We use tlbop to map virtual address in the first beginning, however it
may map too much if DRAM size is not that big. We have to invalidate the
mapping when the page table is created.
Signed-off-by: Greentime Hu <greentime@andestech.com>
This way we can build kernel with CONFIG_CPU_LITTLE_ENDIAN=y. Build allmodconfig
and allnoconfig are available too. It also fixes the endian mismatch issue
because AFLAGS and LDFLAGS is not passed correctly.
Signed-off-by: Vincent Ren-Wei Chen <vincentc@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
It broke the 'allmodconfig' build when CONFIG_TRACE_IRQFLAGS is enabled.
Signed-off-by: Nick Chun-Ming Hu <nickhu@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
It broke the 'allmodconfig' build.
We need to include <linux/types.h> to make sure the type is defined
before using it.
Signed-off-by: Greentime Hu <greentime@andestech.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
It broke the 'allmodconfig' build.
fs/xfs/xfs_buf.c: In function 'xfs_buf_bio_end_io':
fs/xfs/xfs_buf.c:1242:3: error: implicit declaration of function 'invalidate_kernel_vmap_range' [-Werror=implicit-function-declaration]
invalidate_kernel_vmap_range(bp->b_addr, xfs_buf_vmap_len(bp));
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
fs/xfs/xfs_buf.c: In function 'xfs_buf_ioapply_map':
fs/xfs/xfs_buf.c:1312:4: error: implicit declaration of function 'flush_kernel_vmap_range' [-Werror=implicit-function-declaration]
flush_kernel_vmap_range(bp->b_addr,
^~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Greentime Hu <greentime@andestech.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
It broke the 'allmodconfig' build.
drivers/gpu/drm/udl/udl_fb.c: In function 'udl_fb_mmap':
drivers/gpu/drm/udl/udl_fb.c:183:52: error: 'PAGE_SHARED' undeclared (first use in this function)
if (remap_pfn_range(vma, start, page, PAGE_SIZE, PAGE_SHARED))
^~~~~~~~~~~
drivers/gpu/drm/udl/udl_fb.c:183:52: note: each undeclared identifier is reported only once for each function it appears in
make[4]: *** [drivers/gpu/drm/udl/udl_fb.o] Error 1
Signed-off-by: Greentime Hu <greentime@andestech.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
When I compiled with allmodconfig, it caused this building failed.
crypto/xor.c:25:21: fatal error: asm/xor.h: No such file or directory
#include <asm/xor.h>
^
compilation terminated.
Signed-off-by: Greentime Hu <greentime@andestech.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
To include kernel/Kconfig.freezer to make sure the dependency between
CONFIG_CGROUP_FREEZER and CONFIG_FREEZER
It will cause building error when I make allmodconfig.
kernel/cgroup/freezer.c: In function 'freezer_css_online':
kernel/cgroup/freezer.c:116:15: error: 'system_freezing_cnt' undeclared (first use in this function)
atomic_inc(&system_freezing_cnt);
^~~~~~~~~~~~~~~~~~~
kernel/cgroup/freezer.c:116:15: note: each undeclared identifier is reported only once for each function it appears in
kernel/cgroup/freezer.c: In function 'freezer_css_offline':
kernel/cgroup/freezer.c:137:15: error: 'system_freezing_cnt' undeclared (first use in this function)
atomic_dec(&system_freezing_cnt);
^~~~~~~~~~~~~~~~~~~
kernel/cgroup/freezer.c: In function 'freezer_attach':
kernel/cgroup/freezer.c:181:4: error: implicit declaration of function 'freeze_task' [-Werror=implicit-function-declaration]
freeze_task(task);
^~~~~~~~~~~
kernel/cgroup/freezer.c: In function 'freezer_apply_state':
kernel/cgroup/freezer.c:360:16: error: 'system_freezing_cnt' undeclared (first use in this function)
atomic_inc(&system_freezing_cnt);
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Greentime Hu <greentime@andestech.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
We can use the generic lib to fix these error because the symbol of
libgcc in toolchain is not exported.
ERROR: "__ucmpdi2" [fs/xfs/xfs.ko] undefined!
ERROR: "__ashrdi3" [fs/xfs/xfs.ko] undefined!
ERROR: "__lshrdi3" [fs/xfs/xfs.ko] undefined!
ERROR: "__ashldi3" [fs/ntfs/ntfs.ko] undefined!
...
Signed-off-by: Greentime Hu <greentime@andestech.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add the UFS QMP phy node and the UFS host controller node, now that we
have working UFS and the necessary clocks in place.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Remove the usage of IRQ_TYPE_NONE to fix loud warnings from
patch (83a86fbb5b "irqchip/gic: Loudly complain about
the use of IRQ_TYPE_NONE").
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This is pure-churn and should be a no-op. I'm doing it in the hopes
of reducing merge conflicts. When things are sorted in a sane way
(and by base address seems sane) then it's less likely that future
patches will cause merge conflicts.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Let's keep the reserved-memory node tidy and neat and keep it sorted
by address. This should have no functional change.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add command DB node based on the bindings example.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The RPMh clock driver assumes that the xo_board clock is named
"xo_board", not "xo-board". Add a "clock-output-names" property to
the device tree to get the right name.
Also add the proper speed for the xo-clock as 38400000. This is
internally divided in RPMh clock driver to get "bi_tcxo" at 19200000.
After this change the clock tree in /sys/kernel/debug/clk/clk_summary
looks much better.
NOTES:
- Technically you could argue that this clock could belong in board
.dts files, not in the SoC one. However at the moment it's believed
that 100% of sdm845 boards will have an external clock at 38.4. It
can always be moved later if necessary.
- We could rename the "xo-board" device tree node to "xo_board" to
achieve the same effect as this patch. Presumably device-tree folks
would rather keep node names using dashes though.
- We could change the RPMh clock driver to use a dash to achieve the
same effect as this patch, but all other clocks in the clock tree
use underscores. It seems silly to change just this one.
Fixes: 7bafa643647f ("arm64: dts: sdm845: Add minimal dts/dtsi files for sdm845 SoC and MTP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add all the necessary dt nodes to support SMEM driver
on SDM845. It also adds the required memory carveouts
so that the kernel does not access memory that is in
use.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch add the node to support APSS shared
mailbox on SDM845
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Remove the usage of IRQ_TYPE_NONE to fix loud warnings from
patch (83a86fbb5b "irqchip/gic: Loudly complain about
the use of IRQ_TYPE_NONE").
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Thierry Escande <thierry.escande@linaro.org>
Tested-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Command DB provides information on shared resources like clocks,
regulators etc., probed at boot by the remote subsytem and made
available in shared memory.
Cc: devicetree@vger.kernel.org
Signed-off-by: Mahesh Sivasubramanian <msivasub@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds missing microSD card supplies, without this uSD
card will not be detected.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add device tree binding support for the QCOM GENI SE driver.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add binding document for serial bluetooth chips using Qualcomm protocol.
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add a new serial node for the Qualcomm BT controller QCA6174. This
allows automatic probing and hci registration through the serdev
framework instead of relying on the userspace helpers.
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables regulators and gpios for the Qualcomm QCA6174 BT/WLAN
combo controller.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The node name for a PCIe host bridge must be "pcie" as required by
the binging. dtc now warns about it:
arch/arm64/boot/dts/qcom/apq8096-db820c.dtb: Warning (pci_bridge): /soc/agnoc@0/qcom,pcie@610000: node name is not "pci" or "pcie"
arch/arm64/boot/dts/qcom/apq8096-db820c.dtb: Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'
arch/arm64/boot/dts/qcom/msm8996-mtp.dtb: Warning (pci_bridge): /soc/agnoc@0/qcom,pcie@610000: node name is not "pci" or "pcie"
arch/arm64/boot/dts/qcom/msm8996-mtp.dtb: Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'
This renames the nodes as appropriate.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
With the addition of this ramoops node it enables post mortem
analysis if a debug cable is not attached and/or not available.
All addresses and values were extracted from CAF AOSP marshmallow
DR 1.6.
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This enables SDHCI on the Nexus 5X as well creates common smd_rpm node
which can be shared between both 5X and 6P as per HW design.
Given the lack of documentation, only downstream code was used as a reference
and it eludes to the fact that 8994-rpm-regulator is common between both msm8992
& msm8994. [ see msm.git branch: msm-angler-3.10-marshmallow-mr1, msm8992.dtsi]
At this early stage of development it makes sense for the 8994-rpm-regulator
to be common until data / documentation suggests otherwise.
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Sudarsana Reddy Kalluru says:
====================
qed*: Add support for management firmware TLV request.
Management firmware (MFW) requires config and state information from
the driver. It queries this via TLV (type-length-value) request wherein
mfw specificies the list of required TLVs. Driver fills the TLV data
and responds back to MFW.
This patch series adds qed/qede/qedf/qedi driver implementation for
supporting the TLV queries from MFW.
Changes from previous versions:
-------------------------------
v2: Split patch (2) into multiple simpler patches.
v2: Update qed_tlv_parsed_buf->p_val datatype to void pointer to avoid
bunch of unnecessary typecasts.
Please consider applying this series to "net-next".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds callbacks for providing the ethernet protocol driver TLVs.
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds callbacks for providing the ethernet protocol driver TLVs.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds callbacks for providing the ethernet protocol driver TLVs.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MFW requests the TLVs in interrupt context. Extracting of the required
data from upper layers and populating of the TLVs require process context.
The patch adds work-queues for processing the tlv requests. It also adds
the implementation for requesting the tlv values from appropriate protocol
driver.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for processing TLV requests/repsonses
from the mfw and upper driver layers respectively. The implementation
reads the requested TLVs from the shared memory, requests the values
from upper layer drivers, populates this info (TLVs) shared memory and
notifies MFW about the TLV values.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds required management firmware (MFW) interfaces such as
mailbox commands, TLV types etc.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
memory-barriers.txt has been updated with the following requirement.
"When using writel(), a prior wmb() is not needed to guarantee that the
cache coherent memory writes have completed before writing to the MMIO
region."
Current writeX() and iowriteX() implementations on alpha are not
satisfying this requirement as the barrier is after the register write.
Move mb() in writeX() and iowriteX() functions to guarantee that HW
observes memory changes before performing register operations.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Matt Turner <mattst88@gmail.com>
The generic dma_direct implementation does the same thing as the alpha
pci-noop implementation, just with more bells and whistles. And unlike
the current code it at least has a theoretical chance to actually compile.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Older models of Chromebooks did not describe the LPC EC in their ACPI
tables; starting with Strago-based devices Google is using GOOG0004 device
to describe EC LPC.
DMI-based match is fragile and does not work reliably, especially when
using custom firmware. It is also not needed when we can locate the right
ACPI device, so let's stop bailing out when DMI does not match but the
right ACPI device is present.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
The x86/mtrr code does horrific things because hardware. It uses
stop_machine_from_inactive_cpu(), which does a wakeup (of the stopper
thread on another CPU), which uses RCU, all before the CPU is onlined.
RCU complains about this, because wakeups use RCU and RCU does
(rightfully) not consider offline CPUs for grace-periods.
Fix this by initializing RCU way early in the MTRR case.
Tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: Add !SMP support, per 0day Test Robot report. ]
If ext4_find_inline_data_nolock() returns an error it needs to get
reflected up to ext4_iget(). In order to fix this,
ext4_iget_extra_inode() needs to return an error (and not return
void).
This is related to "ext4: do not allow external inodes for inline
data" (which fixes CVE-2018-11412) in that in the errors=continue
case, it would be useful to for userspace to receive an error
indicating that file system is corrupted.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Cc: stable@kernel.org
The inline data feature was implemented before we added support for
external inodes for xattrs. It makes no sense to support that
combination, but the problem is that there are a number of extended
attribute checks that are skipped if e_value_inum is non-zero.
Unfortunately, the inline data code is completely e_value_inum
unaware, and attempts to interpret the xattr fields as if it were an
inline xattr --- at which point, Hilarty Ensues.
This addresses CVE-2018-11412.
https://bugzilla.kernel.org/show_bug.cgi?id=199803
Reported-by: Jann Horn <jannh@google.com>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Fixes: e50e5129f3 ("ext4: xattr-in-inode support")
Cc: stable@kernel.org
In case of error, the function dev_get_regmap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: e081c49e30 ("leds: Add Spreadtrum SC27xx breathing light controller driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
In unicast_arp_send function there is an inconsistency in error handling
of path_rec_start call. If path_rec_start is called because of an absent
ah field, skb will be dropped. But if it is called on a creation of a
new path, or if the path is invalid, skb will be added to the tail of
path queue. In case of a new path it will be dropped on path_free, but
in case of invalid path it can stay in the queue forever.
This patch unifies the behavior, dropping skb in all cases
of path_rec_start failure.
Signed-off-by: Evgenii Smirnov <evgenii.smirnov@profitbricks.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
