Change interrupt trigger from IRQ_TYPE_LEVEL_HIGH to IRQ_TYPE_EDGE_RISING
for stable NFC I2C interrupt handling.
Samsung's NFC Firmware sends an i2c frame as below.
1. NFC Firmware sets the GPIO(interrupt pin) high when there is an i2c
frame to send.
2. If the CPU's I2C master has received the i2c frame, NFC F/W sets the
GPIO low.
NFC driver's i2c interrupt handler would be called in the abnormal case
as the NFC FW task of number 2 is delayed because of other high priority
tasks.
In that case, NFC driver will try to receive the i2c frame but there isn't
any i2c frame to send in NFC.
It would cause an I2C communication problem. This case would hardly happen.
But, I changed the interrupt as a defense code.
If Driver uses the TRIGGER_RISING instead of the LEVEL trigger,
there would be no problem even if the NFC FW task is delayed.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add documentation for SAMA7G5 gigabit ethernet interface.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add documentation for SAMA7G5 ethernet interface.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfyTQyAAoJEG4XJFUm622bCdcIAIyVnqdW7pnoDmWIyQmAEnD9
vGARkzghPHXnufpOzohyDdxT12X9klhrxSVIgzEgH1/pl3i1PpnF6KXyGFCC44Lw
wrLXhQygPzmIW1IZtJJE3G72WExXoRjWx6LD1I7C7oEIduqFixXADmK2tKzFp795
Jxum+sOeT6+Dk1OvO/fIroBHX73mRE9zAuiTIMpt2G1j8uXs9QVfcTbTrUshLASN
0sX9J6JutltBuM4G7+bFpVzKnLnlQ7ebUaF6nvTCQsgHWZwkS7yAubSWX9sFohbR
UXgQHNE83s/esOg7nBxAfqTKP8mbxsobmxZtxE5GR5vFY5FJDxqP9Zc2KzPp39w=
=CbX/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.11
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
* tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (180 commits)
wl1251: remove trailing semicolon in macro definition
airo: remove trailing semicolon in macro definition
wilc1000: added queue support for WMM
wilc1000: call complete() for failure in wilc_wlan_txq_add_cfg_pkt()
wilc1000: free resource in wilc_wlan_txq_add_mgmt_pkt() for failure path
wilc1000: free resource in wilc_wlan_txq_add_net_pkt() for failure path
wilc1000: added 'ndo_set_mac_address' callback support
brcmfmac: expose firmware config files through modinfo
wlcore: Switch to using the new API kobj_to_dev()
rtw88: coex: add feature to enhance HID coexistence performance
rtw88: coex: upgrade coexistence A2DP mechanism
rtw88: coex: add action for coexistence in hardware initial
rtw88: coex: add function to avoid cck lock
rtw88: coex: change the coexistence mechanism for WLAN connected
rtw88: coex: change the coexistence mechanism for HID
rtw88: coex: update AFH information while in free-run mode
rtw88: coex: update the mechanism for A2DP + PAN
rtw88: coex: add debug message
rtw88: coex: run coexistence when WLAN entering/leaving LPS
Revert "rtl8xxxu: Add Buffalo WI-U3-866D to list of supported devices"
...
====================
Link: https://lore.kernel.org/r/20201203185732.9CFA5C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since S3FWRN82 NFC Chip, The UART interface can be used.
S3FWRN82 supports I2C and UART interface.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are other NXP NCI compatible NFC controllers such as the PN7150
that use an integrated firmware and therefore do not have a GPIO to
select firmware downloading mode. To support this kind of controller,
let's make the firmware GPIO optional.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201201113921.6572-1-frieder.schrempf@kontron.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH
Fixes: a1a8b4594f ("NFC: pn544: i2c: Add DTS Documentation")
Fixes: 6be88670fc ("NFC: nxp-nci_i2c: Add I2C support to NXP NCI driver")
Fixes: e3b3292215 ("dt-bindings: can: tcan4x5x: Update binding to use interrupt property")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for tcan4x5x.txt
Link: https://lore.kernel.org/r/20201026153620.89268-1-krzk@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
HDMI, unsupported modes, and vblank timeouts, a fix for ast to reload
the gamma LUT after changing the plane format and a double-free fix for
nouveau
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCX79tPAAKCRDj7w1vZxhR
xdp6AP0Txa4ssBQzkXzPwxeoHIO4KvRNVG4N/s73UEfVr5ovFAEAlEyL4ku0BOlb
Lyk9MdmhSMl/YRuWzqHK/N1wBk6M5Qk=
=7635
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2020-11-26' of ssh://git.freedesktop.org/git/drm/drm-misc into drm-fixes
A bunch of fixes for vc4 fixing some coexistence issue between wifi and
HDMI, unsupported modes, and vblank timeouts, a fix for ast to reload
the gamma LUT after changing the plane format and a double-free fix for
nouveau
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201126085450.r3i7wvj7pizsa4l6@gilmour
Convert the bindings document for Microchip KSZ Series Ethernet switches
from txt to yaml. Removed spi-cpha and spi-cpol flags is this should be
handled by the device driver.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A collection of small fixes: the only core change is a minor error
code handling in the control API, and all the rest are device-specific
fixes, mostly quirks, fixups and ASoC Intel fixes.
It looks boring, and good so.
-----BEGIN PGP SIGNATURE-----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=E7Lw
-----END PGP SIGNATURE-----
Merge tag 'sound-5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes: the only core change is a minor error
code handling in the control API, and all the rest are device-specific
fixes, mostly quirks, fixups and ASoC Intel fixes.
It looks boring, and good so"
* tag 'sound-5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: mixart: Fix mutex deadlock
ALSA: hda/ca0132: Fix compile warning without PCI
ASOC: Intel: kbl_rt5663_rt5514_max98927: Do not try to disable disabled clock
ALSA: usb-audio: Add delay quirk for all Logitech USB devices
ASoC: Intel: catpt: Correct clock selection for dai trigger
ASoC: Intel: catpt: Skip position update for unprepared streams
ASoC: qcom: lpass-platform: Fix memory leak
ASoC: Intel: KMB: Fix S24_LE configuration
ALSA: hda: Add Alderlake-S PCI ID and HDMI codec vid
ALSA: usb-audio: Use ALC1220-VB-DT mapping for ASUS ROG Strix TRX40 mobo
ALSA: firewire: Clean up a locking issue in copy_resp_to_buf()
ASoC: rt1015: increase the time to detect BCLK
ALSA: ctl: fix error path at adding user-defined element set
ALSA: hda/realtek - HP Headset Mic can't detect after boot
ALSA: hda/realtek - Add supported mute Led for HP
ALSA: hda/realtek: Add some Clove SSID in the ALC293(ALC1220)
ALSA: hda/realtek - Add supported for Lenovo ThinkPad Headset Button
ASoC: rt1015: add delay to fix pop noise from speaker
Correct fsl,clk-source example since flexcan driver uses "of_property_read_u8"
to get this property.
Fixes: 9d73399277 ("dt-bindings: can: flexcan: add PE clock source property to device tree")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20201106105627.31061-2-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the missing reference to the clock-frequency property. The
driver uses a of_property_read_u32() to read the property to mark it as uint32.
Fixes: e5ab9aa7e4 ("dt-bindings: can: flexcan: convert fsl,*flexcan bindings to yaml")
Link: https://lore.kernel.org/r/20201119073357.2858925-1-mkl@pengutronix.de
Cc: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: Oleksij Rempel <ore@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The RaspberryPi4 has both a WiFi chip and HDMI outputs capable of doing
4k. Unfortunately, the 1440p resolution at 60Hz has a TMDS rate on the
HDMI cable right in the middle of the first Wifi channel.
Add a property to our HDMI controller, that could be reused by other
similar HDMI controllers, to allow the OS to take whatever measure is
necessary to avoid that crosstalk.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029134018.1948636-1-maxime@cerno.tech
Since commit:
0e030a373d ("can: flexcan: fix endianess detection")
the fsl,imx53-flexcan isn't compatible with the fsl,p1010-flexcan any more. As
the former accesses the IP core in Little Endian mode and the latter uses Big
Endian mode.
With the conversion of the flexcan DT bindings to yaml, the dt_binding_check
this throws the following error:
Documentation/devicetree/bindings/clock/imx5-clock.example.dt.yaml: can@53fc8000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx53-flexcan', 'fsl,p1010-flexcan'] is too long
Additional items are not allowed ('fsl,p1010-flexcan' was unexpected)
'fsl,imx53-flexcan' is not one of ['fsl,imx7d-flexcan', 'fsl,imx6ul-flexcan', 'fsl,imx6sx-flexcan']
'fsl,imx53-flexcan' is not one of ['fsl,ls1028ar1-flexcan']
'fsl,imx6q-flexcan' was expected
'fsl,lx2160ar1-flexcan' was expected
From schema: /builds/robherring/linux-dt-bindings/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml
The error is fixed by replacing the "fsl,p1010-flexcan" compatible
(which turned out the be incompatible) with "fsl,imx25-flexcan" in the
binding example.
Reported-by: Rob Herring <robh+dt@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20201111213548.1621094-1-mkl@pengutronix.de
[robh: Add "fsl,imx25-flexcan" as fallback]
Signed-off-by: Rob Herring <robh@kernel.org>
As both the i.MX35 and i.MX53 flexcan IP cores are compatible to the i.MX25,
they are listed as:
compatible = "fsl,imx35-flexcan", "fsl,imx25-flexcan";
and:
compatible = "fsl,imx53-flexcan", "fsl,imx25-flexcan";
in the SoC device trees.
This patch fixes the following errors, which shows up during a dtbs_check:
arch/arm/boot/dts/imx53-ard.dt.yaml: can@53fc8000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx53-flexcan', 'fsl,imx25-flexcan'] is too long
Additional items are not allowed ('fsl,imx25-flexcan' was unexpected)
'fsl,imx53-flexcan' is not one of ['fsl,imx7d-flexcan', 'fsl,imx6ul-flexcan', 'fsl,imx6sx-flexcan']
'fsl,imx53-flexcan' is not one of ['fsl,ls1028ar1-flexcan']
'fsl,imx6q-flexcan' was expected
'fsl,lx2160ar1-flexcan' was expected
From schema: Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml
Fixes: e5ab9aa7e4 ("dt-bindings: can: flexcan: convert fsl,*flexcan bindings to yaml")
Reported-by: Rob Herring <robh+dt@kernel.org>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20201111130507.1560881-4-mkl@pengutronix.de
[robh: drop singular fsl,imx53-flexcan and fsl,imx35-flexcan]
Signed-off-by: Rob Herring <robh@kernel.org>
The fsl,stop-mode property is a phandle-array and should consist of one phandle
and two 32 bit integers, e.g.:
fsl,stop-mode = <&gpr 0x34 28>;
This patch fixes the following errors, which shows up during a dtbs_check:
arch/arm/boot/dts/imx6dl-apf6dev.dt.yaml: can@2090000: fsl,stop-mode: [[1, 52, 28]] is too short
From schema: Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml
Fixes: e5ab9aa7e4 ("dt-bindings: can: flexcan: convert fsl,*flexcan bindings to yaml")
Reported-by: Rob Herring <robh+dt@kernel.org>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20201111130507.1560881-5-mkl@pengutronix.de
Signed-off-by: Rob Herring <robh@kernel.org>
- Fix the fallout of the IPI as interrupt conversion in Kconfig and the
BCM2836 interrupt chip driver/
- Fixes for interrupt affinity setting and the handling of hierarchical
irq domains in the SiFive PLIC driver.
- Make the unmapped event handling in the TI SCI driver work correctly.
- A few minor fixes and cleanups in various chip drivers and Kconfig.
-----BEGIN PGP SIGNATURE-----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=HUPi
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2020-11-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes for interrupt chip drivers:
- Fix the fallout of the IPI as interrupt conversion in Kconfig and
the BCM2836 interrupt chip driver
- Fixes for interrupt affinity setting and the handling of
hierarchical irq domains in the SiFive PLIC driver
- Make the unmapped event handling in the TI SCI driver work
correctly
- A few minor fixes and cleanups in various chip drivers and Kconfig"
* tag 'irq-urgent-2020-11-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dt-bindings: irqchip: ti, sci-inta: Fix diagram indentation for unmapped events
irqchip/ti-sci-inta: Add support for unmapped event handling
dt-bindings: irqchip: ti, sci-inta: Update for unmapped event handling
irqchip/renesas-intc-irqpin: Merge irlm_bit and needs_irlm
irqchip/sifive-plic: Fix chip_data access within a hierarchy
irqchip/sifive-plic: Fix broken irq_set_affinity() callback
irqchip/stm32-exti: Add all LP timer exti direct events support
irqchip/bcm2836: Fix missing __init annotation
irqchip/mips: Drop selection of IRQ_DOMAIN_HIERARCHY
irqchip/mst: Make mst_intc_of_init static
irqchip/mst: MST_IRQ should depend on ARCH_MEDIATEK or ARCH_MSTARV7
genirq: Let GENERIC_IRQ_IPI select IRQ_DOMAIN_HIERARCHY
The bus + qmi-chip-id + qmi-board-id is not enough to identify the correct
board data file on IPQ6018 based devices. Multiple different boards share
the same values. Only the original reference designs can currently be
identified and loaded from the board-2.bin. But these will not result in
the correct calibration data when combined with the pre-calibration data
from the device.
An additional "variant" information has to be provided to select the
correct board data for a design which was modified by an ODM. This follows
the same approach as ath10k.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015131501.1939685-1-sven@narfation.org
and netfilter subtrees.
Current release - bugs in new features:
- can: isotp: isotp_rcv_cf(): enable RX timeout handling in
listen-only mode
Previous release - regressions:
- mac80211:
- don't require VHT elements for HE on 2.4 GHz
- fix regression where EAPOL frames were sent in plaintext
- netfilter:
- ipset: Update byte and packet counters regardless of whether
they match
- ip_tunnel: fix over-mtu packet send by allowing fragmenting even
if inner packet has IP_DF (don't fragment) set in its header
(when TUNNEL_DONT_FRAGMENT flag is not set on the tunnel dev)
- net: fec: fix MDIO probing for some FEC hardware blocks
- ip6_tunnel: set inner ipproto before ip6_tnl_encap to un-break
gso support
- sctp: Fix COMM_LOST/CANT_STR_ASSOC err reporting on big-endian
platforms, sparse-related fix used the wrong integer size
Previous release - always broken:
- netfilter: use actual socket sk rather than skb sk when routing
harder
- r8169: work around short packet hw bug on RTL8125 by padding frames
- net: ethernet: ti: cpsw: disable PTPv1 hw timestamping
advertisement, the hardware does not support it
- chelsio/chtls: fix always leaking ctrl_skb and another leak caused
by a race condition
- fix drivers incorrectly writing into skbs on TX:
- cadence: force nonlinear buffers to be cloned
- gianfar: Account for Tx PTP timestamp in the skb headroom
- gianfar: Replace skb_realloc_headroom with skb_cow_head for PTP
- can: flexcan:
- remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
- add ECC initialization for VF610 and LX2160A
- flexcan_remove(): disable wakeup completely
- can: fix packet echo functionality:
- peak_canfd: fix echo management when loopback is on
- make sure skbs are not freed in IRQ context in case they need
to be dropped
- always clone the skbs to make sure they have a reference on
the socket, and prevent it from disappearing
- fix real payload length return value for RTR frames
- can: j1939: return failure on bind if netdev is down, rather than
waiting indefinitely
Misc:
- IPv6: reply ICMP error if the first fragment don't include all
headers to improve compliance with RFC 8200
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=5R2w
-----END PGP SIGNATURE-----
Merge tag 'net-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.10-rc3, including fixes from wireless, can, and
netfilter subtrees.
Current merge window - bugs in new features:
- can: isotp: isotp_rcv_cf(): enable RX timeout handling in
listen-only mode
Previous releases - regressions:
- mac80211:
- don't require VHT elements for HE on 2.4 GHz
- fix regression where EAPOL frames were sent in plaintext
- netfilter:
- ipset: Update byte and packet counters regardless of whether
they match
- ip_tunnel: fix over-mtu packet send by allowing fragmenting even if
inner packet has IP_DF (don't fragment) set in its header (when
TUNNEL_DONT_FRAGMENT flag is not set on the tunnel dev)
- net: fec: fix MDIO probing for some FEC hardware blocks
- ip6_tunnel: set inner ipproto before ip6_tnl_encap to un-break gso
support
- sctp: Fix COMM_LOST/CANT_STR_ASSOC err reporting on big-endian
platforms, sparse-related fix used the wrong integer size
Previous releases - always broken:
- netfilter: use actual socket sk rather than skb sk when routing
harder
- r8169: work around short packet hw bug on RTL8125 by padding frames
- net: ethernet: ti: cpsw: disable PTPv1 hw timestamping
advertisement, the hardware does not support it
- chelsio/chtls: fix always leaking ctrl_skb and another leak caused
by a race condition
- fix drivers incorrectly writing into skbs on TX:
- cadence: force nonlinear buffers to be cloned
- gianfar: Account for Tx PTP timestamp in the skb headroom
- gianfar: Replace skb_realloc_headroom with skb_cow_head for PTP
- can: flexcan:
- remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
- add ECC initialization for VF610 and LX2160A
- flexcan_remove(): disable wakeup completely
- can: fix packet echo functionality:
- peak_canfd: fix echo management when loopback is on
- make sure skbs are not freed in IRQ context in case they need to
be dropped
- always clone the skbs to make sure they have a reference on the
socket, and prevent it from disappearing
- fix real payload length return value for RTR frames
- can: j1939: return failure on bind if netdev is down, rather than
waiting indefinitely
Misc:
- IPv6: reply ICMP error if the first fragment don't include all
headers to improve compliance with RFC 8200"
* tag 'net-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
ionic: check port ptr before use
r8169: work around short packet hw bug on RTL8125
net: openvswitch: silence suspicious RCU usage warning
chelsio/chtls: fix always leaking ctrl_skb
chelsio/chtls: fix memory leaks caused by a race
can: flexcan: flexcan_remove(): disable wakeup completely
can: flexcan: add ECC initialization for VF610
can: flexcan: add ECC initialization for LX2160A
can: flexcan: remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
can: mcp251xfd: remove unneeded break
can: mcp251xfd: mcp251xfd_regmap_nocrc_read(): fix semicolon.cocci warnings
can: mcp251xfd: mcp251xfd_regmap_crc_read(): increase severity of CRC read error messages
can: peak_canfd: pucan_handle_can_rx(): fix echo management when loopback is on
can: peak_usb: peak_usb_get_ts_time(): fix timestamp wrapping
can: peak_usb: add range checking in decode operations
can: xilinx_can: handle failure cases of pm_runtime_get_sync
can: ti_hecc: ti_hecc_probe(): add missed clk_disable_unprepare() in error path
can: isotp: padlen(): make const array static, makes object smaller
can: isotp: isotp_rcv_cf(): enable RX timeout handling in listen-only mode
can: isotp: Explain PDU in CAN_ISOTP help text
...
Hirschmann is building devices for automation and networking. Add them to the
vendor prefixes.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add delay to fix pop noise from speaker.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201105030804.31115-1-jack.yu@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to automate the verification of DT nodes convert
fsl-flexcan.txt to fsl,flexcan.yaml
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201022075218.11880-3-o.rempel@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For now we have only node name as common rule for all CAN controllers
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201022075218.11880-2-o.rempel@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
number of warnings from the once-noisy docs build process is nearly zero.
Getting to this point has required a lot of work; once there, hopefully we
can keep things that way.
I have packaged this as a separate pull because it does a fair amount of
reaching outside of Documentation/. The changes are all in comments and in
code placement. It's all been in linux-next since last week.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl+hscQPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YgZAH/0JeDA/1VLZYYTmdABz8mjBZsoW9tyPGGztF
nsh5ykdHhL3MeTRwumW5armLVrfKhd1XT+nIzD7OcWlqu+RDOvQ5I95rahr473hP
1SHTjqm3/AlJwQoeS72X5U6QEJQ58e2IwCbP23H3x7I3Q3snEA/HhswzxurfoB/Z
j81YzDV2YPEc0LJWZ5Vn0NEdwP8cdpFv5rojsQmepq7K0yJ7tEHb7/u2cEuUBgXS
8LcYCNPLpiN+q5N8uQ5oDjIUNdLQvP03kgKtQWiCTr4BRydOrDlJie28LIedamEz
anu7UfaVK4bxn+ugRI0g2+aWQKux81ULCinKUWmLRNbcxjhaQqQ=
=hDfp
-----END PGP SIGNATURE-----
Merge tag 'docs-5.10-warnings' of git://git.lwn.net/linux
Pull documentation build warning fixes from Jonathan Corbet:
"This contains a series of warning fixes from Mauro; once applied, the
number of warnings from the once-noisy docs build process is nearly
zero.
Getting to this point has required a lot of work; once there,
hopefully we can keep things that way.
I have packaged this as a separate pull because it does a fair amount
of reaching outside of Documentation/. The changes are all in comments
and in code placement. It's all been in linux-next since last week"
* tag 'docs-5.10-warnings' of git://git.lwn.net/linux: (24 commits)
docs: SafeSetID: fix a warning
amdgpu: fix a few kernel-doc markup issues
selftests: kselftest_harness.h: fix kernel-doc markups
drm: amdgpu_dm: fix a typo
gpu: docs: amdgpu.rst: get rid of wrong kernel-doc markups
drm: amdgpu: kernel-doc: update some adev parameters
docs: fs: api-summary.rst: get rid of kernel-doc include
IB/srpt: docs: add a description for cq_size member
locking/refcount: move kernel-doc markups to the proper place
docs: lockdep-design: fix some warning issues
MAINTAINERS: fix broken doc refs due to yaml conversion
ice: docs fix a devlink info that broke a table
crypto: sun8x-ce*: update entries to its documentation
net: phy: remove kernel-doc duplication
mm: pagemap.h: fix two kernel-doc markups
blk-mq: docs: add kernel-doc description for a new struct member
docs: userspace-api: add iommu.rst to the index file
docs: hwmon: mp2975.rst: address some html build warnings
docs: net: statistics.rst: remove a duplicated kernel-doc
docs: kasan.rst: add two missing blank lines
...
One space has been missing by the diagram update.
Fixes: bb2bd7c7f3 ("dt-bindings: irqchip: ti, sci-inta: Update for unmapped event handling")
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201103135004.2363-1-peter.ujfalusi@ti.com
Add the phy-handle and MDIO description and add the example with
PHY and MDIO nodes.
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The new DMA architecture introduced with AM64 introduced new event types:
unampped events.
These events are mapped within INTA in contrast to other K3 devices where
the events with similar function was originating from the UDMAP or ringacc.
The ti,unmapped-event-sources should contain phandle array to the devices
in the system (typically DMA controllers) from where the unmapped events
originate.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201020073243.19255-2-peter.ujfalusi@ti.com
This is a fairly large set of bug fixes on top of -rc1,
as most of them were ready but didn't quite make it into
the last-minute pull requests for the merge window.
Allwinner:
Fix for incorrect CPU overtemperature limit
Amlogic:
Multiple smaller DT bugfixes, and missing device nodes
Marvell EBU:
Add missing aliases for ethernet switch ports on
espressobin board
Marvell MMP:
One DTC warning fix
one bugfix for camera interface power-down
NXP i.MX:
Re-enable the GPIO driver on all defconfigs
ST STM32MP1:
Fix random crashes from incorrect voltage settings
Synaptics Berlin:
Enable the correct hardware timer driver
Texas Instruments K2G:
fix a boot regression in the power domain code
TEE drivers:
Fix regression in TEE "login" method
SCMI drivers:
multiple code fixes for corner cases in newly added code
MAINTAINERS file:
Move Kukjin Kim and Sangbeom Kim used to work on
Samsung Exynos.
Masahiro Yamada is stepping down as Uniphier maintainer
I did not include a series of patches that work around a
regression caused by a bugfix in an ethernet phy driver
that resulted in an inadvertent DT binding change. This is
still under discussion.
-----BEGIN PGP SIGNATURE-----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=cKNJ
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a fairly large set of bug fixes on top of -rc1, as most of
them were ready but didn't quite make it into the last-minute pull
requests for the merge window.
Allwinner:
- fix for incorrect CPU overtemperature limit
Amlogic:
- multiple smaller DT bugfixes, and missing device nodes
Marvell EBU:
- add missing aliases for ethernet switch ports on espressobin board
Marvell MMP:
- DTC warning fix
- bugfix for camera interface power-down
NXP i.MX:
- re-enable the GPIO driver on all defconfigs
ST STM32MP1:
- fix random crashes from incorrect voltage settings
Synaptics Berlin:
- enable the correct hardware timer driver
Texas Instruments K2G:
- fix a boot regression in the power domain code
TEE drivers:
- fix regression in TEE "login" method
SCMI drivers:
- multiple code fixes for corner cases in newly added code
MAINTAINERS file:
- move Kukjin Kim and Sangbeom Kim to credits (used to work on
Samsung Exynos)
- Masahiro Yamada is stepping down as Uniphier maintainer
I did not include a series of patches that work around a regression
caused by a bugfix in an ethernet phy driver that resulted in an
inadvertent DT binding change. This is still under discussion"
* tag 'arm-soc-fixes-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
soc: ti: ti_sci_pm_domains: check for proper args count in xlate
ARM: dts: stm32: Describe Vin power supply on stm32mp157c-edx board
ARM: dts: stm32: Describe Vin power supply on stm32mp15xx-dkx board
ARM: multi_v5_defconfig: Select CONFIG_GPIO_MXC
ARM: imx_v4_v5_defconfig: Select CONFIG_GPIO_MXC
ARM: dts: mmp2-olpc-xo-1-75: Use plural form of "-gpios"
ARM: dts: mmp3: Add power domain for the camera
arm64: berlin: Select DW_APB_TIMER_OF
dt-bindings: sram: sunxi-sram: add V3s compatible string
MAINTAINERS: Move Sangbeom Kim to credits
MAINTAINERS: Move Kukjin Kim to credits
MAINTAINERS: step down as maintainer of UniPhier SoCs and Denali driver
ARM: multi_v7_defconfig: Build in CONFIG_GPIO_MXC by default
ARM: imx_v6_v7_defconfig: Build in CONFIG_GPIO_MXC by default
arm64: defconfig: Build in CONFIG_GPIO_MXC by default
arm64: dts: meson: odroid-n2 plus: fix vddcpu_a pwm
ARM: dts: meson8: remove two invalid interrupt lines from the GPU node
arm64: dts: amlogic: add missing ethernet reset ID
firmware: arm_scmi: Fix duplicate workqueue name
firmware: arm_scmi: Fix locking in notifications
...
Another round of wack-a-mole. The json-schema default is additional
unknown properties are allowed, but for DT all properties should be
defined.
Signed-off-by: Rob Herring <robh@kernel.org>
In order to add meta-schema checks for additional/unevaluatedProperties
being present, all schema need to make this explicit. As the top-level
board/SoC schemas always have additional properties, add
'additionalProperties: true'.
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201005183830.486085-4-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Add missing properties that are currently used in the examples of
subnode bindings and in many DTs.
Also updates the example in sound/google,cros-ec-codec.yaml to comply
with the google,cros-ec binding.
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Link: https://lore.kernel.org/r/20201021114308.25485-4-ricardo.canuelo@collabora.com
[robh: Add missing '#address-cells' and '#size-cells']
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the google,cros-ec-keyb binding to YAML and add it as a property
of google,cros-ec.yaml
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Link: https://lore.kernel.org/r/20201021114308.25485-3-ricardo.canuelo@collabora.com
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the google,cros-ec-i2c-tunnel binding to YAML and add it as a
property of google,cros-ec.yaml.
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Link: https://lore.kernel.org/r/20201021114308.25485-2-ricardo.canuelo@collabora.com
[robh: add ref to i2c-controller.yaml]
Signed-off-by: Rob Herring <robh@kernel.org>
We have a few leftovers from the merge window period in
drm-misc-next-fixes, let's bring them into drm-misc-fixes
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add compatible string for V3s, with H3 one as fallback.
This is used in device tree now, but not standardized in DT binding.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201003235018.1121618-2-icenowy@aosc.io
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As the binding documentation says, #mbox-cells must have a value of 2,
but the example use a value 3. The MT8173 device tree correctly use
mbox-cells = <2>. This commit fixes the example.
Fixes: 19d8e335d5 ("dt-binding: gce: remove atomic_exec in mboxes property")
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20201018193016.3339045-1-fparent@baylibre.com
Signed-off-by: Rob Herring <robh@kernel.org>
Update the leds/common.yaml to indicate that the max color ID is 9.
Reflect the same change in the leds-class-multicolor.yaml
Reported-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20201016115703.30184-1-dmurphy@ti.com
Signed-off-by: Rob Herring <robh@kernel.org>
Various driver updates for platforms. A bulk of this is smaller fixes or
cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs
and platforms.
-----BEGIN PGP SIGNATURE-----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=tfPb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
