When resetting, phy_state_machine may be accessing the phy through
firmware if the phy is not stopped or disconnected, which will
cause firemware timeout problem because the firmware is busy
processing the reset request.
This patch fixes it by disabling the phy when resetting.
Fixes: b940aeae0ed6 ("net: hns3: never send command queue message to IMP when reset")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hardware sends the HCLGE_VECTOR0_EVENT_RST event through
hclge_misc_irq_handle, currently driver enables misc_vector in
the interrupt handle, and hardware generates the same interrupt
for the same reset event again and again until the reset is
complete, which causes hclge_reset running repeatly problem.
This patch fixes by enabling the misc_vector after reset is
complete.
Fixes: 4ed340ab8f ("net: hns3: Add reset process in hclge_main")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hclge_ae_stop is called during resetting, it will cancel the
service_task by calling cancel_work_sync, which may cause the
service_task to exit without clearing HCLGE_STATE_SERVICE_SCHED
bit. If this happens, the service_task will never run again.
This patch fixes this problem by clearing it after calling
cancel_work_sync in hclge_ae_stop.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing function reset or insmod hns3 dirver after rmmod,
the entries of mac vlan table are not cleared, which may cause
init mac address failed. This patch fixes it by clearing the
old mac address when doing function reset or rmmod hns3 driver.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checking for new mac address. It doesn't need to config
the mac vlan table if it's already in use.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for IFF_ALLMULTI flag to HNS3 PF and VF
driver.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is only 128 entries for hardware's vf vlan table, when
the vf table is full, the firmware will disable the vf vlan
filter and return a resp_code of HCLGE_VF_VLAN_NO_ENTRY to
driver.
This patch checks the if resp_code from firmware is
HCLGE_VF_VLAN_NO_ENTRY, if yes, then print a warning and
return ok to the caller.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The log entry dentries are only set, never referenced, so no need to
keep them around. Remove the pointer from struct
vchiq_debugfs_log_entry as it is not needed anymore and get rid of the
separate vchiq_debugfs_create_log_entries() function as it is only used
in one place.
Suggested-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to set this to be int * when it is only used as a void *.
This lets us remove the unneeded cast, and unneeded temporary variable
the one place it is referenced in the code.
Suggested-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure, and the one static variable that was declared with it,
were not being used for anything. The log_categories field was being
set, but never used again. So just remove it entirely as it is not
needed at all.
Suggested-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This does not need to be part of a wrapper function, or in a structure,
just properly reference it directly as a single variable.
The whole variable will be going away soon anyway, this is just a step
toward that direction.
Suggested-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vchiq_debugfs_top() is only a wrapper around a pointer to a dentry, so
just use the dentry directly instead, making it a static variable
instead of part of a static structure.
This also removes the pointless BUG_ON() when checking that dentry as no
one should ever care if debugfs is working or not, and the kernel should
really not panic over something as trivial as that.
Suggested-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Clean up the vchiq_arm code by not caring about the value of debugfs
calls. This ends up removing a number of lines of code that are not
needed.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Keerthi Reddy <keerthigd4990@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no bus infrastructure today to handle all the mmagic bus
clocks and GDSCs needed by all the multimedia blocks in msm8996, like
mdss, video, camera and gpu. Mark all these clocks with a CLK_IS_CRITICAL
and GDSCs with a ALWAYS_ON flag for now so they are left always enabled.
This patch should be reverted at some point when we do have a bus driver
to manage these clocks and GDSCs.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We have atleast some instances of ALWAYS_ON gdscs, which need to
be turned ON *before* some clocks within the gdsc domain marked
with a CLK_IS_CRITICAL can be turned ON.
To facilitate this sequence, register the GDCSs (and hence handle
the ALWAYS_ON gdscs) before we register clocks (and handle the
clocks marked as CLK_IS_CRITICAL)
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some GDSCs might have software control to turn them off, but we might
want to keep them enabled always, in some cases because of lack of
support in kernel to handle a graceful turning off/on of such GDSCs.
Most common instances would be the GDCSs which power up the noc/bus
fabrics, which need bus drivers to handle them and atleast support for
which is missing on all qcom SoCs.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Petr Machata says:
====================
Test mirror-to-gretap with bridge in UL
This patchset adds more tests to the mirror-to-gretap suite where bridge
is present in the underlay. Specifically it adds tests for bridge VLAN
handling, FDB, and bridge port STP status.
In patches #1-#3, the codebase is refactored to support the new tests.
In patch #4, an STP test is added to the mirroring library, that will
later be called from bridge tests.
In patches #5-#8, the test for mirror-to-gretap with an 802.1q bridge in
underlay is adapted and more tests are added.
In patch #9, an STP test is added to the test suite for mirror-to-gretap
with an 802.1d bridge in underlay.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To test offloading of mirror-to-gretap in mlxsw for cases that a
VLAN-unaware bridge is in underlay packet path, test that the STP status
of bridge egress port is reflected.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offloading of mirror-to-gretap in mlxsw is tricky especially in cases
when the gretap underlay involves bridges. Add more tests that exercise
the bridge handling code:
- forbidden_egress tests that check vlan removal on bridge port in the
underlay packet path
- untagged_egress tests that similarly check "egress untagged"
- fdb_roaming tests that check whether learning FDB on a different port
is reflected
- stp tests for handling port STP status of bridge egress port
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename test_gretap_forbidden() and test_ip6gretap_forbidden() to a more
specific test_gretap_forbidden_cpu() and test_ip6gretap_forbidden_cpu().
This will make it clearer which is which when further down a patch is
introduced that forbids a VLAN on regular bridge port.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the final change reestablishes the original configuration, make
sure the traffic flows again as it should.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "ip6gretap" in the test name refers to the tunnel device type that
the test is supposed to be testing. However test_ip6gretap_forbidden()
tests, due to a typo, a gretap tunnel. Fix the typo.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a reusable full test that toggles STP state of a given bridge port
and checks that the mirroring reacts appropriately. The test will be
used by bridge tests in follow-up patches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VLAN capture is installed on a front panel device and not a
soft device, the packets are counted twice: once in fast path, and once
after they are trapped to the kernel. Resolve the problem by passing
skip_hw flag to vlan_capture_install().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the function do_test_span_vlan_dir_ips() from mirror_vlan.sh test
to a library file mirror_lib.sh to allow reuse. Fill in other entry
points similar to other testing functions in mirror_lib.sh, they will be
useful in following patches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move vlan_capture_install() and vlan_capture_uninstall() from
mirror_vlan.sh test to lib.sh so that it can be reused in other tests.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing Telit LM940 with ICMP packets > 14552 bytes revealed that
the modem needs FLAG_SEND_ZLP to properly work, otherwise the cdc
mbim data interface won't be anymore responsive.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the appropriate SPDX license identifier and drop the previous
license text.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Nicolas Dichtel says:
====================
ip[6] tunnels: fix mtu calculations
The first patch restores the possibility to bind an ip4 tunnel to an
interface whith a large mtu.
The second patch was spotted after the first fix. I also target it to net
because it fixes the max mtu value that can be used for ipv6 tunnels.
v2: remove the 0xfff8 in ip_tunnel_newlink()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up: This array was used in a dprintk that was replaced by a
trace point in commit ab03eff58e ("xprtrdma: Add trace points in
RPC Call transmit paths").
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Currently, when the sendctx queue is exhausted during marshaling, the
RPC/RDMA transport places the RPC task on the delayq, which forces a
wait for HZ >> 2 before the marshal and send is retried.
With this change, the transport now places such an RPC task on the
pending queue, and wakes it just as soon as more sendctxs become
available. This typically takes less than a millisecond, and the
write_space waking mechanism is less deadlock-prone.
Moreover, the waiting RPC task is holding the transport's write
lock, which blocks the transport from sending RPCs. Therefore faster
recovery from sendctx queue exhaustion is desirable.
Cf. commit 5804891455d5 ("xprtrdma: ->send_request returns -EAGAIN
when there are no free MRs").
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: The logic to wait for write space is common to a bunch of
the encoding helper functions. Lift it out and put it in the tail
of rpcrdma_marshal_req().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The use of -EAGAIN in rpcrdma_convert_iovs() is a latent bug: the
transport never calls xprt_write_space() when more pages become
available. -ENOBUFS will trigger the correct "delay briefly and call
again" logic.
Fixes: 7a89f9c626 ("xprtrdma: Honor ->send_request API contract")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: stable@vger.kernel.org # 4.8+
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
After commit f6cc9c054e, the following conf is broken (note that the
default loopback mtu is 65536, ie IP_MAX_MTU + 1):
$ ip tunnel add gre1 mode gre local 10.125.0.1 remote 10.125.0.2 dev lo
add tunnel "gre0" failed: Invalid argument
$ ip l a type dummy
$ ip l s dummy1 up
$ ip l s dummy1 mtu 65535
$ ip tunnel add gre1 mode gre local 10.125.0.1 remote 10.125.0.2 dev dummy1
add tunnel "gre0" failed: Invalid argument
dev_set_mtu() doesn't allow to set a mtu which is too large.
First, let's cap the mtu returned by ip_tunnel_bind_dev(). Second, remove
the magic value 0xFFF8 and use IP_MAX_MTU instead.
0xFFF8 seems to be there for ages, I don't know why this value was used.
With a recent kernel, it's also possible to set a mtu > IP_MAX_MTU:
$ ip l s dummy1 mtu 66000
After that patch, it's also possible to bind an ip tunnel on that kind of
interface.
CC: Petr Machata <petrm@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
Link: https://git.kernel.org/pub/scm/linux/kernel/git/davem/netdev-vger-cvs.git/commit/?id=e5afd356a411a
Fixes: f6cc9c054e ("ip_tunnel: Emit events for post-register MTU changes")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
and removal of the initial devicetree-based gate-clocks, which were
deprecated since 2014.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlsGtG0QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgUE2B/9IoOlNNuueUyyinAcY0XyIzDcnXfqwAbYL
+oVlUCyVoIne/Xu7kqk7P9lMoh6YAlzOuDzsIIxmC3Dm/fhrc2Imqj4mwXWGxa9Y
hSndozhX642pRtvGbYthDXEY3OUfv11Ys6sq/maku8ssUvX81Lx288Q2sRwkjKQP
pr2Qjxo0oqbaKo7nGsPAN7sgTmS+1yO4zoyc0cDLYMIZw6KT23R/LpCA/uuJhMv3
gbe2t8XCFP2/qjhNGcb+rs6znRRDbNwYPcoAImTBAKwUH2KD2LBWFpOBhDnSX5ZX
jIHLrpWYK0HhxriqL0oPaME1paRV0FHBw1WHeJ79YPf5wkfdPwGl
=VzkZ
-----END PGP SIGNATURE-----
Merge tag 'v4.18-rockchip-clk-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-rockchip
Pull rockchip clk driver updates from Heiko Stuebner:
Conversion to match_string helper of open-coded string comparison
and removal of the initial devicetree-based gate-clocks, which were
deprecated since 2014.
* tag 'v4.18-rockchip-clk-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: remove deprecated gate-clk code and dt-binding
clk: rockchip: use match_string() helper
Steffen Klassert says:
====================
pull request (net): ipsec 2018-05-31
1) Avoid possible overflow of the offset variable
in _decode_session6(), this fixes an infinite
lookp there. From Eric Dumazet.
2) We may use an error pointer in the error path of
xfrm_bundle_create(). Fix this by returning this
pointer directly to the caller.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Not a lot of changes for this release, but two quite important features
were added: the H6 PRCM clock support, and the needed changes to the R40
clock driver to allow for the EMAC to operate.
-----BEGIN PGP SIGNATURE-----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=Tv3O
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-allwinner
Pull Allwinner clock changes from Maxime Ripard:
Not a lot of changes for this release, but two quite important features
were added: the H6 PRCM clock support, and the needed changes to the R40
clock driver to allow for the EMAC to operate.
* tag 'sunxi-clk-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: r40: export a regmap to access the GMAC register
clk: sunxi-ng: r40: rewrite init code to a platform driver
clk: sunxi-ng: add support for H6 PRCM CCU
We can document other "Known Limitations" but the ones currently
referenced don't hold anymore...
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix outdated statement that KVM is not able to expose SLAT
(Second-Layer-Address-Translation) to guests.
This was implemented a long time ago...
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
This cleans up the error handling a lot, as this code will never get
hit.
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Christoffer Dall <christoffer.dall@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim KrÄmář" <rkrcmar@redhat.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Eric Auger <eric.auger@redhat.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: kvm-ppc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: kvmarm@lists.cs.columbia.edu
Cc: kvm@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The kvm struct has been bloating. For example, it's tens of kilo-bytes
for x86, which turns out to be a large amount of memory to allocate
contiguously via kzalloc. Thus, this patch does the following:
1. Uses architecture-specific routines to allocate the kvm struct via
vzalloc for x86.
2. Switches arm to __KVM_HAVE_ARCH_VM_ALLOC so that it can use vzalloc
when has_vhe() is true.
Other architectures continue to default to kalloc, as they have a
dependency on kalloc or have a small-enough struct kvm.
Signed-off-by: Marc Orr <marcorr@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use new return type vm_fault_t for fault handler. For
now, this is just documenting that the function returns
a VM_FAULT value rather than an errno. Once all instances
are converted, vm_fault_t will become a distinct type.
commit 1c8f422059 ("mm: change return type to vm_fault_t")
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* Add critical flag to meson8b's fdiv2 as temporary fixup for the ethernet.
* Clean up license headers with SPDX
* Add round closest support to mpll driver.
-----BEGIN PGP SIGNATURE-----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=1m3M
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-4.18-2' of https://github.com/BayLibre/clk-meson into clk-meson
Pull Second round of update for meson clocks from Jerome Brunet:
- Add critical flag to meson8b's fdiv2 as temporary fixup for the ethernet.
- Clean up license headers with SPDX
- Add round closest support to mpll driver.
* tag 'meson-clk-4.18-2' of https://github.com/BayLibre/clk-meson:
clk: meson: axg: let mpll clocks round closest
clk: meson: mpll: add round closest support
clk: meson: meson8b: mark fclk_div2 gate clocks as CLK_IS_CRITICAL
clk: meson: use SPDX license identifiers consistently
- Lazy context-switching of FPSIMD registers on arm64
- Allow virtual redistributors to be part of two or more MMIO ranges
-----BEGIN PGP SIGNATURE-----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=DUmC
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for 4.18
- Lazy context-switching of FPSIMD registers on arm64
- Allow virtual redistributors to be part of two or more MMIO ranges
skl-tplg-interface.h describes firmware format details for Skylake
topology files. It is part of the ABI and should reside in the uapi
directory.
While moving the file, also replace the license boilerplate with
the SPDX License Identifier.
No functional change.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology manifest v4 is still part of the ABI. Move its data structures
into the uapi header file.
No functional change.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
