc-jack.c:21:6: style: struct member 'jack_gpio_tbl::count' is never used. [unusedStructMember]
int count;
^
sound/soc/soc-jack.c:23:28: style: struct member 'jack_gpio_tbl::gpios' is never used. [unusedStructMember]
struct snd_soc_jack_gpio *gpios;
^
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tujqyols.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleanups below cppcheck warning.
sound/soc/soc-jack.c:45:6: style: The scope of the variable 'enable' can be reduced. [variableScope]
int enable;
^
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v946yolx.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleanups below cppcheck warning.
sound/soc/soc-dai.c:553:13: style: Variable 'ret' is assigned a value that is never used. [unreadVariable]
int i, ret = 0;
^
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87wnomyom1.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleanups below cppcheck warning.
sound/soc/soc-dai.c:454:7: style: The scope of the variable 'supported_cpu' can be reduced. [variableScope]
bool supported_cpu;
^
sound/soc/soc-dai.c:455:7: style: The scope of the variable 'supported_codec' can be reduced. [variableScope]
bool supported_codec;
^
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87y292yom6.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleanups below cppcheck warning.
sound/soc/soc-generic-dmaengine-pcm.c:310:6: style: The scope of the variable 'ret' can be reduced. [variableScope]
int ret;
^
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87zgtiyomb.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleanups below cppcheck warning.
sound/soc/soc-generic-dmaengine-pcm.c:233:28: style: The scope of the variable 'substream' can be reduced. [variableScope]
struct snd_pcm_substream *substream;
^
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/871r6u0yzs.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleanups below cppcheck warning.
sound/soc/soc-generic-dmaengine-pcm.c:82:6: style: The scope of the variable 'ret' can be reduced. [variableScope]
int ret;
^
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/8735ra0yzz.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When clearing the chip-select mask, the controller will switch to chip
selecting the native CS0 line. Because the control register chip-select
mask is not updated in a single write this will cause undesirable
chip-selection of CS0 even when requesting to select other native
chip-select lines. This is additionally problematic as the chip-select
may still be asserted. With the ARMADA 38x SoC the controller will
assert both the desired native chip-select and CS0.
To avoid any undesirable behaviour with the chip-select lines, update
the control register with a single write. This avoids selecting CS0 and
causes the (de-)assert to apply at the same time.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Link: https://lore.kernel.org/r/20210816050228.3223661-1-nathan@nathanrossi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In 69de4421bb ("drm/ttm: Initialize debugfs from
ttm_global_init()"), ttm_global_init was changed so that if creation
of the debugfs global root directory fails, ttm_global_init will bail
out early and return an error, leading to initialization failure of
DRM drivers. However, not every system will be using debugfs. On such
a system, debugfs directory creation can be expected to fail, but DRM
drivers must still be usable. This changes it so that if creation of
TTM's debugfs root directory fails, then no biggie: keep calm and
carry on.
Fixes: 69de4421bb ("drm/ttm: Initialize debugfs from ttm_global_init()")
Signed-off-by: Dan Moulding <dmoulding@me.com>
Tested-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210810195906.22220-2-dmoulding@me.com
Signed-off-by: Christian König <christian.koenig@amd.com>
Cross-rename lacks a check when that would prevent exchanging a
directory and subvolume from different parent subvolume. This causes
data inconsistencies and is caught before commit by tree-checker,
turning the filesystem to read-only.
Calling the renameat2 with RENAME_EXCHANGE flags like
renameat2(AT_FDCWD, namesrc, AT_FDCWD, namedest, (1 << 1))
on two paths:
namesrc = dir1/subvol1/dir2
namedest = subvol2/subvol3
will cause key order problem with following write time tree-checker
report:
[1194842.307890] BTRFS critical (device loop1): corrupt leaf: root=5 block=27574272 slot=10 ino=258, invalid previous key objectid, have 257 expect 258
[1194842.322221] BTRFS info (device loop1): leaf 27574272 gen 8 total ptrs 11 free space 15444 owner 5
[1194842.331562] BTRFS info (device loop1): refs 2 lock_owner 0 current 26561
[1194842.338772] item 0 key (256 1 0) itemoff 16123 itemsize 160
[1194842.338793] inode generation 3 size 16 mode 40755
[1194842.338801] item 1 key (256 12 256) itemoff 16111 itemsize 12
[1194842.338809] item 2 key (256 84 2248503653) itemoff 16077 itemsize 34
[1194842.338817] dir oid 258 type 2
[1194842.338823] item 3 key (256 84 2363071922) itemoff 16043 itemsize 34
[1194842.338830] dir oid 257 type 2
[1194842.338836] item 4 key (256 96 2) itemoff 16009 itemsize 34
[1194842.338843] item 5 key (256 96 3) itemoff 15975 itemsize 34
[1194842.338852] item 6 key (257 1 0) itemoff 15815 itemsize 160
[1194842.338863] inode generation 6 size 8 mode 40755
[1194842.338869] item 7 key (257 12 256) itemoff 15801 itemsize 14
[1194842.338876] item 8 key (257 84 2505409169) itemoff 15767 itemsize 34
[1194842.338883] dir oid 256 type 2
[1194842.338888] item 9 key (257 96 2) itemoff 15733 itemsize 34
[1194842.338895] item 10 key (258 12 256) itemoff 15719 itemsize 14
[1194842.339163] BTRFS error (device loop1): block=27574272 write time tree block corruption detected
[1194842.339245] ------------[ cut here ]------------
[1194842.443422] WARNING: CPU: 6 PID: 26561 at fs/btrfs/disk-io.c:449 csum_one_extent_buffer+0xed/0x100 [btrfs]
[1194842.511863] CPU: 6 PID: 26561 Comm: kworker/u17:2 Not tainted 5.14.0-rc3-git+ #793
[1194842.511870] Hardware name: empty empty/S3993, BIOS PAQEX0-3 02/24/2008
[1194842.511876] Workqueue: btrfs-worker-high btrfs_work_helper [btrfs]
[1194842.511976] RIP: 0010:csum_one_extent_buffer+0xed/0x100 [btrfs]
[1194842.512068] RSP: 0018:ffffa2c284d77da0 EFLAGS: 00010282
[1194842.512074] RAX: 0000000000000000 RBX: 0000000000001000 RCX: ffff928867bd9978
[1194842.512078] RDX: 0000000000000000 RSI: 0000000000000027 RDI: ffff928867bd9970
[1194842.512081] RBP: ffff92876b958000 R08: 0000000000000001 R09: 00000000000c0003
[1194842.512085] R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000
[1194842.512088] R13: ffff92875f989f98 R14: 0000000000000000 R15: 0000000000000000
[1194842.512092] FS: 0000000000000000(0000) GS:ffff928867a00000(0000) knlGS:0000000000000000
[1194842.512095] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[1194842.512099] CR2: 000055f5384da1f0 CR3: 0000000102fe4000 CR4: 00000000000006e0
[1194842.512103] Call Trace:
[1194842.512128] ? run_one_async_free+0x10/0x10 [btrfs]
[1194842.631729] btree_csum_one_bio+0x1ac/0x1d0 [btrfs]
[1194842.631837] run_one_async_start+0x18/0x30 [btrfs]
[1194842.631938] btrfs_work_helper+0xd5/0x1d0 [btrfs]
[1194842.647482] process_one_work+0x262/0x5e0
[1194842.647520] worker_thread+0x4c/0x320
[1194842.655935] ? process_one_work+0x5e0/0x5e0
[1194842.655946] kthread+0x135/0x160
[1194842.655953] ? set_kthread_struct+0x40/0x40
[1194842.655965] ret_from_fork+0x1f/0x30
[1194842.672465] irq event stamp: 1729
[1194842.672469] hardirqs last enabled at (1735): [<ffffffffbd1104f5>] console_trylock_spinning+0x185/0x1a0
[1194842.672477] hardirqs last disabled at (1740): [<ffffffffbd1104cc>] console_trylock_spinning+0x15c/0x1a0
[1194842.672482] softirqs last enabled at (1666): [<ffffffffbdc002e1>] __do_softirq+0x2e1/0x50a
[1194842.672491] softirqs last disabled at (1651): [<ffffffffbd08aab7>] __irq_exit_rcu+0xa7/0xd0
The corrupted data will not be written, and filesystem can be unmounted
and mounted again (all changes since the last commit will be lost).
Add the missing check for new_ino so that all non-subvolumes must reside
under the same parent subvolume. There's an exception allowing to
exchange two subvolumes from any parents as the directory representing a
subvolume is only a logical link and does not have any other structures
related to the parent subvolume, unlike files, directories etc, that
are always in the inode namespace of the parent subvolume.
Fixes: cdd1fedf82 ("btrfs: add support for RENAME_EXCHANGE and RENAME_WHITEOUT")
CC: stable@vger.kernel.org # 4.7+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The Maxim 17042-family of fuel gauges are often embedded in other Maxim
chips, e.g. in Maxim 77693 which is a companion power management IC.
In such designs there might be actually two interrupts:
- INTB signaling change from charger, flash or MUIC,
- ALERT signaling change from fuel gauge.
Describe the interrupt in bindings to make it clear it is about the fuel
gauge ALERT interrupt, not the INT.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
All bits of STATUS register are already defined (see STATUS_SMN_BIT and
further) so there is no need to define status SoC threshold min/max
values one more time.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reading status register can fail in the interrupt handler. In such
case, the regmap_read() will not store anything useful under passed
'val' variable and random stack value will be used to determine type of
interrupt.
Handle the regmap_read() failure to avoid handling interrupt type and
triggering changed power supply event based on random stack value.
Fixes: 39e7213edc ("max17042_battery: Support regmap to access device's registers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Adding ethtool per-queue statistics support to show number of interrupts
generated at DMA tx and DMA rx. All the counters are incremented at
dwmac4_dma_interrupt function.
Signed-off-by: Vijayakannan Ayyathurai <vijayakannan.ayyathurai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding generic ethtool per-queue statistic framework to display the
statistics for each rx/tx queue. In future, users can avail it to add
more per-queue specific counters. Number of rx/tx queues displayed is
depending on the available rx/tx queues in that particular MAC config
and this number is limited up to the MTL_MAX_{RX|TX}_QUEUES defined
in the driver.
Ethtool per-queue statistic display will look like below, when users
start adding more counters.
Example:
q0_tx_statA:
q0_tx_statB:
q0_tx_statC:
|
q0_tx_statX:
.
.
.
qMAX_tx_statA:
qMAX_tx_statB:
qMAX_tx_statC:
|
qMAX_tx_statX:
q0_rx_statA:
q0_rx_statB:
q0_rx_statC:
|
q0_rx_statX:
.
.
.
qMAX_rx_statA:
qMAX_rx_statB:
qMAX_rx_statC:
|
qMAX_rx_statX:
In addition, this patch has the support on displaying the number of
packets received and transmitted per queue.
Signed-off-by: Vijayakannan Ayyathurai <vijayakannan.ayyathurai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA channel status "Transmit buffer unavailable(TBU)" bit is not
considered as a successful dma tx. Hence, it should not affect
all the irq count statistic.
Fixes: 1103d3a553 ("net: stmmac: dwmac4: Also use TBU interrupt to clean TX path")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Vijayakannan Ayyathurai <vijayakannan.ayyathurai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: 2 bug fixes
The first one disables aRFS/NTUPLE on an older broken firmware version.
The second one adds missing memory barriers related to completion ring
handling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Each completion ring entry has a valid bit to indicate that the entry
contains a valid completion event. The driver's main poll loop
__bnxt_poll_work() has the proper dma_rmb() to make sure the valid
bit of the next entry has been checked before proceeding further.
But when we call bnxt_rx_pkt() to process the RX event, the RX
completion event consists of two completion entries and only the
first entry has been checked to be valid. We need the same barrier
after checking the next completion entry. Add missing dma_rmb()
barriers in bnxt_rx_pkt() and other similar locations.
Fixes: 67a95e2022 ("bnxt_en: Need memory barrier when processing the completion ring.")
Reported-by: Lance Richardson <lance.richardson@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Lance Richardson <lance.richardson@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
212 firmware broke aRFS, so disable it. Traffic may stop after ntuple
filters are inserted and deleted by the 212 firmware.
Fixes: ae10ae740a ("bnxt_en: Add new hardware RFS mode.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver's initialization and teardown sequence is a chaotic
mess that has gathered a lot of cruft over time. It works because there
is no strict dependency between the functions, but it could be improved.
The basic principle that teardown should be the exact reverse of setup
is obviously not held. We have initialization steps (sja1105_tas_setup,
sja1105_flower_setup) in the probe method that are torn down in the DSA
.teardown method instead of driver unbind time.
We also have code after the dsa_register_switch() call, which implicitly
means after the .setup() method has finished, which is pretty unusual.
Also, sja1105_teardown() has calls set up in a different order than the
error path of sja1105_setup(): see the reversed ordering between
sja1105_ptp_clock_unregister and sja1105_mdiobus_unregister.
Also, sja1105_static_config_load() is called towards the end of
sja1105_setup(), but sja1105_static_config_free() is also towards the
end of the error path and teardown path. The static_config_load() call
should be earlier.
Also, making and breaking the connections between struct sja1105_port
and struct dsa_port could be refactored into dedicated functions, makes
the code easier to follow.
We move some code from the DSA .setup() method into the probe method,
like the device tree parsing, and we move some code from the probe
method into the DSA .setup() method to be symmetric with its placement
in the DSA .teardown() method, which is nice because the unbind function
has a single call to dsa_unregister_switch(). Example of the latter type
of code movement are the connections between ports mentioned above, they
are now in the .setup() method.
Finally, due to fact that the kthread_init_worker() call is no longer
in sja1105_probe() - located towards the bottom of the file - but in
sja1105_setup() - located much higher - there is an inverse ordering
with the worker function declaration, sja1105_port_deferred_xmit. To
avoid that, the entire sja1105_setup() and sja1105_teardown() functions
are moved towards the bottom of the file.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a possible null-pointer dereference in qed_rdma_create_qp().
Changes from V2:
- Revert checkpatch fixes.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoiding qed ll2 race condition and NULL pointer dereference as part
of the remove and recovery flows.
Changes form V1:
- Change (!p_rx->set_prod_addr).
- qed_ll2.c checkpatch fixes.
Change from V2:
- Revert "qed_ll2.c checkpatch fixes".
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the function to reflect what it's doing. Also add a description
of the register values as kindly provided by Realtek.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__tipc_sendmsg() is called to send SYN packet by either tipc_sendmsg()
or tipc_connect(). The difference is in tipc_connect(), it will call
tipc_wait_for_connect() after __tipc_sendmsg() to wait until connecting
is done. So there's no need to wait in __tipc_sendmsg() for this case.
This patch is to fix it by calling tipc_wait_for_connect() only when dlen
is not 0 in __tipc_sendmsg(), which means it's called by tipc_connect().
Note this also fixes the failure in tipcutils/test/ptts/:
# ./tipcTS &
# ./tipcTC 9
(hang)
Fixes: 36239dab6da7 ("tipc: fix implicit-connect for SYN+")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Convert ocelot to phylink
The ocelot switchdev and felix dsa drivers are interesting because they
target the same class of hardware switches but used in different modes.
Colin has an interesting use case where he wants to use a hardware
switch supported by the ocelot switchdev driver with the felix dsa
driver.
So far, the existing hardware revisions were similar between the ocelot
and felix drivers, but not completely identical. With identical hardware,
it is absurd that the felix driver uses phylink while the ocelot driver
uses phylib - this should not be one of the differences between the
switchdev and dsa driver, and we could eliminate it.
Colin will need the common phylink support in ocelot and felix when
adding a phylink_pcs driver for the PCS1G block inside VSC7514, which
will make the felix driver work with either the NXP or the Microchip PCS.
As usual, Alex, Horatiu, sorry for bugging you, but it would be
appreciated if you could give this a quick run on actual VSC7514
hardware (which I don't have) to make sure I'm not introducing any
breakage.
====================
Fixes: 0f06a6787e ("samples: Add an IPv6 "-6" option to the pktgen scripts")
Signed-off-by: David S. Miller <davem@davemloft.net>
The felix DSA driver, which is a wrapper over the same hardware class as
ocelot, is integrated with phylink, but ocelot is using the plain PHY
library. It makes sense to bring together the two implementations, which
is what this patch achieves.
This is a large patch and hard to break up, but it does the following:
The existing ocelot_adjust_link writes some registers, and
felix_phylink_mac_link_up writes some registers, some of them are
common, but both functions write to some registers to which the other
doesn't.
The main reasons for this are:
- Felix switches so far have used an NXP PCS so they had no need to
write the PCS1G registers that ocelot_adjust_link writes
- Felix switches have the MAC fixed at 1G, so some of the MAC speed
changes actually break the link and must be avoided.
The naming conventions for the functions introduced in this patch are:
- vsc7514_phylink_{mac_config,validate} are specific to the Ocelot
instantiations and placed in ocelot_net.c which is built only for the
ocelot switchdev driver.
- ocelot_phylink_mac_link_{up,down} are shared between the ocelot
switchdev driver and the felix DSA driver (they are put in the common
lib).
One by one, the registers written by ocelot_adjust_link are:
DEV_MAC_MODE_CFG - felix_phylink_mac_link_up had no need to write this
register since its out-of-reset value was fine and
did not need changing. The write is moved to the
common ocelot_phylink_mac_link_up and on felix it is
guarded by a quirk bit that makes the written value
identical with the out-of-reset one
DEV_PORT_MISC - runtime invariant, was moved to vsc7514_phylink_mac_config
PCS1G_MODE_CFG - same as above
PCS1G_SD_CFG - same as above
PCS1G_CFG - same as above
PCS1G_ANEG_CFG - same as above
PCS1G_LB_CFG - same as above
DEV_MAC_ENA_CFG - both ocelot_adjust_link and ocelot_port_disable
touched this. felix_phylink_mac_link_{up,down} also
do. We go with what felix does and put it in
ocelot_phylink_mac_link_up.
DEV_CLOCK_CFG - ocelot_adjust_link and felix_phylink_mac_link_up both
write this, but to different values. Move to the common
ocelot_phylink_mac_link_up and make sure via the quirk
that the old values are preserved for both.
ANA_PFC_PFC_CFG - ocelot_adjust_link wrote this, felix_phylink_mac_link_up
did not. Runtime invariant, speed does not matter since
PFC is disabled via the RX_PFC_ENA bits which are cleared.
Move to vsc7514_phylink_mac_config.
QSYS_SWITCH_PORT_MODE_PORT_ENA - both ocelot_adjust_link and
felix_phylink_mac_link_{up,down} wrote
this. Ocelot also wrote this register
from ocelot_port_disable. Keep what
felix did, move in ocelot_phylink_mac_link_{up,down}
and delete ocelot_port_disable.
ANA_POL_FLOWC - same as above
SYS_MAC_FC_CFG - same as above, except slight behavior change. Whereas
ocelot always enabled RX and TX flow control, felix
listened to phylink (for the most part, at least - see
the 2500base-X comment).
The registers which only felix_phylink_mac_link_up wrote are:
SYS_PAUSE_CFG_PAUSE_ENA - this is why I am not sure that flow control
worked on ocelot. Not it should, since the
code is shared with felix where it does.
ANA_PORT_PORT_CFG - this is a Frame Analyzer block register, phylink
should be the one touching them, deleted.
Other changes:
- The old phylib registration code was in mscc_ocelot_init_ports. It is
hard to work with 2 levels of indentation already in, and with hard to
follow teardown logic. The new phylink registration code was moved
inside ocelot_probe_port(), right between alloc_etherdev() and
register_netdev(). It could not be done before (=> outside of)
ocelot_probe_port() because ocelot_probe_port() allocates the struct
ocelot_port which we then use to assign ocelot_port->phy_mode to. It
is more preferable to me to have all PHY handling logic inside the
same function.
- On the same topic: struct ocelot_port_private :: serdes is only used
in ocelot_port_open to set the SERDES protocol to Ethernet. This is
logically a runtime invariant and can be done just once, when the port
registers with phylink. We therefore don't even need to keep the
serdes reference inside struct ocelot_port_private, or to use the devm
variant of of_phy_get().
- Phylink needs a valid phy-mode for phylink_create() to succeed, and
the existing device tree bindings in arch/mips/boot/dts/mscc/ocelot_pcb120.dts
don't define one for the internal PHY ports. So we patch
PHY_INTERFACE_MODE_NA into PHY_INTERFACE_MODE_INTERNAL.
- There was a strategically placed:
switch (priv->phy_mode) {
case PHY_INTERFACE_MODE_NA:
continue;
which made the code skip the serdes initialization for the internal
PHY ports. Frankly that is not all that obvious, so now we explicitly
initialize the serdes under an "if" condition and not rely on code
jumps, so everything is clearer.
- There was a write of OCELOT_SPEED_1000 to DEV_CLOCK_CFG for QSGMII
ports. Since that is in fact the default value for the register field
DEV_CLOCK_CFG_LINK_SPEED, I can only guess the intention was to clear
the adjacent fields, MAC_TX_RST and MAC_RX_RST, aka take the port out
of reset, which does match the comment. I don't even want to know why
this code is placed there, but if there is indeed an issue that all
ports that share a QSGMII lane must all be up, then this logic is
already buggy, since mscc_ocelot_init_ports iterates using
for_each_available_child_of_node, so nobody prevents the user from
putting a 'status = "disabled";' for some QSGMII ports which would
break the driver's assumption.
In any case, in the eventuality that I'm right, we would have yet
another issue if ocelot_phylink_mac_link_down would reset those ports
and that would be forbidden, so since the ocelot_adjust_link logic did
not do that (maybe for a reason), add another quirk to preserve the
old logic.
The ocelot driver teardown goes through all ports in one fell swoop.
When initialization of one port fails, the ocelot->ports[port] pointer
for that is reset to NULL, and teardown is done only for non-NULL ports,
so there is no reason to do partial teardowns, let the central
mscc_ocelot_release_ports() do its job.
Tested bind, unbind, rebind, link up, link down, speed change on mock-up
hardware (modified the driver to probe on Felix VSC9959). Also
regression tested the felix DSA driver. Could not test the Ocelot
specific bits (PCS1G, SERDES, device tree bindings).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_port_enable touches ANA_PORT_PORT_CFG, which has the following
fields:
- LOCKED_PORTMOVE_CPU, LEARNDROP, LEARNCPU, LEARNAUTO, RECV_ENA, all of
which are written with their hardware default values, also runtime
invariants. So it makes no sense to write these during every .ndo_open.
- PORTID_VAL: this field has an out-of-reset value of zero for all ports
and must be initialized by software. Additionally, the
ocelot_setup_logical_port_ids() code path sets up different logical
port IDs for the ports in a hardware LAG, and we absolutely don't want
.ndo_open to interfere there and reset those values.
So in fact the write from ocelot_port_enable can better be moved to
ocelot_init_port, and the .ndo_open hook deleted.
ocelot_port_disable touches DEV_MAC_ENA_CFG and QSYS_SWITCH_PORT_MODE_PORT_ENA,
in an attempt to undo what ocelot_adjust_link did. But since .ndo_stop
does not get called each time the link falls (i.e. this isn't a
substitute for .phylink_mac_link_down), felix already does better at
this by writing those registers already in felix_phylink_mac_link_down.
So keep ocelot_port_disable (for now, until ocelot is converted to
phylink too), and just delete the felix call to it, which is not
necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the obsolete and ambiguos macro in_irq() with new
macro in_hardirq().
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the development of the blamed patch, the "bool broadcast"
argument of dsa_port_tag_8021q_vlan_{add,del} was originally called
"bool local", and the meaning was the exact opposite.
Due to a rookie mistake where the patch was modified at the last minute
without retesting, the instances of dsa_port_tag_8021q_vlan_{add,del}
are called with the wrong values. During setup and teardown, cross-chip
notifiers should not be broadcast to all DSA trees, while during
bridging, they should.
Fixes: 724395f4dc ("net: dsa: tag_8021q: don't broadcast during setup/teardown")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
edumazet@google.com pointed out that queue_oob
does not check socket state after acquiring
the lock. He also pointed to an incorrect usage
of kfree_skb and an unnecessary setting of skb
length. This patch addresses those issue.
Signed-off-by: Rao Shoaib <Rao.Shoaib@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The controller doesn't seem to pick-up on clock changes, so set the
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN flag to query the clock frequency
directly from the clock.
Fixes: f84e411c85 ("mmc: sdhci-iproc: Add support for emmc2 of the BCM2711")
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1628334401-6577-6-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During the swap dependency on PCH_GBE to selection PTP_1588_CLOCK_PCH
incidentally dropped the implicit dependency on the PCI. Restore it.
Fixes: 18d359ceb0 ("pch_gbe, ptp_pch: Fix the dependency direction between these drivers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a known bug on BCM2711's SDHCI core integration where the
controller will hang when the difference between the core clock and the
bus clock is too great. Specifically this can be reproduced under the
following conditions:
- No SD card plugged in, polling thread is running, probing cards at
100 kHz.
- BCM2711's core clock configured at 500MHz or more.
So set 200 kHz as the minimum clock frequency available for that board.
For more information on the issue see this:
https://lore.kernel.org/linux-mmc/20210322185816.27582-1-nsaenz@kernel.org/T/#m11f2783a09b581da6b8a15f302625b43a6ecdeca
Fixes: f84e411c85 ("mmc: sdhci-iproc: Add support for emmc2 of the BCM2711")
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1628334401-6577-5-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Syzbot reported slab-out-of bounds write in decode_data().
The problem was in missing validation checks.
Syzbot's reproducer generated malicious input, which caused
decode_data() to be called a lot in sixpack_decode(). Since
rx_count_cooked is only 400 bytes and noone reported before,
that 400 bytes is not enough, let's just check if input is malicious
and complain about buffer overrun.
Fail log:
==================================================================
BUG: KASAN: slab-out-of-bounds in drivers/net/hamradio/6pack.c:843
Write of size 1 at addr ffff888087c5544e by task kworker/u4:0/7
CPU: 0 PID: 7 Comm: kworker/u4:0 Not tainted 5.6.0-rc3-syzkaller #0
...
Workqueue: events_unbound flush_to_ldisc
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374
__kasan_report.cold+0x1b/0x32 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:641
__asan_report_store1_noabort+0x17/0x20 mm/kasan/generic_report.c:137
decode_data.part.0+0x23b/0x270 drivers/net/hamradio/6pack.c:843
decode_data drivers/net/hamradio/6pack.c:965 [inline]
sixpack_decode drivers/net/hamradio/6pack.c:968 [inline]
Reported-and-tested-by: syzbot+fc8cd9a673d4577fb2e4@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Wake-on-PHY feature support by enabling the Link Up Event.
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SGMII/2500BaseX supports Pause frame as defined in the IEEE802.3x
Flow Control standardization.
Add this as a supported feature under the xpcs_sgmii_features struct.
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
samples: pktgen: enhance the usability of pktgen samples
This patchset improves the usability of pktgen samples by adding an option for
propagating the environment variable of normal user to sudo. And also adds the
missing IPv6 option to pktgen scripts.
Currently, all pktgen samples are able to use the environment variable instead
of optional parameters. However, it doesn't work appropriately when running
samples as normal user.
This is results of running sample as root and user:
// running as root
# DEV=eth0 DEST_IP=10.1.0.1 DST_MAC=00:11:22:33:44:55 ./pktgen_sample01_simple.sh -v -n 1
Running... ctrl^C to stop
// running as normal user
$ DEV=eth0 DEST_IP=10.1.0.1 DST_MAC=00:11:22:33:44:55 ./pktgen_sample01_simple.sh -v -n 1
[...]
ERROR: Please specify output device
The reason why passing the environment varaible doesn't work properly when
running samples as normal user is that the environment variable of normal user
doesn't propagate to sudo (root_check_run_with_sudo)). So the first commit
solves this issue by using "-E" (--preserve-env) option of "sudo", which passes
normal user's existing environment variables.
Also, "sample04" and "sample05" are not working properly when running with IPv6
option parameter("-6"). Because the commit 0f06a6787e ("samples: Add an IPv6
"-6" option to the pktgen scripts") has omitted the addition of this option at
these samples. So the second commit adds missing IPv6 option to pktgen scripts.
====================
Fixes: 0f06a6787e ("samples: Add an IPv6 "-6" option to the pktgen scripts")
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, "sample04" and "sample05" are not working properly when
running with an IPv6 option("-6"). The commit 0f06a6787e ("samples:
Add an IPv6 "-6" option to the pktgen scripts") has omitted the addition
of this option at "sample04" and "sample05".
In order to support IPv6 option, this commit adds logic related to IPv6
option.
Fixes: 0f06a6787e ("samples: Add an IPv6 "-6" option to the pktgen scripts")
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All pktgen samples can use the environment variable instead of option
parameters(eg. $DEV is able to use instead of '-i' option).
This is results of running sample as root and user:
// running as root
# DEV=eth0 DEST_IP=10.1.0.1 DST_MAC=00:11:22:33:44:55 ./pktgen_sample01_simple.sh -v -n 1
Running... ctrl^C to stop
// running as normal user
$ DEV=eth0 DEST_IP=10.1.0.1 DST_MAC=00:11:22:33:44:55 ./pktgen_sample01_simple.sh -v -n 1
[...]
ERROR: Please specify output device
This results show the sample doesn't work properly when the sample runs
as normal user. Because the sample is restarted by the function
(root_check_run_with_sudo) to run with sudo. In this process, the
environment variable of normal user doesn't propagate to sudo.
It can be solved by using "-E"(--preserve-env) option of "sudo", which
preserve normal user's existing environment variables. So this commit
adds "-E" option in the function (root_check_run_with_sudo).
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Luo Jie says:
====================
net: mdio: Add IPQ MDIO reset related function
This patch series add the MDIO reset features, which includes
configuring MDIO clock source frequency and indicating CMN_PLL that
ethernet LDO has been ready, this ethernet LDO is dedicated in the
IPQ5018 platform.
Specify more chipset IPQ40xx, IPQ807x, IPQ60xx and IPQ50xx supported by
this MDIO driver.
Changes in v3:
* simplify the function ipq_mdio_reset.
Changes in v2:
* Addressed review comments (Andrew Lunn).
* Remove the IS_ERR().
* make binding patch part of series.
* document the property 'reg' and 'clock'.
Changes in v1:
* make MDIO_IPQ4019 unchanged for backwards compatibility.
* remove the PHY reset functions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The new added properties resource "reg" is for configuring
ethernet LDO in the IPQ5018 chipset, the property "clocks"
is for configuring the MDIO clock source frequency.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPQ MDIO driver currently supports the chipset IPQ40xx, IPQ807x,
IPQ60xx and IPQ50xx.
Add the compatible 'qcom,ipq5018-mdio' because of ethernet LDO dedicated
to the IPQ5018 platform.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
