The Zynq UltraScale+ Devices Register Reference states that the WAKEUP
bit "should be set to 0 after the MCU sleep status bit gets back to 0."
If this is not done, the mcu is not going to sleep on reset and fail the
reset.
Set WAKEUP to 0 before triggering a reset to make sure that the reset is
successful.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cpb_size is given in kilobytes, but the bitrate is given in bits per
second. Therefore, the calculation of the initial removal delay and the
cpb size for the firmware were wrong.
Convert the bitrate to kilobytes before calculating the cpb size in 90
kHz units for sending it to the firmware. Also reuse the result for the
initial removal delay, to make it obvious that we are setting the
initial removal delay to the maximum value.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When creating a channel, freq_idr defines the number of frames between
IDR frames in the coded stream. In V4L2, the period between IDR frames
shall be taken from the GOP_SIZE control.
Set the IDR frame frequency equal to the GOP size and let every GOP
start with an IDR frame.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The subframe_latency and lda_control_mode fields directly follow
freq_golden_ref field and there is no unknown field in between. The
unknown field it at the end of the message.
Reorder the fields accordingly. This further allows to drop the hard
coded value from the lda_control_mode field and set the mode to 0.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The gop_length field is actually only u16 and there are two more u8
fields in the message:
- the number of consecutive b-frames
- frequency of golden frames
Fix the message and thus fix the configuration of the GOP length.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Only negative values are actual errors and positive values are used for
warnings. Warnings should not fail the encoding process.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The codec firmware uses error codes to report errors during the
configuration of a channel or while encoding a frame. Translate them
into human readable strings for debugging.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since commit cc62c74749 ("media: allegro: add missed checks in
allegro_open()") the allegro device does provide v4l2 controls to user
space anymore. The reason is that v4l2_fh_init() initializes
fh->ctrl_handler to vdev->ctrl_handler, which invalidates the previous
driver override of the ctrl_handler.
Therefore, v4l2_fh_init() must be called before the driver overrides the
fh->ctrl_handler with its own handler.
Move the initialization of the fh back to the top, as the initialization
does not does not need to be reverted on errors, but it is enough to
free the channel.
Fixes: cc62c74749 ("media: allegro: add missed checks in allegro_open()")
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This function is no longer used by other drivers, so it can be
made static.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This argument refers to a stable name for an HDMI port, mostly i915
(ACPI) specific. Since we'll be introducing a more generic 'name' argument
as well later, rename this now to avoid confusion.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch makes use of to_vpfe() to get a pointer to vpfe_device
Signed-off-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The code is called MEDIA_BUS_FMT_Y14_1X14 and behaves just like
MEDIA_BUS_FMT_Y12_1X12 with two more bits.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The new format is called V4L2_PIX_FMT_Y14. Like V4L2_PIX_FMT_Y10 and
V4L2_PIX_FMT_Y12 it is stored in two bytes per pixel but has only two
unused bits at the top.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This new ioctl retrieves a file's encryption nonce, which is useful for
testing. See the corresponding fs/crypto/ patch for more details.
Link: https://lore.kernel.org/r/20200314205052.93294-3-ebiggers@kernel.org
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Add an ioctl FS_IOC_GET_ENCRYPTION_NONCE which retrieves the nonce from
an encrypted file or directory. The nonce is the 16-byte random value
stored in the inode's encryption xattr. It is normally used together
with the master key to derive the inode's actual encryption key.
The nonces are needed by automated tests that verify the correctness of
the ciphertext on-disk. Except for the IV_INO_LBLK_64 case, there's no
way to replicate a file's ciphertext without knowing that file's nonce.
The nonces aren't secret, and the existing ciphertext verification tests
in xfstests retrieve them from disk using debugfs or dump.f2fs. But in
environments that lack these debugging tools, getting the nonces by
manually parsing the filesystem structure would be very hard.
To make this important type of testing much easier, let's just add an
ioctl that retrieves the nonce.
Link: https://lore.kernel.org/r/20200314205052.93294-2-ebiggers@kernel.org
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
When sja1105_init_mii_settings iterates over the port list, it prints
this message for disabled ports, because they don't have a valid
phy-mode:
[ 4.778702] sja1105 spi2.0: Unsupported PHY mode unknown!
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Suggested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->rbnode is sharing three skb fields : next, prev, dev
When a packet is sent, TCP keeps the original skb (master)
in a rtx queue, which was converted to rbtree a while back.
__tcp_transmit_skb() is responsible to clone the master skb,
and add the TCP header to the clone before sending it
to network layer.
skb_clone() already clears skb->next and skb->prev, but copies
the master oskb->dev into the clone.
We need to clear skb->dev, otherwise lower layers could interpret
the value as a pointer to a netdev.
This old bug surfaced recently when commit 28f8bfd1ac
("netfilter: Support iif matches in POSTROUTING") was merged.
Before this netfilter commit, skb->dev value was ignored and
changed before reaching dev_queue_xmit()
Fixes: 75c119afe1 ("tcp: implement rb-tree based retransmit queue")
Fixes: 28f8bfd1ac ("netfilter: Support iif matches in POSTROUTING")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Martin Zaharinov <micron10@gmail.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-03-19
Here's the main bluetooth-next pull request for the 5.7 kernel.
- Added wideband speech support to mgmt and the ability for HCI drivers
to declare support for it.
- Added initial support for L2CAP Enhanced Credit Based Mode
- Fixed suspend handling for several use cases
- Fixed Extended Advertising related issues
- Added support for Realtek 8822CE device
- Added DT bindings for QTI chip WCN3991
- Cleanups to replace zero-length arrays with flexible-array members
- Several other smaller cleanups & fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Chromebook BIOS' do not export an ACPI LPIT, which is how
Linux finds the residency counter for CPU and SYSTEM low power states,
that is exports in /sys/devices/system/cpu/cpuidle/*residency_us
When these sysfs attributes are missing, check the debugfs attrubte
from the pmc_core driver, which accesses the same counter value.
Signed-off-by: Len Brown <len.brown@intel.com>
From a turbostat point of view the Tremont-based Elkhart Lake
is very similar to Goldmont, reuse the code of Goldmont.
Elkhart Lake does not support 'group turbo limit counter'
nor C3, adjust the code accordingly.
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Jasper Lake, like Elkhart Lake, uses a Tremont CPU.
So reuse the code.
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
From a turbostat point of view, Ice Lake server looks like Sky Lake server.
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
From a turbostat point of view, Tiger Lake looks like Ice Lake.
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Warning: ‘__builtin_strncpy’ specified bound 20 equals destination size
[-Wstringop-truncation]
reduce param to strncpy, to guarantee that a null byte is always copied
into destination buffer.
Signed-off-by: Len Brown <len.brown@intel.com>
From a turbostat point of view, Cometlake is like Kabylake.
Suggested-by: Rui Zhang <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Driver reclaims descriptors in much smaller batches, even if hardware
indicates more to reclaim, during backpressure. So, fix the check to
restart the Txq during backpressure, by looking at how many
descriptors hardware had indicated to reclaim, and not on how many
descriptors that driver had actually reclaimed. Once the Txq is
restarted, driver will reclaim even more descriptors when Tx path
is entered again.
Fixes: d429005fdf ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Certain QCOM SoCs like ipq8064, apq8064, msm8960, msm8974
that has KRAIT processors the voltage/current value of each OPP
varies based on the silicon variant in use.
The required OPP related data is determined based on
the efuse value. This is similar to the existing code for
kryo cores. So adding support for krait cores here.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
commit 7c3bebc3d8 ("cxgb4: request the TX CIDX updates to status page")
reverted back to getting Tx CIDX updates via DMA, instead of interrupts,
introduced by commit d429005fdf ("cxgb4/cxgb4vf: Add support for SGE
doorbell queue timer")
However, it missed reverting back several code changes where Tx CIDX
updates are not explicitly requested during backpressure when using
interrupt mode. These missed changes cause slow recovery during
backpressure because the corresponding interrupt no longer comes and
hence results in Tx throughput drop.
So, revert back these missed code changes, as well, which will allow
explicitly requesting Tx CIDX updates when backpressure happens.
This enables the corresponding interrupt with Tx CIDX update message
to get generated and hence speed up recovery and restore back
throughput.
Fixes: 7c3bebc3d8 ("cxgb4: request the TX CIDX updates to status page")
Fixes: d429005fdf ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi says:
====================
add more xdp stats to veth driver
Align veth xdp stats accounting to mellanox, intel and marvell
implementation. Introduce the following xdp counters:
- rx_xdp_tx
- rx_xdp_tx_errors
- tx_xdp_xmit
- tx_xdp_xmit_errors
- rx_xdp_redirect
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove atomic64_add from veth_xdp_xmit hotpath and rely on
xdp_xmit_err/xdp_tx_err counters
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce xdp_xmit counter in order to distinguish between XDP_TX and
ndo_xdp_xmit stats. Introduce the following ethtool counters:
- rx_xdp_tx
- rx_xdp_tx_errors
- tx_xdp_xmit
- tx_xdp_xmit_errors
- rx_xdp_redirect
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Distinguish between rx_drops and xdp_drops since the latter is already
reported in rx_packets. Report xdp_drops in ethtool statistics
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce xdp_tx, xdp_redirect and rx_drops counters in veth_stats data
structure. Move stats accounting in veth_poll. Remove xdp_xmit variable
in veth_xdp_rcv_one/veth_xdp_rcv_skb and rely on veth_stats counters.
This is a preliminary patch to align veth xdp statistics to mlx, intel
and marvell xdp implementation
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move xdp stats in veth_stats data structure. This is a preliminary patch
to align xdp statistics to mlx5, ixgbe and mvneta drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_SYSFS declaration of sysfs_group_change_owner() is different
from the !CONFIG_SYSFS version and thus causes build failurs when
!CONFIG_SYSFS is set.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 303a42769c ("sysfs: add sysfs_group{s}_change_owner()")
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart says:
====================
net: phy: mscc: add support for RGMII MAC mode
This series adds support for the RGMII MAC mode for the VSC8584 PHY
family and for RGMII_ID modes (Tx and/or Rx).
I decided to drop the custom delay for now. I made some tests and it
seemed to be working quite well. If we find out we really need to lower
the delay, which I doubt, I'll send support for it.
Since v2:
- Dropped support for custom dt bindings.
- Add the 2ns delay based on the interface mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for configuring the RGMII skew delays in Rx and
Tx. The Rx and Tx skews are set based on the interface mode. By default
their configuration is set to the default value in hardware (0.2ns);
this means the driver do not rely anymore on the bootloader
configuration.
Then based on the interface mode being used, a 2ns delay is added:
- RGMII_ID adds it for both Rx and Tx.
- RGMII_RXID adds it for Rx.
- RGMII_TXID adds it for Tx.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for connecting VSC8584 PHYs to the MAC using
RGMII.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew reported:
After a number of network port link up/down changes, sometimes the switch
port gets stuck in a state where it thinks it is still transmitting packets
but the cpu port is not actually transmitting anymore. In this state you
will see a message on the console
"mtk_soc_eth 1e100000.ethernet eth0: transmit timed out" and the Tx counter
in ifconfig will be incrementing on virtual port, but not incrementing on
cpu port.
The issue is that MAC TX/RX status has no impact on the link status or
queue manager of the switch. So the queue manager just queues up packets
of a disabled port and sends out pause frames when the queue is full.
Change the LINK bit to reflect the link status.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Reported-by: Andrew Smith <andrew.smith@digi.com>
Signed-off-by: René van Dorst <opensource@vdorst.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Offload TC action skbedit priority
Petr says:
The TC action "skbedit priority P" has the effect of assigning skbprio of P
to SKBs that it's applied on. In HW datapath of a switch, the corresponding
action is assignment of internal switch priority. Spectrum switches allow
setting of packet priority based on an ACL action, which is good match for
the skbedit priority gadget. This patchset therefore implements offloading
of this action to the Spectrum ACL engine.
After a bit of refactoring in patch #1, patch #2 extends the skbedit action
to support offloading of "priority" subcommand.
On mlxsw side, in patch #3, the QOS_ACTION flexible action is added, with
fields necessary for priority adjustment. In patch #4, "skbedit priority"
is connected to that action.
Patch #5 implements a new forwarding selftest, suitable for both SW- and
HW-datapath testing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that runs traffic through a port such that skbedit priority
action acts on it during forwarding. Test that at egress, it is classified
correctly according to the new priority at a PRIO qdisc.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offload action skbedit priority when keyed to a flower classifier. The
skb->priority field in Linux is very generic, so only allow setting the
bottom 8 priorities and bounce anything else.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QOS_ACTION is used for manipulating the QoS attributes of a packet.
Add the corresponding defines and helpers, in particular for the
switch_priority override.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skbedit action "priority" is used for adjusting SKB priority. Allow
drivers to offload the action by introducing two new skbedit getters and a
new flow action, and initializing appropriately in tc_setup_flow_action().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two functions is_tcf_skbedit_mark() and is_tcf_skbedit_ptype() have a
very similar structure. A follow-up patch will add one more such function.
Instead of more cut'n'pasting, extract a helper function that checks
whether a TC action is an skbedit with the required flag. Convert the two
existing functions into thin wrappers around the helper.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it will check the return value of dwmac_dma_reset() in the
stmmac_init_dma_engine() function and report an error if the
return value is not zero. so don't need check here.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
