The microcontrollers are part of GT so it makes logical sense to have
them sanitized at the same time. This also fixed an issue with our
status tracking where the FW load status is not reset around
hibernation.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190723091404.6449-2-chris@chris-wilson.co.uk
This was the last place in gt/uc that was still using I915_READ
with the global dev_priv.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190723091404.6449-1-chris@chris-wilson.co.uk
Draining makes little sense in the situation of hardware overrun, as the
hardware will have consumed all its available samples. Additionally,
draining whilst the stream is paused would presumably get stuck as no
data is being consumed on the DSP side.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Partial drain and next track are intended for gapless playback and
don't really have an obvious interpretation for a capture stream, so
makes sense to not allow those operations on capture streams.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, whilst in SNDRV_PCM_STATE_OPEN it is possible to call
snd_compr_stop, snd_compr_drain and snd_compr_partial_drain, which
allow a transition to SNDRV_PCM_STATE_SETUP. The stream should
only be able to move to the setup state once it has received a
SNDRV_COMPRESS_SET_PARAMS ioctl. Fix this issue by not allowing
those ioctls whilst in the open state.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A previous fix to the stop handling on compressed capture streams causes
some knock on issues. The previous fix updated snd_compr_drain_notify to
set the state back to PREPARED for capture streams. This causes some
issues however as the handling for snd_compr_poll differs between the
two states and some user-space applications were relying on the poll
failing after the stream had been stopped.
To correct this regression whilst still fixing the original problem the
patch was addressing, update the capture handling to skip the PREPARED
state rather than skipping the SETUP state as it has done until now.
Fixes: 4f2ab5e1d1 ("ALSA: compress: Fix stop handling on compressed capture streams")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To identify the HDCP capability of the display connected to CI
systems, we need to add the hdcp capability probing in i915_display_info.
This will also help to populate the HDCP capability of the CI systems
to CI H/W logs maintained at https://intel-gfx-ci.01.org/hardware/.
It will facilitate to determine the kms_content_protection behavior on
a particular CI system.
v2: Reused the intel_hdcp_info() in i915_hdcp_sink_capability_show(). [Ram]
Shifted intel_hdcp_info() to the end of intel_dp_info. [Ram]
v3: used seq_puts() instead of seq_pritnf(). [Ram]
Cc: daniel.vetter@intel.com
Cc: ramalingam.c@intel.com
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190719055513.2089-1-anshuman.gupta@intel.com
Even though the binding mentions that the PHY name must be "phy", it turns
out that all our DTs had "hdmi-phy" instead.
The code doesn't care about the phy-names property, so we can just change
our DTs to match the binding, without any side effect.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
simple-panel based bindings need only the display compatible, and
simple-panel isn't documented anywhere. Remove it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add KASAN instrumentation of architecture-specific asm implementation
of bitops. It also covers s390 specific *_inv functions.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Make s390/bitops test functions return bool values. That enforces return
value range to 0 and 1 and matches with asm-generic/bitops-instrumented.h
declarations as well as some other architectures implementations.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Tested (64-bit and compat mode) using program from
http://lkml.kernel.org/r/20190604212930.jaaztvkent32b7d3@brauner.io
with the following:
return syscall(__NR_clone, flags, 0, pidfd, 0, 0);
changed to:
return syscall(__NR_clone, 0, flags, pidfd, 0, 0);
due to CLONE_BACKWARDS2.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Masahiro Yamada changed the zcrypt.h header file to use __u{16,32,64}
instead of uint{16,32,64}_t with ("s390: use __u{16,32,64} instead of
uint{16,32,64}_t in uapi header").
This makes all s390 header files pass - remove zcrypt.h from the blacklist.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
When CONFIG_UAPI_HEADER_TEST=y, exported headers are compile-tested to
make sure they can be included from user-space.
Currently, zcrypt.h is excluded from the test coverage. To make it
join the compile-test, we need to fix the build errors attached below.
For a case like this, we decided to use __u{8,16,32,64} variable types
in this discussion:
https://lkml.org/lkml/2019/6/5/18
Build log:
CC usr/include/asm/zcrypt.h.s
In file included from <command-line>:32:0:
./usr/include/asm/zcrypt.h:163:2: error: unknown type name ‘uint16_t’
uint16_t cprb_len;
^~~~~~~~
./usr/include/asm/zcrypt.h:168:2: error: unknown type name ‘uint32_t’
uint32_t source_id;
^~~~~~~~
./usr/include/asm/zcrypt.h:169:2: error: unknown type name ‘uint32_t’
uint32_t target_id;
^~~~~~~~
./usr/include/asm/zcrypt.h:170:2: error: unknown type name ‘uint32_t’
uint32_t ret_code;
^~~~~~~~
./usr/include/asm/zcrypt.h:171:2: error: unknown type name ‘uint32_t’
uint32_t reserved1;
^~~~~~~~
./usr/include/asm/zcrypt.h:172:2: error: unknown type name ‘uint32_t’
uint32_t reserved2;
^~~~~~~~
./usr/include/asm/zcrypt.h:173:2: error: unknown type name ‘uint32_t’
uint32_t payload_len;
^~~~~~~~
./usr/include/asm/zcrypt.h:182:2: error: unknown type name ‘uint16_t’
uint16_t ap_id;
^~~~~~~~
./usr/include/asm/zcrypt.h:183:2: error: unknown type name ‘uint16_t’
uint16_t dom_id;
^~~~~~~~
./usr/include/asm/zcrypt.h:198:2: error: unknown type name ‘uint16_t’
uint16_t targets_num;
^~~~~~~~
./usr/include/asm/zcrypt.h:199:2: error: unknown type name ‘uint64_t’
uint64_t targets;
^~~~~~~~
./usr/include/asm/zcrypt.h:200:2: error: unknown type name ‘uint64_t’
uint64_t weight;
^~~~~~~~
./usr/include/asm/zcrypt.h:201:2: error: unknown type name ‘uint64_t’
uint64_t req_no;
^~~~~~~~
./usr/include/asm/zcrypt.h:202:2: error: unknown type name ‘uint64_t’
uint64_t req_len;
^~~~~~~~
./usr/include/asm/zcrypt.h:203:2: error: unknown type name ‘uint64_t’
uint64_t req;
^~~~~~~~
./usr/include/asm/zcrypt.h:204:2: error: unknown type name ‘uint64_t’
uint64_t resp_len;
^~~~~~~~
./usr/include/asm/zcrypt.h:205:2: error: unknown type name ‘uint64_t’
uint64_t resp;
^~~~~~~~
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
get_maintainer.pl only returns linux-kernel@vger.kernel.org for the
drivers/soc/ux500/ files - fix it by adding drivers/soc/ux500/ entry
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The debug UART code defined three different virtual addresses
while only one is ever used. Get rid of this, and move the
UART remapping to 0xfffe8000 where DTCM reside on some platforms
but not on Ux500, so it can be reused moving the UART out of the
vmalloc area.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IQD mcast queue doesn't support QAOB mode, so skip the
qdio_enable_async_operation() setup call for this queue. This avoids
the allocation of an unneeded QAOB pointer array, and sets up q->use_cq
properly so that drivers are prohibited from using QAOBs for mcast
traffic.
Take this opportunity to streamline the q->use_cq and aob != 0 checks.
The path to qdio_siga_output() is straight-forward, we don't need to
worry about being called with bad operands.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
If the device driver were to send out a full queue's worth of SBALs,
current code would end up discovering the last of those SBALs as PRIMED
and erroneously skip the SIGA-w. This immediately stalls the queue.
Add a check to not attempt fast-requeue in this case. While at it also
make sure that the state of the previous SBAL was successfully extracted
before inspecting it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Extend "parmarea" to include an offset of the version string, which is
stored as 8-byte big endian value.
To retrieve version string from bzImage reliably, one should check the
presence of "S390EP" ascii string at 0x10008 (available since v3.2),
then read the version string offset from 0x10428 (which has been 0
since v3.2 up to now). The string is null terminated.
Could be retrieved with the following "file" command magic (requires
file v5.34):
8 string \x02\x00\x00\x18\x60\x00\x00\x50\x02\x00\x00\x68\x60\x00\x00\x50\x40\x40\x40\x40\x40\x40\x40\x40 Linux S390
>0x10008 string S390EP
>>0x10428 bequad >0
>>>(0x10428.Q) string >\0 \b, version %s
Reported-by: Petr Tesarik <ptesarik@suse.com>
Suggested-by: Petr Tesarik <ptesarik@suse.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Add an entry for TechNexion PICO-PI-IMX8M board based on i.MX8MQ SoC
Datasheet can be found at:
https://s3.us-east-2.amazonaws.com/technexion/datasheets/picopiimx8m.pdf
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Andra Danciu <andradanciu1997@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We use "pmc->idx" and the "chained" bitmap to determine if the pmc is
chained, in kvm_pmu_pmc_is_chained(). But idx might be uninitialized
(and random) when we doing this decision, through a KVM_ARM_VCPU_INIT
ioctl -> kvm_pmu_vcpu_reset(). And the test_bit() against this random
idx will potentially hit a KASAN BUG [1].
In general, idx is the static property of a PMU counter that is not
expected to be modified across resets, as suggested by Julien. It
looks more reasonable if we can setup the PMU counter idx for a vcpu
in its creation time. Introduce a new function - kvm_pmu_vcpu_init()
for this basic setup. Oh, and the KASAN BUG will get fixed this way.
[1] https://www.spinics.net/lists/kvm-arm/msg36700.html
Fixes: 80f393a23b ("KVM: arm/arm64: Support chained PMU counters")
Suggested-by: Andrew Murray <andrew.murray@arm.com>
Suggested-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
I mistakenly dropped the inline while resolving the patch conflicts in
the previous fix patch. Without inline, we get compiler warnings wrt
unused functions.
Note that Mauro's original patch contained the correct changes; it's
all my fault to submit a patch before a morning coffee.
Fixes: c8917b8ff0 ("firmware: fix build errors in paged buffer handling code")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20190723081159.22624-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stub function for !CONFIG_IOMMU_IOVA needs to be
'static inline'.
Fixes: effa467870 ('iommu/vt-d: Don't queue_iova() if there is no flush queue')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The DSP interrupt steer gathers interrupts from the system
and can be used to steer them to DSP.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LSIO subsystem contains 14 MU instances.
5 MUs to communicate between AP <-> SCU
- side-A PD range managed by AP
- side-B PD range managed by SCU
9 MUs to communicate between all cores (AP/M4/DSP).
- side-A PD range managed by core-A (AP/M4/DSP)
- side-B PD range managed by core-B (AP/M4/DSP).
Communication between AP <-> DSP is done through the
assigned MU number 13.
So, we power up side-A by the AP and we decide to
power up side-B also from AP. This is because powering
it up from DSP would be painful.
Powering up side B from DSP would require the DSP to
communicate with SCU and to keep things simple we don't
want that now.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
of_find_compatible_node() returns a pointer with refcount incremented
so both in the error path as well as after usage in soc_info_populate()
respectively actually b8500_read_soc_id() an explicit of_node_put is
needed to release backupram.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: commit 18a9927878 ("ARM: ux500: move soc_id driver to drivers/soc")
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Messaging Unit module enables two processors within the SoC to
communicate and coordinate by passing messages through the MU interface.
MUs have 2 “sides” with independent programming interfaces. Rename
mu PD range to mu_a because it's actually side A of MUs.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cpu variable is still being used in the of_get_property() call
after the of_node_put() call, which may result in use-after-free.
Fixes: a9acc26b75 ("cpufreq/pasemi: fix possible object reference leak")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
GIC is inside of SoC from architecture perspective, it should
be located inside of soc node in DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GIC is inside of SoC from architecture perspective, it should
be located inside of soc node in DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GIC is inside of SoC from architecture perspective, it should
be located inside of soc node in DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GIC is inside of SoC from architecture perspective, it should
be located inside of soc node in DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Note that after previous changes dpm_noirq_begin() and
dpm_noirq_end() each have only one caller, so move the code from
them to their respective callers and drop them.
Also note that dpm_noirq_resume_devices() and
dpm_noirq_suspend_devices() need not be exported any more, so make
them both static.
This change is not expected to alter functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
After previous changes the suspend-to-idle code flow can be
integrated more tightly with the generic system suspend code flow
by making suspend_enter() call s2idle_loop() later and removing
the direct invocations of dpm_noirq_begin(),
dpm_noirq_suspend_devices(), dpm_noirq_end(), and
dpm_noirq_resume_devices() from the latter, so do that.
This change is not expected to alter functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
After commit 33e4f80ee6 ("ACPI / PM: Ignore spurious SCI wakeups
from suspend-to-idle") the "noirq" phases of device suspend and
resume may run for multiple times during suspend-to-idle, if there
are spurious system wakeup events while suspended. However, this
is complicated and fragile and actually unnecessary.
The main reason for doing this is that on some systems the EC may
signal system wakeup events (power button events, for example) as
well as events that should not cause the system to resume (spurious
system wakeup events). Thus, in order to determine whether or not
a given event signaled by the EC while suspended is a proper system
wakeup one, the EC GPE needs to be dispatched and to start with that
was achieved by allowing the ACPI SCI action handler to run, which
was only possible after calling resume_device_irqs().
However, dispatching the EC GPE this way turned out to take too much
time in some cases and some EC events might be missed due to that, so
commit 68e2201185 ("ACPI: EC: Dispatch the EC GPE directly on
s2idle wake") started to dispatch the EC GPE right after a wakeup
event has been detected, so in fact the full ACPI SCI action handler
doesn't need to run any more to deal with the wakeups coming from the
EC.
Use this observation to simplify the suspend-to-idle control flow
so that the "noirq" phases of device suspend and resume are each
run only once in every suspend-to-idle cycle, which is reported to
significantly reduce power drawn by some systems when suspended to
idle (by allowing them to reach a deep platform-wide low-power state
through the suspend-to-idle flow). [What appears to happen is that
the "noirq" resume of devices after a spurious EC wakeup brings some
devices into a state in which they prevent the platform from reaching
the deep low-power state going forward, even after a subsequent
"noirq" suspend phase, and on some systems the EC triggers such
wakeups already when the "noirq" suspend of devices is running for
the first time in the given suspend/resume cycle, so the platform
cannot reach the deep low-power state at all.]
First, make acpi_s2idle_wake() use the acpi_ec_dispatch_gpe() return
value to determine whether or not the wakeup may have been triggered
by the EC (in which case the system wakeup is canceled and ACPI
events are processed in order to determine whether or not the event
is a proper system wakeup one) and use rearm_wake_irq() (introduced
by a previous change) in it to rearm the ACPI SCI for system wakeup
detection in case the system will remain suspended.
Second, drop acpi_s2idle_sync(), which is not needed any more, and
the corresponding global platform suspend-to-idle callback.
Next, drop the pm_wakeup_pending() check (which is an optimization
only) from __device_suspend_noirq() to prevent it from returning
errors on system wakeups occurring before the "noirq" phase of
device suspend is complete (as in the case of suspend-to-idle it is
not known whether or not these wakeups are suprious at that point),
in order to avoid having to carry out a "noirq" resume of devices
on a spurious system wakeup.
Finally, change the code flow in s2idle_loop() to (1) run the
"noirq" suspend of devices once before starting the loop, (2) check
for spurious EC wakeups (via the platform ->wake callback) for the
first time before calling s2idle_enter(), and (3) run the "noirq"
resume of devices once after leaving the loop.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
The role of the s2idle_wakeup variable is to cause
acpi_pm_wakeup_event() and acpi_pm_notify_handler() to
increment pm_abort_suspend and trigger a wakeup from
suspend-to-idle in case the ACPI SCI wakeup was canceled
by acpi_s2idle_wake().
However, for this purpose it need not be set in acpi_s2idle_wake()
and cleared in acpi_s2idle_sync(), respectively. In fact, it
may be set as early as in acpi_s2idle_prepare() and cleared as
late as in acpi_s2idle_restore(), so do that to allow subsequent
changes to be simpler.
This change is not expected to alter functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
It is not actually guaranteed that pm_abort_suspend will be
nonzero when pm_system_cancel_wakeup() is called which may lead to
subtle issues, so make it use atomic_dec_if_positive() instead of
atomic_dec() for the safety sake.
Fixes: 33e4f80ee6 ("ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
On some systems, if suspend-to-idle is used, the EC may signal system
wakeup events (power button events, for example) as well as events
that should not cause the system to resume and acpi_ec_dispatch_gpe()
needs to be called to determine whether or not the system should
resume then. In particular, if acpi_ec_dispatch_gpe() doesn't detect
any EC events at all, the system should remain suspended, so it is
useful to know when that is the case.
For this reason, make acpi_ec_dispatch_gpe() return a bool value
indicating whether or not any EC events have been detected by it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
In some cases it is useful to know whether or not the
acpi_ev_detect_gpe() called by acpi_dispatch_gpe() has found
the GPE to be active, so return the return value of it (whose
data type is u32) from latter.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Introduce a new function, rearm_wake_irq(), allowing a wakeup IRQ
to be armed for systen wakeup detection again without running any
action handlers associated with it after it has been armed for
wakeup detection and triggered.
That is useful for IRQs, like ACPI SCI, that may deliver wakeup
as well as non-wakeup interrupts when armed for systen wakeup
detection. In those cases, it may be possible to determine whether
or not the delivered interrupt is a systen wakeup one without
running the entire action handler (or handlers, if the IRQ is
shared) for the IRQ, and if the interrupt turns out to be a
non-wakeup one, the IRQ can be rearmed with the help of the
new function.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
The i.MX8M SAI block is not compatible with the i.MX6SX one, as the
register layout has changed due to two version registers being added
at the beginning of the address map. Remove the bogus compatible.
Fixes: 8c61538dc9 ("arm64: dts: imx8mq: Add SAI2 node")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Passing 0 to cpuhp_remove_state() triggers the BUG_ON() in
__cpuhp_remove_state_cpuslocked() and the argument passed to
powercap_unregister_control_type() is expected to be a valid
pointer, so avoid calling these functions with incorrect
arguments from proc_thermal_rapl_remove().
Fixes: 555c45fe0d ("int340X/processor_thermal_device: add support for MMIO RAPL")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
