The perf_swevent_enabled[] array has PERF_COUNT_SW_MAX elements.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20101024195041.GT5985@bicker>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The Wetab tablet dual-touch controller works the same way as the one
in the Joojoo tablet. This patch adds the Wetab to the list of
supported devices, and grabs it accordingly in hid-core.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
The firmware in the joojoo reports touches sequentially, one per
report, which confuses the current driver. A further complication is
the absense of any indication of a touch frame. This patch converts
the driver to the MT slots protocol, and outputs one full touch frame
per report. This way, proper handling for both firmwares is ensured.
Tested-by: Philipp Merkel <mail@philmerk.de>
Cc: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Use estimated signal-to-noise ratios to reduce noise and limit the
amount of events emitted.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
The firmware reports a logical minimum of one, but in order for
userspace applications to correctly map all reported values to
non-zero pressure, the driver needs to report a logical minimum of
zero. Fixed with this patch.
Tested-by: Philipp Merkel <mail@philmerk.de>
Cc: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
The firmware of both supported devices report a X/Y maximum of 4095,
whereas in reality, it is eight times larger. Fixed with this patch.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
The hid core does not yet handle input filtering. Take over the setup
of the input device, so that proper signal-to-noise ratios can be
used.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Touch devices capable of hovering, i.e., fingers detected a
distance from the surface, are not supported by the current
input MT protocol. This patch adds ABS_MT_DISTANCE, which may
be used to indicate the distance between the contact and the
surface.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
The drivers using the type B protocol all report tracking information
the same way. The contact id is semantically equivalent to
ABS_MT_SLOT, and the handling of ABS_MT_TRACKING_ID only complicates
the driver. The situation can be improved upon by providing a common
pointer emulation code, thereby removing the need for the tracking id
in the driver. This patch moves all tracking event handling over to
the input core, simplifying both the existing drivers and the ones
currently in preparation.
Acked-by: Ping Cheng <pingc@wacom.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
The MT slots devices all follow the same initialization pattern
of creating slots and hinting about buffer size. Let drivers call
an initialization function instead, and make sure it can be called
repeatedly without side effects.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
In preparation for common code to handle a larger set of MT slots
devices, move the slots handling over to a separate file.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
When we set/clear the dyn_features for an inode we hold the ip_lock.
So do it when we set/clear OCFS2_INDEXED_DIR_FL also.
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
This patch introduces support for Sitronix ST1232 integrated capacitive
touchscreen with LCD module. The touchscreen is multitouch capable and
can report coordinates of up to two contact points.
Signed-off-by: Tony SIM <chinyeow.sim.xt@renesas.com>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Two x86 patches broke lguest:
1) v2.6.35-492-g72d7c3b, which changed x86 to use the memblock allocator.
In lguest, the host places linear page tables at the top of mem, which
used to be enough to get us up to the swapper_pg_dir page tables. With
the first patch, the direct mapping tables used that memory:
Before: kernel direct mapping tables up to 4000000 @ 7000-1a000
After: kernel direct mapping tables up to 4000000 @ 3fed000-4000000
I initially fixed this by lying about the amount of memory we had, so
the kernel wouldn't blatt the lguest boot pagetables (yuk!), but then...
2) v2.6.36-rc8-54-gb40827f, which made x86 boot use initial_page_table.
This was initialized in a part of head_32.S which isn't executed by
lguest; it is then copied into swapper_pg_dir. So we have to initialize
it; and anyway we switch to it before we blatt the old tables, so that
fixes the previous damage as well.
For the moment, I cut & pasted the code into lguest's boot code, but
next merge window I will merge them.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
To: x86@kernel.org
lguest is dumb and drops *all* the pagetables for set_pte (which is
only used for kernel mapping manipulation, so it's OK without highmem).
But it's used a lot in boot, too. As a guest optimization, we
suppressed this flushing until the first page switch. Now we have
initial_page_table, that happens much earlier, so extend the heuristic
to wait until we switch to something other than the swapper_pg_dir or
initial_page_table.
As measured on my laptop under kvm, this dropped the time-to-mount-root
from 48 seconds to 4.3 seconds.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
fe25c7fc2e "x86: lguest: Convert to new irq chip functions" converted
enable_lguest_irq() to take a struct irq_data *, but didn't fix the one
internal caller.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
To: x86@kernel.org
Define all IRQs in irqs.h. If some IRQs are sharing one IRQ number, define
them together. If some IRQs are sharing same name with different IRQ number,
define different IRQ.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
After introducing pxa930/pxa935 and new silicons, original cpuid rules
of XScale generation 3 can't fit new silicons. Now redefine the rule
of PXA3xx.
Only PXA300/PXA310/PXA320/PXA930/PXA935 are family members of PXA3xx.
PXA930/PXA935 are family members of PXA93x. PXA93x can be considered
as PXA3xx + CP.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This is important because on PXA3xx, the physical mapping of SMEMC registers
differs from the one on PXA2xx. In order to get PCMCIA working on both PXA2xx
and PXA320, the PCMCIA driver was adjusted accordingly as well.
Also, various places in the kernel had to be patched to use
__raw_read/__raw_write.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch introduces pxa2xx_map_io() and pxa3xx_map_io() to distinguish
between PXA25x/PXA27x and PXA3xx memory mapping.
Also, fixup for platforms broken after introducing pxa{25x,27x}_map_io()
and pxa3xx_map_io() is included.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The camera registers start and range are encoded into the platform
device, and are actually handled by ioremap()'ed, thus the mapping
in pxa_map_io() is not necessary.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
On 2.6.37-rc1, garbage collection ioctl of nilfs was broken due to the
commit 263d90cefc ("nilfs2: remove own inode hash used for GC"),
and leading to filesystem corruption.
The patch doesn't queue gc-inodes for log writer if they are reused
through the vfs inode cache. Here, gc-inode is the inode which
buffers blocks to be relocated on GC. That patch queues gc-inodes in
nilfs_init_gcinode() function, but this function is not called when
they don't have I_NEW flag. Thus, some of live blocks are wrongly
overrode without being moved to new logs.
This resolves the problem by moving the gc-inode queueing to an outer
function to ensure it's done right.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
The user buffer may be 512-byte aligned, not page-aligned. We were
assuming the buffer was page-aligned and only accounting for
non-page-aligned io offsets.
Signed-off-by: Henry C Chang <henry_c_chang@tcloudcomputing.com>
Signed-off-by: Sage Weil <sage@newdream.net>
Make sure vram changes hit memory. This mirrors the
6xx/7xx behavior.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are too many strange corner cases triggered in old userspace
drivers out there to that it's nearly impossible to not break some
obscure app.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Seems to cause problems on certain laptops
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=24462
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-fixes' of /ssd/git/drm-next:
drm/i915/bios: Reverse order of 100/120 Mhz SSC clocks
agp/intel: Fix missed cached memory flags setting in i965_write_entry()
drm/i915/sdvo: Only use the SDVO pin if it is in the valid range
drm/i915/ringbuffer: Handle wrapping of the autoreported HEAD
drm/i915/dp: Fix I2C/EDID handling with active DisplayPort to DVI converter
If swap is on a UAS device, we could recurse into the driver by using
GFP_KERNEL. Using GFP_NOIO ensures we won't.
Reported-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While all existing UAS devices use alternate interface 1, this is not
guaranteed, and it has caused confusion with people trying to bind the
uas driver to non-uas devices.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The spec calls this the status pipe. While it is used to receive sense IUs,
it is also used to receive other IUs, so this can be confusing.
Reported-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The IUs are not being fully initialised by the driver (due to the reserved
space). Since we should be zeroing reserved fields, use kzalloc to do
it for us.
Reported-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a comment to the Sense IU data structure that it's also used for Read
Ready and Write Ready. Remove the 'service response' element since it's
gone from the current draft (04).
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial framebuffer components. Add board-trout-panel.c
as well as platform parts to enable the framebuffer. This
code comes directly from Google's tree.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
CLK_MINMAX is used to denote clocks that have a wide variation
in possible frequencies. This handling just sets the min and
max values to the same value.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
