The recent changes to switch SoCs to boot with ti-sysc interconnect
target module driver and genpd caused few regressions:
- The omap_prm reset driver needs to clear any reset bits deasserted by
the bootloader or kexec boot for the three reset bit cases. Otherwise
we can have an oops with accelerators starting to boot with potentially
unconfigured MMU for example
- Custom kernel configs are not automatically selecting simple-pm-bus
driver that we now need to probe interconnects so we need to select it
always
- We are not passing legacy platform data in auxdata with simple-pm-bus
like we do for simple-bus. We need to pass auxdata to simple-pm-bus so
it can pass it to of_platform_populate()
Then recent RCU changes started causing splats for cpuidle44xx that now
need RCU_NONIDLE added to the calls in several places
And then we have few device specific fixes:
- We need to remove legacy spi-cs-hig for gta04 display to work, and
set the gpio to active low
- Omap1 specific ohci-omap needs to call gpio_free()
- Droid4 needs to use padconf interrupt for the slider as the edge
gpio interrupts may be lost for deeper idle states
-----BEGIN PGP SIGNATURE-----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=KgUu
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.11/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.11-rc cycle
The recent changes to switch SoCs to boot with ti-sysc interconnect
target module driver and genpd caused few regressions:
- The omap_prm reset driver needs to clear any reset bits deasserted by
the bootloader or kexec boot for the three reset bit cases. Otherwise
we can have an oops with accelerators starting to boot with potentially
unconfigured MMU for example
- Custom kernel configs are not automatically selecting simple-pm-bus
driver that we now need to probe interconnects so we need to select it
always
- We are not passing legacy platform data in auxdata with simple-pm-bus
like we do for simple-bus. We need to pass auxdata to simple-pm-bus so
it can pass it to of_platform_populate()
Then recent RCU changes started causing splats for cpuidle44xx that now
need RCU_NONIDLE added to the calls in several places
And then we have few device specific fixes:
- We need to remove legacy spi-cs-hig for gta04 display to work, and
set the gpio to active low
- Omap1 specific ohci-omap needs to call gpio_free()
- Droid4 needs to use padconf interrupt for the slider as the edge
gpio interrupts may be lost for deeper idle states
* tag 'omap-for-v5.11/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Fix lost keypad slide interrupts for droid4
drivers: bus: simple-pm-bus: Fix compatibility with simple-bus for auxdata
ARM: OMAP2+: Fix booting for am335x after moving to simple-pm-bus
ARM: OMAP2+: Fix suspcious RCU usage splats for omap_enter_idle_coupled
ARM: dts; gta04: SPI panel chip select is active low
soc: ti: omap-prm: Fix boot time errors for rst_map_012 bits 0 and 1
ARM: OMAP1: OSK: fix ohci-omap breakage
DTS: ARM: gta04: remove legacy spi-cs-high to make display work again
Link: https://lore.kernel.org/r/pull-1611818709-243493@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2a3e487a3e