Some bad interaction between the idle and the suspend paths has been
identified: the idle code is called during the suspend enter and exit
sequences. This could cause corruption or lock-up of resources.
The solution is to move the calls to disable_hlt at the very beginning
of the suspend sequence (ex. in omap3_pm_begin instead of
omap3_pm_prepare), and the call to enable_hlt at the very end of
the suspend sequence (ex. in omap3_pm_end instead of omap3_pm_finish).
Tested with RET and OFF on Beagle and OMAP3EVM.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Program adapter's StationAddress register when changing device MAC address
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrap up acceess to ASICCtrl high word with a macro
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the libdwfl library before 0.148 fails to analyze live kernel debuginfo,
'perf probe --list' compiled with those old libdwfl sometimes crashes.
To avoid that bug, perf probe does not use libdwfl's live kernel analysis
routine when it is compiled with older libdwfl.
Side effect: perf with older libdwfl doesn't support listing probe in modules
with source code line. Those could be shown by symbol+offset.
Cc: 2nddept-manager@sdl.hitachi.co.jp
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <20101217131218.24123.62424.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This function has three bugs:
1) The offset should be valid most of the time, this is just
a sanity check, therefore we should use "likely" not "unlikely"
2) This is the only place where we can check for arithmetic overflow
of the pointer plus the length.
3) The existing range checks are off by one, the valid range is
skb->head to skb_tail_pointer(), inclusive.
Based almost entirely upon a patch by Ralph Loader.
Reported-by: Ralph Loader <suckfish@ihug.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can translate pseudo load instructions at filter check time to
dedicated instructions to speed up filtering and avoid one switch().
libpcap currently uses SKF_AD_PROTOCOL, but custom filters probably use
other ancillary accesses.
Note : I made the assertion that ancillary data was always accessed with
BPF_LD|BPF_?|BPF_ABS instructions, not with BPF_LD|BPF_?|BPF_IND ones
(offset given by K constant, not by K + X register)
On x86_64, this saves a few bytes of text :
# size net/core/filter.o.*
text data bss dec hex filename
4864 0 0 4864 1300 net/core/filter.o.new
4944 0 0 4944 1350 net/core/filter.o.old
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael pointed out that bnx2_close() already cancels bp->reset_task
and thus it is guaranteed to be idle when bnx2_remove_one() is called.
Remove the unnecessary cancel_work_sync() in remove_one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The calculations done with sync_clk are anyway in picoseconds
and switching to picoseconds allows sync_clk values that are
not a whole number of nanoseconds - which is sometimes the
case.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In the error-path where PM notifies PM_POST_RESTORE, the rescan-blockage
should be cleared as well. Otherwise it'll be never re-probed.
Also, as a bonus, this fixes a bug in S4 with user-mode suspend in the
current code, as it sends PM_POST_RESTORE instead of
PM_POST_HIBERNATION wrongly.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Based on report made by Yauhen in:
"MMC: Fix multiblock SDIO transfers in AT91 MCI" patch,
I report those changes to the brother driver: atmel-mci.
So, this patch sets SDIO transfer types: SDIO block and SDIO byte
transfers instead of using ordinary MMC block transfers.
It is checking opcode for SDIO CMD53 and setting transfer
type in MCI_CMDR register properly.
Reported-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
Cc: <stable@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The AT91 MCI has special SDIO transfer types: SDIO block and SDIO byte
transfers, but at91_mci driver doesn't use them and handles all SDIO
transfers as ordinary MMC block transfers. This causes problems for
multiple-block SDIO transfers (in particular for 256-bytes blocks).
Fix this situation by checking the opcode for SDIO CMD53 and setting
the transfer type in the AT91_MCI_CMDR register properly.
This patch was tested with libertas SDIO driver: problem with TX
timeouts on big packets was eliminated.
Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
Cc: <stable@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The original code had a several problems:
*) It had potential null dereferences of "priv" and "res".
*) It released the memory region before it was aquired.
*) It didn't free "ndev" after it was allocated.
*) It didn't call unregister_netdev() after calling stmmac_probe().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We dereferenced params on the line before so it's too late to check if
params is NULL. In fact, params can never be NULL and strict_cos is
either 0 or 1 so that part of the check is bogus too. Let's remove it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Le vendredi 17 décembre 2010 à 10:26 +0100, Eric Dumazet a écrit :
>
> I think we can add this after latest Changli patch :
>
> He does one skb_clone() before calling the sniffers.
> We could set timestamp on this clone, instead of original skb.
>
> Problem solved.
>
[PATCH net-next-2.6] net: timestamp cloned packet in dev_queue_xmit_nit
Now we do one clone of skb if at least one sniffer might take packet,
we also can do the skb timestamping on the clone and let original packet
unchanged.
This is a generalization of commit 8caf153974 (net: sch_netem: Fix an
inconsistency in ingress netem timestamps.)
This way, we can have a good idea when packets are delivered to our
stack (tcpdump -i ifb0), while a tcpdump on original device gives
timestamps right before ingressing.
This also speedup our stack, avoiding taking timestamps if not needed.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Changli Gao <xiaosuo@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a handful of missing CDBs defs that are used by TCM
persistent reservation logic in the SPC-4 defined CDB exclusion table for
registrations and reservations.
This includes a number of missing MI_* and MO_* prefixed service actions defs
for MAINTENANCE_IN and MAINTENANCE_OUT that are mentioned wrt to persistent
registration and reservation status for the SCSI Initiator Port.
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch updates the GPL headers in megaraid_sas_base.c and megaraid_sas.h.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch renames megaraid_sas.c to megaraid_sas_base.c to facilitate
other files in the compile.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
It seems that zero should be returned if scsi_target_is_busy(starget) is
true, no matter if sdev is on the starved list.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently, when scsi_dh_activate() returns with an error
(e.g. SCSI_DH_NOSYS) the activate_complete callback is not called and
the error is not propagated to DM mpath.
When a SCSI device attached to a device handler is deleted, userland
processes currently performing I/O on the device will have their I/O
hang forever.
- Set SCSI_DH_NOSYS error when the handler is in the process of being
deleted (e.g. the SCSI device is in a SDEV_CANCEL or SDEV_DEL state).
- Set SCSI_DH_DEV_OFFLINED error when device is in SDEV_OFFLINE state.
- Call the activate_complete callback function directly from
scsi_dh_activate if an error has been set (when either the scsi_dh
internal data has already been deleted or is in the process of being
deleted).
The patch was tested in an iSCSI environment, RDAC H/W handler and
multipath. In the following reproduction process, dd will I/O hang
forever and the only way to release it will be to reboot the machine:
1) Perform I/O on a multipath device:
dd if=/dev/dm-0 of=/dev/zero bs=8k count=1000000 &
2) Delete all slave SCSI devices contained in the mpath device:
I) In an iSCSI environment, the easiest way to do this is by
stopping iSCSI:
/etc/init.d/iscsi stop
II) Another way to delete the devices is by applying the following
bash scriptlet:
dm_devs=$(ls /sys/block/ | grep dm- | xargs)
for dm_dev in $dm_devs; do
devices=$(ls /sys/block/$dm_dev/slaves)
for device in $devices; do
echo 1 > /sys/block/$device/device/delete
done
done
NOTE: when DM mpath's fail_path uses blk_abort_queue this scsi_dh change
isn't strictly required. However, DM mpath's call to blk_abort_queue
will soon be reverted because it has proven to be unsafe due to a race
(between blk_abort_queue and scsi_request_fn) that can lead to list
corruption. Therefore we cannot rely on blk_abort_queue via fail_path,
but even if we could this scsi_dh change is still preferrable.
Signed-off-by: Menny Hamburger <Menny_Hamburger@Dell.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Otherwise, after doing a RAID level migration, the disk will be
disruptively removed and re-added as a different disk on rescan.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The firmware may have been updated, in which case, it's the same device,
and in that case, we do not want to remove and add the device, we want to
let it continue as is.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Updated commands used for ELS to utilize VPI
Allocate RPI at node creation time and pass in ELS commnads.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Implement new SLI4 init procedures based on if_type:
- Add structure changes for new SLIPORT registers and BAR changes.
- Update register names to be consistent with inteface spec terms.
- Added union to encapsulate Hardward error registers.
- Rework lpfc_sli4_post_status_check() around SLI-4's SLI_INTF type
- Removed the lpfc_sli4_fw_cfg_check routine
- Segmented driver logic to include evaluation of the if_type to
engage different behaviors.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Implement the FC and SLI async event handlers:
- Updated MQ_CREATE_EXT mailbox structure to include fc and SLI async events.
- Added the SLI trailer code.
- Split physical field into type and number to reflect latest SLI spec.
- Changed lpfc_acqe_fcoe to lpfc_acqe_fip to reflect latest Spec changes.
- Added lpfc_acqe_fc_la structure for FC link attention async events.
- Added lpfc_acqe_sli structure for sli async events.
- Added lpfc_sli4_async_fc_evt routine to handle fc la async events.
- Added lpfc_sli4_async_sli routine to handle sli async events.
- Moved LPFC_TRAILER_CODE_FC to be handled by its own handler function.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Use for iocbq->context1 to hold the ndlp pointer.
- Set ndlp in all iocbs generated from ioctl functions.
- Turn parity and serr bits back on after performing sli4 board reset.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix iotag handling:
1) Update and check io tag for retry case.
2) Clearing upper 3 bits in io tag when an IO completes.
The 3 upper bits in io tags are used for counting FCP exchange retry.
Un-cleared bits will cause firmware to access invalid memory when the
same io tag is used for an IO to a target that doesn't support FCP
exchange retry.
3) Only check the effective bits when validating an iotag.
Other minor fixes:
1) Added trace to get FC header type with assert of unhandled packet received.
Ignore the type FC_TYPE_FC_FSS (FC_XS).
2) Fixed the adapter info display check - to check for fcmode flag even.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Direct attach is not working due to the check of PID in fcxp_send request.
- Added logic to set the lps->lp_pid with the PID assigned for n2n mode.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Made IOC auto_recovery synchronized and not timer based.
- Only one PCI function will attempt to recover and reinitialize
the ASIC on a failure, after all the active PCI fns
acknowledge the IOC failure.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the bfa driver is loaded a flogi is sent without the knowledge of
trunking configuration. This normal flogi causes the switch ports
which had trunking enabled to go to persistent offline. Solution is
to store the port configuration (which has trunking info) in the flash
for persistency. The firmware will read this configuration when the
very first fcport enable is received.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Move fw trace save logic to bfa_ioc_sm_fail_entry(),
so that fw trace is saved irrespective of the cause of the failure.
- Make bfa_ioc_sm_fail() a failure parking state.
- Rename bfa_ioc_sm_initfail() to a more appropriate bfa_ioc_sm_fail_retry()
as it is no longer a parking state.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove OS wrapper functions/macros, and as a result remove bfa_os_inc.h.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove SCSI IO callbacks, and as a result remove bfa_cb_ioim.h.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Modified scatter gather processing to use the kernel provided
scsi_for_each_sg() macro.
1) Instead of allocating and setting up sgpg in bfa_ioim_sge_setup(),
we only do allocation. As a result, we remove
bfa_ioim_sgpg_setup() and rename bfa_ioim_sge_setup() to
bfa_ioim_sgpg_alloc().
2) bfa_ioim_send_ioreq() call scsi_for_each_sg() to handle both inline
and sgpg setup.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Cleaned up one line functions.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
By changing field ordering we can avoid a couple of memory holes in
the tables that use the ibmvfc_async_desc structure.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Since iscsi transport can be built as a module and uses netlink socket
to communicate. The module should have an alias to autoload when socket
of NETLINK_ISCSI type is requested.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The zfcpdump tool requires a method to attach exactly one LUN. The
easiest way to achieve this is to add a new zfcp module parameter.
When allow_lun_scan is set to "false", zfcp only accepts LUNs that
have been configured through the unit_add sysfs interface.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The function zfcp_cache_hw_align is only called from zfcp_module_init,
so it should be declared with __init as well.
Reviewed-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
