Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of reading the silicon version from ROM, we should
read the SREV register from the IIM.
Freescale has dropped all support for MX51 REV1.0, only MX51
REV 2.0 and 3.0 are valid.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In KVM passthrough mode, the driver may not have config access to
non-standard registers. The BNX2_PCICFG_MISC_CONFIG config register
access to setup mailbox swapping can be done using MMIO.
Update version to 2.0.20.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5709 chip requires the BNX2_MISC_NEW_CORE_CTL_DMA_ENABLE bit to be
cleared and polling for pending DMAs to complete before chip reset.
Without this step, we've seen NMIs during repeated resets of the chip.
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the vlan device is lockless and single queue do not
transfer the real num queues. This is causing a BUG_ON to occur.
kernel BUG at net/8021q/vlan.c:345!
Call Trace:
[<ffffffff813fd6e8>] ? fib_rules_event+0x28/0x1b0
[<ffffffff814ad2b5>] notifier_call_chain+0x55/0x80
[<ffffffff81089156>] raw_notifier_call_chain+0x16/0x20
[<ffffffff813e5af7>] call_netdevice_notifiers+0x37/0x70
[<ffffffff813e6756>] netdev_features_change+0x16/0x20
[<ffffffffa02995be>] ixgbe_fcoe_enable+0xae/0x100 [ixgbe]
[<ffffffffa01da06a>] vlan_dev_fcoe_enable+0x2a/0x30 [8021q]
[<ffffffffa02d08c3>] fcoe_create+0x163/0x630 [fcoe]
[<ffffffff811244d5>] ? mmap_region+0x255/0x5a0
[<ffffffff81080ef0>] param_attr_store+0x50/0x80
[<ffffffff810809b6>] module_attr_store+0x26/0x30
[<ffffffff811b9db2>] sysfs_write_file+0xf2/0x180
[<ffffffff8114fc88>] vfs_write+0xc8/0x190
[<ffffffff81150621>] sys_write+0x51/0x90
[<ffffffff8100c0b2>] system_call_fastpath+0x16/0x1b
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing struct netdev_queue state against FROZEN bit, we also test
XOFF bit. We can test both bits at once and save some cycles.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. IPV6_TLV_TEL_DST_SIZE
This has not been using for several years since created.
2. RT6_INFO_LEN
commit 33120b30 kill all RT6_INFO_LEN's references, but only this definition remained.
commit 33120b30cc
Author: Alexey Dobriyan <adobriyan@sw.ru>
Date: Tue Nov 6 05:27:11 2007 -0800
[IPV6]: Convert /proc/net/ipv6_route to seq_file interface
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kdump environment do not depend on reset_devices
parameter to reset the device as the parameter may become obsolete.
Instead use an adapter specific mechanism to determine if the device
needs a reset.
Driver maintains a count of number of pci functions probed
and decrements the count when remove handler of that pci function
is called. If the first probe, probe of function 0,
detects the count as non zero then reset the device.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kdump environment do not depend upon reset_devices parameter
to reset the pci function as this parameter may become obsolete.
Instead use an adapter specific mechanism to determine if the pci
function needs to be reset.
Per function refcount is maintained in driver, which is set in probe
and reset in remove handler of adapter. If the probe detects the count
as non zero then reset the function.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros have been existed for several years since v2.6.12-rc2.
But they never be used. So remove them now.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_win_from_space() does the following:
if (sysctl_tcp_adv_win_scale <= 0)
return space >> (-sysctl_tcp_adv_win_scale);
else
return space - (space >> sysctl_tcp_adv_win_scale);
"space" is int.
As per C99 6.5.7 (3) shifting int for 32 or more bits is
undefined behaviour.
Indeed, if sysctl_tcp_adv_win_scale is exactly 32,
space >> 32 equals space and function returns 0.
Which means we busyloop in tcp_fixup_rcvbuf().
Restrict net.ipv4.tcp_adv_win_scale to [-31, 31].
Fix https://bugzilla.kernel.org/show_bug.cgi?id=20312
Steps to reproduce:
echo 32 >/proc/sys/net/ipv4/tcp_adv_win_scale
wget www.kernel.org
[softlockup]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't track gpu flush request in any special way. So even with
obj->write_domain == 0, a gpu flush might be outstanding but no
yet executed. Even worse, the latest request might use the object
only for reading. So and unconditional call to object_wait_rendering
is needed for !pipelined.
Hence revert that patch fully and untangle the flushing from the
synchronization again.
Reported-by: Keith Packard <keithp@keithp.com>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the guest domain has been suspend/resumed or migrated, then the
system clock backing the pvclock clocksource may revert to a smaller
value (ie, can be non-monotonic across the migration/save-restore).
Make sure we zero last_value in that case so that the domain
continues to see clock updates.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The /proc/net/tcp leaks openreq sockets from other namespaces.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As David pointed out correctly, updates to af-specific attributes
are currently not atomic. If multiple changes are requested and
one of them fails, previous updates may have been applied already
leaving the link behind in a undefined state.
This patch splits the function parse_link_af() into two functions
validate_link_af() and set_link_at(). validate_link_af() is placed
to validate_linkmsg() check for errors as early as possible before
any changes to the link have been made. set_link_af() is called to
commit the changes later.
This method is not fail proof, while it is currently sufficient
to make set_link_af() inerrable and thus 100% atomic, the
validation function method will not be able to detect all error
scenarios in the future, there will likely always be errors
depending on states which are f.e. not protected by rtnl_mutex
and thus may change between validation and setting.
Also, instead of silently ignoring unknown address families and
config blocks for address families which did not register a set
function the errors EAFNOSUPPORT respectively EOPNOSUPPORT are
returned to avoid comitting 4 out of 5 update requests without
notifying the user.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vzalloc() and vzalloc_node() in net drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Key changes are:
- EQ ids are not assigned consecutively in Lancer. So, fix mapping of MSIx
vector to EQ-id.
- BAR mapping and some req locations different for Lancer.
- TCP,UDP,IP checksum fields must be compulsorily set in TX wrb for TSO in
Lancer.
- CEV_IST reg not present in Lancer; so, peek into event queue to check for
new entries
- cq_create and mcc_create cmd interface is different for Lancer; handle
accordingly
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the if and else conditional because the code is in mainline and there
is no need in it being there.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 9b7f76dc37919ea36caa9680a3f765e5b19b25fb,
Author: Lars Ellenberg <lars.ellenberg@linbit.com>
Date: Wed Aug 11 23:40:24 2010 +0200
drbd: new configuration parameter c-min-rate
a bad chunk slipped through, which is now reverted as well,
restoring the correct irqsave for the endio callback.
This patch also add comments at both req_mod()
and in the endio callback so it should not happen again.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This should fix a performance degradation we observed recently.
If we don't expect any subheader, we should not call into the tcp stack,
as that may add considerable latency if there is no data available at
this point.
For a synthetic synchronous write load with single outstanding writes,
this additional latency when processing the "unplug remote" packet
added up to a performance degradation factor >= 10.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
There is a problem with how we use sget, it searches through the list of supers
attached to the fs_type looking for a super with the same fs_devices as what
we're trying to mount. This depends on sb->s_fs_info being filled, but we don't
fill that in until we get to btrfs_fill_super, so we could hit supers on the
fs_type super list that have a null s_fs_info. In order to fix that we need to
go ahead and setup a blank root with a blank fs_info to hold fs_devices, that
way our test will work out right and then we can set s_fs_info in
btrfs_set_super, and then open_ctree will simply use our pre-allocated root and
fs_info when setting everything up. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
There are two big problems currently with FIEMAP
1) We return extents for holes. This isn't supposed to happen, we just don't
return extents for holes and then userspace interprets the lack of an extent as
a hole.
2) We sometimes don't set FIEMAP_EXTENT_LAST properly. This is because we wait
to see a EXTENT_FLAG_VACANCY flag on the em, but this won't happen if say we ask
fiemap to map up to the last extent in a file, and there is nothing but holes up
to the i_size. To fix this we need to lookup the last extent in this file and
save the logical offset, so if we happen to try and map that extent we can be
sure to set FIEMAP_EXTENT_LAST.
With this patch we now pass xfstest 225, which we never have before.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When mounting a btrfs file system btrfs_test_super() may attempt to
use sb->s_fs_info, the btrfs root, of a super block that is going away
and that has had the btrfs root set to NULL in its ->put_super(). But
if the super block is going away it cannot be an existing super block
so we can return false in this case.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Currently we fail xfstest 236 because we're not updating the inode ctime on
link. This is a simple fix, and makes it so we pass 236 now.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
We have been failing xfstest 228 forever, because we don't check to make sure
the new inode size is acceptable as far as RLIMIT is concerned. Just check to
make sure it's ok to create a inode with this new size and error out if not.
With this patch we now pass 228.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
There is a typo in __btrfs_prealloc_file_range() where we set the i_size to
actual_len/cur_offset, and then just set it to cur_offset again, and do the same
with btrfs_ordered_update_i_size(). This fixes it back to keeping i_size in a
local variable and then updating i_size properly. Tested this with
xfs_io -F -f -c "falloc 0 1" -c "pwrite 0 1" foo
stat'ing foo gives us a size of 1 instead of 4096 like it was. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Fix it by explaining what can be happening and giving the number of processed
and lost events.
Also holler if unknown events were found, that can be due to processing a
perf.data file collected using a newer tool where newer events got added on
reporting using an older perf tool, that or a bug, so ask for a report to be
made.
Works on both --tui and --stdio.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Some filesystems like xfs and reiserfs will return DT_UNKNOWN for the
d_type. Handle this case by calling stat() to determine the type.
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1290355779-3276-1-git-send-email-sbohrer@rgmadvisors.com>
Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
If a 32bit userspace perf is running on a 64bit kernel, the end of the final
map in the kernel would incorrectly be set to 2^32-1 rather than 2^64-1.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1290658375-10342-1-git-send-email-imunsie@au1.ibm.com>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Ensure we return the dirent->d_type when it is known
NFS: Correct the array bound calculation in nfs_readdir_add_to_array
NFS: Don't ignore errors from nfs_do_filldir()
NFS: Fix the error handling in "uncached_readdir()"
NFS: Fix a page leak in uncached_readdir()
NFS: Fix a page leak in nfs_do_filldir()
NFS: Assume eof if the server returns no readdir records
NFS: Buffer overflow in ->decode_dirent() should not be fatal
Pure nfs client performance using odirect.
SUNRPC: Fix an infinite loop in call_refresh/call_refreshresult
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
dmar, x86: Use function stubs when CONFIG_INTR_REMAP is disabled
x86-64: Fix and clean up AMD Fam10 MMCONF enabling
x86: UV: Address interrupt/IO port operation conflict
x86: Use online node real index in calulate_tbl_offset()
x86, asm: Fix binutils 2.15 build failure
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf symbols: Remove incorrect open-coded container_of()
perf record: Handle restrictive permissions in /proc/{kallsyms,modules}
x86/kprobes: Prevent kprobes to probe on save_args()
irq_work: Drop cmpxchg() result
perf: Fix owner-list vs exit
x86, hw_nmi: Move backtrace_mask declaration under ARCH_HAS_NMI_WATCHDOG
tracing: Fix recursive user stack trace
perf,hw_breakpoint: Initialize hardware api earlier
x86: Ignore trap bits on single step exceptions
tracing: Force arch_local_irq_* notrace for paravirt
tracing: Fix module use of trace_bprintk()
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: fix build for PROC_FS disabled
block: fix amiga and atari floppy driver compile warning
blk-throttle: Fix calculation of max number of WRITES to be dispatched
ioprio: grab rcu_read_lock in sys_ioprio_{set,get}()
xen/blkfront: cope with backend that fail empty BLKIF_OP_WRITE_BARRIER requests
xen/blkfront: Implement FUA with BLKIF_OP_WRITE_BARRIER
xen/blkfront: change blk_shadow.request to proper pointer
xen/blkfront: map REQ_FLUSH into a full barrier
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
nilfs2: fix typo in comment of nilfs_dat_move function
nilfs2: nilfs_iget_for_gc() returns ERR_PTR
Tool developers have to fill in a 'perf_event_ops' method table to
specify how to handle each event, so far the ones that were not
explicitely especified would get a stub that would just discard the
event.
Change that so that tool developers can get the lost event details and
the total number of such events at the end of 'perf report -D' output.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Collecting build-ids for long running sessions may take a long time
because it needs to traverse the whole just collected perf.data stream
of events, marking the DSOs that had hits and then looking for the
.note.gnu.build-id ELF section.
For things like the 'trace' tool that records and right away consumes
the data on systems where its unlikely that the DSOs being monitored
will change while 'trace' runs, it is desirable to remove build id
collection, so add a -B/--no-buildid option to perf record to allow such
use case.
Longer term we'll avoid all this if we, at DSO load time, in the kernel,
take advantage of this slow code path to collect the build-id and stash
it somewhere, so that we can insert it in the PERF_RECORD_MMAP event.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Remove knowledge of the 2-level wrapping in pgd_free(), and use the
pXd_none_or_clear_bad() macros when checking the entries.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than passing the pte value to __pte_error, pass the raw pte_t
cookie instead. Do the same for pmd and pgd functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
