linux-xiaomi-chiron/drivers
Harald Freudenberger 7c4e91c095 s390/zcrypt: new sysfs attributes serialnr and mkvps
This patch extends the sysfs interface with two new attributes for the
CEX4, CEX5 and CEX6 crypto cards/queues in coprocessor ('CCA') mode:
  /sys/devices/ap/cardxx/serialnr
  /sys/devices/ap/cardxx/xx.yyyy/mkvps

The serialnr attribute is card based and shows the 8 character ASCII
serial number string which should unique identify the card.

The mkvps is queue based and displays 3 lines of information about the
new, current and old master key register:
  AES NEW: <new_aes_mk_state> <new_aes_mk_mkvp>
  AES CUR: <cur_aes_mk_state> <cur_aes_mk_mkvp>
  AES OLD: <old_aes_mk_state> <old_aes_mk_mkvp>
with
  <new_aes_mk_state>: 'empty' or 'partial' or 'full'
  <cur_aes_mk_state>: 'valid' or 'invalid'
  <old_aes_mk_state>: 'valid' or 'invalid'
  <new_aes_mk_mkvp>, <cur_aes_mk_mkvp>, <old_aes_mk_mkvp>
    8 byte hex string with leading 0x
MKVP means Master Key Verification Pattern and is a folded hash over
the key value. Only the states 'full' and 'valid' result in displaying
a useful mkvp, otherwise a mkvp of all bytes zero is shown. If for any
reason the FQ fails and the (cached) information is not available, the
state '-' will be shown with the mkvp value also '-'. The values shown
here are the very same as the cca panel tools displays. As of now only
the AES master keys states and verification patterns are shown. A CCA
APQN also has similar master key registers for DES, RSA and ECC. So
the content of this attribute may get extended.

Reading the sysfs attribute automatically triggers an FQ CPRB to be
sent to the queue as long as the queue is (soft-) online. For the
serialnr attribute the queue with the default domain id is addressed
(if available and valid). This is reasonable as it is assumed that
this sysfs interface is not performance critical and on the other side
a master key change should be visiable as soon as possible. When a
queue is (soft-) offline however, the cached values are displayed. If
no cached values are available, the serial number string will be empty
and the mkvp lines will show state '-' and mkvp value '-'.

Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
2019-07-29 18:14:17 +02:00
..
accessibility
acpi libnvdimm fixes v5.3-rc2 2019-07-27 08:25:51 -07:00
amba
android
ata
atm
auxdisplay
base Char/Misc driver fixes for 5.3-rc2 2019-07-28 10:26:10 -07:00
bcma
block
bluetooth
bus
cdrom
char
clk
clocksource
connector
counter
cpufreq
cpuidle
crypto
dax
dca
devfreq
dio
dma
dma-buf
edac
eisa
extcon
firewire
firmware
fpga
fsi
gnss
gpio
gpu Wimplicit-fallthrough patches for 5.3-rc2 2019-07-27 11:04:18 -07:00
hid
hsi
hv
hwmon
hwspinlock
hwtracing
i2c
i3c
ide
idle
iio
infiniband
input
interconnect
iommu
ipack
irqchip
isdn
leds
lightnvm
macintosh
mailbox
mcb
md
media
memory
memstick
message
mfd
misc
mmc
mtd
mux
net Wimplicit-fallthrough patches for 5.3-rc2 2019-07-27 11:04:18 -07:00
nfc
ntb
nubus
nvdimm libnvdimm fixes v5.3-rc2 2019-07-27 08:25:51 -07:00
nvme
nvmem
of
opp
oprofile
parisc
parport
pci
pcmcia
perf
phy
pinctrl
platform
pnp
power
powercap
pps
ps3
ptp
pwm
rapidio
ras
regulator
remoteproc
reset
rpmsg
rtc
s390 s390/zcrypt: new sysfs attributes serialnr and mkvps 2019-07-29 18:14:17 +02:00
sbus
scsi SCSI fixes on 20190726 2019-07-26 14:20:28 -07:00
sfi
sh
siox
slimbus
sn
soc
soundwire
spi
spmi
ssb
staging
target
tc
tee
thermal
thunderbolt
tty TTY fixes for 5.3-rc2 2019-07-28 10:18:33 -07:00
uio
usb
uwb
vfio
vhost
video
virt
virtio
visorbus
vlynq
vme
w1
watchdog
xen
zorro
Kconfig
Makefile