ZYNQMP_PM_CAPABILITY_POWER capability is not supported by firmware
and hence needs to be removed
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces fabrics commands tracing feature from host-side.
This patch does not include any changes for the previous host-side
tracing, but just add fabrics commands parsing in cmd=() format.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
[hch: fixed some whitespace damage]
Signed-off-by: Christoph Hellwig <hch@lst.de>
The following patches are going to provide the target-side trace which
might need these kind of macros. It would be great if it can be shared
between host and target side both.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch introduces a nvme_is_fabrics() inline function to check
whether or not the given command structure is for fabrics.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds support for the nvmet discovery_change transport op.
In turn, the transport adds it's own LLDD api callback discovery_event
op to request the LLDD to generate an RSCN for the discovery change.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.
Changed by Stefan:
Only call mctrl_gpio_init(), if the device has no ACPI companion device
to not break existing ACPI based systems. Also only use the mctrl_gpio_
functions when "gpios" is available.
Use MSR / MCR <-> TIOCM wrapper functions.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UAPI Changes:
- Give each dma-buf their own inode, add DMA_BUF_SET_NAME ioctl and a show_fdinfo handler.
Cross-subsystem Changes:
- Pull in the topic/remove-fbcon-notifiers branch:
* remove fbdev notifier usage for fbcon, as prep work to clean up the fbcon locking
* assorted locking checks in vt/console code
* assorted notifier and cleanups in fbdev and backlight code
Core Changes:
- Make drm_debugfs_create_files() never fail.
- add debug print to update_vblank_count.
- Add DP_DPCD_QUIRK_NO_SINK_COUNT quirk.
- Add todo item for drm_gem_objects.
- Unexport drm_gem_(un)pin/v(un)map.
- Document struct drm_cmdline_mode.
- Rewrite the command handler for mode names, and add support to specify
rotation, reflection and overscan. With a new selftest! :)
- Fixes to drm/client for improving rotation support, and fixing variable scope.
- Small fixes to self refresh helper.
Driver Changes:
- Add rockchip RK3328 support.
- Assorted driver fixes to rockchip, vc4, rcar-du, vkms.
- Expose panfrost performance counters through unstable ioctl's, hidden
behind a module parameter.
- Enumerate CRC sources list in vkms.
- Add a basic kms driver for the Ingenic JZ47xx SoC, which will be expanded
soon with more advanced features.
- Suspend/resume fix for stm.
-----BEGIN PGP SIGNATURE-----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=A67v
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-06-20' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3:
UAPI Changes:
- Give each dma-buf their own inode, add DMA_BUF_SET_NAME ioctl and a show_fdinfo handler.
Cross-subsystem Changes:
- Pull in the topic/remove-fbcon-notifiers branch:
* remove fbdev notifier usage for fbcon, as prep work to clean up the fbcon locking
* assorted locking checks in vt/console code
* assorted notifier and cleanups in fbdev and backlight code
Core Changes:
- Make drm_debugfs_create_files() never fail.
- add debug print to update_vblank_count.
- Add DP_DPCD_QUIRK_NO_SINK_COUNT quirk.
- Add todo item for drm_gem_objects.
- Unexport drm_gem_(un)pin/v(un)map.
- Document struct drm_cmdline_mode.
- Rewrite the command handler for mode names, and add support to specify
rotation, reflection and overscan. With a new selftest! :)
- Fixes to drm/client for improving rotation support, and fixing variable scope.
- Small fixes to self refresh helper.
Driver Changes:
- Add rockchip RK3328 support.
- Assorted driver fixes to rockchip, vc4, rcar-du, vkms.
- Expose panfrost performance counters through unstable ioctl's, hidden
behind a module parameter.
- Enumerate CRC sources list in vkms.
- Add a basic kms driver for the Ingenic JZ47xx SoC, which will be expanded
soon with more advanced features.
- Suspend/resume fix for stm.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/18e22ec1-adf3-3a75-34a3-9fe09a91eef5@linux.intel.com
The journal_sync_buffer() function was never carried over from jbd to
jbd2. So get rid of the vestigal declaration of this (non-existent)
function.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Currently both journal_submit_inode_data_buffers() and
journal_finish_inode_data_buffers() operate on the entire address space
of each of the inodes associated with a given journal entry. The
consequence of this is that if we have an inode where we are constantly
appending dirty pages we can end up waiting for an indefinite amount of
time in journal_finish_inode_data_buffers() while we wait for all the
pages under writeback to be written out.
The easiest way to cause this type of workload is do just dd from
/dev/zero to a file until it fills the entire filesystem. This can
cause journal_finish_inode_data_buffers() to wait for the duration of
the entire dd operation.
We can improve this situation by scoping each of the inode dirty ranges
associated with a given transaction. We do this via the jbd2_inode
structure so that the scoping is contained within jbd2 and so that it
follows the lifetime and locking rules for that structure.
This allows us to limit the writeback & wait in
journal_submit_inode_data_buffers() and
journal_finish_inode_data_buffers() respectively to the dirty range for
a given struct jdb2_inode, keeping us from waiting forever if the inode
in question is still being appended to.
Signed-off-by: Ross Zwisler <zwisler@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: stable@vger.kernel.org
In the spirit of filemap_fdatawait_range() and
filemap_fdatawait_keep_errors(), introduce
filemap_fdatawait_range_keep_errors() which both takes a range upon
which to wait and does not clear errors from the address space.
Signed-off-by: Ross Zwisler <zwisler@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: stable@vger.kernel.org
sg_alloc_table_chained() currently allows the caller to provide one
preallocated SGL and returns if the requested number isn't bigger than
size of that SGL. This is used to inline an SGL for an IO request.
However, scattergather code only allows that size of the 1st preallocated
SGL to be SG_CHUNK_SIZE(128). This means a substantial amount of memory
(4KB) is claimed for the SGL for each IO request. If the I/O is small, it
would be prudent to allocate a smaller SGL.
Introduce an extra parameter to sg_alloc_table_chained() and
sg_free_table_chained() for specifying size of the preallocated SGL.
Both __sg_free_table() and __sg_alloc_table() assume that each SGL has the
same size except for the last one. Change the code to allow both functions
to accept a variable size for the 1st preallocated SGL.
[mkp: attempted to clarify commit desc]
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: netdev@vger.kernel.org
Cc: linux-nvme@lists.infradead.org
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In order to centralize the REQ_OP_XXX to string conversion which can be
used in the block layer and different places in the kernel like f2fs,
this patch adds a new helper function along with an array similar to the
one present in the blk-mq-debugfs.c.
We keep this helper functionality centralize under blk-core.c instead of
blk-mq-debugfs.c since blk-core.c is configured using CONFIG_BLOCK and
it will not be dependent on blk-mq-debugfs.c which is configured using
CONFIG_BLK_DEBUG_FS.
Next patch adjusts the code in the blk-mq-debugfs.c with newly
introduced helper.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEq1nRK9aeMoq1VSgcnJ2qBz9kQNkFAl0LhAIACgkQnJ2qBz9k
QNnUqwf/d7fNZv0+GJVBIrIVbSUgHqzJYxakMWAS6NGMmd2fkPcoPRHitXWbi5MJ
fhJPFceNVqY30RPQUePlDmWSitEDI0kdaNZ3Z8SzE9YszaEgoLNAN/dpOuPGpQfh
kXQd7yM1cBZJoAv5kQsECiYXfY7nk+3J+DVsu69rBcsooxT5rfXs00Dz9ETao9gK
L1SR/s5C6b2t0m0EfQpv/+PjbzPQPLKngvihvFesAT6lSA6QpRMY7M8+4Es3rzuI
7h0kuThkJaIp9B+D9C8vYIT+uVQVjsN9wXozJHXRNvnK/4mfDvYJdWSkRhqP5p1a
DBRo/jK8meV1ZvIEsLjARxHg0z7yAA==
=PlCd
-----END PGP SIGNATURE-----
Merge tag 'for_v5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull two misc vfs fixes from Jan Kara:
"One small quota fix fixing spurious EDQUOT errors and one fanotify fix
fixing a bug in the new fanotify FID reporting code"
* tag 'for_v5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fanotify: update connector fsid cache on add mark
quota: fix a problem about transfer quota
- Make switch to eMMC HS400 more robust for some controllers
- Add two SDIO func API to manage re-tuning constraints
- Prevent processing SDIO IRQs when the card is suspended
MMC host:
- sdhi: Disallow broken HS400 for M3-W ES1.2, RZ/G2M and V3H
- mtk-sd: Fixup support for SDIO IRQs
- sdhci-pci-o2micro: Fixup support for tuning
Wireless BRCMFMAC (SDIO):
- Deal with expected transmission errors related to the idle states
(handled by the Always-On-Subsystem or AOS) on the SDIO-based WiFi on
rk3288-veyron-minnie, rk3288-veyron-speedy and rk3288-veyron-mickey.
-----BEGIN PGP SIGNATURE-----
iQJLBAABCgA1FiEEugLDXPmKSktSkQsV/iaEJXNYjCkFAl0LaFgXHHVsZi5oYW5z
c29uQGxpbmFyby5vcmcACgkQ/iaEJXNYjCnnkg//f4s1IsuIQjifX1+0crD3xSPF
ZFvn7LMldslZxIfXzwJxvp50ZA6KUZVUpAlmTFev1Dbz+SoYJvOYxXIcv0/ASQYn
t2f0qNSI3Mw9vQa2S2PMYyThO8KSoqtu0Z3gXdSjGgox6et3g9HMW/ubOuj+91Gx
UhkVd7B0O6uY83CxJWnhEMuDS5iMhuZJ0HMFk6R1XrtsCJf9T1jZMYa2iJ1247TZ
pChYrfw1NJzUDEzGOlUlShGRUdqLjcNeSj2gN50O2GZpPeZnnSwabdOd0OcyE7rH
563GxCz0GZRLs8cCxzp+9OirQER7+ZBK/e9Q34MVcNsmx/FwEclg1dfhscOZhll3
27NBf16sAyas54MhDaMRmh2SQfqucEO4M4Wn0QzP/eo1t9o2MZiwY/iw+NRC6SDm
V2tVd7rRNly1I3KlmYEOAEYC2f1UXXyb8LYa8+D6g9CSQGcf0HrqoUzHESDCf1eF
hU6JaijQQhs2sDqsH6Hyg0i5yACm68RQhpfTTTMHXbDLTzVZbChVlsox3YszHsFt
8eOWS/LeGI058i40EKa4ulbbCjMmGoghYneyTBQSKBYGiJwIVpvZGqje+Nmfo3rw
o4d+OTzM2qdkAk0GZs9o0/xWj00LU43C8W0NO6MV/WgKaysk+WNueawrZWV7/nL3
up0ea93jvrwpUf3f2jw=
=IkL6
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"Here's quite a few MMC fixes intended for v5.2-rc6. This time it also
contains fixes for a WiFi driver, which device is attached to the SDIO
interface. Patches for the WiFi driver have been acked by the
corresponding maintainers.
Summary:
MMC core:
- Make switch to eMMC HS400 more robust for some controllers
- Add two SDIO func API to manage re-tuning constraints
- Prevent processing SDIO IRQs when the card is suspended
MMC host:
- sdhi: Disallow broken HS400 for M3-W ES1.2, RZ/G2M and V3H
- mtk-sd: Fixup support for SDIO IRQs
- sdhci-pci-o2micro: Fixup support for tuning
Wireless BRCMFMAC (SDIO):
- Deal with expected transmission errors related to the idle states
(handled by the Always-On-Subsystem or AOS) on the SDIO-based WiFi
on rk3288-veyron-minnie, rk3288-veyron-speedy and
rk3288-veyron-mickey"
* tag 'mmc-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: Prevent processing SDIO IRQs when the card is suspended
mmc: sdhci: sdhci-pci-o2micro: Correctly set bus width when tuning
brcmfmac: sdio: Don't tune while the card is off
mmc: core: Add sdio_retune_hold_now() and sdio_retune_release()
brcmfmac: sdio: Disable auto-tuning around commands expected to fail
mmc: core: API to temporarily disable retuning for SDIO CRC errors
Revert "brcmfmac: disable command decode in sdio_aos"
mmc: mediatek: fix SDIO IRQ detection issue
mmc: mediatek: fix SDIO IRQ interrupt handle flow
mmc: core: complete HS400 before checking status
mmc: sdhi: disallow HS400 for M3-W ES1.2, RZ/G2M, and V3H
-----BEGIN PGP SIGNATURE-----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=rUI5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190620' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Three fixes that should go into this series.
One is a set of two patches from Christoph, fixing a page leak on same
page merges. Boiled down version of a bigger fix, but this one is more
appropriate for this late in the cycle (and easier to backport to
stable).
The last patch is for a divide error in MD, from Mariusz (via Song)"
* tag 'for-linus-20190620' of git://git.kernel.dk/linux-block:
md: fix for divide error in status_resync
block: fix page leak when merging to same page
block: return from __bio_try_merge_page if merging occured in the same page
This structure and assorted infrastructure is only used by the bfq I/O
scheduler. Move it there instead of bloating the common code.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When sampling the blkcg counts we don't need atomics or per-cpu
variables. Introduce a new structure just containing plain u64
counters.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Returning a structure generates rather bad code, so switch to passing
by reference. Also don't require the structure to be zeroed and add
to the 0-initialized counters, but actually set the counters to the
calculated value.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Trying to break up the crazy statements to something readable.
Also switch to an unsigned counter as it can't ever turn negative.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We only need the number of segments in the blk-mq submission path.
Remove the field from struct bio, and return it from a variant of
blk_queue_split instead of that it can passed as an argument to
those functions that need the value.
This also means we stop recounting segments except for cloning
and partial segments.
To keep the number of arguments in this how path down remove
pointless struct request_queue arguments from any of the functions
that had it and grew a nr_segs argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
lightnvm should have never used this function, as it is sending
passthrough requests, so switch it to blk_rq_append_bio like all the
other passthrough request users. Inline blk_init_request_from_bio into
the only remaining caller.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All external users of sdio_run_irqs() have converted into using the
preferred sdio_signal_irq() interface, thus not calling the function
directly any more. Avoid further new users of it, by turning it into
static.
Suggested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For all callers of fsnotify_{unlink,rmdir}(), we made sure that d_parent
and d_name are stable. Therefore, fsnotify_{unlink,rmdir}() do not need
the safety measures in fsnotify_nameremove() to stabilize parent and name.
We can now simplify those hooks and get rid of fsnotify_nameremove().
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
d_delete() was piggy backed for the fsnotify_nameremove() hook when
in fact not all callers of d_delete() care about fsnotify events.
For all callers of d_delete() that may be interested in fsnotify events,
we made sure to call one of fsnotify_{unlink,rmdir}() hooks before
calling d_delete().
Now we can move the fsnotify_nameremove() call from d_delete() to the
fsnotify_{unlink,rmdir}() hooks.
Two explicit calls to fsnotify_nameremove() from nfs/afs sillyrename
are also removed. This will cause a change of behavior - nfs/afs will
NOT generate an fsnotify delete event when renaming over a positive
dentry. This change is desirable, because it is consistent with the
behavior of all other filesystems.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
We would like to move fsnotify_nameremove() calls from d_delete()
into a higher layer where the hook makes more sense and so we can
consider every d_delete() call site individually.
Start by creating empty hook fsnotify_{unlink,rmdir}() and place
them in the proper VFS call sites. After all d_delete() call sites
will be converted to use the new hook, the new hook will generate the
delete events and fsnotify_nameremove() hook will be removed.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
According to the DA9061 and DA9062 datasheets the LDO voltage selection
registers have a lower value of 0x02. This applies to voltage registers
VLDO1_A, VLDO2_A, VLDO3_A and VLDO4_A. This linear offset of 0x02 was
previously not observed by the driver, causing the LDO output voltage to
be systematically lower by two steps (= 0.1V).
This patch fixes the minimum linear selector offset by setting it to a
value of 2 and increases the n_voltages by the same amount allowing
voltages in the range 0x02 -> 0.9V to 0x38 -> 3.6V to be correctly
selected. Also fixes an incorrect calculaton for the n_voltages value in
the regulator LDO2.
These fixes effect all LDO regulators for DA9061 and DA9062.
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Felix Riemann <felix.riemann@sma.de>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Cirrus Logic Madera codecs are a family of related codecs with
extensive digital and analogue I/O, digital mixing and routing,
signal processing and programmable DSPs. This patch adds common
support code shared by all Madera codecs.
This patch also adds the pdata to the parent mfd pdata struct.
Since there is a circular build dependency it's convenient to
patch them both atomically.
Signed-off-by: Nariman Poushin <nariman@opensource.cirrus.com>
Signed-off-by: Nikesh Oswal <Nikesh.Oswal@cirrus.com>
Signed-off-by: Piotr Stankiewicz <piotrs@opensource.cirrus.com>
Signed-off-by: Ajit Pandey <ajit.pandey@incubesol.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When either CONFIG_IPV6 or CONFIG_SYN_COOKIES are disabled, the kernel
fails to build:
include/linux/netfilter_ipv6.h:180:9: error: implicit declaration of function '__cookie_v6_init_sequence'
[-Werror,-Wimplicit-function-declaration]
return __cookie_v6_init_sequence(iph, th, mssp);
include/linux/netfilter_ipv6.h:194:9: error: implicit declaration of function '__cookie_v6_check'
[-Werror,-Wimplicit-function-declaration]
return __cookie_v6_check(iph, th, cookie);
net/ipv6/netfilter.c:237:26: error: use of undeclared identifier '__cookie_v6_init_sequence'; did you mean 'cookie_init_sequence'?
net/ipv6/netfilter.c:238:21: error: use of undeclared identifier '__cookie_v6_check'; did you mean '__cookie_v4_check'?
Fix the IS_ENABLED() checks to match the function declaration
and definitions for these.
Fixes: 3006a5224f ("netfilter: synproxy: remove module dependency on IPv6 SYNPROXY")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit a1ce35fa49 ("block: remove dead elevator code")
deleted blk_end_request() and friends, but some declaration are still
left. Purge them.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
__data_len and __sector are internal fields which should not be accessed
directly in driver-level like the comment above it. But, tag field can
be accessed by driver level directly so that we need to make the comment
right by moving it to some other place.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
On ioremap(), __ioremap_check_mem() does a couple of checks on the
supplied memory range to determine how the range should be mapped and in
particular what protection flags should be used.
Generalize the procedure by introducing IORES_MAP_* flags which control
different aspects of the ioremapping and use them in the respective
helpers which determine which descriptor flags should be set per range.
[ bp:
- Rewrite commit message.
- Add/improve comments.
- Reflow __ioremap_caller()'s args.
- s/__ioremap_check_desc/__ioremap_check_encrypted/g;
- s/__ioremap_res_check/__ioremap_collect_map_flags/g;
- clarify __ioremap_check_ram()'s purpose. ]
Signed-off-by: Lianbo Jiang <lijiang@redhat.com>
Co-developed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: bhe@redhat.com
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: dyoung@redhat.com
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: kexec@lists.infradead.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190423013007.17838-3-lijiang@redhat.com
When executing the kexec_file_load() syscall, the first kernel needs to
pass the e820 reserved ranges to the second kernel because some devices
(PCI, for example) need them present in the kdump kernel for proper
initialization.
But the kernel can not exactly match the e820 reserved ranges when
walking through the iomem resources using the default IORES_DESC_NONE
descriptor, because there are several types of e820 ranges which are
marked IORES_DESC_NONE, see e820_type_to_iores_desc().
Therefore, add a new I/O resource descriptor called IORES_DESC_RESERVED
to mark exactly those ranges. It will be used to match the reserved
resource ranges when walking through iomem resources.
[ bp: Massage commit message. ]
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Lianbo Jiang <lijiang@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: bhe@redhat.com
Cc: dave.hansen@linux.intel.com
Cc: dyoung@redhat.com
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Huang Zijiang <huang.zijiang@zte.com.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: kexec@lists.infradead.org
Cc: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190423013007.17838-2-lijiang@redhat.com
The i3c bus spec defines a bus configuration where i2c devices don't
have a 50ns filter but support SCL running at SDR max rate (12.5MHz).
This patch introduces the limited bus mode so that users can use
a higher speed in presence of i2c devices index 1.
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
So far we have reused the name of the "platform" device for
the CoreSight device. But this is not very intuitive when
we move to ACPI. Also, the ACPI device names have ":" in them
(e.g, ARMHC97C:01), which the perf tool doesn't like very much.
This patch introduces a generic naming scheme, givin more intuitive
names for the devices that appear on the CoreSight bus.
The names follow the pattern "prefix" followed by "index" (e.g, etm5).
We maintain a list of allocated devices per "prefix" to make sure
we don't allocate a new name when it is reprobed (e.g, due to
unsatisifed device dependencies). So, we maintain the list
of "fwnodes" of the parent devices to allocate a consistent name.
All devices except the ETMs get an index allocated in the order
of probing. ETMs get an index based on the CPU they are attached to.
TMC devices are named using "tmc_etf", "tmc_etb", and "tmc_etr"
prefixes depending on the configuration of the device.
The replicators and funnels are not classified as dynamic/static
anymore. One could easily figure that out by checking the presence
of "mgmt" registers under sysfs.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We rely on the device names to find a CoreSight device on the
coresight bus. The device name however is obtained from the platform,
which is bound to the real platform/amba device. As we are about
to use different naming scheme for the coresight devices, we can't
rely on the platform device name to find the corresponding
coresight device. Instead we use the platform agnostic
"fwnode handle" of the parent device to find the devices.
We also reuse the same fwnode as the parent for the Coresight
device we create.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform specific information describes the connections and
the ports of a given coresigh device. This information is also
recorded in the coresight device as separate fields. Let us reuse
the original platform description to streamline the handling
of the data.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are about to use a name independent of the parent AMBA device
name. As such, there is no need to have it in the platform description.
Let us move this to coresight description instead.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CPU field is only used by ETMs and there is a separate API
for fetching the same. So, let us use that instead of using
the common platform probing helper. Also, remove it from the
platform_data.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CoreSight components ETM and CPU-Debug are always associated
with CPUs. Replace the of_coresight_get_cpu() with a platform
agnostic helper, in preparation to add ACPI support.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far we have hard coded the DT platform parsing code in
every driver. Introduce generic helper to parse the information
provided by the firmware in a platform agnostic manner, in preparation
for the ACPI support.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-06-19
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) new SO_REUSEPORT_DETACH_BPF setsocktopt, from Martin.
2) BTF based map definition, from Andrii.
3) support bpf_map_lookup_elem for xskmap, from Jonathan.
4) bounded loops and scalar precision logic in the verifier, from Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Temporarily cache a casefolded version of the file name under lookup in
ext4_filename, to avoid repeatedly casefolding it. I got up to 30%
speedup on lookups of large directories (>100k entries), depending on
the length of the string under lookup.
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
- Couple of fixes to handle resource ranges and
requesting response always from firmware;
- Add processor control
- Add support APIs for DMA
- Fix the SPDX license plate
- Unused varible warning fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LAdf
-----END PGP SIGNATURE-----
Merge tag 'drivers_soc_for_5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into arm/drivers
SOC: TI SCI updates for v5.3
- Couple of fixes to handle resource ranges and
requesting response always from firmware;
- Add processor control
- Add support APIs for DMA
- Fix the SPDX license plate
- Unused varible warning fix
* tag 'drivers_soc_for_5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
firmware: ti_sci: Fix gcc unused-but-set-variable warning
firmware: ti_sci: Use the correct style for SPDX License Identifier
firmware: ti_sci: Parse all resource ranges even if some is not available
firmware: ti_sci: Add support for processor control
firmware: ti_sci: Add resource management APIs for ringacc, psi-l and udma
firmware: ti_sci: Always request response from firmware
Signed-off-by: Olof Johansson <olof@lixom.net>
If a filesystem uses keys to hold authentication tokens, then it needs a
token for each VFS operation that might perform an authentication check -
either by passing it to the server, or using to perform a check based on
authentication data cached locally.
For open files this isn't a problem, since the key should be cached in the
file struct since it represents the subject performing operations on that
file descriptor.
During pathwalk, however, there isn't anywhere to cache the key, except
perhaps in the nameidata struct - but that isn't exposed to the
filesystems. Further, a pathwalk can incur a lot of operations, calling
one or more of the following, for instance:
->lookup()
->permission()
->d_revalidate()
->d_automount()
->get_acl()
->getxattr()
on each dentry/inode it encounters - and each one may need to call
request_key(). And then, at the end of pathwalk, it will call the actual
operation:
->mkdir()
->mknod()
->getattr()
->open()
...
which may need to go and get the token again.
However, it is very likely that all of the operations on a single
dentry/inode - and quite possibly a sequence of them - will all want to use
the same authentication token, which suggests that caching it would be a
good idea.
To this end:
(1) Make it so that a positive result of request_key() and co. that didn't
require upcalling to userspace is cached temporarily in task_struct.
(2) The cache is 1 deep, so a new result displaces the old one.
(3) The key is released by exit and by notify-resume.
(4) The cache is cleared in a newly forked process.
Signed-off-by: David Howells <dhowells@redhat.com>
Provide a request_key_rcu() function that can be used to request a key
under RCU conditions. It can only search and check permissions; it cannot
allocate a new key, upcall or wait for an upcall to complete. It may
return a partially constructed key.
Signed-off-by: David Howells <dhowells@redhat.com>
Based on 1 normalized pattern(s):
this file is free software you can redistribute it and or modify it
under the terms of version 2 of the gnu general public license as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 8 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081207.443595178@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program if
not write to the free software foundation 51 franklin street fifth
floor boston ma 02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081207.308909165@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
