Use the NAND core helper function nand_ecc_choose_conf to tune
the ECC parameters instead of the function locally defined.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
commit 2c8f8afa7f ("mtd: nand: add generic helpers to check,
match, maximize ECC settings") provides generic helpers which
drivers can use for setting up ECC parameters.
Since same board can have different ECC strength nand chips so
following is the logic for setting up ECC strength and ECC step
size, which can be used by most of the drivers.
1. If both ECC step size and ECC strength are already set
(usually by DT) then just check whether this setting
is supported by NAND controller.
2. If NAND_ECC_MAXIMIZE is set, then select maximum ECC strength
supported by NAND controller.
3. Otherwise, try to match the ECC step size and ECC strength closest
to the chip's requirement. If available OOB size can't fit the chip
requirement then select maximum ECC strength which can be fit with
available OOB size.
This patch introduces nand_ecc_choose_conf function which calls the
required helper functions for the above logic. The drivers can use
this single function instead of calling the 3 helper functions
individually.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Pull devfreq fixes and documentation updates for v4.19 from MyungJoo Ham.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mzx/devfreq:
PM / devfreq: rk3399_dmc: Fix duplicated opp table on reload.
PM / devfreq: Init user limits from OPP limits, not viceversa
PM / devfreq: rk3399_dmc: fix spelling mistakes.
PM / devfreq: rk3399_dmc: do not print error when get supply and clk defer.
dt-bindings: devfreq: rk3399_dmc: move interrupts to be optional.
PM / devfreq: rk3399_dmc: remove wait for dcf irq event.
dt-bindings: clock: add rk3399 DDR3 standard speed bins.
dt-bindings: devfreq: rk3399_dmc: improve binding documentation.
PM / devfreq: use put_device() instead of kfree()
PM / devfreq: exynos-ppmu: Delete an error message for a failed memory allocation in exynos_ppmu_probe()
Detect and report the etoken facility. With spectre_v2=auto or
CONFIG_EXPOLINE_AUTO=y automatically disable expolines and use
the full branch prediction mode for the kernel.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
snd_pcm_lib_mmap_vmalloc() was supposed to be implemented with
somewhat special for vmalloc handling, but in the end, this turned to
just the default handler, i.e. NULL. As the situation has never
changed over decades, let's rip it off.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A VM which has:
- a DMA capable device passed through to it (eg. network card);
- running a malicious kernel that ignores H_PUT_TCE failure;
- capability of using IOMMU pages bigger that physical pages
can create an IOMMU mapping that exposes (for example) 16MB of
the host physical memory to the device when only 64K was allocated to the VM.
The remaining 16MB - 64K will be some other content of host memory, possibly
including pages of the VM, but also pages of host kernel memory, host
programs or other VMs.
The attacking VM does not control the location of the page it can map,
and is only allowed to map as many pages as it has pages of RAM.
We already have a check in drivers/vfio/vfio_iommu_spapr_tce.c that
an IOMMU page is contained in the physical page so the PCI hardware won't
get access to unassigned host memory; however this check is missing in
the KVM fastpath (H_PUT_TCE accelerated code). We were lucky so far and
did not hit this yet as the very first time when the mapping happens
we do not have tbl::it_userspace allocated yet and fall back to
the userspace which in turn calls VFIO IOMMU driver, this fails and
the guest does not retry,
This stores the smallest preregistered page size in the preregistered
region descriptor and changes the mm_iommu_xxx API to check this against
the IOMMU page size.
This calculates maximum page size as a minimum of the natural region
alignment and compound page size. For the page shift this uses the shift
returned by find_linux_pte() which indicates how the page is mapped to
the current userspace - if the page is huge and this is not a zero, then
it is a leaf pte and the page is mapped within the range.
Fixes: 121f80ba68 ("KVM: PPC: VFIO: Add in-kernel acceleration for VFIO")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The size is always equal to 1 page so let's use this. Later on this will
be used for other checks which use page shifts to check the granularity
of access.
This should cause no behavioral change.
Cc: stable@vger.kernel.org # v4.12+
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This driver can spam the kernel log with multiple messages of:
net eth0: eth0: allmulti set
Usually 4 or 8 at a time (probably because of using ConnMan).
This message doesn't seem useful, so let's demote it from dev_info()
to dev_dbg().
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of in-kernel rawmidi buffers may be big up to 1MB, and it can
be specified freely by user-space; which implies that user-space may
trigger kmalloc() errors frequently.
This patch replaces the buffer allocation via kvmalloc() for dealing
with bigger buffers gracefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Don't call BATMAN_V experimental in Kconfig anymore, by Sven Eckelmann
- Enable DAT by default at compile time, by Antonio Quartulli
- Remove obsolete default n in Kconfig, by Sven Eckelmann
- Fix checkpatch spelling errors, by Sven Eckelmann
- Unify header guards style, by Sven Eckelmann
- Consolidate batadv_purge_orig functions, by Sven Eckelmann
- Replace type define with proper typedef, by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=dmZo
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20180717' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- Don't call BATMAN_V experimental in Kconfig anymore, by Sven Eckelmann
- Enable DAT by default at compile time, by Antonio Quartulli
- Remove obsolete default n in Kconfig, by Sven Eckelmann
- Fix checkpatch spelling errors, by Sven Eckelmann
- Unify header guards style, by Sven Eckelmann
- Consolidate batadv_purge_orig functions, by Sven Eckelmann
- Replace type define with proper typedef, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b6fb0df12d ("RDS/IB: Make ib_recv_refill return void") did
not change the comment accordingly.
Fixes: b6fb0df12d ("RDS/IB: Make ib_recv_refill return void")
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.ccom>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/dsa/rtl8366.c: In function ‘rtl8366_reset_vlan’:
drivers/net/dsa/rtl8366.c:234:25: warning: unused variable ‘vlan4k’ [-Wunused-variable]
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Söderlund says:
====================
ravb: small sparse fixes
This are fixes that have bugged me whenever I run sparse to check my own
changes to the driver. It's based on the latest net-next tree and tested
on M3-N.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong helper is used to swap the bytes when adding the lower bits of
the TX descriptors tag field in the shared ds_tagl variable. The
variable contains the DS[11:0] field and then the TAG[3:0] bits.
The mistake was highlighted by the sparse warning:
ravb_main.c:1622:31: left side has type restricted __le16
ravb_main.c:1622:31: right side has type unsigned short
ravb_main.c:1622:31: warning: invalid assignment: |=
ravb_main.c:1622:34: warning: cast to restricted __le16
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes sparse warning:
ravb_main.c:1257 ravb_get_strings() error: memcpy() '*ravb_gstrings_stats' too small (32 vs 960)
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inside a loop in ravb_get_ethtool_stats() a variable 'stats' is declared
resulting in the argument also named 'stats' to be shadowed. Fix this
warning by renaming the unused argument 'stats' to 'estats'.
This fixes the sparse warning:
ravb_main.c:1225:36: originally declared here
ravb_main.c:1233:41: warning: symbol 'stats' shadows an earlier one
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The constants are 64bit but not explicitly declared UL resulting
in sparse warnings. Fix this by declaring the constants UL.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The call to of_find_compatible_node() is returning a pointer with
incremented refcount so it must be explicitly decremented after the
last use. As here it is only being used for checking of node presence
but the result is not actually used in the success path it can be
dropped immediately.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: commit f725758b89 ("KVM: PPC: Book3S HV: Use OPAL XICS emulation on POWER9")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When attaching a hardware table to LIOBN in KVM, we match table parameters
such as page size, table offset and table size. However the tables are
created via very different paths - VFIO and KVM - and the VFIO path goes
through the platform code which has minimum TCE page size requirement
(which is 4K but since we allocate memory by pages and cannot avoid
alignment anyway, we align to 64k pages for powernv_defconfig).
So when we match the tables, one might be bigger that the other which
means the hardware table cannot get attached to LIOBN and DMA mapping
fails.
This removes the table size alignment from the guest visible table.
This does not affect the memory allocation which is still aligned -
kvmppc_tce_pages() takes care of this.
This relaxes the check we do when attaching tables to allow the hardware
table be bigger than the guest visible table.
Ideally we want the KVM table to cover the same space as the hardware
table does but since the hardware table may use multiple levels, and
all levels must use the same table size (IODA2 design), the area it can
actually cover might get very different from the window size which
the guest requested, even though the guest won't map it all.
Fixes: ca1fc489cf "KVM: PPC: Book3S: Allow backing bigger guest IOMMU pages with smaller physical pages"
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Originally PPC KVM MMIO emulation uses only 0~31#(5 bits) for VSR
reg number, and use mmio_vsx_tx_sx_enabled field together for
0~63# VSR regs.
Currently PPC KVM MMIO emulation is reimplemented with analyse_instr()
assistance. analyse_instr() returns 0~63 for VSR register number, so
it is not necessary to use additional mmio_vsx_tx_sx_enabled field
any more.
This patch extends related reg bits (expand io_gpr to u16 from u8
and use 6 bits for VSR reg#), so that mmio_vsx_tx_sx_enabled can
be removed.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The opp table is not removed when the driver is unloaded neither when
there is an error within probe, so if the driver is reloaded the opp
core shows the following warning:
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
200000000, volt: 900000, enabled: 1. New: freq: 200000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
400000000, volt: 900000, enabled: 1. New: freq: 400000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
666000000, volt: 900000, enabled: 1. New: freq: 666000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
800000000, volt: 900000, enabled: 1. New: freq: 800000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
928000000, volt: 900000, enabled: 1. New: freq: 928000000,
volt: 900000, enabled: 1
This patch fixes the error path in the probe function and adds a .remove
function to properly cleanup the opp table on unloading.
Fixes: 5a893e31a6 (PM / devfreq: rockchip: add devfreq driver for rk3399 dmc)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Commit ab8f58ad72 ("PM / devfreq: Set min/max_freq when adding
the devfreq device") introduced the initialization of the user
limits min/max_freq from the lowest/highest available OPPs. Later
commit f1d981eaec ("PM / devfreq: Use the available min/max
frequency") added scaling_min/max_freq, which actually represent
the frequencies of the lowest/highest available OPP. scaling_min/
max_freq are initialized with the values from min/max_freq, which
is totally correct in the context, but a bit awkward to read.
Swap the initialization and assign scaling_min/max_freq with the
OPP freqs and then the user limts min/max_freq with scaling_min/
max_freq.
Needless to say that this change is a NOP, intended to improve
readability.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Fix some spelling mistakes in error and debug messages.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
We just return -EPROBE_DEFER error code to caller and do not
print error message when try to get center logic regulator
and DMC clock defer.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
In ATF we already wait for DDR DVFS finish, so move the interrupts properties
to be optional.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
We have already wait dcf done in ATF, so don't need wait dcf irq
in kernel, besides, clear dcf irq in kernel will import competiton
between kernel and ATF, only handle dcf irq in ATF is a better way.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
DDR3 SDRAM Standard (JESD79-3F) defines some standard speed bins for
DDR3 memories. The rk3399_dmc driver allows you to pass these values via
the device tree. For that purpose the devfreq/rk3399_dmc.txt binding
refers to a ddr.h file which does not exist. This patch adds the missing
defines in a include file called rk3399-ddr.h with the definition of
standard speed bins according to the ARM Trusted Firmware (ATF).
Fixes: c1ceb8f7c1 (Documentation: bindings: add dt documentation for rk3399 dmc)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
There are several typos, references to non existent files, grammar and
punctuation mistakes in the rk3399_dmc.txt binding. This patch tries
to improve the binding documentation and fix these mistakes.
Signed-off-by: Nick Milner <nick.milner@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
- [1/5] Fix some attributes to match with the code s/_disb/_dis/
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Never directly free @dev after calling device_register() or
device_unregister(), even if device_register() returned an error.
Always use put_device() to give up the reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This adds the Ethernet and Realtek switch device to the
D-Link DIR-685 Gemini-based device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a driver core for the Realtek SMI chips and a
subdriver for the RTL8366RB. I just added this chip simply
because it is all I can test.
The code is a massaged variant of the code that has been
sitting out-of-tree in OpenWRT for years in the absence of
a proper switch subsystem. This creates a DSA driver for it.
I have tried to credit the original authors wherever
possible.
The main changes I've done from the OpenWRT code:
- Added an IRQ chip inside the RTL8366RB switch to demux and
handle the line state IRQs.
- Distributed the phy handling out to the PHY driver.
- Added some RTL8366RB code that was missing in the driver at
the time, such as setting up "green ethernet" with a funny
jam table and forcing MAC5 (the CPU port) into 1 GBit.
- Select jam table and add the default jam table from the
vendor driver, also for ASIC "version 0" if need be.
- Do not store jam tables in the device tree, store them
in the driver.
- Pick in the "initvals" jam tables from OpenWRT's driver
and make those get selected per compatible for the
whole system. It's apparently about electrical settings
for this system and whatnot, not really configuration
from device tree.
- Implemented LED control: beware of bugs because there are
no LEDs on the device I am using!
We do not implement custom DSA tags. This is explained in
a comment in the driver as well: this "tagging protocol" is
not simply a few extra bytes tagged on to the ethernet
frame as DSA is used to. Instead, enabling the CPU tags
will make the switch start talking Realtek RRCP internally.
For example a simple ping will make this kind of packets
appear inside the switch:
0000 ff ff ff ff ff ff bc ae c5 6b a8 3d 88 99 a2 00
0010 08 06 00 01 08 00 06 04 00 01 bc ae c5 6b a8 3d
0020 a9 fe 01 01 00 00 00 00 00 00 a9 fe 01 02 00 00
0030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
As you can see a custom "8899" tagged packet using the
protocol 0xa2. Norm RRCP appears to always have this
protocol set to 0x01 according to OpenRRCP. You can also
see that this is not a ping packet at all, instead the
switch is starting to talk network management issues
with the CPU port.
So for now custom "tagging" is disabled.
This was tested on the D-Link DIR-685 with initramfs and
OpenWRT userspaces and works fine on all the LAN ports
(lan0 .. lan3). The WAN port is yet not working.
Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: Roman Yeryomin <roman@advem.lv>
Cc: Colin Leitner <colin.leitner@googlemail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Realtek SMI family is a set of DSA chips that provide
switching in routers. This binding just follows the pattern
set by other switches but with the introduction of an embedded
irqchip to demux and handle the interrupts fired by the single
line from the chip.
This interrupt construction is similar to how we handle
interrupt controllers inside PCI bridges etc.
Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: Roman Yeryomin <roman@advem.lv>
Cc: Colin Leitner <colin.leitner@googlemail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8366RB is an ASIC with five internal PHYs for
LAN0..LAN3 and WAN. The PHYs are spawn off the main
device so they can be handled in a distributed manner
by the Realtek PHY driver. All that is really needed
is the power save feature enablement and letting the
PHY driver core pick up the IRQ from the switch chip.
Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: Roman Yeryomin <roman@advem.lv>
Cc: Colin Leitner <colin.leitner@googlemail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware_loader can be built as a loadable module, which now
fails when CONFIG_SECURITY is enabled, because a call to the
security_kernel_load_data() function got added, and this is
not exported to modules:
ERROR: "security_kernel_load_data" [drivers/base/firmware_loader/firmware_class.ko] undefined!
Add an EXPORT_SYMBOL_GPL() to make it available here.
Fixes: 6e852651f2 ("firmware: add call to LSM hook before firmware sysfs fallback")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: James Morris <james.morris@microsoft.com>
octeon_mgmt driver doesn't drop RX frames that are 1-4 bytes bigger than
MTU set for the corresponding interface. The problem is in the
AGL_GMX_RX0/1_FRM_MAX register setting, which should not account for VLAN
tagging.
According to Octeon HW manual:
"For tagged frames, MAX increases by four bytes for each VLAN found up to a
maximum of two VLANs, or MAX + 8 bytes."
OCTEON_FRAME_HEADER_LEN "define" is fine for ring buffer management, but
should not be used for AGL_GMX_RX0/1_FRM_MAX.
The problem could be easily reproduced using "ping" command. If affected
system has default MTU 1500, other host (having MTU >= 1504) can
successfully "ping" the affected system with payload size 1473-1476,
resulting in IP packets of size 1501-1504 accepted by the mgmt driver.
Fixed system still accepts IP packets of 1500 bytes even with VLAN tagging,
because the limits are lifted in HW as expected, for every VLAN tag.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
glibc uses a different defintion of sigset_t than the kernel does,
and the current version would pull in both. To fix this just do not
expose the type at all - this somewhat mirrors pselect() where we
do not even have a type for the magic sigmask argument, but just
use pointer arithmetics.
Fixes: 7a074e96 ("aio: implement io_pgetevents")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Adrian Reber <adrian@lisas.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Currently printing [hashed] pointers requires enough entropy to be
available. Early in the boot sequence this may not be the case
resulting in a dummy string '(____ptrval____)' being printed. This
makes debugging the early boot sequence difficult. We can relax the
requirement to use cryptographically secure hashing during debugging.
This enables debugging while keeping development/production kernel
behaviour the same.
If new command line option debug_boot_weak_hash is enabled use
cryptographically insecure hashing and hash pointer value immediately.
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Currently we must wait for enough entropy to become available before
hashed pointers can be printed. We can remove this wait by using the
hw RNG if available.
Use hw RNG to get keying material.
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Currently the function get_random_bytes_arch() has return value 'void'.
If the hw RNG fails we currently fall back to using get_random_bytes().
This defeats the purpose of requesting random material from the hw RNG
in the first place.
There are currently no intree users of get_random_bytes_arch().
Only get random bytes from the hw RNG, make function return the number
of bytes retrieved from the hw RNG.
Acked-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
There are a couple of whitespace issues around the function
get_random_bytes_arch(). In preparation for patching this function
let's clean them up.
Acked-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Fedora has integrated the jitter entropy daemon to work around slow
boot problems, especially on VM's that don't support virtio-rng:
https://bugzilla.redhat.com/show_bug.cgi?id=1572944
It's understandable why they did this, but the Jitter entropy daemon
works fundamentally on the principle: "the CPU microarchitecture is
**so** complicated and we can't figure it out, so it *must* be
random". Yes, it uses statistical tests to "prove" it is secure, but
AES_ENCRYPT(NSA_KEY, COUNTER++) will also pass statistical tests with
flying colors.
So if RDRAND is available, mix it into entropy submitted from
userspace. It can't hurt, and if you believe the NSA has backdoored
RDRAND, then they probably have enough details about the Intel
microarchitecture that they can reverse engineer how the Jitter
entropy daemon affects the microarchitecture, and attack its output
stream. And if RDRAND is in fact an honest DRNG, it will immeasurably
improve on what the Jitter entropy daemon might produce.
This also provides some protection against someone who is able to read
or set the entropy seed file.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Cc: Arnd Bergmann <arnd@arndb.de>
The removed code would be called in two situations:
1. interface is brought up never or >10s after driver load
2. after close()
Case 1 we can handle cleaner by ensuring chip is powered down when
leaving probe(). open() callback will power up the chip.
In case 2 we call rtl_pll_power_down() twice currently, from the
close() callback and 10s later when entering runtime-suspend.
This is avoided by this patch.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
HWMON support for SFP modules
This patchset adds HWMON support to SFP modules. The two patches add
some attributes for temperature and power sensors which are currently
missing from the hwmon core. The third patch adds a helper for
filtering out characters in hwmon names which are invalid. The last
patch then extends the core SFP code to export the sensors found in
SFP modules.
This code has been tested with two SFP modules:
module OEM SFP-7000-85 rev 11.0 sn M1512220075 dc 160221
module FINISAR CORP. FTLF8524E2GNL rev A sn PW40MNN dc 160725
The anonymous module uses external calibration, while the FINISAR uses
internal calibration. Thus both code paths have been tested.
Due to the cross subsystem nature of these patches, as discussed with
the RFC, it is hoped Guenter Roeck will ACK the patches, and then Dave
Miller will merge them all via net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SFP modules can contain a number of sensors. The EEPROM also contains
recommended alarm and critical values for each sensor, and indications
of if these have been exceeded. Export this information via
HWMON. Currently temperature, VCC, bias current, transmit power, and
possibly receiver power is supported.
The sensors in the modules can either return calibrate or uncalibrated
values. Uncalibrated values need to be manipulated, using coefficients
provided in the SFP EEPROM. Uncalibrated receive power values require
floating point maths in order to calibrate them. Performing this in
the kernel is hard. So if the SFP module indicates it uses
uncalibrated values, RX power is not made available.
With this hwmon device, it is possible to view the sensor values using
lm-sensors programs:
in0: +3.29 V (crit min = +2.90 V, min = +3.00 V)
(max = +3.60 V, crit max = +3.70 V)
temp1: +33.0°C (low = -5.0°C, high = +80.0°C)
(crit low = -10.0°C, crit = +85.0°C)
power1: 1000.00 nW (max = 794.00 uW, min = 50.00 uW) ALARM (LCRIT)
(lcrit = 40.00 uW, crit = 1000.00 uW)
curr1: +0.00 A (crit min = +0.00 A, min = +0.00 A) ALARM (LCRIT, MIN)
(max = +0.01 A, crit max = +0.01 A)
The scaling sensors performs on the bias current is not particularly
good. The raw values are more useful:
curr1:
curr1_input: 0.000
curr1_min: 0.002
curr1_max: 0.010
curr1_lcrit: 0.000
curr1_crit: 0.011
curr1_min_alarm: 1.000
curr1_max_alarm: 0.000
curr1_lcrit_alarm: 1.000
curr1_crit_alarm: 0.000
In order to keep the I2C overhead to a minimum, the constant values,
such as limits and calibration coefficients are read once at module
insertion time. Thus only reading *_input and *_alarm properties
requires i2c read operations.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
HWMON device names are not allowed to contain "-* \t\n". Add a helper
which will return true if passed an invalid character. It can be used
to massage a string into a hwmon compatible name by replacing invalid
characters with '_'.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some sensors support reporting minimal and lower critical power, as
well as alarms when these thresholds are reached. Add support for
these attributes to the hwmon core.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enum hwmon_temp_lcrit_alarm exists, but the BIT definition is
missing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
