Add basic support in dpaa2-eth for devlink. For the moment, just
register the device with devlink, add the corresponding devlink port and
implement the .info_get() callback.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new devlink callback, .trap_group_action_set(), which can be used
by device drivers which do not support controlling the action (drop,
trap) on each trap but rather on the entire group trap.
If this new callback is populated, it will take precedence over the
.trap_action_set() callback when the user requests a change of all the
traps in a group.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add parser error drop packet traps, so that capable device driver could
register them with devlink. The new packet trap group holds any drops of
packets which were marked by the device as erroneous during header
parsing. Add documentation for every added packet trap and packet trap
group.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson says:
====================
ionic error recovery
This set of patches comes mostly from error recovery path testing,
as well as a couple of upstream review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the new firmware image downladed for update is corrupted
or is a bad format, the download process will report a status
code specifically for that.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the lif's ident information for the uc and mc filter
counts rather than the ionic's version, to be sure
we're getting the info that is specific to this lif.
While we're thinking about it, add some missing error
checking where we get the lif's identity information.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
After we do a fw upgrade and refill the ionic->ident.dev, we
also need to update the other identity info. Since the lif
identity needs to be updated each time the ionic identity is
refreshed, we can pull it into ionic_identify().
The debugfs entry is moved so that it doesn't cause an
error message when the data is refreshed after the fw upgrade.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some time ago we short-circuited the queue disables on a timeout
error in order to not have to wait on every queue when we already
know it will time out. However, this meant that we're not
properly stopping all the interrupts and napi contexts. This
changes queue disable to always call ionic_qcq_disable() and to
give it an argument to know when to not do the adminq request.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a couple of error recovery paths that can come through
ionic_qcq_disable() without having set up the qcq, so we need
to make sure we have a valid qcq pointer before using it.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear our link check requested flag on an allocation error.
We end up dropping this link check request, but that should
be fine as our watchdog will come back a few seconds later
and request it again.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check through our work list for additional items. This normally
will only have one item, but occasionally may have another
job waiting. There really is no need reschedule ourself here.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The event notification queue is set up a little differently in the
NIC and so the notifyq q and cq descriptor structures need to be
contiguous, which got missed in an earlier patch that separated
out the q and cq descriptor allocations. That patch was aimed at
making the big tx and rx descriptor queue allocations easier to
manage - the notifyq is much smaller and doesn't need to be split.
This patch simply adds an if/else and slightly different code for
the notifyq descriptor allocation.
Fixes: ea5a8b09dc ("ionic: reduce contiguous memory allocation requirement")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
===================
s390/net: updates 2020-10-01
Patches 1-3 enable qeth to also support the .set_channels() ethtool
callback for OSA devices. This completes support for the full range
of device types.
The other patches are just the usual mix of cleanups.
(Even one for ctcm!)
===================
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/s390/net/ctcm_fsms.h: fsm_action_nop - only declaration left
after commit 04885948b1 ("ctc: removal of the old ctc driver")
drivers/s390/net/ctcm_mpc.h: ctcmpc_open - only declaration left after
commit 293d984f0e ("ctcm: infrastructure for replaced ctc driver")
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add/delete some blanks, white spaces and braces.
- Fix misindentations.
- Adjust a deprecated header include, and htons() conversion.
- Remove extra 'return' statements.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace our custom version of netdev_name().
Once we started to allocate the netdev at probe time with
commit d3d1b205e8 ("s390/qeth: allocate netdevice early"), this
stopped working as intended anyway.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The discipline struct is a fixed group of function pointers.
So declare the L2 and L3 disciplines as constant.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For OSA devices that are _not_ configured in prio-queue mode, give users
the option of selecting the number of active TX queues.
This requires setting up the HW queues with a reasonable default QoS
value in the QIB's PQUE parm area.
As with the other device types, we bring up the device with a minimal
number of TX queues for compatibility reasons.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a proper struct, and only program the QIB extensions for devices
where they are supported.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When re-initializing a device, we can hit a situation where
qeth_osa_set_output_queues() detects that it supports more or less
HW TX queues than before. Right now we adjust dev->real_num_tx_queues
from right there, but
1. it's getting more & more complicated to cover all cases, and
2. we can't re-enable the actually expected number of TX queues later
because we lost the needed information.
So keep track of the wanted TX queues (on initial setup, and whenever
its changed via .set_channels), and later use that information when
re-enabling the netdevice.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl93ap4ACgkQSD+KveBX
+j5+eAf/dvxx+WyWr5pV3gxd0x7K/wV+F1JFVe99k8yH6kYbpo56U+oRQGP4kvnG
4Ggb/XE7hSahvReRVD5vn4LKk2RQ/GMWEurF/GQDPklaHZyZHtcI3+2C/azEHnf+
vGgbM1xDT0gNZoa+2pA7LBgruJF/k+gRbth6EHrjlcxqiqt2k4d5Hs0m/Xd5R0TC
D+Yks3uHAOrTiP2idOWNoWmd5AOmh802wX0w4iyKZ9ZfJGMN3t2AKyZDIhNfPyPf
avebIihkr5y5DsYGZE+HjZjK0+vXaKVAGgzDbeLZ2sPVdCJJAFRZptG6mPJ0d0N3
TPwcBZcs5BsJkEQ5XqBA0IwJjksVeA==
=421I
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
From: Saeed Mahameed <saeedm@nvidia.com>
====================
This series introduces some fixes to mlx5 driver.
v1->v2:
- Patch #1 Don't return while mutex is held. (Dave)
v2->v3:
- Drop patch #1, will consider a better approach (Jakub)
- use cpu_relax() instead of cond_resched() (Jakub)
- while(i--) to reveres a loop (Jakub)
- Drop old mellanox email sign-off and change the committer email
(Jakub)
Please pull and let me know if there is any problem.
For -stable v4.15
('net/mlx5e: Fix VLAN cleanup flow')
('net/mlx5e: Fix VLAN create flow')
For -stable v4.16
('net/mlx5: Fix request_irqs error flow')
For -stable v5.4
('net/mlx5e: Add resiliency in Striding RQ mode for packets larger than MTU')
('net/mlx5: Avoid possible free of command entry while timeout comp handler')
For -stable v5.7
('net/mlx5e: Fix return status when setting unsupported FEC mode')
For -stable v5.8
('net/mlx5e: Fix race condition on nhe->n pointer in neigh update')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For older versions of gcc, the array = {0}; will cause warnings:
drivers/scsi/ufs/ufshcd-crypto.c: In function 'ufshcd_crypto_keyslot_program':
drivers/scsi/ufs/ufshcd-crypto.c:62:8: warning: missing braces around initializer [-Wmissing-braces]
union ufs_crypto_cfg_entry cfg = { 0 };
^
drivers/scsi/ufs/ufshcd-crypto.c:62:8: warning: (near initialization for 'cfg.reg_val') [-Wmissing-braces]
drivers/scsi/ufs/ufshcd-crypto.c: In function 'ufshcd_clear_keyslot':
drivers/scsi/ufs/ufshcd-crypto.c:103:8: warning: missing braces around initializer [-Wmissing-braces]
union ufs_crypto_cfg_entry cfg = { 0 };
^
2 warnings generated
Link: https://lore.kernel.org/r/20201002063538.1250-1-shipujin.t@gmail.com
Fixes: 70297a8ac7 ("scsi: ufs: UFS crypto API")
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Pujin Shi <shipujin.t@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following warning:
[drivers/scsi/qla2xxx/qla_dbg.c:2451]: (warning) %ld in format string (no. 4)
requires 'long' but the argument type is 'unsigned long'.
Link: https://lore.kernel.org/r/20200930022515.2862532-4-yebin10@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following warnings:
[drivers/scsi/qla2xxx/qla_os.c:4882]: (warning) %ld in format string (no. 2)
requires 'long' but the argument type is 'unsigned long'.
[drivers/scsi/qla2xxx/qla_os.c:5011]: (warning) %ld in format string (no. 1)
requires 'long' but the argument type is 'unsigned long'.
Link: https://lore.kernel.org/r/20200930022515.2862532-3-yebin10@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following warnings:
[drivers/scsi/qla2xxx/tcm_qla2xxx.c:884]: (warning) %u in format string (no. 1)
requires 'unsigned int' but the argument type is 'signed int'.
[drivers/scsi/qla2xxx/tcm_qla2xxx.c:885]: (warning) %u in format string (no. 1)
requires 'unsigned int' but the argument type is 'signed int'.
[drivers/scsi/qla2xxx/tcm_qla2xxx.c:886]: (warning) %u in format string (no. 1)
requires 'unsigned int' but the argument type is 'signed int'.
[drivers/scsi/qla2xxx/tcm_qla2xxx.c:887]: (warning) %u in format string (no. 1)
requires 'unsigned int' but the argument type is 'signed int'.
[drivers/scsi/qla2xxx/tcm_qla2xxx.c:888]: (warning) %u in format string (no. 1)
requires 'unsigned int' but the argument type is 'signed int'.
Link: https://lore.kernel.org/r/20200930022515.2862532-2-yebin10@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some iSCSI targets went with the traditional "export N ports" approach and
then allowed the initiator to multipath over them. Other targets went the
opposite direction and export a single port, and then software on the
target side performs load balancing and failover to other targets via an
iSCSI specific feature or IP takover.
The problem for the 2nd type of config is we quickly run out of our five
retries and get I/O errors. In these setups we want to reduce resource use
on the initiator side so we only wanted the one session and no
dm-multipath. To handle traditional multipath operations like failover we
do IP takover on the target side. So we would have an iSCSI target running
on node1. Some monitoring software decides it's dead or the node is
overloaded so it starts the iSCSI target on node2. The problem is for the
failover case where we might have the equivalent of a dm-multipath
temporary all paths down, or we just have to try more than 5 nodes before
finding a good one.
To handle this type of issue allow the user to configure the disk cmd
retries from -1 to the current max of 5. -1 means infinite retries and
should be used for setups where some other setting is going to control when
to fail. For example iSCSI has the replacement/recovery timeout and fc
(some users have used FC with NPIV and done something similar as IP
takover) has dev_loss_tmo/fast_io_fail which will eventually expire and
fail I/O.
Link: https://lore.kernel.org/r/1601566554-26752-3-git-send-email-michael.christie@oracle.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add infinite retry support to SCSI midlayer by combining common checks for
retries into some helper functions, and then checking for the
-1/SCSI_CMD_RETRIES_NO_LIMIT.
Link: https://lore.kernel.org/r/1601566554-26752-2-git-send-email-michael.christie@oracle.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Third set of patches for v5.10. Lots of iwlwifi patches this time, but
also few patches ath11k and of course smaller changes to other
drivers.
Major changes:
rtw88
* properly recover from firmware crashes on 8822c
* dump firmware crash log
iwlwifi
* protected Target Wake Time (TWT) implementation
* support disabling 5.8GHz channels via ACPI
* support VHT extended NSS capability
* enable Target Wake Time (TWT) by default
ath11k
* improvements to QCA6390 PCI support to make it more usable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfdzOKAAoJEG4XJFUm622bAxEH/2XBLA6RJ0/ypDYt32qj7q5/
hgV3tQkaCXTKnXo0O/6DtihdLD1gARg3Y8s1BY4wHzIZ57iR2LxKumzDS9f6S2oq
6/7OmBubZVzK8oii2bTleOu524Dfq6B019uOgtQJMAOT5S5X5uk25PDIfVCksv5m
ZKSNZINFqC2K9cQkXKP0cD0SSJDDHvcMjI8/nZ91mNLJ7StO3En4WDNMQJ7Jfa3M
VX18GI6XB/pqb18+QJwTXUKN4jODTYHH8zJ6LvYfDFq9vhN2GomdK5f3W9teIUwY
omQavKAFCPAhBja61IVGyo47ZB3MH57ECyuuBtAPv/ydcwAGXlJToHO8avM4K7I=
=WApP
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
Third set of patches for v5.10. Lots of iwlwifi patches this time, but
also few patches ath11k and of course smaller changes to other
drivers.
Major changes:
rtw88
* properly recover from firmware crashes on 8822c
* dump firmware crash log
iwlwifi
* protected Target Wake Time (TWT) implementation
* support disabling 5.8GHz channels via ACPI
* support VHT extended NSS capability
* enable Target Wake Time (TWT) by default
ath11k
* improvements to QCA6390 PCI support to make it more usable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Offload tc-flower to mscc_ocelot switch using VCAP chains
The purpose of this patch is to add more comprehensive support for flow
offloading in the mscc_ocelot library and switch drivers.
The design (with chains) is the result of this discussion:
https://lkml.org/lkml/2020/6/2/203
I have tested it on Seville VSC9953 and Felix VSC9959, but it should
also work on Ocelot-1 VSC7514.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide an example script which can be used as a skeleton for offloading
TCAM rules in the Ocelot switches.
Not all actions are demoed, mostly because of difficulty to automate
this from a single board.
For example, policing. We can set up an iperf3 UDP server and client and
measure throughput at destination. But at least with DSA setups, network
namespacing the individual ports is not possible because all switch
ports are handled by the same DSA master. And we cannot assume that the
target platform (an embedded board) has 2 other non-switch generator
ports, we need to work with the generator ports as switch ports (this is
the reason why mausezahn is used, and not IP traffic like ping). When
somebody has an idea how to test policing, that can be added to this
test.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Via the OCELOT_MASK_MODE_REDIRECT flag put in the IS2 action vector, it
is possible to replace previous forwarding decisions with the port mask
installed in this rule.
I have studied Table 54 "MASK_MODE and PORT_MASK Combinations" from the
VSC7514 documentation and it appears to behave sanely when this rule is
installed in either lookup 0 or 1. Namely, a redirect in lookup 1 will
overwrite the forwarding decision taken by any entry in lookup 0.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue which led to the introduction of this check was that MAC_ETYPE
rules, such as filters on dst_mac and src_mac, would only match non-IP
frames. There is a knob in VCAP_S2_CFG which forces all IP frames to be
treated as non-IP, which is what we're currently doing if the user
requested a dst_mac filter, in order to maintain sanity.
But that knob is actually per IS2 lookup. And the good thing with
exposing the lookups to the user via tc chains is that we're now able to
offload MAC_ETYPE keys to one lookup, and IP keys to the other lookup.
So let's do that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were installing TCAM rules with the LOOKUP field as unmasked, meaning
that all entries were matching on all lookups. Now that lookups are
exposed as individual chains, let's make the LOOKUP explicit when
offloading TCAM entries.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VCAP ES0 is an egress VCAP operating on all outgoing frames.
This patch added ES0 driver to support vlan push action of tc filter.
Usage:
tc filter add dev swp1 egress protocol 802.1Q flower indev swp0 skip_sw \
vlan_id 1 vlan_prio 1 action vlan push id 2 priority 2
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VCAP IS1 is a VCAP module which can filter on the most common L2/L3/L4
Ethernet keys, and modify the results of the basic QoS classification
and VLAN classification based on those flow keys.
There are 3 VCAP IS1 lookups, mapped over chains 10000, 11000 and 12000.
Currently the driver is hardcoded to use IS1_ACTION_TYPE_NORMAL half
keys.
Note that the VLAN_MANGLE has been omitted for now. In hardware, the
VCAP_IS1_ACT_VID_REPLACE_ENA field replaces the classified VLAN
(metadata associated with the frame) and not the VLAN from the header
itself. There are currently some issues which need to be addressed when
operating in standalone, or in bridge with vlan_filtering=0 modes,
because in those cases the switch ports have VLAN awareness disabled,
and changing the classified VLAN to anything other than the pvid causes
the packets to be dropped. Another issue is that on egress, we expect
port tagging to push the classified VLAN, but port tagging is disabled
in the modes mentioned above, so although the classified VLAN is
replaced, it is not visible in the packet transmitted by the switch.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Ocelot switches, there are 2 ingress pipelines for flow offload
rules: VCAP IS1 (Ingress Classification) and IS2 (Security Enforcement).
IS1 and IS2 support different sets of actions. The pipeline order for a
packet on ingress is:
Basic classification -> VCAP IS1 -> VCAP IS2
Furthermore, IS1 is looked up 3 times, and IS2 is looked up twice (each
TCAM entry can be configured to match only on the first lookup, or only
on the second, or on both etc).
Because the TCAMs are completely independent in hardware, and because of
the fixed pipeline, we actually have very limited options when it comes
to offloading complex rules to them while still maintaining the same
semantics with the software data path.
This patch maps flow offload rules to ingress TCAMs according to a
predefined chain index number. There is going to be a script in
selftests that clarifies the usage model.
There is also an egress TCAM (VCAP ES0, the Egress Rewriter), which is
modeled on top of the default chain 0 of the egress qdisc, because it
doesn't have multiple lookups.
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Co-developed-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the mscc_ocelot_switch_lib is common between a pure switchdev and
a DSA driver, the procedure of retrieving a net_device for a certain
port index differs, as those are registered by their individual
front-ends.
Up to now that has been dealt with by always passing the port index to
the switch library, but now, we're going to need to work with net_device
pointers from the tc-flower offload, for things like indev, or mirred.
It is not desirable to refactor that, so let's make sure that the flower
offload core has the ability to translate between a net_device and a
port index properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this stage, the tc-flower offload of mscc_ocelot can only delegate
rules to the VCAP IS2 security enforcement block. These rules have, in
hardware, separate bits for policing and for overriding the destination
port mask and/or copying to the CPU. So it makes sense that we attempt
to expose some more of that low-level complexity instead of simply
choosing between a single type of action.
Something similar happens with the VCAP IS1 block, where the same action
can contain enable bits for VLAN classification and for QoS
classification at the same time.
So model the action structure after the hardware description, and let
the high-level ocelot_flower.c construct an action vector from multiple
tc actions.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trace-cmd report doesn't show events from target subsystem because
scsi_command_size() leaks through event format string:
[target:target_sequencer_start] function scsi_command_size not defined
[target:target_cmd_complete] function scsi_command_size not defined
Addition of scsi_command_size() to plugin_scsi.c in trace-cmd doesn't
help because an expression is used inside TP_printk(). trace-cmd event
parser doesn't understand minus sign inside [ ]:
Error: expected ']' but read '-'
Rather than duplicating kernel code in plugin_scsi.c, provide a dedicated
field for CONTROL byte.
Link: https://lore.kernel.org/r/20200929125957.83069-1-r.bolshakov@yadro.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a syn-cookies request socket don't pass MPTCP-level
validation done in syn_recv_sock(), we need to release
it immediately, or it will be leaked.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/89
Fixes: 9466a1cceb ("mptcp: enable JOIN requests even if cookies are in use")
Reported-and-tested-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* lots more S1G band support
* 6 GHz scanning, finally
* kernel-doc fixes
* non-split wiphy dump fixes in nl80211
* various other small cleanups/features
-----BEGIN PGP SIGNATURE-----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=B9Xl
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of changes, this time with:
* lots more S1G band support
* 6 GHz scanning, finally
* kernel-doc fixes
* non-split wiphy dump fixes in nl80211
* various other small cleanups/features
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Coly Li says:
====================
Introduce sendpage_ok() to detect misused sendpage in network related drivers
As Sagi Grimberg suggested, the original fix is refind to a more common
inline routine:
static inline bool sendpage_ok(struct page *page)
{
return (!PageSlab(page) && page_count(page) >= 1);
}
If sendpage_ok() returns true, the checking page can be handled by the
concrete zero-copy sendpage method in network layer.
The v10 series has 7 patches, fixes a WARN_ONCE() usage from v9 series,
- The 1st patch in this series introduces sendpage_ok() in header file
include/linux/net.h.
- The 2nd patch adds WARN_ONCE() for improper zero-copy send in
kernel_sendpage().
- The 3rd patch fixes the page checking issue in nvme-over-tcp driver.
- The 4th patch adds page_count check by using sendpage_ok() in
do_tcp_sendpages() as Eric Dumazet suggested.
- The 5th and 6th patches just replace existing open coded checks with
the inline sendpage_ok() routine.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In libceph, ceph_tcp_sendpage() does the following checks before handle
the page by network layer's zero copy sendpage method,
if (page_count(page) >= 1 && !PageSlab(page))
This check is exactly what sendpage_ok() does. This patch replace the
open coded checks by sendpage_ok() as a code cleanup.
Signed-off-by: Coly Li <colyli@suse.de>
Acked-by: Jeff Layton <jlayton@kernel.org>
Cc: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In iscsci driver, iscsi_tcp_segment_map() uses the following code to
check whether the page should or not be handled by sendpage:
if (!recv && page_count(sg_page(sg)) >= 1 && !PageSlab(sg_page(sg)))
The "page_count(sg_page(sg)) >= 1 && !PageSlab(sg_page(sg)" part is to
make sure the page can be sent to network layer's zero copy path. This
part is exactly what sendpage_ok() does.
This patch uses use sendpage_ok() in iscsi_tcp_segment_map() to replace
the original open coded checks.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Vasily Averin <vvs@virtuozzo.com>
Cc: Cong Wang <amwang@redhat.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Chris Leech <cleech@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In _drbd_send_page() a page is checked by following code before sending
it by kernel_sendpage(),
(page_count(page) < 1) || PageSlab(page)
If the check is true, this page won't be send by kernel_sendpage() and
handled by sock_no_sendpage().
This kind of check is exactly what macro sendpage_ok() does, which is
introduced into include/linux/net.h to solve a similar send page issue
in nvme-tcp code.
This patch uses macro sendpage_ok() to replace the open coded checks to
page type and refcount in _drbd_send_page(), as a code cleanup.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a10674bf24 ("tcp: detecting the misuse of .sendpage for Slab
objects") adds the checks for Slab pages, but the pages don't have
page_count are still missing from the check.
Network layer's sendpage method is not designed to send page_count 0
pages neither, therefore both PageSlab() and page_count() should be
both checked for the sending page. This is exactly what sendpage_ok()
does.
This patch uses sendpage_ok() in do_tcp_sendpages() to detect misused
.sendpage, to make the code more robust.
Fixes: a10674bf24 ("tcp: detecting the misuse of .sendpage for Slab objects")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Vasily Averin <vvs@virtuozzo.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently nvme_tcp_try_send_data() doesn't use kernel_sendpage() to
send slab pages. But for pages allocated by __get_free_pages() without
__GFP_COMP, which also have refcount as 0, they are still sent by
kernel_sendpage() to remote end, this is problematic.
The new introduced helper sendpage_ok() checks both PageSlab tag and
page_count counter, and returns true if the checking page is OK to be
sent by kernel_sendpage().
This patch fixes the page checking issue of nvme_tcp_try_send_data()
with sendpage_ok(). If sendpage_ok() returns true, send this page by
kernel_sendpage(), otherwise use sock_no_sendpage to handle this page.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Jan Kara <jack@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mikhail Skorzhinskii <mskorzhinskiy@solarflare.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Vlastimil Babka <vbabka@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
If a page sent into kernel_sendpage() is a slab page or it doesn't have
ref_count, this page is improper to send by the zero copy sendpage()
method. Otherwise such page might be unexpected released in network code
path and causes impredictable panic due to kernel memory management data
structure corruption.
This path adds a WARN_ON() on the sending page before sends it into the
concrete zero-copy sendpage() method, if the page is improper for the
zero-copy sendpage() method, a warning message can be observed before
the consequential unpredictable kernel panic.
This patch does not change existing kernel_sendpage() behavior for the
improper page zero-copy send, it just provides hint warning message for
following potential panic due the kernel memory heap corruption.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Cong Wang <amwang@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original problem was from nvme-over-tcp code, who mistakenly uses
kernel_sendpage() to send pages allocated by __get_free_pages() without
__GFP_COMP flag. Such pages don't have refcount (page_count is 0) on
tail pages, sending them by kernel_sendpage() may trigger a kernel panic
from a corrupted kernel heap, because these pages are incorrectly freed
in network stack as page_count 0 pages.
This patch introduces a helper sendpage_ok(), it returns true if the
checking page,
- is not slab page: PageSlab(page) is false.
- has page refcount: page_count(page) is not zero
All drivers who want to send page to remote end by kernel_sendpage()
may use this helper to check whether the page is OK. If the helper does
not return true, the driver should try other non sendpage method (e.g.
sock_no_sendpage()) to handle the page.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Jan Kara <jack@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mikhail Skorzhinskii <mskorzhinskiy@solarflare.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Vlastimil Babka <vbabka@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more generic eth_platform_get_mac_address() which can get a MAC
address from other than DT platform specific sources too. Check if the
obtained address is valid.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
