When direct I/O is used, the data buffer may not always align to page
boundaries. Introduce a page offset in transport data structures to
describe the location of the buffer within the page.
Also change the function to pass the page offset when sending data to
transport.
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The assignment dev = dev is redundant and should be removed.
Detected by CoverityScan, CID#1469486 ("Evaluation order violation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Nothing prevents I2C clients to access I2C while Tegra's driver is being
suspended, this results in -EBUSY error returned to the clients and that
may have unfortunate consequences. In particular this causes problems
for the TPS6586x MFD driver which emits hundreds of "failed to read
interrupt status" error messages on resume from suspend. This happens if
TPS6586X is used to wake system from suspend by the expired RTC alarm
timer because TPS6586X is an I2C device driver and its IRQ handler reads
the status register while Tegra's I2C driver is suspended, i.e. just after
kernel enabled IRQ's during of resume-from-suspend process.
Note that the removed tegra_i2c_resume() invoked tegra_i2c_init() which
performs HW reset. That seems was also not entirely correct because moving
tegra_i2c_resume to an earlier stage of resume-from-suspend process causes
I2C transfer to fail in the case of TPS6586X. It is fine to remove the
HW-reinitialization for now because it should be only needed in a case of
using lowest power-mode during suspend, which upstream kernel doesn't
support.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This time around we have mostly trivial changes. However, there are
also a couple of "real" patches improving a few aspects of the
demux-pinctrl behavior and we also actually reset pca954x chips on
probe when we have the ability to do so.
This fixes linker errors due to undefined symbols when one or more of
the TI DaVinci SoCs is not enabled in the kernel config.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20180525181150.17873-10-david@lechnology.com
On some davinci SoCs, we need to register the PSC clocks during early
boot because they are needed for clocksource/clockevent. These changes
allow for dev == NULL because in this case, we won't have a platform
device for the clocks.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20180525181150.17873-9-david@lechnology.com
PLL0 on davinci/da850-type device needs to be registered early in boot
because it is needed for clocksource/clockevent. Change the driver
to use CLK_OF_DECLARE for this special case.
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20180525181150.17873-8-david@lechnology.com
This modifies the TI Davinci PLL clock driver to allow for the case
when dev == NULL. On some (most) SoCs that use this driver, the PLL
clock needs to be registered during early boot because it is used
for clocksource/clkevent and there will be no platform device available.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20180525181150.17873-7-david@lechnology.com
Fix parent of EMAC and voice codec PSC clocks. Documentation is clear
on EMAC clock parent, but its not fully clear on parent of voice codec
clock. The implementation chosen is matches arch/arm/mach-davinci/dm365.c.
Add a comment explaining this for posterity.
There is only one power domain on DM365. Fix the power domain of voice
codec and vpss dac modules.
While at it, add a comment explaining how the parent of vpss dac clock was
derived. Note that this patch does not touch the parent of vpss dac clock.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20180525181150.17873-6-david@lechnology.com
PLL2 SYSCLK1 on DM646x is connected to DDR2 PHY and cannot
be disabled. Mark it so to prevent unused clock disable
infrastructure from disabling it.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20180525181150.17873-5-david@lechnology.com
The clkdev lookups for the ASP0/1 devices on TI DM355 were declared, but
not assigned to any LPSC. This assigns the clkdev lookups to the
correct LPSCs.
Reported-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20180525181150.17873-4-david@lechnology.com
This fixes the parent clock names of the SYSCLKn clocks for the DM355
SoC in the TI DaVinici PLL clock driver.
It appears that this name just didn't get updated to the correct name
like the other SoCs during the driver's development.
Reported-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20180525181150.17873-3-david@lechnology.com
This removes pll2_sysclk2 from the TI DM355 clock driver. This SoC
doesn't have such a clock. Also, SYSCLK_ALWAYS_ENABLED is transferred
to pll2_sysclk1 since it drives the DDR and doesn't have another
mechanism to keep it on.
Reported-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20180525181150.17873-2-david@lechnology.com
To enable XIP it is executed both normal and error cases.
This call can be moved after the for loop as same with erase chip.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Currently the functions use to check both chip ready and good.
But the chip ready is not enough to check the operation status.
So change this to check the chip good instead of this.
About the retry functions to make sure the error handling remain it.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
For the word write functions it is retried for error.
But it is not implemented to retry for the erase functions.
To make sure for the erase functions change to retry as same.
This is needed to prevent the flash erase error caused only once.
It was caused by the error case of chip_good() in the do_erase_oneblock().
Also it was confirmed on the MACRONIX flash device MX29GL512FHT2I-11G.
But the error issue behavior is not able to reproduce at this moment.
The flash controller is parallel Flash interface integrated on BCM53003.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The definition can be used for other program and erase operations also.
So change the naming to MAX_RETRIES from MAX_WORD_RETRIES.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
For the word write it is checked if the chip has the correct value.
But it is not checked for the write buffer as only checked if ready.
To make sure for the write buffer change to check the value.
It is enough as this patch is only checking the last written word.
Since it is described by data sheets to check the operation status.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
btrfs_truncate() uses two variables for error handling, ret and err (if
this sounds familiar, it's because btrfs_truncate_inode_items() did
something similar). This is error prone, as was made evident by "Btrfs:
fix error handling in btrfs_truncate()". We only have err because we
don't want to mask an error if we call btrfs_update_inode() and
btrfs_end_transaction(), so let's make that its own scoped return
variable and use ret everywhere else.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
ath.git patches for 4.18. Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
Driver switches vif sta_state into QTNF_STA_CONNECTING when cfg80211
core initiates connect procedure. Further this state is changed either
to QTNF_STA_CONNECTED or to QTNF_STA_DISCONNECTED by BSS_JOIN and
BSS_LEAVE events from firmware. However it is possible that no such
events will be sent by firmware, e.g. if EAPOL timed out.
In this case vif sta_mode will remain in QTNF_STA_CONNECTING state and
all subsequent connection attempts will fail with -EBUSY error code.
Fix this by perfroming STA state transition from QTNF_STA_CONNECTING
to QTNF_STA_DISCONNECTED in cfg80211 disconnect callback.
No need to rely upon firmware events in this case.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not process bg_scan_period parameter in qtnfmac driver.
Pass correct values as is. In the case of invalid values
pass default value. Leave further processing to firmware.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Free command skb if bus state is not QTNF_FW_STATE_ACTIVE.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Control path will not be operational after firmware failure. Change bus
state to QTNF_FW_STATE_EP_DEAD after the control path timeout.
Don't wait for timeout if control path is already dead.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver uses statically allocated wdev structures for each virtual
interface. However wdev structure is not properly cleaned up between
its uses. As a result, various bugs appear when userspace tools
like hostapd were not gracefully stopped.
In particular, this commit fixes the following issue:
- start hostapd with more than 2 mBSS
- kill hostapd using SIGKILL
- start again hostapd with more than 2 mBSS
However only two mBSS entities will be started: primary
and the last BSS listed in hostapd config.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce a function that will map an error code reported in reply
to a firmware command, into one of standard errno codes.
Use additional error codes to improve error reporting
for MAC address changes.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Shorten line lengths using a more compact notation to access mac info.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Functions qtnf_cmd_resp_parse and qtnf_cmd_resp_check have
been removed. Remove their declarations as well.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Some bugzilla fixes;
* Some kernel warning fixes;
* Fix for an (ETSI) WMM limits bug;
* Fix for a Bluetooth coexistence problem on 9000 devices;
* Fix for an interoperability bug related to block-ack sessions;
-----BEGIN PGP SIGNATURE-----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=oIAR
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2018-05-30' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Final batch of iwlwifi patches for 4.18
* Some bugzilla fixes;
* Some kernel warning fixes;
* Fix for an (ETSI) WMM limits bug;
* Fix for a Bluetooth coexistence problem on 9000 devices;
* Fix for an interoperability bug related to block-ack sessions;
Without CONFIG_MMU, we get a link error:
drivers/gpu/drm/v3d/v3d_bo.o: In function `v3d_gem_fault':
v3d_bo.c:(.text+0x3ca): undefined reference to `vm_insert_mixed'
The other drivers with this problem already depend on CONFIG_MMU,
so let's do the same thing here.
Fixes: 57692c94dc ("drm/v3d: Introduce a new DRM driver for Broadcom V3D V3.x+")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525155030.3667352-5-arnd@arndb.de
Move to_cros_ec_dev macro to cros_ec.h and use it when the private ec
object is needed from device object.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
In the perf.data HEADER_CPUDESC feadure header we store first the number
of available CPUs in the system, then the number of CPUs at the time of
writing the header, not the other way around.
Reported-by: Thomas-Mich Richter <tmricht@linux.ibm.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kim Phillips <kim.phillips@arm.com>
Cc: Lakshman Annadorai <lakshmana@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Simon Que <sque@chromium.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-j7o92acm2vnxjv70y4o3swoc@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
ARM CoreSight auxtrace uses 'sample->addr' to record the target address
for branch instructions, so the data of 'sample->addr' is required for
tracing data analysis.
This commit collects data of 'sample->addr' into perf sample dict,
finally can be used for python script for parsing event.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Walker <robert.walker@arm.com>
Cc: Tor Jeremiassen <tor@ti.com>
Cc: coresight@lists.linaro.org
Cc: kim.phillips@arm.co
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-doc@vger.kernel.org
Link: http://lkml.kernel.org/r/1527497103-3593-3-git-send-email-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add an explanation of each cpu's core and socket identifier to the
perf.data file format documentation.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20180528074433.16652-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The tail of a queue is supposed to be pointing to the next available
slot in a queue. In this implementation the tail is incremented before
it is used and as such points to the last used element, something that
has the immense advantage of centralizing tail management at a single
location and eliminating a lot of redundant code.
But this needs to be taken into consideration on the dequeueing side
where the head also needs to be incremented before it is used, or the
first available element of the queue will be skipped.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Walker <robert.walker@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1527289854-10755-1-git-send-email-mathieu.poirier@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
bpf_object__open()/bpf_object__open_buffer can return error pointer or
NULL, check the return values with IS_ERR_OR_NULL() in bpf__prepare_load
and bpf__prepare_load_buffer
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: netdev@vger.kernel.org
Link: https://lkml.kernel.org/n/tip-psf4xwc09n62al2cb9s33v9h@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The dw_hdmi_setup_rx_sense exported function should not use struct device
to recover the dw-hdmi context using drvdata, but take struct dw_hdmi
directly like other exported functions.
This caused a regression using Meson DRM on S905X since v4.17-rc1 :
Internal error: Oops: 96000007 [#1] PREEMPT SMP
[...]
CPU: 0 PID: 124 Comm: irq/32-dw_hdmi_ Not tainted 4.17.0-rc7 #2
Hardware name: Libre Technology CC (DT)
[...]
pc : osq_lock+0x54/0x188
lr : __mutex_lock.isra.0+0x74/0x530
[...]
Process irq/32-dw_hdmi_ (pid: 124, stack limit = 0x00000000adf418cb)
Call trace:
osq_lock+0x54/0x188
__mutex_lock_slowpath+0x10/0x18
mutex_lock+0x30/0x38
__dw_hdmi_setup_rx_sense+0x28/0x98
dw_hdmi_setup_rx_sense+0x10/0x18
dw_hdmi_top_thread_irq+0x2c/0x50
irq_thread_fn+0x28/0x68
irq_thread+0x10c/0x1a0
kthread+0x128/0x130
ret_from_fork+0x10/0x18
Code: 34000964 d00050a2 51000484 9135c042 (f864d844)
---[ end trace 945641e1fbbc07da ]---
note: irq/32-dw_hdmi_[124] exited with preempt_count 1
genirq: exiting task "irq/32-dw_hdmi_" (124) is an active IRQ thread (irq 32)
Fixes: eea034af90 ("drm/bridge/synopsys: dw-hdmi: don't clobber drvdata")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1527673438-20643-1-git-send-email-narmstrong@baylibre.com
Fixes a crash on asics without powerplay yet (e.g., vega20).
Reviewed-by: Rex Zhu<rezhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Get rid of an empty dublicate of smu10_display_clock_voltage_request
Add display_clock_voltage_request to smu10 functions struct so it
can be called from outside the class and connect the pointer to
the function.
That way Display driver can finally apply clock voltage requests
when needed.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The AMD_CG_SUPPORT_HDP_LS was wrongly written as
AMD_CG_SUPPORT_BIF_LS.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The .syspll_id and .dfsdid are not initialzed correctly. And
le32_to_cpu transfer is needed on the output.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In per-vm-bo case, there could be no bo list.
But gds bo created from user space must be passed to bo list.
So adding a check to prevent to creat gds bo as per-vm-bo.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As now enabled per vm bo feature, the user mode driver won't supply the
bo_list generally, for this case, the gdb_base, gds_size, gws_base, gws_size and
oa_base, oa_size won't be set.
v2: fix warning (Chunming)
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We already check for started commands in all callbacks, but we should
also protect against already completed commands. Do this by taking
the checks to common code.
Acked-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
