Fix the following warnings:
drivers/media/usb/cx231xx/cx231xx-cards.c: In function 'read_eeprom':
drivers/media/usb/cx231xx/cx231xx-cards.c:979:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for:
[2040:b130] Hauppauge WinTV 930C-HD (model 1113xx)
After loading the driver the first open to dvb device node fails.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is needed to support PCTV QuatroStick 522e which uses a si2157.
The si2157 driver is written using i2c_client attachment.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Tested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The same card entry is used for HVR-4400 and HVR-5500.
Only HVR-5500 has been tested.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DVB-T was tested with 8MHz BW channels in germany
This driver is the simplest possible, it uses automatic mode for all
parameters (TPS).
Added spectrum inversion support.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Tested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We don't have license to redistribute this firmware, so extract
it from the driver, and add the needed headers.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Tested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using some random value, return an error if the
PCB config is not available or doesn't match a know profile
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That makes easier to understand the code. It would also help
to add support for having boards with just digital support
on some latter patch, as allowed by some PCB configs.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The initialization is already too complex. Use devm_ functions
to make the code simpler and easier to modify.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On some newer boards, like HVR-930C HD, the information at
the PCB tables are sometimes higher than the ones actually
available on the device. That causes the probing code to
go past the interfaces array.
Add checks to the interface number before going past the
array.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The s->clk never gets setup in sc16is7xx_probe() and instead was using a
local clk variable, but then testing the uninitialized s->clk during
teardown
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the warning generated by sparse: "Using plain integer as NULL pointer" by replacing the offending 0s with NULL.
drivers/staging/lustre/lustre/lov/lov_obd.c:902:48: warning: Using plain integer as NULL pointer
drivers/staging/lustre/lustre/lov/lov_obd.c:946:54: warning: Using plain integer as NULL pointer
drivers/staging/lustre/lustre/lov/lov_obd.c:2819:46: warning: Using plain integer as NULL pointer
Signed-off-by: Marc Fite <marc@fite.cat>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed redundant comments from desc.h header file.
Signed-off-by: Igor Bezukh <igbzkh@gmail.com>
C99 style comments will be fixed in further patches.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For PCI boards, the `auto_attach` handler, `pc236_auto_attach()`,
initializes `dev->board_ptr` to point to a `struct pc236_board`, but
leaves `dev->board_name` unchanged. The Comedi core will have
initialized `dev->board_name` to the `driver_name` string member of
`amplc_pc236_driver`. For consistency with ISA boards manually
configured by the `COMEDI_DEVCONFIG` ioctl via the legacy `attach`
handler, `pc236_attach()`, set `dev->board_name` to the `name` member of
the `struct pc236_board` pointed to by `dev->board_ptr`.
Both `pc236_attach()` and `pc236_auto_attach()` call
`pc236_common_attach()`, which also sets `dev->board_name` to the `name`
member of the `struct pc236_board`. Since this assignment no longer
changes anything, remove it.
A nice side-effect of this change is that the same owner name string is
used for requesting I/O regions (before the call the
`pc236_common_attach()`) as is used for requesting the IRQ handler
(during the call to `pc236_common_attach()`). It was already the same
for (manually configured) ISA boards, but is now the same for
(automatically configured) PCI boards.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `PCI_DEVICE_ID_AMPLICON_PCI236` macro is only used once, in the
module device table, so remove it and expand the macro in the table.
`The `PCI_DEVICE_ID_INVALID` macro is no longer used, so remove it.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since only a single PCI board is supported by the driver, there is no
need to call `pc236_find_pci_board()` to find the a board entry with
matching PCI device ID in `pc236_pci_boards[]`. Just point to the entry
directly and remove the look-up function. In fact, there is no reason
for `pc236_pci_boards[]` to be an array, so change it to a non-array
variable and rename it to `pc236_pci_board`. Also, the `devid` member
of `struct pc236_board` is no longer needed as it was only used by the
look-up function, so remove it.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the legacy attach routine `pc236_attach()` is only called for
board names matching an entry in our array of ISA boards
`pc236_isa_boards[]`, and it is reasonable to expect all elements of
`pc236_isa_boards[]` to have their `bustype` member initialized
correctly to `isa_bustype`, don't bother checking the bus type in
`pc236_attach()`. Add `if (!DO_ISA) return -EINVAL` to optimize out the
remainder of the function if `CONFIG_COMEDI_AMPLC_PC236_ISA` is not
defined.
Similarly, don't bother checking the bus type in
`pc236_find_pci_board()` as it is reasonable to expect all elements of
`pc236_pci_boards[]` to have their `bustype` member initialized
correctly to `pci_bustype`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split `pc236_boards[]` into `pc236_isa_boards[]` for ISA cards and
`pc236_pci_boards[]` for PCI cards (there is only one of each). Only
initialize the board name look-up members of `struct comedi_driver
amplc_pc236_driver` if the ISA part of the driver is enabled in the
kernel config (`CONFIG_COMEDI_AMPLC_PC236_ISA`) using the array of ISA
boards (`pc236_isa_boards[]`). The driver doesn't allow manual
configuration of PCI devices, so there is no point having the comedi
core match the names of the PCI boards before it calls our driver's
legacy attach routine (`pc236_attach()`).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `model` member of `struct pc236_board` is no longer used since the
code to remove manual configuration of PCI devices was removed. Get rid
of it.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Absorb `pc236_pci_common_attach()` into `pc236_auto_attach()` since
that's the only place it is called from.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call to `comedi_set_hw_dev()` from `pc236_pci_common_attach()` is
now unnecessary since `pc236_pci_common_attach()` is now only called
from this driver's `auto_attach` hook `pc236_auto_attach()` and the
comedi core now calls `comedi_set_hw_dev()` before calling that. Remove
the unnecessary call.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that this driver no longer supports "manual" attachment of PCI
devices in its `attach` hook (`pc236_attach()`), it no longer has code
that searches for a suitable PCI device and increments its reference
count. Since the driver no longer has any reason for incrementing and
decrementing the PCI device's reference count, the calls to
`pci_dev_get()` and `pci_dev_put()` can be removed.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the code that allows PCI boards to be manually attached by the
`COMEDI_DEVCONFIG` ioctl (or the "comedi_config" application).
Supported PCI boards (PCI236) will be attached automatically at probe
time via `comedi_pci_auto_config()` and the `auto_attach` hook in the
`struct comedi_driver`.
The "wildcard" entry in `pc236_boards[]` was only used when manually
attaching a PCI board using a driver name instead of a board name, so is
no longer needed. Remove it.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
