This adds support for the MediaTek MT6397 PMIC. This is a
multifunction device with the following sub modules:
- Regulator
- RTC
- Audio codec
- GPIO
- Clock
It is interfaced to the host controller using SPI interface by a proprietary
hardware called PMIC wrapper or pwrap. MT6397 MFD is a child device of the
pwrap.
Signed-off-by: Flora Fu, MediaTek
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This change adds a new Kconfig option MPLS_ROUTING.
The core of this change is the code to look at an mpls packet received
from another machine. Look that packet up in a routing table and
forward the packet on.
Support of MPLS over ATM is not considered or attempted here. This
implemntation follows RFC3032 and implements the MPLS shim header that
can pass over essentially any network.
What RFC3021 refers to as the as the Incoming Label Map (ILM) I call
net->mpls.platform_label[]. What RFC3031 refers to as the Next Label
Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the
label fordwarding information base (lfib) might also be valid.
Further the implemntation forwards packets as described in RFC3032.
There is no need and given the original motivation for MPLS a strong
discincentive to have a flexible label forwarding path. In essence
the logic is the topmost label is read, looked up, removed, and
replaced by 0 or more new lables and the sent out the specified
interface to it's next hop.
Quite a few optional features are not implemented here. Among them
are generation of ICMP errors when the TTL is exceeded or the packet
is larger than the next hop MTU (those conditions are detected and the
packets are dropped instead of generating an icmp error). The traffic
class field is always set to 0. The implementation focuses on IP over
MPLS and does not handle egress of other kinds of protocols.
Instead of implementing coordination with the neighbour table and
sorting out how to input next hops in a different address family (for
which there is value). I was lazy and implemented a next hop mac
address instead. The code is simpler and there are flavor of MPLS
such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is
appropriate so a next hop by mac address would need to be implemented
at some point.
Two new definitions AF_MPLS and PF_MPLS are exposed to userspace.
Decoding the mpls header must be done by first byeswapping a 32bit bit
endian word into the local cpu endian and then bit shifting to extract
the pieces. There is no C bit-field that can represent a wire format
mpls header on a little endian machine as the low bits of the 20bit
label wind up in the wrong half of third byte. Therefore internally
everything is deal with in cpu native byte order except when writing
to and reading from a packet.
For management simplicity if a label is configured to forward out
an interface that is down the packet is dropped early. Similarly
if an network interface is removed rt_dev is updated to NULL
(so no reference is preserved) and any packets for that label
are dropped. Keeping the label entries in the kernel allows
the kernel label table to function as the definitive source
of which labels are allocated and which are not.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
arizona_extcon_do_magic does not lend a lot of clarity to the purpose
of the function, and as all the registers used are described in the
datasheet there is no need to obfuscate the code. This patch renames the
function to arizona_extcon_hp_clamp, as it controls clamping on the
headphone output.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Pull networking fixes from David Miller:
1) If an IPVS tunnel is created with a mixed-family destination
address, it cannot be removed. Fix from Alexey Andriyanov.
2) Fix module refcount underflow in netfilter's nft_compat, from Pablo
Neira Ayuso.
3) Generic statistics infrastructure can reference variables sitting on
a released function stack, therefore use dynamic allocation always.
Fix from Ignacy Gawędzki.
4) skb_copy_bits() return value test is inverted in ip_check_defrag().
5) Fix network namespace exit in openvswitch, we have to release all of
the per-net vports. From Pravin B Shelar.
6) Fix signedness bug in CAIF's cfpkt_iterate(), from Dan Carpenter.
7) Fix rhashtable grow/shrink behavior, only expand during inserts and
shrink during deletes. From Daniel Borkmann.
8) Netdevice names with semicolons should never be allowed, because
they serve as a separator. From Matthew Thode.
9) Use {,__}set_current_state() where appropriate, from Fabian
Frederick.
10) Revert byte queue limits support in r8169 driver, it's causing
regressions we can't figure out.
11) tcp_should_expand_sndbuf() erroneously uses tp->packets_out to
measure packets in flight, properly use tcp_packets_in_flight()
instead. From Neal Cardwell.
12) Fix accidental removal of support for bluetooth in CSR based Intel
wireless cards. From Marcel Holtmann.
13) We accidently added a behavioral change between native and compat
tasks, wrt testing the MSG_CMSG_COMPAT bit. Just ignore it if the
user happened to set it in a native binary as that was always the
behavior we had. From Catalin Marinas.
14) Check genlmsg_unicast() return valud in hwsim netlink tx frame
handling, from Bob Copeland.
15) Fix stale ->radar_required setting in mac80211 that can prevent
starting new scans, from Eliad Peller.
16) Fix memory leak in nl80211 monitor, from Johannes Berg.
17) Fix race in TX index handling in xen-netback, from David Vrabel.
18) Don't enable interrupts in amx-xgbe driver until all software et al.
state is ready for the interrupt handler to run. From Thomas
Lendacky.
19) Add missing netlink_ns_capable() checks to rtnl_newlink(), from Eric
W Biederman.
20) The amount of header space needed in macvtap was not calculated
properly, fix it otherwise we splat past the beginning of the
packet. From Eric Dumazet.
21) Fix bcmgenet TCP TX perf regression, from Jaedon Shin.
22) Don't raw initialize or mod timers, use setup_timer() and
mod_timer() instead. From Vaishali Thakkar.
23) Fix software maintained statistics in bcmgenet and systemport
drivers, from Florian Fainelli.
24) DMA descriptor updates in sh_eth need proper memory barriers, from
Ben Hutchings.
25) Don't do UDP Fragmentation Offload on RAW sockets, from Michal
Kubecek.
26) Openvswitch's non-masked set actions aren't constructed properly
into netlink messages, fix from Joe Stringer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
openvswitch: Fix serialization of non-masked set actions.
gianfar: Reduce logging noise seen due to phy polling if link is down
ibmveth: Add function to enable live MAC address changes
net: bridge: add compile-time assert for cb struct size
udp: only allow UFO for packets from SOCK_DGRAM sockets
sh_eth: Really fix padding of short frames on TX
Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
sh_eth: Ensure proper ordering of descriptor active bit write/read
net/mlx4_en: Disbale GRO for incoming loopback/selftest packets
net/mlx4_core: Fix wrong mask and error flow for the update-qp command
net: systemport: fix software maintained statistics
net: bcmgenet: fix software maintained statistics
rxrpc: don't multiply with HZ twice
rxrpc: terminate retrans loop when sending of skb fails
net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface.
net: pasemi: Use setup_timer and mod_timer
net: stmmac: Use setup_timer and mod_timer
net: 8390: axnet_cs: Use setup_timer and mod_timer
net: 8390: pcnet_cs: Use setup_timer and mod_timer
...
Add of_pci_dma_configure() to allow updating the DMA configuration of the
PCI device using the configuration from DT of the parent of the root bridge
device. Use the newly added APIs pci_get/put_host_bridge_device() for
implementing this.
[bhelgaas: fold in fix for host bridges with no parent OF device]
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> (AMD Seattle)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
CC: Joerg Roedel <joro@8bytes.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: Arnd Bergmann <arnd@arndb.de>
Move of_dma_configure() to device.c so it can be re-used for PCI devices to
obtain DMA configuration from DT. Also add a second argument so that for
PCI, the DT node of root bus host bridge can be used to obtain the DMA
configuration for the slave PCI device.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> (AMD Seattle)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
CC: Joerg Roedel <joro@8bytes.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: Arnd Bergmann <arnd@arndb.de>
of_iommu_configure() is called from of_dma_configure() to setup iommu ops
using DT property. This API is currently used for platform devices for
which DMA configuration (including IOMMU ops) may come from the device's
parent. To extend this functionality for PCI devices, this API needs to
take a parent node ptr as an argument instead of assuming device's parent.
This is needed since for PCI, the DMA configuration may be defined in the
DT node of the root bus bridge's parent device. Currently only dma-range
is used for PCI and IOMMU is not supported. Return error if the device is
PCI.
Add "parent" parameter (a struct device_node *) to of_iommu_configure().
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> (AMD Seattle)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
CC: Joerg Roedel <joro@8bytes.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: Arnd Bergmann <arnd@arndb.de>
The rcu_dereference_check() family of primitives evaluates the RCU
lockdep expression first, and only then evaluates the expression passed
in. This works fine normally, but can potentially fail in environments
(such as NMI handlers) where lockdep cannot be invoked. The problem is
that even if the expression passed in is "1", the compiler would need to
prove that the RCU lockdep expression (rcu_read_lock_held(), for example)
is free of side effects in order to be able to elide it. Given that
rcu_read_lock_held() is sometimes separately compiled, the compiler cannot
always use this optimization.
This commit therefore reverse the order of evaluation, so that the
expression passed in is evaluated first, and the RCU lockdep expression is
evaluated only if the passed-in expression evaluated to false, courtesy
of the C-language short-circuit boolean evaluation rules. This compells
the compiler to forego executing the RCU lockdep expression in cases
where the passed-in expression evaluates to "1" at compile time, so that
(for example) rcu_dereference_raw() can be guaranteed to execute safely
within an NMI handler.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
If an RCU read-side critical section occurs within an interrupt handler
or a softirq handler, it cannot have been preempted. Therefore, there is
a check in rcu_read_unlock_special() checking for this error. However,
when this check triggers, it lacks diagnostic information. This commit
therefore moves rcu_read_unlock()'s lockdep annotation to follow the
call to __rcu_read_unlock() and changes rcu_read_unlock_special()'s
WARN_ON_ONCE() to an lockdep_rcu_suspicious() in order to locate where
the offending RCU read-side critical section began. In addition, the
value of the ->rcu_read_unlock_special field is printed.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
When invalidating the page cache for a regular file, we want to first
sync all dirty data to disk and then call invalidate_inode_pages2().
The latter relies on nfs_launder_page() and nfs_release_page() to deal
respectively with dirty pages, and unstable written pages.
When commit 9590544694 ("NFS: avoid deadlocks with loop-back mounted
NFS filesystems.") changed the behaviour of nfs_release_page(), then it
made it possible for invalidate_inode_pages2() to fail with an EBUSY.
Unfortunately, that error is then propagated back to read().
Let's therefore work around the problem for now by protecting the call
to sync the data and invalidate_inode_pages2() so that they are atomic
w.r.t. the addition of new writes.
Later on, we can revisit whether or not we still need nfs_launder_page()
and nfs_release_page().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Rename a filed name from 'blk_addr' to 'blk' in struct {f2fs_extent,extent_info}
as annotation of this field descripts its meaning well to us.
By this way, we can avoid long statement in code of following patches.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The WTSR (Watchdog Timer Software Reset) and SMPL (Sudden Momentary
Power Loss) were removed from rtc-s5m driver because they were not used.
Remove them (and on/off interrupt) from main MFD driver and header.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move parts of linux/mfd/arizona/pdata.h and gpio.h into a new file in
the dt-binding directory for use by device tree bindings. This also
makes gpio.h redundant so remove it in the process.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To enable/disable ASPM we should find LINK CONTROL register
in PCI config space. All old chip use 0x80 address, but new
chip may use another address, so we using pci_find_capability()
to get LINK CONTROL address.
rtsx_gops.c was removed, we consider to put some common operations
to this file, but the actual thing is, only a group of chips
are in common ops1, and another group of chips in common ops2,
it is hard to decide put which ops into generic ops file.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Update some phy register name and value for rts5249,
the updated value makes chip more stable on some platform.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
PETXCFG is defined at 0xFF03, the old 0xFE49 not used any more.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is more readable to place register address and values define
togather. The values define add two leading space indicate belong
to the register address defined above.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Re-format coding-style, using uniform SPC after "#define" keyword
instead of mixing using TAB and SPC.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In one shot mode, sequencer automatically disables all enabled steps at
the end of each cycle. (both ADC steps and TSC steps) Hence these steps
need not be saved in reg_se_cache for clearing these steps at a later
stage.
Also, when ADC wakes up Sequencer should not be busy executing any of the
config steps except for the charge step. Previously charge step was 1 ADC
clock cycle and hence it was ignored.
TSC steps are always disabled at the end of each conversion cycle, hence
there is no need to explicitly disable TSC steps by writing 0 to REG_SE.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull thermal management fixes from Eduardo Valentin:
"Specifics:
- Several fixes in tmon tool.
- Fixes in intel int340x for _ART and _TRT tables.
- Add id for Avoton SoC into powerclamp driver.
- Fixes in RCAR thermal driver to remove race conditions and fix fail
path
- Fixes in TI thermal driver: removal of unnecessary code and build
fix if !CONFIG_PM_SLEEP
- Cleanups in exynos thermal driver
- Add stubs for include/linux/thermal.h. Now drivers using thermal
calls but that also work without CONFIG_THERMAL will be able to
compile for systems that don't care about thermal.
Note: I am sending this pull on Rui's behalf while he fixes issues in
his Linux box"
* 'fixes-for-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: int340x_thermal: Ignore missing _ART, _TRT tables
thermal/intel_powerclamp: add id for Avoton SoC
tools/thermal: tmon: silence 'set but not used' warnings
tools/thermal: tmon: use pkg-config to determine library dependencies
tools/thermal: tmon: support cross-compiling
tools/thermal: tmon: add .gitignore
tools/thermal: tmon: fixup tui windowing calculations
tools/thermal: tmon: tui: don't hard-code dialog window size assumptions
tools/thermal: tmon: add min/max macros
tools/thermal: tmon: add --target-temp parameter
thermal: exynos: Clean-up code to use oneline entry for exynos compatible table
thermal: rcar: Make error and remove paths symmetrical with init
thermal: rcar: Fix race condition between init and interrupt
thermal: Introduce dummy functions when thermal is not defined
ti-soc-thermal: Delete an unnecessary check before the function call "cpufreq_cooling_unregister"
thermal: ti-soc-thermal: bandgap: Fix build warning if !CONFIG_PM_SLEEP
Now that there are no more users kill dev_rebuild_header and all of it's
implementations.
This is long overdue.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit mask for currently supported driver features (MLX4_UPDATE_QP_SUPPORTED_ATTRS)
of the update-qp command was defined twice (using enum value and pre-processor
define directive) and wrong.
The return value of the call to mlx4_update_qp() from within the SRIOV
resource-tracker was wrongly voided down.
Fix both issues.
issue: none
Fixes: 09e05c3f78 ('net/mlx4: Set vlan stripping policy by the right command')
Fixes: ce8d9e0d67 ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Masami noted that it would be better to hide the remaining CONFIG_BPF_SYSCALL-only
function declarations within the BPF header ifdef, w/o else path dummy alternatives
since these functions are not supposed to have a user outside of CONFIG_BPF_SYSCALL.
Suggested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Reference: http://article.gmane.org/gmane.linux.kernel.api/8658
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-03-02
Here's the first bluetooth-next pull request targeting the 4.1 kernel:
- ieee802154/6lowpan cleanups
- SCO routing to host interface support for the btmrvl driver
- AMP code cleanups
- Fixes to AMP HCI init sequence
- Refactoring of the HCI callback mechanism
- Added shutdown routine for Intel controllers in the btusb driver
- New config option to enable/disable Bluetooth debugfs information
- Fix for early data reception on L2CAP fixed channels
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After TIPC doesn't depend on iocb argument in its internal
implementations of sendmsg() and recvmsg() hooks defined in proto
structure, no any user is using iocb argument in them at all now.
Then we can drop the redundant iocb argument completely from kinds of
implementations of both sendmsg() and recvmsg() in the entire
networking stack.
Cc: Christoph Hellwig <hch@lst.de>
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cos table used at fixp-arith.h has only 8 bits of precision.
That causes problems if it is reused on other drivers.
As some media drivers require a higher precision sin/cos
implementation, replace the current implementation by one that
will provide 32 bits precision.
The values generated by the new implementation matches the
32 bit precision of glibc's sin for an angle measured in
integer degrees.
It also provides support for fractional angles via linear
interpolation. On experimental calculus, when used a table
with a 0.001 degree angle, the maximum error for sin is
0.000038, which is likely good enough for practical purposes.
There are some logic there that seems to be specific to the
usage inside ff-memless.c. Move those logic to there, as they're
not needed elsewhere.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It doesn't operate on PCI core, but PCI host device, so there is no
point of passing core related struct.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bringing PCIe hosted bus up requires operating on host-related core.
Since we plan to support PCIe Gen 2 devices we should provide a helper
picking the correct one (PCIE or PCIE2).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds a macro to define the GPR3 MIPI muxing control register field
shift bits.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Commit 977750076d ("af_packet: add interframe drop cmsg (v6)")
unionized skb->mark and skb->dropcount in order to allow recording
of the socket drop count while maintaining struct sk_buff size.
skb->dropcount was introduced since there was no available room
in skb->cb[] in packet sockets. However, its introduction led to
the inability to export skb->mark, or any other aliased field to
userspace if so desired.
Moving the dropcount metric to skb->cb[] eliminates this problem
at the expense of 4 bytes less in skb->cb[] for protocol families
using it.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PADT frame is received, the socket may not be in a good state to
close down the PPP interface. The current implementation handles this by
simply blocking all further PPP traffic, and hoping that the lack of traffic
will trigger the user to investigate.
Use schedule_work to get to a process context from which we clear down the
PPP interface, in a fashion analogous to hangup on a TTY-based PPP
interface. This causes pppd to disconnect immediately, and allows tools to
take immediate corrective action.
Note that pppd's rp_pppoe.so plugin has code in it to disable the session
when it disconnects; however, as a consequence of this patch, the session is
already disabled before rp_pppoe.so is asked to disable the session. The
result is a harmless error message:
Failed to disconnect PPPoE socket: 114 Operation already in progress
This message is safe to ignore, as long as the error is 114 Operation
already in progress; in that specific case, it means that the PPPoE session
has already been disabled before pppd tried to disable it.
Signed-off-by: Simon Farnsworth <simon@farnz.org.uk>
Tested-by: Dan Williams <dcbw@redhat.com>
Tested-by: Christoph Schulz <develop@kristov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that other operations that race with our write RPC calls
cannot revert the file size updates that were made on the server.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Ensure that other operations which raced with our setattr RPC call
cannot revert the file attribute changes that were made on the server.
To do so, we artificially bump the attribute generation counter on
the inode so that all calls to nfs_fattr_init() that precede ours
will be dropped.
The motivation for the patch came from Chuck Lever's reports of readaheads
racing with truncate operations and causing the file size to be reverted.
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Implement an API that gives additional control on the what VMBUS flags will be
set as well as if the host needs to be signalled. This API will be
useful for clients that want to batch up requests to the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement an API for sending pagebuffers that gives more control to the client
in terms of setting the vmbus flags as well as deciding when to
notify the host. This will be useful for enabling batch processing.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current algorithm for picking an outgoing channel was not distributing
the load well. Implement a simple round-robin scheme to ensure good
distribution of the outgoing traffic.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In response to a rescind message, we need to remove the channel and the
corresponding device. Cleanup this code path by factoring out the code
to remove a channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NetworkDirect is a service that supports guest RDMA.
Define the GUID for this service.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All channel work queues are named 'hv_vmbus_ctl', this makes them
indistinguishable in ps output and makes it hard to link to the corresponding
vmbus device. Rename them to hv_vmbus_ctl/N and make vmbus device names match,
e.g. now vmbus_1 device is served by hv_vmbus_ctl/1 work queue.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
is_gpl_compatible and prog_type should be moved directly into bpf_prog
as they stay immutable during bpf_prog's lifetime, are core attributes
and they can be locked as read-only later on via bpf_prog_select_runtime().
With a bit of rearranging, this also allows us to shrink bpf_prog_aux
to exactly 1 cacheline.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Socket filter code and other subsystems with upcoming eBPF support should
not need to deal with the fact that we have CONFIG_BPF_SYSCALL defined or
not.
Having the bpf syscall as a config option is a nice thing and I'd expect
it to stay that way for expert users (I presume one day the default setting
of it might change, though), but code making use of it should not care if
it's actually enabled or not.
Instead, hide this via header files and let the rest deal with it.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to export BPF_PSEUDO_MAP_FD to user space, as it's used in the
ELF BPF loader where instructions are being loaded that need map fixups.
An initial stage loads all maps into the kernel, and later on replaces
related instructions in the eBPF blob with BPF_PSEUDO_MAP_FD as source
register and the actual fd as immediate value.
The kernel verifier recognizes this keyword and replaces the map fd with
a real pointer internally.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can move bpf_map_ops and bpf_verifier_ops and other structs into ro
section, bpf_map_type_list and bpf_prog_type_list into read mostly.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
