On MSM8996, the default bootloader configuration leaves the hosts in some
weird state that never allows them to function properly under Linux.
Add the hardware resets so that we can start clean and get them actually
working.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162642.608106-1-konrad.dybcio@somainline.org
It looks like all Tone devices out in the wild are using PMI8996, which
suggests the PMI8994-variant DTs are not needed. Remove them.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162525.607946-1-konrad.dybcio@somainline.org
Tone does not have a functioning bootloader framebuffer and Linux allocates
the DRM framebuffer dynamically. Free up 36 MiB of precious RAM by removing
this reservation.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162319.607629-1-konrad.dybcio@somainline.org
Merge the two DT files into one, sort the nodes and fix up a couple of style
incoherencies by adding some newlines, removing some, sorting properties etc.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-14-konrad.dybcio@somainline.org
While the Pro-1 is based on MTP and is very close to it, it's really not great
for it to include the MTP dtsi straight up, as any small change will affect
both boards and not all of them will apply to the phone as well.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-13-konrad.dybcio@somainline.org
MMCC is a component of the SoC that should always be configured. It was kept
off due to misconfiguration on clamshell machines. Keep it disabled on these
ones and enable it by default on all the others.
Exactly the same story applies to MMSS_SMMU, which directly depends on MMCC.
Do note, that if a platform doesn't use neither EFIFB (only applies to WoA
devices in this case) or simplefb (applies to precisely 2 msm8998 devices
as of this commit), this will not cause any harm.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-10-konrad.dybcio@somainline.org
While not strictly necessary, at least on maple, configure the USB extcon,
which requires two pins on Yoshino.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-5-konrad.dybcio@somainline.org
Remove the unnecessary level of indentation, commonize SDC2 pins and notice
that SDCC2_CD_ON and _OFF is identical, deduplicate it!
Also, remove some unnecessary overrides and use decimal values in #-cells
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-1-konrad.dybcio@somainline.org
The dts entry vdda-supply connects to a common vdda-phy-supply rail. Rename
to reflect what the functionality is.
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220111125212.2343184-4-bryan.odonoghue@linaro.org
There's no reason the timer needs > 32-bits of address or size.
Since we using 32-bit size, we need to define ranges properly.
Fixes warnings as:
```
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: timer@17c90000: #size-cells:0:0: 1 was expected
From schema: Documentation/devicetree/bindings/timer/arm,arch_timer_mmio.yaml
```
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220626105800.35586-1-david@ixit.cz
DT schema expects names of operating points tables to start with
"opp-table":
ipq6018-cp01-c1.dtb: cpu_opp_table: $nodename:0: 'cpu_opp_table' does not match '^opp-table(-[a-z0-9]+)?$'
Use hyphens instead of underscores, fix the names to match DT schema or
remove the prefix entirely when it is not needed.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220627093250.84391-1-krzysztof.kozlowski@linaro.org
"make dtbs_check" complains about the missing "-supply" suffix for
vdd_lvs1_2 which is clearly a typo, originally introduced in the
msm8994-smd-rpm.dtsi file and apparently later copied to
msm8992-xiaomi-libra.dts:
msm8992-lg-bullhead-rev-10/101.dtb: pm8994-regulators: 'vdd_lvs1_2'
does not match any of the regexes:
'.*-supply$', '^((s|l|lvs|5vs)[0-9]*)|(boost-bypass)|(bob)$', 'pinctrl-[0-9]+'
From schema: regulator/qcom,smd-rpm-regulator.yaml
msm8992-xiaomi-libra.dtb: pm8994-regulators: 'vdd_lvs1_2'
does not match any of the regexes:
'.*-supply$', '^((s|l|lvs|5vs)[0-9]*)|(boost-bypass)|(bob)$', 'pinctrl-[0-9]+'
From schema: regulator/qcom,smd-rpm-regulator.yaml
Reported-by: Rob Herring <robh@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@somainline.org>
Fixes: f3b2c99e73 ("arm64: dts: Enable onboard SDHCI on msm8992")
Fixes: 0f5cdb31e8 ("arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220627135938.2901871-1-stephan.gerhold@kernkonzept.com
The commit e8aa7b17fe broke the 32-bit load-word unalignment exception
handler because it calculated the wrong amount of bits by which the value
should be shifted. This patch fixes it.
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: e8aa7b17fe ("parisc/unaligned: Rewrite inline assembly of emulate_ldw()")
Cc: stable@vger.kernel.org # v5.18
Fixes all over the place, most notably we are disabling
IRQ hardening (again!).
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmK5naIPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpwPYIAJpkb2XCs/NzPHFhO6LbjGH0CsRWQJm/T2NP
cG0MQFFK3kIRUlRQXMDOE+Rv40QOnr0WqwlyeVYApmiYCbHvl0Nu/IIzzjwEL6w8
Yq9fWJ+l8SMYrOJ5IVl/SDr2U8HP9qZZGj/OokEVA7fZX6whWZJ8+540ua4CAOM3
mb5+ujaa2pjIR1AJG3yW4hOMtLD+c382efFZu7noewJ1+TCORCOPxyBc1/yFRxvZ
qmeGTqDx93kzNI2UEf+hroQSlpQEZJRktS35CGFBplZ93UxPSeNcq6M4jtPv8ZHc
AX+5mHkOvuw5gZbECzSRHo2y/MfJ28KrFLysxvfw/mM0Rcshj1E=
=6wpG
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"Fixes all over the place, most notably we are disabling
IRQ hardening (again!)"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_ring: make vring_create_virtqueue_split prettier
vhost-vdpa: call vhost_vdpa_cleanup during the release
virtio_mmio: Restore guest page size on resume
virtio_mmio: Add missing PM calls to freeze/restore
caif_virtio: fix race between virtio_device_ready() and ndo_open()
virtio-net: fix race between ndo_open() and virtio_device_ready()
virtio: disable notification hardening by default
virtio: Remove unnecessary variable assignments
virtio_ring : keep used_wrap_counter in vq->last_used_idx
vduse: Tie vduse mgmtdev and its device
vdpa/mlx5: Initialize CVQ vringh only once
vdpa/mlx5: Update Control VQ callback information
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
modpost used to detect it, but it had been broken for a decade.
Commit 28438794ab ("modpost: fix section mismatch check for exported
init/exit sections") fixed it so modpost started to warn it again, then
this showed up:
MODPOST vmlinux.symvers
WARNING: modpost: vmlinux.o(___ksymtab_gpl+tick_nohz_full_setup+0x0): Section mismatch in reference from the variable __ksymtab_tick_nohz_full_setup to the function .init.text:tick_nohz_full_setup()
The symbol tick_nohz_full_setup is exported and annotated __init
Fix this by removing the __init annotation of tick_nohz_full_setup or drop the export.
Drop the export because tick_nohz_full_setup() is only called from the
built-in code in kernel/sched/isolation.c.
Fixes: ae9e557b5b ("time: Export tick start/stop functions for rcutorture")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A new compatible string was introduced specifically for BCM2711, so make
use of it.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
bcm2835-pm's bindings now support explicitly setting 'reg-names,' so use
them.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a new compatible string for BCM2711 and the option to provide a
third reg property for the board's new RPiVid ASB.
In BCM2711 the new RPiVid ASB took over V3D, which is our only consumer
of this driver so far. The old ASB is still be present with ISP and H264
bits but no V3D.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Anticipating the introduction of BCM2711, of which we'll need to support
its new RPiVid ASB, introduce reg-names into bcm2835-pm's binding. This
will help to have a consistent mapping between resources and their
meaning.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This converts the brcm,bcm2835-pm bindings from text to proper schema.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
When br_netfilter module is loaded, skbs may be diverted to the
ipv4/ipv6 hooks, just like as if we were routing.
Unfortunately, bridge filter hooks with priority 0 may be skipped
in this case.
Example:
1. an nftables bridge ruleset is loaded, with a prerouting
hook that has priority 0.
2. interface is added to the bridge.
3. no tcp packet is ever seen by the bridge prerouting hook.
4. flush the ruleset
5. load the bridge ruleset again.
6. tcp packets are processed as expected.
After 1) the only registered hook is the bridge prerouting hook, but its
not called yet because the bridge hasn't been brought up yet.
After 2), hook order is:
0 br_nf_pre_routing // br_netfilter internal hook
0 chain bridge f prerouting // nftables bridge ruleset
The packet is diverted to br_nf_pre_routing.
If call-iptables is off, the nftables bridge ruleset is called as expected.
But if its enabled, br_nf_hook_thresh() will skip it because it assumes
that all 0-priority hooks had been called previously in bridge context.
To avoid this, check for the br_nf_pre_routing hook itself, we need to
resume directly after it, even if this hook has a priority of 0.
Unfortunately, this still results in different packet flow.
With this fix, the eval order after in 3) is:
1. br_nf_pre_routing
2. ip(6)tables (if enabled)
3. nftables bridge
but after 5 its the much saner:
1. nftables bridge
2. br_nf_pre_routing
3. ip(6)tables (if enabled)
Unfortunately I don't see a solution here:
It would be possible to move br_nf_pre_routing to a higher priority
so that it will be called later in the pipeline, but this also impacts
ebtables evaluation order, and would still result in this very ordering
problem for all nftables-bridge hooks with the same priority as the
br_nf_pre_routing one.
Searching back through the git history I don't think this has
ever behaved in any other way, hence, no fixes-tag.
Reported-by: Radim Hrazdil <rhrazdil@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When verdict is NF_STOLEN, the skb might have been freed.
When tracing is enabled, this can result in a use-after-free:
1. access to skb->nf_trace
2. access to skb->mark
3. computation of trace id
4. dump of packet payload
To avoid 1, keep a cached copy of skb->nf_trace in the
trace state struct.
Refresh this copy whenever verdict is != STOLEN.
Avoid 2 by skipping skb->mark access if verdict is STOLEN.
3 is avoided by precomputing the trace id.
Only dump the packet when verdict is not "STOLEN".
Reported-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch fixes a race condition.
nft_rhash_update() might fail for two reasons:
- Element already exists in the hashtable.
- Another packet won race to insert an entry in the hashtable.
In both cases, new() has already bumped the counter via atomic_add_unless(),
therefore, decrement the set element counter.
Fixes: 22fe54d5fe ("netfilter: nf_tables: add support for dynamic set updates")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Replace the deprecated ida_simple_{get,remove} with ida_{alloc,free}.
Link: https://lore.kernel.org/r/20220616055052.4559-1-liubo03@inspur.com
Signed-off-by: Bo Liu <liubo03@inspur.com>
[sudeep.holla: Replace ida_alloc_min with ida_alloc as suggested by Cristian]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
For imported dma-buf objects we leave the object as cache_coherent = 0
across all platforms, which is reasonable given that have no clue what
the memory underneath is, and its not like the driver can ever manually
clflush the pages anyway (like with i915_gem_clflush_object) for such
objects. However on discrete we choose to treat cache_dirty = true as a
programmer error, leading to a warning. The simplest fix looks to be to
just change the ordering in cpu_write_needs_clflush to prevent ever
setting cache_dirty for dma-buf objects on discrete.
Fixes: d028a7690d ("drm/i915/dmabuf: Fix prime_mmap to work when using LMEM")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5266
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622155919.355081-1-matthew.auld@intel.com
(cherry picked from commit 563aaf4a92)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently i915 disables d3cold for i915 pci dev.
This blocks D3 for i915 gfx pci upstream bridge (VSP).
Let's disable d3cold at gfx root port to make sure that
i915 gfx VSP can transition to D3 to save some power.
We don't need to disable/enable d3cold in rpm, s2idle
suspend/resume handlers. Disabling/Enabling d3cold at
gfx root port in probe/remove phase is sufficient.
Fixes: 1a085e2341 ("drm/i915: Disable D3Cold in s2idle and runtime pm")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Badal Nilawar <badal.nilawar@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220616122249.5007-1-anshuman.gupta@intel.com
(cherry picked from commit 138c2fca6f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
commit 555dbf1a9a ("nfsd: Replace use of rwsem with errseq_t")
incidentally broke translation of -EINVAL to nfserr_notsupp.
The patch restores that.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 555dbf1a9a ("nfsd: Replace use of rwsem with errseq_t")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
The recent change to split reads into chunks has several problems:
1. If an SPI controller has no transfer size limit, max_chunk is
SIZE_MAX, and num_msgs becomes zero, causing no data to be read
into the buffer, and exposing the original contents of the buffer
to userspace,
2. If the requested read size is not a multiple of the maximum
transfer size, the last transfer reads too much data, overflowing
the buffer,
3. The loop logic differs from the write case.
Fix the above by:
1. Keeping track of the number of bytes that are still to be
transferred, instead of precalculating the number of messages and
keeping track of the number of bytes tranfered,
2. Calculating the transfer size of each individual message, taking
into account the number of bytes left,
3. Switching from a "while"-loop to a "do-while"-loop, and renaming
"msg_count" to "segment".
While at it, drop the superfluous cast from "unsigned int" to "unsigned
int", also from at25_ee_write(), where it was probably copied from.
Fixes: 0a35780c75 ("eeprom: at25: Split reads into chunks and cap write size")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7ae260778d2c08986348ea48ce02ef148100e088.1655817534.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
INVALID_VFS{U,G}ID represent ids which have no mapping in the target
mnt_usersns. This can happen for a couple of different reasons -- the
source id might be valid but has no mapping in mnt_userns, or the source
id might have been invalid (either due to a failed mapping or because it
was set to invalid to indicate it is uninitialized).
This means that two arbitrary vfs{u,g}ids which are both invalid could
represent two different underlying ids, or they could represent a failed
mapping and an uninitialized value. In these situation the vfs{u,g}id
equality functions evaluate these ids as equal, and care must be taken
when comparing ids to avoid problems. It would be less error prone to
always evaluate two invalid ids as not equal to each other, and to check
explicitly for vfs{u,g}id validity when that is needed.
Change all vfs{u,g}id equality functions to return false when both ids
are invalid. Functions for checking whether an id is valid exist and are
already being used by code which needs to check this.
Link: https://lore.kernel.org/linux-fsdevel/YrIMZirGoE0VIO45@do-x1extreme
Signed-off-by: Seth Forshee <sforshee@digitalocean.com>
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
When building kernel documentation new warnings were generated because
the name in the parameter documentation didn't match the parameter name.
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
The actual driver will be added via the CAN tree.
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Max Staudt <max@enpas.org>
Link: https://lore.kernel.org/r/20220618180134.9890-1-max@enpas.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 30f8c74ca9 ("drm/vc4: Warn if some v3d code is run on BCM2711")
introduced a check in vc4_perfmon_get() that dereferences a pointer before
we checked whether that pointer is valid or not.
Let's rework that function a bit to do things in the proper order.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 30f8c74ca9 ("drm/vc4: Warn if some v3d code is run on BCM2711")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622080243.22119-1-maxime@cerno.tech
Commit e8ffbb71f7 ("serial: 8250: use THRE & __stop_tx also with
DMA") changed __dma_tx_complete() to enable THRI that is cleared in
__stop_tx() once THRE is asserted as UART runs out bits to transmit. It
is possible, however, that more data arrives in between in which case
serial8250_tx_dma() resumes Tx. THRI is not supposed to be on during
DMA Tx because DMA is based on completion handler, therefore THRI must
be cleared unconditionally in serial8250_tx_dma().
When Tx is about to start, another race window exists with
serial8250_handle_irq() leading to a call into __stop_tx() while the
Tx has already been resumed:
__tx_complete():
-> spin_lock(port->lock)
-> dma->tx_running = 0
-> serial8250_set_THRI()
-> spin_unlock(port->lock)
uart_start():
serial8250_handle_irq():
-> spin_lock(port->lock)
-> serial8250_tx_dma():
-> dma->tx_running = 1
-> spin_unlock(port->lock)
-> spin_lock(port->lock)
-> __stop_tx()
Close this race by checking !dma->tx_running before calling into
__stop_tx().
Fixes: e8ffbb71f7 ("serial: 8250: use THRE & __stop_tx also with DMA")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220615090651.15340-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver must provide throttle and unthrottle in uart_ops when it
sets UPSTAT_AUTORTS. Add them using existing stop_rx &
enable_interrupts functions.
Fixes: 2a76fa2830 (serial: pl011: Adopt generic flag to store auto RTS status)
Cc: stable <stable@kernel.org>
Cc: Lukas Wunner <lukas@wunner.de>
Reported-by: Nuno Gonçalves <nunojpg@gmail.com>
Tested-by: Nuno Gonçalves <nunojpg@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220614075637.8558-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The src_maxburst and dst_maxburst have been changed to 1 but the settings
of the UCON register aren't changed yet. They should be changed as well
according to the dmaengine slave config.
Fixes: aa2f80e752 ("serial: samsung: fix maxburst parameter for DMA transactions")
Cc: stable <stable@kernel.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220627065113.139520-1-chanho61.park@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ffd381445e ("serial: 8250: dw: Move the USR register to pdata")
caused NULL-pointer dereference when booting with ACPI by unconditional
usage of the recently added pdata.
In order to fix that and prevent similar issues in future, hook the
default version of this structure in dw8250_acpi_match table.
While at it, sort all entries alphabetically.
Fixes: ffd381445e ("serial: 8250: dw: Move the USR register to pdata")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20220620121046.1307412-1-mw@semihalf.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
