On 32-bit systems, the buffer allocated by kernel_read_file() is too
small if the file size is > SIZE_MAX, due to truncation to size_t.
Fortunately, since the 'count' argument to kernel_read() is also
truncated to size_t, only the allocated space is filled; then, -EIO is
returned since 'pos != i_size' after the read loop.
But this is not obvious and seems incidental. We should be more
explicit about this case. So, fail early if i_size > SIZE_MAX.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Document that we actually work around ARM erratum 1188873
Fixes: 95b861a4a6 ("arm64: arch_timer: Add workaround for ARM erratum 1188873")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This reverts commit a1f33941f7.
The unsafe accessors allow the PAN enable/disable calls to be made
once for a group of accesses. Adding these means we can now have
sequences that look like this:
| user_access_begin();
| unsafe_put_user(static-value, x, err);
| unsafe_put_user(helper-that-sleeps(), x, err);
| user_access_end();
Calling schedule() without taking an exception doesn't switch the
PSTATE or TTBRs. We can switch out of a uaccess-enabled region, and
run other code with uaccess enabled for a different thread.
We can also switch from uaccess-disabled code back into this region,
meaning the unsafe_put_user()s will fault.
For software-PAN, threads that do this will get stuck as
handle_mm_fault() will determine the page has already been mapped in,
but we fault again as the page tables aren't loaded.
To solve this we need code in __switch_to() that save/restores the
PAN state.
Acked-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The major new feature here is nested HV KVM support. This allows the
HV KVM module to load inside a radix guest on POWER9 and run radix
guests underneath it. These nested guests can run in supervisor mode
and don't require any additional instructions to be emulated, unlike
with PR KVM, and so performance is much better than with PR KVM, and
is very close to the performance of a non-nested guest. A nested
hypervisor (a guest with nested guests) can be migrated to another
host and will bring all its nested guests along with it. A nested
guest can also itself run guests, and so on down to any desired depth
of nesting.
Apart from that there are a series of updates for IOMMU handling from
Alexey Kardashevskiy, a "one VM per core" mode for HV KVM for
security-paranoid applications, and a small fix for PR KVM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJbvY8iAAoJEJ2a6ncsY3GfMVAH/0t1nKifIr3KTKm+zR4peOU/
DMOTp/BomPCAlIJfp/C+j56GJ9H5me+i/ykTG6ZvHFhIInaM6OvavU7xQ7LBRvl1
ltjSr21IRO5BUWhnuDCYQXPFasJ0nX+LrKIRr7vNoUioUJHk6W1e4Mfep7CNs6fD
Q1p4Yg0BFCxN+ijhIOlQ49/ymbbaPFArOPh0mhipOEeY51NvCXYiUHiygu8RWnV9
sHuVFW3zQac0geUaWMAscVJ4dcvEw7GLXeY4FwWQtBPMq01LjJrECZcqy/c3Ut/2
06k7MpjZqPRneLp7aGznZCUjfQUMuP80ZRPQ8QLC/q1TODl+wPvB+hby1Q2tKvg=
=zAPd
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-next-4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into HEAD
PPC KVM update for 4.20.
The major new feature here is nested HV KVM support. This allows the
HV KVM module to load inside a radix guest on POWER9 and run radix
guests underneath it. These nested guests can run in supervisor mode
and don't require any additional instructions to be emulated, unlike
with PR KVM, and so performance is much better than with PR KVM, and
is very close to the performance of a non-nested guest. A nested
hypervisor (a guest with nested guests) can be migrated to another
host and will bring all its nested guests along with it. A nested
guest can also itself run guests, and so on down to any desired depth
of nesting.
Apart from that there are a series of updates for IOMMU handling from
Alexey Kardashevskiy, a "one VM per core" mode for HV KVM for
security-paranoid applications, and a small fix for PR KVM.
It is best to avoid any extra overhead associated with bio completion.
DM core will indirectly call a DM target's .end_io if it is defined.
In the case of DM linear, there is no need to do so (for every bio that
completes) if CONFIG_DM_ZONED is not enabled.
Avoiding an extra indirect call for every bio completion is very
important for ensuring DM linear doesn't incur more overhead that
further widens the performance gap between dm-linear and raw block
devices.
Fixes: 0be12c1c7f ("dm linear: add support for zoned block devices")
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Simplify the code by removing an unnecessary wrapper function.
This was left behind by commit 2f657add07
("iommu/arm-smmu-v3: Specialise CMD_SYNC handling")
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Replace license text with SDPX header
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Currently accessing various /sys/fs/orangefs files will spam the
kernel log with the following info message when the client is not
running:
[ 491.489284] sysfs_service_op_show: Client not running :-5:
Rate limit this info message to make it less spammy.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
default_acl and acl of newly created inode will be initiated
as ACL_NOT_CACHED in vfs function inode_init_always() and later
will be updated by calling xxx_init_acl() in specific filesystems.
Howerver, when default_acl and acl are NULL then they keep the value
of ACL_NOT_CACHED, this patch tries to cache NULL for acl/default_acl
in this case.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
PCI BIOS requires the BIOS area 0x0A0000-0x0FFFFFF to be mapped W+X for
various legacy reasons. When CONFIG_DEBUG_WX is enabled, this triggers the
WX warning, but this is misleading because the mapping is required and is
not a result of an accidental oversight.
Prevent the full warning when PCI BIOS is enabled and the detected WX
mapping is in the BIOS area. Just emit a pr_warn() which denotes the
fact. This is partially duplicating the info which the PCI BIOS code emits
when it maps the area as executable, but that info is not in the context of
the WX checking output.
Remove the extra %p printout in the WARN_ONCE() while at it. %pS is enough.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Borislav Petkov <bp@suse.de>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1810082151160.2455@nanos.tec.linutronix.de
On at least x86 and ARM64, and as documented in the ptrace man page
a skipped system call will still cause a syscall exit ptrace stop.
Previous to this commit 32-bit ARM did not, resulting in strace
being confused when seccomp skips system calls.
This change also impacts programs that use ptrace to skip system calls.
Fixes: ad75b51459 ("ARM: 7579/1: arch/allow a scno of -1 to not cause a SIGILL")
Signed-off-by: Timothy E Baldwin <T.E.Baldwin99@members.leeds.ac.uk>
Signed-off-by: Eugene Syromyatnikov <evgsyr@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: Eugene Syromyatnikov <evgsyr@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
spidev will make a big fuss if a device tree node binds a device by
using "spidev" as the node's compatible property.
However, the logic for this isn't looking for "spidev" in the
compatible, but rather checking that the device is NOT compatible with
spidev's list of devices.
This causes a false positive if a device not named "rohm,dh2228fv", etc.
binds to spidev, even if a means other than putting "spidev" in the
device tree was used. E.g., the sysfs driver_override attribute.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using skcipher just makes the code longer, and mac80211
also "open-codes" the WEP encrypt/decrypt.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This attribute works the same was as the identically named attribute
for PCI, AMBA, and platform devices. For reference, see:
commit 3cf3857134 ("ARM: 8256/1: driver coamba: add device binding
path 'driver_override'")
commit 3d713e0e38 ("driver core: platform: add device binding path
'driver_override'")
commit 782a985d7a ("PCI: Introduce new device binding path using
pci_dev.driver_override")
If the name of a driver is written to this attribute, then the device
will bind to the named driver and only the named driver.
The device will bind to the driver even if the driver does not list the
device in its id table. This behavior is different than the driver's
bind attribute, which only allows binding to devices that are listed as
supported by the driver.
It can be used to bind a generic driver, like spidev, to a device.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since 'commit 02e389e63e ("pinctrl: mcp23s08: fix irq setup order")' the
irq request isn't the last devm_* allocation. Without a deeper look at
the irq and testing this isn't a good solution. Since this driver relies
on the devm mechanism, requesting a interrupt should be the last thing
to avoid memory corruptions during unbinding.
'Commit 02e389e63e ("pinctrl: mcp23s08: fix irq setup order")' fixed the
order for the interrupt-controller use case only. The
mcp23s08_irq_setup() must be split into two to fix it for the
interrupt-controller use case and to register the irq at last. So the
irq will be freed first during unbind.
Cc: stable@vger.kernel.org
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Dmitry Mastykin <mastichi@gmail.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Fixes: 82039d244f ("pinctrl: mcp23s08: add pinconf support")
Fixes: 02e389e63e ("pinctrl: mcp23s08: fix irq setup order")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current audio-graph-card is supporting mclk-fs on CPU node
side only. But having Codec node also is good idea.
It will be just ignored if not defined.
"rcpu_ep" is same as "cpu_ep", This patch tidyup it, too.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit fb2815f44a ("ASoC: rsnd: add support for 16/24 bit slot widths")
added TDM width check, and return error if it was not 16/24/32 bit.
But it is too strict. This patch uses 32bit same as default.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
max98988 only builds with I2C support enabled, otherwise we get a build error:
sound/soc/codecs/max98088.c:1789:1: error: data definition has no type or storage class [-Werror]
module_i2c_driver(max98088_i2c_driver);
^~~~~~~~~~~~~~~~~
sound/soc/codecs/max98088.c:1789:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
sound/soc/codecs/max98088.c:1789:1: error: parameter names (without types) in function declaration [-Werror]
sound/soc/codecs/max98088.c:1780:26: error: 'max98088_i2c_driver' defined but not used [-Werror=unused-variable]
Fixes: 24ae67c582 ("ASoC: max98988: make it selectable")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
gpiochip_set_cascaded_irqchip() is passed 'parent_irq' as an argument
and then the address of that argument is assigned to the gpio chips
gpio_irq_chip 'parents' pointer shortly thereafter. This can't ever
work, because we've just assigned some stack address to a pointer that
we plan to dereference later in gpiochip_irq_map(). I ran into this
issue with the KASAN report below when gpiochip_irq_map() tried to setup
the parent irq with a total junk pointer for the 'parents' array.
BUG: KASAN: stack-out-of-bounds in gpiochip_irq_map+0x228/0x248
Read of size 4 at addr ffffffc0dde472e0 by task swapper/0/1
CPU: 7 PID: 1 Comm: swapper/0 Not tainted 4.14.72 #34
Call trace:
[<ffffff9008093638>] dump_backtrace+0x0/0x718
[<ffffff9008093da4>] show_stack+0x20/0x2c
[<ffffff90096b9224>] __dump_stack+0x20/0x28
[<ffffff90096b91c8>] dump_stack+0x80/0xbc
[<ffffff900845a350>] print_address_description+0x70/0x238
[<ffffff900845a8e4>] kasan_report+0x1cc/0x260
[<ffffff900845aa14>] __asan_report_load4_noabort+0x2c/0x38
[<ffffff900897e098>] gpiochip_irq_map+0x228/0x248
[<ffffff900820cc08>] irq_domain_associate+0x114/0x2ec
[<ffffff900820d13c>] irq_create_mapping+0x120/0x234
[<ffffff900820da78>] irq_create_fwspec_mapping+0x4c8/0x88c
[<ffffff900820e2d8>] irq_create_of_mapping+0x180/0x210
[<ffffff900917114c>] of_irq_get+0x138/0x198
[<ffffff9008dc70ac>] spi_drv_probe+0x94/0x178
[<ffffff9008ca5168>] driver_probe_device+0x51c/0x824
[<ffffff9008ca6538>] __device_attach_driver+0x148/0x20c
[<ffffff9008ca14cc>] bus_for_each_drv+0x120/0x188
[<ffffff9008ca570c>] __device_attach+0x19c/0x2dc
[<ffffff9008ca586c>] device_initial_probe+0x20/0x2c
[<ffffff9008ca18bc>] bus_probe_device+0x80/0x154
[<ffffff9008c9b9b4>] device_add+0x9b8/0xbdc
[<ffffff9008dc7640>] spi_add_device+0x1b8/0x380
[<ffffff9008dcbaf0>] spi_register_controller+0x111c/0x1378
[<ffffff9008dd6b10>] spi_geni_probe+0x4dc/0x6f8
[<ffffff9008cab058>] platform_drv_probe+0xdc/0x130
[<ffffff9008ca5168>] driver_probe_device+0x51c/0x824
[<ffffff9008ca59cc>] __driver_attach+0x100/0x194
[<ffffff9008ca0ea8>] bus_for_each_dev+0x104/0x16c
[<ffffff9008ca58c0>] driver_attach+0x48/0x54
[<ffffff9008ca1edc>] bus_add_driver+0x274/0x498
[<ffffff9008ca8448>] driver_register+0x1ac/0x230
[<ffffff9008caaf6c>] __platform_driver_register+0xcc/0xdc
[<ffffff9009c4b33c>] spi_geni_driver_init+0x1c/0x24
[<ffffff9008084cb8>] do_one_initcall+0x240/0x3dc
[<ffffff9009c017d0>] kernel_init_freeable+0x378/0x468
[<ffffff90096e8240>] kernel_init+0x14/0x110
[<ffffff9008086fcc>] ret_from_fork+0x10/0x18
The buggy address belongs to the page:
page:ffffffbf037791c0 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x4000000000000000()
raw: 4000000000000000 0000000000000000 0000000000000000 00000000ffffffff
raw: ffffffbf037791e0 ffffffbf037791e0 0000000000000000 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffffffc0dde47180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffffc0dde47200: f1 f1 f1 f1 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f2 f2
>ffffffc0dde47280: f2 f2 00 00 00 00 00 00 00 00 00 00 f3 f3 f3 f3
^
ffffffc0dde47300: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffffc0dde47380: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Let's leave around one unsigned int in the gpio_irq_chip struct for the
single parent irq case and repoint the 'parents' array at it. This way
code is left mostly intact to setup parents and we waste an extra few
bytes per structure of which there should be only a handful in a system.
Cc: Evan Green <evgreen@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Fixes: e0d8972898 ("gpio: Implement tighter IRQ chip integration")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When powering down a SDIO connected card during suspend, make sure to call
into the generic lbs_suspend() function before pulling the plug. This will
make sure the card is successfully deregistered from the system to avoid
communication to the card starving out.
Fixes: 7444a80929 ("libertas: fix suspend and resume for SDIO connected cards")
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code was written under the assumption that the
regmap_update_bits() would mask the bits in the mask and
set the bits in the value.
It missed the points that it will not set bits in the value
unless these are also masked in the mask. Set value bits
that are not in the mask will simply be ignored.
Fixes: 06351d133d ("pinctrl: add a Gemini SoC pin controller")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Removing the linux/gpio.h include means we no longer have a declaration
of gpiochip_lock_as_irq() when CONFIG_GPIOLIB is disabled:
drivers/pinctrl/mediatek/mtk-eint.c: In function 'mtk_eint_irq_request_resources':
drivers/pinctrl/mediatek/mtk-eint.c:247:8: error: implicit declaration of function 'gpiochip_lock_as_irq'; did you mean 'spin_lock_irq'? [-Werror=implicit-function-declaration]
drivers/pinctrl/mediatek/mtk-eint.c: In function 'mtk_eint_irq_release_resources':
drivers/pinctrl/mediatek/mtk-eint.c:272:2: error: implicit declaration of function 'gpiochip_unlock_as_irq'; did you mean 'spin_unlock_irq'? [-Werror=implicit-function-declaration]
Select it explictly instead.
Fixes: 1c5fb66afa ("pinctrl: Include <linux/gpio/driver.h> nothing else")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On systems with OF_IMAP_OLDWORLD_MAC set in of_irq_workarounds, the
devicetree interrupt parsing code is different, causing unit tests of
devicetree interrupt nodes to fail. Due to a bug in unittest code, which
tries to dereference an uninitialized pointer, this results in a crash.
OF: /testcase-data/phandle-tests/consumer-a: arguments longer than property
Unable to handle kernel paging request for data at address 0x00bc616e
Faulting instruction address: 0xc08e9468
Oops: Kernel access of bad area, sig: 11 [#1]
BE PREEMPT PowerMac
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.14.72-rc1-yocto-standard+ #1
task: cf8e0000 task.stack: cf8da000
NIP: c08e9468 LR: c08ea5bc CTR: c08ea5ac
REGS: cf8dbb50 TRAP: 0300 Not tainted (4.14.72-rc1-yocto-standard+)
MSR: 00001032 <ME,IR,DR,RI> CR: 82004044 XER: 00000000
DAR: 00bc616e DSISR: 40000000
GPR00: c08ea5bc cf8dbc00 cf8e0000 c13ca517 c13ca517 c13ca8a0 00000066 00000002
GPR08: 00000063 00bc614e c0b05865 000affff 82004048 00000000 c00047f0 00000000
GPR16: c0a80000 c0a9cc34 c13ca517 c0ad1134 05ffffff 000affff c0b05860 c0abeef8
GPR24: cecec278 cecec278 c0a8c4d0 c0a885e0 c13ca8a0 05ffffff c13ca8a0 c13ca517
NIP [c08e9468] device_node_gen_full_name+0x30/0x15c
LR [c08ea5bc] device_node_string+0x190/0x3c8
Call Trace:
[cf8dbc00] [c007f670] trace_hardirqs_on_caller+0x118/0x1fc (unreliable)
[cf8dbc40] [c08ea5bc] device_node_string+0x190/0x3c8
[cf8dbcb0] [c08eb794] pointer+0x25c/0x4d0
[cf8dbd00] [c08ebcbc] vsnprintf+0x2b4/0x5ec
[cf8dbd60] [c08ec00c] vscnprintf+0x18/0x48
[cf8dbd70] [c008e268] vprintk_store+0x4c/0x22c
[cf8dbda0] [c008ecac] vprintk_emit+0x94/0x130
[cf8dbdd0] [c008ff54] printk+0x5c/0x6c
[cf8dbe10] [c0b8ddd4] of_unittest+0x2220/0x26f8
[cf8dbea0] [c0004434] do_one_initcall+0x4c/0x184
[cf8dbf00] [c0b4534c] kernel_init_freeable+0x13c/0x1d8
[cf8dbf30] [c0004814] kernel_init+0x24/0x118
[cf8dbf40] [c0013398] ret_from_kernel_thread+0x5c/0x64
The problem was observed when running a qemu test for the g3beige machine
with devicetree unittests enabled.
Disable interrupt node tests on affected systems to avoid both false
unittest failures and the crash.
With this patch in place, unittest on the affected system passes with
the following message.
dt-test ### end of unittest - 144 passed, 0 failed
Fixes: 53a42093d9 ("of: Add device tree selftests")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Certain devices don't work well when a transmit FIFO underrun or
receive FIFO overrun occurs. Example is the SAF400x radio chip when
running at high speed which leads to garbage being sent to/received from
the chip. In which case, it should stall waiting for further data to be
available before proceeding. This patch unset the NOSTALL bit in CFGR1
by default to prevent this issue.
Signed-off-by: Hieu Tran Dang <dangtranhieu2012@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function is about adding a gpio_chip so dev has to belong to this
one. Fix wording to be more grammatically correct (but attention, I'm
not a native speaker).
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-EINVAL is not a valid return value for .of_map_mode, return
REGULATOR_MODE_INVALID instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In former commits, .private_free callback releases resources just for
data transmission. This release function can be called without the
resources are actually allocated in error paths.
This commit applies a small refactoring to clean up codes in error
paths.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In drivers of ALSA firewire stack, bebob and fireworks drivers have
local device entry table. At present, critical section to operate the
table is from the beginning/end of 'do_registration' call. This can be
more narrow and simplify codes.
This commit applies small refactoring for the above purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a previous commit, drivers in ALSA firewire stack blocks .remove
callback of bus driver. This enables to release members of private
data in the callback after releasing device of sound card.
This commit simplifies codes to release the members.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At present, in .remove callback of bus driver just decrease reference
count of device for ALSA card instance. This delegates release of the
device to a process in which the last of ALSA character device is
released.
On the other hand, the other drivers such as for devices on PCIe are
programmed to block .remove callback of bus driver till all of ALSA
character devices are released.
For consistency of behaviour for whole drivers, this probably confuses
users. This commit takes drivers in ALSA firewire stack to imitate the
above behaviour.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the probe function fails the driver core cares to return the allocated
resources automatically. So the driver can be simplified accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add support for the new RZ/N1D (R9A06G032) and RZ/N1S (R9A06G033)
SoCs,
- Add INTC-EX pin groups on R-Car E3.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCW7dQmQAKCRCKwlD9ZEnx
cB04AQCj1PoCEotqH9TGaGeVXal35LUMP279vz3HoJweY0DF2AD/QKd/jC2mHz/c
EypfJAvBvckw9AsdfNSacrCIdMNg7gE=
=gtgr
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.20-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.20 (take three)
- Add support for the new RZ/N1D (R9A06G032) and RZ/N1S (R9A06G033)
SoCs,
- Add INTC-EX pin groups on R-Car E3.
Add all source files under drivers/pinctrl/mediatek for the entry and
change the address to a permanent one since I have a personal leave
over the next few months and the address would be suspended for a while.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case the RSDP address in struct boot_params is specified don't try
to find the table by searching, but take the address directly as set
by the boot loader.
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jia Zhang <qianyue.zj@alibaba-inc.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Pavel Tatashin <pasha.tatashin@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: boris.ostrovsky@oracle.com
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20181010061456.22238-4-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Xen PVH guests receive the address of the RSDP table from Xen. In order
to support booting a Xen PVH guest via Grub2 using the standard x86
boot entry we need a way for Grub2 to pass the RSDP address to the
kernel.
For this purpose expand the struct setup_header to hold the physical
address of the RSDP address. Being zero means it isn't specified and
has to be located the legacy way (searching through low memory or
EBDA).
While documenting the new setup_header layout and protocol version
2.14 add the missing documentation of protocol version 2.13.
There are Grub2 versions in several distros with a downstream patch
violating the boot protocol by writing past the end of setup_header.
This requires another update of the boot protocol to enable the kernel
to distinguish between a specified RSDP address and one filled with
garbage by such a broken Grub2.
From protocol 2.14 on Grub2 will write the version it is supporting
(but never a higher value than found to be supported by the kernel)
ored with 0x8000 to the version field of setup_header. This enables
the kernel to know up to which field Grub2 has written information
to. All fields after that are supposed to be clobbered.
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: boris.ostrovsky@oracle.com
Cc: bp@alien8.de
Cc: corbet@lwn.net
Cc: linux-doc@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20181010061456.22238-3-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The boot loader version reported via sysfs is wrong in case of the
kernel being booted via the Xen PVH boot entry. it should be 2.12
(0x020c), but it is reported to be 2.18 (0x0212).
As the current way to set the version is error prone use the more
readable variant (2 << 8) | 12.
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: <stable@vger.kernel.org> # 4.12
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: boris.ostrovsky@oracle.com
Cc: bp@alien8.de
Cc: corbet@lwn.net
Cc: linux-doc@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20181010061456.22238-2-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The priv->data->set can be NULL while flags contains GPIO_SYSCON_FEAT_OUT
and chip->set is valid pointer. This happens in case the controller uses
the default GPIO setter. Always use chip->set to access the setter to avoid
possible NULL pointer dereferencing.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current code assumes that the direction is input if direction_input
function is set.
This might not be the case on GPIOs with programmable direction.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current code produces XPU violation if get_direction is called just
after the initialization.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a function that allows initializing the valid_mask from
gpiochip_add_data.
This prevents race conditions during gpiochip initialization.
If the function is not exported, then the old behaviour is respected,
this is, set all gpios as valid.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add single-register MMIO GPIO driver for complex cases where
only several fields in register belong to GPIO lines and each GPIO
line owns a field with different length and on/off value.
Such CREG GPIOs are used in Synopsys AXS10x and HSDK boards.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds documentation of device tree bindings for the Synopsys
GPIO via CREG driver.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver provides support for Northstar mux controller. It differs
from Northstar Plus one so a new binding and driver were needed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
