Currently, mac80211 always advertises that it may send
up to 64 subframes in an aggregate. This is fine, since
it's the max, but might as well be set to zero instead
since it doesn't have any information.
However, drivers might have that information, so allow
them to set a variable giving it, which will then be
used. The default of zero will be fine since to the
peer that means we don't know and it will just use its
own limit for the buffer size.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The aggregation code currently doesn't implement the
buffer size negotiation. It will always request a max
buffer size (which is fine, if a little pointless, as
the mac80211 code doesn't know and might just use 0
instead), but if the peer requests a smaller size it
isn't possible to honour this request.
In order to fix this, look at the buffer size in the
addBA response frame, keep track of it and pass it to
the driver in the ampdu_action callback when called
with the IEEE80211_AMPDU_TX_OPERATIONAL action. That
way the driver can limit the number of subframes in
aggregates appropriately.
Note that this doesn't fix any drivers apart from the
addition of the new argument -- they all need to be
updated separately to use this variable!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mesh is disabled, mac80211 was returning
beacons with an empty mesh ID. That isn't
desirable, even if drivers shouldn't be trying
to get beacons to start with.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using a mixture of AP and Station interfaces,
the hardware mode was using the type of the
last VIF registered. Instead, we should keep track
of the number of different types of vifs and set the
mode accordingly.
In addtion, use the vif type instead of hardware opmode
when dealing with beacons.
Attempt to move some of the common setup code into smaller
methods so we can re-use it when changing vif mode as
well as adding/deleting vifs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because the sendbar variable was not reset to zero, the stack would send
Block ACK requests for all subframes following the one that failed, which
could mess up the receiver side block ack window.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes the first TID in the first AC's list is not available for forming
a new aggregate (the BAW might not allow it), however other TIDs may have
data available for sending.
Prevent a slowdown of other TIDs by going through multiple entries until
we've either hit the last one or enough AMPDUs are pending in the hardware
queue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9285 carrier leakage calibration related workaround on high
temperature is not applicable for AR9271.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k_hw assumes that caldata is valid only for
oper channel. But with ath9k_htc case, the caldata is
passed for all channels on hw_reset though we are not doing
calibration on that channel. So the oper channel's nf history
got cleared to default due to mismatch in channel flags.
This patch also saves some space.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
caldata's channel info is never filled with operating channel
info which is causing the operating channel's noise floor
history buffer is reset to default nf during channel change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mppath is mesh related parameter and maybe unused
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rx error bit parsing was changed to consider PHY errors and various
decryption errors separately. While correct according to the documentation,
this is causing spurious decryption error reports in some situations.
Fix this by restoring the original order of the checks in those places,
where the errors are meant to be mutually exclusive.
If a CRC error is reported, then MIC failure and decryption errors
are irrelevant, and a PHY error is unlikely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices don't support the maximum AMDPU buffer size of 64, so we
need to add an option to configure this in the hardware configuration.
This value will be used in the ADDBA response instead of the value
suggested in the request, if the latter is greater than the max
supported.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Tested-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace MESH_WORK_GROW_MPATH_TABLE by MESH_WORK_GROW_MPP_TABLE in
mesh_mpp_table_grow call condition.
(Clearly the original was a typo... -- JWL)
Signed-off-by: Nickolay Ledovskikh <nledovskikh@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eeprom read functions are of bool type and not int.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since baseband hangs are rare, but the hang check function has a high
false positive rate in some situations, we need to add more reliable
indicators.
In AP mode we can use blocked beacon transmissions as an indicator,
they should be rare enough.
In station mode, we can skip the hang check entirely, since a true
hang will trigger beacon loss detection, and mac80211 will rescan,
which leads to a hw reset that will bring the hardware back to life.
To make this more reliable, we need to skip fast channel changes
if the hardware appears to be stuck.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There might be some old stale data left, which could confuse tracking
of pending tx frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txtid->seq_start may not always be up to date, when there is HT non-AMPDU
traffic just before starting an AMPDU session. Relying on txtid->seq_next
is better, since it is also used to generate the sequence numbers for
all QoS data frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a tid pointer is passed to ath_tx_send_normal(), it increases the
starting sequence number for the next AMPDU action frame, which should
only be done if the sequence number assignment is fresh. In this case
it is clearly not.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Basically fix and fine-tune RT3070/RT3071/RT3090 chip RF initial value
when call rt2800_init_rfcsr
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCI/PCIE radio off behavior is different from SOC/USB.
They mainly use MCU command to disable DMA, TX/RX and enter power saving mode.
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrote code for checking if the destination is proxied by a mesh portal, to facilitate better
understanding of the functionality.
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Acked-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For USB devices, reading the EEPROM data can be offloaded
to the target. Use multiple register reads to take advantage
of this feature to reduce initialization time.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This would decrease latency in reading bulk registers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
set_key callback is defined for mac80211 to install keys for HW crypto in AP
mode. Driver currently falls back to SW crypto in STA mode. Add support to
configure the keys appropriately in the hardware after the set_key routine is
called.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hw crypto is enabled, set rx status flags appropriately depending on
whether hw crypto is enabled for a particular bss.
Also report MIC errors to mac80211, so that counter measures can be
initiated
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: yogesh powar <yogeshp@marvell.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Different tail pads will be needed for crypto depending on the crypto
mode. Add support to encapsulate the packets with appropriate pad
value.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add capability to add_dma_header to support padding at tail of the data
packet to be transmitted when crypto is enabled. Padding is required for
adding crypto information in data packets for supporting 802.11 security
modes.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sound/pci/hda/patch_realtek.c: In function ‘alc_apply_fixup’:
sound/pci/hda/patch_realtek.c:1724:14: warning: unused variable ‘modelname’
snd_printdd() is evaluated only when CONFIG_SND_DEBUG_VERBOSE=y.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit a4f740cf, "of/flattree: Add of_flat_dt_match() helper function"
introduced build failures in arch/powerpc/platform/83xx by mistyping
'static' as 'struct' in the compatible string list, and omitting a few
semicolons. This patch fixes it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds flow-based timestamping for conntracks. This
conntrack extension is disabled by default. Basically, we use
two 64-bits variables to store the creation timestamp once the
conntrack has been confirmed and the other to store the deletion
time. This extension is disabled by default, to enable it, you
have to:
echo 1 > /proc/sys/net/netfilter/nf_conntrack_timestamp
This patch allows to save memory for user-space flow-based
loogers such as ulogd2. In short, ulogd2 does not need to
keep a hashtable with the conntrack in user-space to know
when they were created and destroyed, instead we use the
kernel timestamp. If we want to have a sane IPFIX implementation
in user-space, this nanosecs resolution timestamps are also
useful. Other custom user-space applications can benefit from
this via libnetfilter_conntrack.
This patch modifies the /proc output to display the delta time
in seconds since the flow start. You can also obtain the
flow-start date by means of the conntrack-tools.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
When the lirc drivers were converted over to using memdup_user, I
mistakenly also removed corresponding calls to kfree. Add those back. I
also screwed up on the allocation error check in lirc_serial, using if
(PTR_ERR()) instead of if (IS_ERR()), which broke transmit.
Reported-by: Jiri Fojtasek <jiri.fojtasek@hlohovec.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current hdpvr code kmalloc's a new buffer for every i2c read and
write. Rather than do that, lets allocate a buffer in the driver's
device struct and just use that every time.
The size I've chosen for the buffer is the maximum size I could
ascertain might be used by either ir-kbd-i2c or lirc_zilog, plus a bit
of padding (lirc_zilog may use up to 100 bytes on tx, rounded that up
to 128).
Note that this might also remedy user reports of very sluggish behavior
of IR receive with hdpvr hardware.
v2: make sure (len <= (dev->i2c_buf)) [Jean Delvare]
Reported-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of things going on here, but the end result is that the IR part
on the hdpvr gets enabled, and can be used with ir-kbd-i2c and/or
lirc_zilog.
First up, there are some conditional build fixes that come into play
whether i2c is built-in or modular. Second, we're swapping out
i2c_new_probed_device() for i2c_new_device(), as in my testing, probing
always fails, but we *know* that all hdpvr devices have a z8 chip at
0x70 and 0x71. Third, we're poking at an i2c address directly without a
client, and writing some magic bits to actually turn on this IR part
(this could use some improvement in the future). Fourth, some of the
i2c_adapter storage has been reworked, as the existing implementation
used to lead to an oops following i2c changes c. 2.6.31.
Earlier editions of this patch have been floating around the 'net for a
while, including being patched into Fedora kernels, and they *do* work.
This specific version isn't yet tested, beyond loading ir-kbd-i2c and
confirming that it does bind to the RX address of the hdpvr.
[mchehab@redhat.com: I2C_CLASS_TV_ANALOG is not defined. Fix compilation bug]
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes an egregious bug in mceusb driver, where the receiver was being
put into idle mode far sooner than it should have, thanks to storing a
timeout value that in us where it should be ns. Basically, the receiver
kept going into idle mode before a trailing space had been fully
received, which was causing problems for some protocols, most notably
manifesting as lirc userspace never receiving a trailing space for any
rc5 signals.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a bug in v4l2_device_unregister where the sd pointer can be dereferenced
after it was freed.
Normally the i2c adapter is removed before this function is called. Removing
the adapter will also unregister all subdevs on that adapter, so generally
v4l2_device_unregister has nothing to do. However, in the case of a platform
i2c bus that bus is generally not freed.
In that case, after freeing the i2c subdevice the code will fall into the
second block when it tests if the subdev is a SPI device. But by that time
the subdev is already freed and the kernel oopses.
The fix is trivial: continue with the loop after freeing the i2c or spi
subdevice.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Zeroing video_device.dev causes a memory leak if video_set_drvdata
was called before video_register_device was called. video_set_drvdata
calls dev_set_drvdata which allocates video_device.dev.p.
memsetting this will prevent freeing of that memory.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After a detach zero the whole device state to ensure a clean slate
on the next attach.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_queryctrl sets the step value based on the control type. That would
be fine if it used the control type stored in the V4L2 kernel control
object, not the one stored in the userspace ioctl structure that has
just been memset to 0. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The later makes extensive use of structures defined in the former.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When queryctrl is called with a V4L2_CID_PRIVATE_BASE control ID, then
currently it is replaced by the real internal ID. This is not according to
the spec so keep the V4L2_CID_PRIVATE_BASE ID in this case.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_S_CTRL did not check against read-only controls. Even worse, for
controls of type CTRL_CLASS it would cause a kernel oops since those controls
do not have a s_ctrl op.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When registering an IR Rx device with the I2C subsystem, provide more detailed
information about the IR device and default remote configuration for the IR
driver modules.
Also explicitly register any IR Tx device with the I2C subsystem.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts a portion of commit
44243fc2ef
A commit for which I errantly recommended that defaults for I2C address
0x71 not be set by ir-kbd-i2c.c
The pvrusb2 and bttv drivers currently rely on ir-kbd-i2c setting
defaults for that address. Until I can get those bridge drivers fixed
to properly send IR_i2c_init_data for boards with Zilog Z8 chips,
just add back the default settings for I2C address 0x71.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
