Initially, the TMU_ROOT clock was marked as critical, which automatically
made the AHB clock to stay always on. Since the TMU_ROOT clock is not
marked as critical anymore, following commit:
"clk: imx8mq: Remove CLK_IS_CRITICAL flag for IMX8MQ_CLK_TMU_ROOT"
all the clocks that derive from ipg_root clock (and implicitly ahb clock)
would also have to enable, along with their own gate, the AHB clock.
But considering that AHB is actually a bus that has to be always on, we mark
it as critical in the clock provider driver and then all the clocks that
derive from it can be controlled through the dedicated per IP gate which
follows after the ipg_root clock.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use a space before and after assignment operator to have consistent
style.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DRM_WAIT_ON() is from the deprecated drm_os_linux header and
the modern replacement is the wait_event_*.
The return values differ, so a conversion is needed to
keep the original interface towards userspace.
Introduced a switch/case to make code obvious.
Analysis from Michel Dänzer:
The waiting condition rely on all relevant places where vblank_count
is modified calls wake_up(&vblank->queue).
drm_handle_vblank():
- Calls wake_up(&vblank->queue)
drm_vblank_enable():
- There is no need here because there can be no sleeping waiters
in the queue, because vblank->enabled == false immediately
terminates any waits.
drm_crtc_accurate_vblank_count():
- This is called from interrupt handlers, at least from
amdgpu_dm.c:dm_pflip_high_irq(). Not sure it needs to wake up
the queue though, the driver should call
drm_(crtc_)_handle_vblank anyway.
drm_vblank_disable_and_save():
- It can be called from an interrupt, via drm_handle_vblank ->
vblank_disable_fn. However, the only place where
drm_vblank_disable_and_save can be called with sleeping waiters
in the queue is in drm_crtc_vblank_off, which wakes up the queue
afterwards (which terminates all waits, because
vblank->enabled == false at this point).
v3:
- Added analysis to changelog from Michel Dänzer
- Moved return result handling inside if (req_seq != seq) (Daniel V)
- Reused more of the former logic - resulting in simpler code
- Dropped Reviewed-by from Sean Paul as this is a new implementation
v2:
- Fix so the case where req_seq equals seq was handled properly
- quick hack to check if IGT became happy
- Only sent to igt, not to dri-devel
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190726210658.GA6299@ravnborg.org
Let's document why the lock is not needed in acpi_scan_init(), right now
this is not really obvious.
[akpm@linux-foundation.org: fix tpyo]
Link: http://lkml.kernel.org/r/20190731135306.31524-1-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
memremap.c implements MM functionality for ZONE_DEVICE, so it really
should be in the mm/ directory, not the kernel/ one.
Link: http://lkml.kernel.org/r/20190722094143.18387-1-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kmalloc() shouldn't sleep while in RCU critical section, therefore use
GFP_ATOMIC instead of GFP_KERNEL.
The bug was spotted by the 0day kernel testing robot.
Link: http://lkml.kernel.org/r/20190725121703.210874-1-glider@google.com
Fixes: 7e659650cbda ("lib: introduce test_meminit module")
Signed-off-by: Alexander Potapenko <glider@google.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit d66acc39c7 ("bitops: Optimise get_order()") introduced a
compilation warning because "rx_frag_size" is an "ushort" while
PAGE_SHIFT here is 16.
The commit changed the get_order() to be a multi-line macro where
compilers insist to check all statements in the macro even when
__builtin_constant_p(rx_frag_size) will return false as "rx_frag_size"
is a module parameter.
In file included from ./arch/powerpc/include/asm/page_64.h:107,
from ./arch/powerpc/include/asm/page.h:242,
from ./arch/powerpc/include/asm/mmu.h:132,
from ./arch/powerpc/include/asm/lppaca.h:47,
from ./arch/powerpc/include/asm/paca.h:17,
from ./arch/powerpc/include/asm/current.h:13,
from ./include/linux/thread_info.h:21,
from ./arch/powerpc/include/asm/processor.h:39,
from ./include/linux/prefetch.h:15,
from drivers/net/ethernet/emulex/benet/be_main.c:14:
drivers/net/ethernet/emulex/benet/be_main.c: In function 'be_rx_cqs_create':
./include/asm-generic/getorder.h:54:9: warning: comparison is always
true due to limited range of data type [-Wtype-limits]
(((n) < (1UL << PAGE_SHIFT)) ? 0 : \
^
drivers/net/ethernet/emulex/benet/be_main.c:3138:33: note: in expansion
of macro 'get_order'
adapter->big_page_size = (1 << get_order(rx_frag_size)) * PAGE_SIZE;
^~~~~~~~~
Fix it by moving all of this multi-line macro into a proper function,
and killing __get_order() off.
[akpm@linux-foundation.org: remove __get_order() altogether]
[cai@lca.pw: v2]
Link: http://lkml.kernel.org/r/1564000166-31428-1-git-send-email-cai@lca.pw
Link: http://lkml.kernel.org/r/1563914986-26502-1-git-send-email-cai@lca.pw
Fixes: d66acc39c7 ("bitops: Optimise get_order()")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Bill Wendling <morbo@google.com>
Cc: James Y Knight <jyknight@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On my laptop most memcg kselftests were being skipped because it claimed
cgroup v2 hierarchy wasn't mounted, but this isn't correct. Instead, it
seems current systemd HEAD mounts it with the name "cgroup2" instead of
"cgroup":
% grep cgroup /proc/mounts
cgroup2 /sys/fs/cgroup cgroup2 rw,nosuid,nodev,noexec,relatime,nsdelegate 0 0
I can't think of a reason to need to check fs_spec explicitly
since it's arbitrary, so we can just rely on fs_vfstype.
After these changes, `make TARGETS=cgroup kselftest` actually runs the
cgroup v2 tests in more cases.
Link: http://lkml.kernel.org/r/20190723210737.GA487@chrisdown.name
Signed-off-by: Chris Down <chris@chrisdown.name>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
return is unneeded in void function
Link: http://lkml.kernel.org/r/20190723130814.21826-1-houweitaoo@gmail.com
Signed-off-by: Weitao Hou <houweitaoo@gmail.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When CONFIG_MIGRATE_VMA_HELPER is enabled, migrate_vma() calls
migrate_vma_collect() which initializes a struct mm_walk but didn't
initialize mm_walk.pud_entry. (Found by code inspection) Use a C
structure initialization to make sure it is set to NULL.
Link: http://lkml.kernel.org/r/20190719233225.12243-1-rcampbell@nvidia.com
Fixes: 8763cb45ab ("mm/migrate: new memory migration helper for use with device memory")
Signed-off-by: Ralph Campbell <rcampbell@nvidia.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Save the offsets of the start of each argument to avoid having to update
pointers to each argument after every corename krealloc and to avoid
having to duplicate the memory for the dump command.
Executable names containing spaces were previously being expanded from
%e or %E and then split in the middle of the filename. This is
incorrect behaviour since an argument list can represent arguments with
spaces.
The splitting could lead to extra arguments being passed to the core
dump handler that it might have interpreted as options or ignored
completely.
Core dump handlers that are not aware of this Linux kernel issue will be
using %e or %E without considering that it may be split and so they will
be vulnerable to processes with spaces in their names breaking their
argument list. If their internals are otherwise well written, such as
if they are written in shell but quote arguments, they will work better
after this change than before. If they are not well written, then there
is a slight chance of breakage depending on the details of the code but
they will already be fairly broken by the split filenames.
Core dump handlers that are aware of this Linux kernel issue will be
placing %e or %E as the last item in their core_pattern and then
aggregating all of the remaining arguments into one, separated by
spaces. Alternatively they will be obtaining the filename via other
methods. Both of these will be compatible with the new arrangement.
A side effect from this change is that unknown template types (for
example %z) result in an empty argument to the dump handler instead of
the argument being dropped. This is a desired change as:
It is easier for dump handlers to process empty arguments than dropped
ones, especially if they are written in shell or don't pass each
template item with a preceding command-line option in order to
differentiate between individual template types. Most core_patterns in
the wild do not use options so they can confuse different template types
(especially numeric ones) if an earlier one gets dropped in old kernels.
If the kernel introduces a new template type and a core_pattern uses it,
the core dump handler might not expect that the argument can be dropped
in old kernels.
For example, this can result in security issues when %d is dropped in
old kernels. This happened with the corekeeper package in Debian and
resulted in the interface between corekeeper and Linux having to be
rewritten to use command-line options to differentiate between template
types.
The core_pattern for most core dump handlers is written by the handler
author who would generally not insert unknown template types so this
change should be compatible with all the core dump handlers that exist.
Link: http://lkml.kernel.org/r/20190528051142.24939-1-pabs3@bonedaddy.net
Fixes: 74aadce986 ("core_pattern: allow passing of arguments to user mode helper when core_pattern is a pipe")
Signed-off-by: Paul Wise <pabs3@bonedaddy.net>
Reported-by: Jakub Wilk <jwilk@jwilk.net> [https://bugs.debian.org/924398]
Reported-by: Paul Wise <pabs3@bonedaddy.net> [https://lore.kernel.org/linux-fsdevel/c8b7ecb8508895bf4adb62a748e2ea2c71854597.camel@bonedaddy.net/]
Suggested-by: Jakub Wilk <jwilk@jwilk.net>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ARM64 randdconfig builds regularly run into a build error, especially
when NUMA_BALANCING and SPARSEMEM are enabled but not SPARSEMEM_VMEMMAP:
#error "KASAN: not enough bits in page flags for tag"
The last-cpuid bits are already contitional on the available space, so
the result of the calculation is a bit random on whether they were
already left out or not.
Adding the kasan tag bits before last-cpuid makes it much more likely to
end up with a successful build here, and should be reliable for
randconfig at least, as long as that does not randomize NR_CPUS or
NODES_SHIFT but uses the defaults.
In order for the modified check to not trigger in the x86 vdso32 code
where all constants are wrong (building with -m32), enclose all the
definitions with an #ifdef.
[arnd@arndb.de: build fix]
Link: http://lkml.kernel.org/r/CAK8P3a3Mno1SWTcuAOT0Wa9VS15pdU6EfnkxLbDpyS55yO04+g@mail.gmail.com
Link: http://lkml.kernel.org/r/20190722115520.3743282-1-arnd@arndb.de
Link: https://lore.kernel.org/lkml/20190618095347.3850490-1-arnd@arndb.de/
Fixes: 2813b9c029 ("kasan, mm, arm64: tag non slab memory allocated via pagealloc")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
objtool points out several conditions that it does not like, depending
on the combination with other configuration options and compiler
variants:
stack protector:
lib/ubsan.o: warning: objtool: __ubsan_handle_type_mismatch()+0xbf: call to __stack_chk_fail() with UACCESS enabled
lib/ubsan.o: warning: objtool: __ubsan_handle_type_mismatch_v1()+0xbe: call to __stack_chk_fail() with UACCESS enabled
stackleak plugin:
lib/ubsan.o: warning: objtool: __ubsan_handle_type_mismatch()+0x4a: call to stackleak_track_stack() with UACCESS enabled
lib/ubsan.o: warning: objtool: __ubsan_handle_type_mismatch_v1()+0x4a: call to stackleak_track_stack() with UACCESS enabled
kasan:
lib/ubsan.o: warning: objtool: __ubsan_handle_type_mismatch()+0x25: call to memcpy() with UACCESS enabled
lib/ubsan.o: warning: objtool: __ubsan_handle_type_mismatch_v1()+0x25: call to memcpy() with UACCESS enabled
The stackleak and kasan options just need to be disabled for this file
as we do for other files already. For the stack protector, we already
attempt to disable it, but this fails on clang because the check is
mixed with the gcc specific -fno-conserve-stack option. According to
Andrey Ryabinin, that option is not even needed, dropping it here fixes
the stackprotector issue.
Link: http://lkml.kernel.org/r/20190722125139.1335385-1-arnd@arndb.de
Link: https://lore.kernel.org/lkml/20190617123109.667090-1-arnd@arndb.de/t/
Link: https://lore.kernel.org/lkml/20190722091050.2188664-1-arnd@arndb.de/t/
Fixes: d08965a27e ("x86/uaccess, ubsan: Fix UBSAN vs. SMAP")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
asan-stack mode still uses dangerously large kernel stacks of tens of
kilobytes in some drivers, and it does not seem that anyone is working
on the clang bug.
Turn it off for all clang versions to prevent users from accidentally
enabling it once they update to clang-9, and to help automated build
testing with clang-9.
Link: https://bugs.llvm.org/show_bug.cgi?id=38809
Link: http://lkml.kernel.org/r/20190719200347.2596375-1-arnd@arndb.de
Fixes: 6baec880d7 ("kasan: turn off asan-stack for clang-8 and earlier")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Qian Cai <cai@lca.pw>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"howaboutsynergy" reported via kernel buzilla number 204165 that
compact_zone_order was consuming 100% CPU during a stress test for
prolonged periods of time. Specifically the following command, which
should exit in 10 seconds, was taking an excessive time to finish while
the CPU was pegged at 100%.
stress -m 220 --vm-bytes 1000000000 --timeout 10
Tracing indicated a pattern as follows
stress-3923 [007] 519.106208: mm_compaction_isolate_migratepages: range=(0x70bb80 ~ 0x70bb80) nr_scanned=0 nr_taken=0
stress-3923 [007] 519.106212: mm_compaction_isolate_migratepages: range=(0x70bb80 ~ 0x70bb80) nr_scanned=0 nr_taken=0
stress-3923 [007] 519.106216: mm_compaction_isolate_migratepages: range=(0x70bb80 ~ 0x70bb80) nr_scanned=0 nr_taken=0
stress-3923 [007] 519.106219: mm_compaction_isolate_migratepages: range=(0x70bb80 ~ 0x70bb80) nr_scanned=0 nr_taken=0
stress-3923 [007] 519.106223: mm_compaction_isolate_migratepages: range=(0x70bb80 ~ 0x70bb80) nr_scanned=0 nr_taken=0
stress-3923 [007] 519.106227: mm_compaction_isolate_migratepages: range=(0x70bb80 ~ 0x70bb80) nr_scanned=0 nr_taken=0
stress-3923 [007] 519.106231: mm_compaction_isolate_migratepages: range=(0x70bb80 ~ 0x70bb80) nr_scanned=0 nr_taken=0
stress-3923 [007] 519.106235: mm_compaction_isolate_migratepages: range=(0x70bb80 ~ 0x70bb80) nr_scanned=0 nr_taken=0
stress-3923 [007] 519.106238: mm_compaction_isolate_migratepages: range=(0x70bb80 ~ 0x70bb80) nr_scanned=0 nr_taken=0
stress-3923 [007] 519.106242: mm_compaction_isolate_migratepages: range=(0x70bb80 ~ 0x70bb80) nr_scanned=0 nr_taken=0
Note that compaction is entered in rapid succession while scanning and
isolating nothing. The problem is that when a task that is compacting
receives a fatal signal, it retries indefinitely instead of exiting
while making no progress as a fatal signal is pending.
It's not easy to trigger this condition although enabling zswap helps on
the basis that the timing is altered. A very small window has to be hit
for the problem to occur (signal delivered while compacting and
isolating a PFN for migration that is not aligned to SWAP_CLUSTER_MAX).
This was reproduced locally -- 16G single socket system, 8G swap, 30%
zswap configured, vm-bytes 22000000000 using Colin Kings stress-ng
implementation from github running in a loop until the problem hits).
Tracing recorded the problem occurring almost 200K times in a short
window. With this patch, the problem hit 4 times but the task existed
normally instead of consuming CPU.
This problem has existed for some time but it was made worse by commit
cf66f0700c ("mm, compaction: do not consider a need to reschedule as
contention"). Before that commit, if the same condition was hit then
locks would be quickly contended and compaction would exit that way.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204165
Link: http://lkml.kernel.org/r/20190718085708.GE24383@techsingularity.net
Fixes: cf66f0700c ("mm, compaction: do not consider a need to reschedule as contention")
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org> [5.1+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
buffer_migrate_page_norefs() can race with bh users in the following
way:
CPU1 CPU2
buffer_migrate_page_norefs()
buffer_migrate_lock_buffers()
checks bh refs
spin_unlock(&mapping->private_lock)
__find_get_block()
spin_lock(&mapping->private_lock)
grab bh ref
spin_unlock(&mapping->private_lock)
move page do bh work
This can result in various issues like lost updates to buffers (i.e.
metadata corruption) or use after free issues for the old page.
This patch closes the race by holding mapping->private_lock while the
mapping is being moved to a new page. Ordinarily, a reference can be
taken outside of the private_lock using the per-cpu BH LRU but the
references are checked and the LRU invalidated if necessary. The
private_lock is held once the references are known so the buffer lookup
slow path will spin on the private_lock. Between the page lock and
private_lock, it should be impossible for other references to be
acquired and updates to happen during the migration.
A user had reported data corruption issues on a distribution kernel with
a similar page migration implementation as mainline. The data
corruption could not be reproduced with this patch applied. A small
number of migration-intensive tests were run and no performance problems
were noted.
[mgorman@techsingularity.net: Changelog, removed tracing]
Link: http://lkml.kernel.org/r/20190718090238.GF24383@techsingularity.net
Fixes: 89cb0888ca "mm: migrate: provide buffer_migrate_page_norefs()"
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Cc: <stable@vger.kernel.org> [5.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shakeel Butt reported premature oom on kernel with
"cgroup_disable=memory" since mem_cgroup_is_root() returns false even
though memcg is actually NULL. The drop_caches is also broken.
It is because commit aeed1d325d ("mm/vmscan.c: generalize
shrink_slab() calls in shrink_node()") removed the !memcg check before
!mem_cgroup_is_root(). And, surprisingly root memcg is allocated even
though memory cgroup is disabled by kernel boot parameter.
Add mem_cgroup_disabled() check to make reclaimer work as expected.
Link: http://lkml.kernel.org/r/1563385526-20805-1-git-send-email-yang.shi@linux.alibaba.com
Fixes: aeed1d325d ("mm/vmscan.c: generalize shrink_slab() calls in shrink_node()")
Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com>
Reported-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Jan Hadrava <had@kam.mff.cuni.cz>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Qian Cai <cai@lca.pw>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org> [4.19+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
fs/ocfs2/xattr.c: In function ocfs2_xattr_bucket_find:
fs/ocfs2/xattr.c:3828:6: warning: variable last_hash set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Link: http://lkml.kernel.org/r/20190716132110.34836-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When running ltp's oom test with kmemleak enabled, the below warning was
triggerred since kernel detects __GFP_NOFAIL & ~__GFP_DIRECT_RECLAIM is
passed in:
WARNING: CPU: 105 PID: 2138 at mm/page_alloc.c:4608 __alloc_pages_nodemask+0x1c31/0x1d50
Modules linked in: loop dax_pmem dax_pmem_core ip_tables x_tables xfs virtio_net net_failover virtio_blk failover ata_generic virtio_pci virtio_ring virtio libata
CPU: 105 PID: 2138 Comm: oom01 Not tainted 5.2.0-next-20190710+ #7
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.10.2-0-g5f4c7b1-prebuilt.qemu-project.org 04/01/2014
RIP: 0010:__alloc_pages_nodemask+0x1c31/0x1d50
...
kmemleak_alloc+0x4e/0xb0
kmem_cache_alloc+0x2a7/0x3e0
mempool_alloc_slab+0x2d/0x40
mempool_alloc+0x118/0x2b0
bio_alloc_bioset+0x19d/0x350
get_swap_bio+0x80/0x230
__swap_writepage+0x5ff/0xb20
The mempool_alloc_slab() clears __GFP_DIRECT_RECLAIM, however kmemleak
has __GFP_NOFAIL set all the time due to d9570ee3bd ("kmemleak:
allow to coexist with fault injection"). But, it doesn't make any sense
to have __GFP_NOFAIL and ~__GFP_DIRECT_RECLAIM specified at the same
time.
According to the discussion on the mailing list, the commit should be
reverted for short term solution. Catalin Marinas would follow up with
a better solution for longer term.
The failure rate of kmemleak metadata allocation may increase in some
circumstances, but this should be expected side effect.
Link: http://lkml.kernel.org/r/1563299431-111710-1-git-send-email-yang.shi@linux.alibaba.com
Fixes: d9570ee3bd ("kmemleak: allow to coexist with fault injection")
Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Qian Cai <cai@lca.pw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel-doc parser doesn't handle expressions with %foo*. Instead,
when an asterisk should be part of a constant, it uses an alternative
notation: `foo*`.
Link: http://lkml.kernel.org/r/7f18c2e0b5e39e6b7eb55ddeb043b8b260b49f2d.1563361575.git.mchehab+samsung@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cc: Deepa Dinamani <deepa.kernel@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "vqmmc-1-8-v" and "ocr-limit" properties are not documented
anywhere, so just remove them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Earlier, the PWM registers were included as part of the pinctrl memory
map, but this turned to be useless as the muxing is being handled by the
SoC pin controller itself. Hence, this commit removes the pwm register
mapping from the pinctrl node to make it more clean.
Fixes: af2ff87de413 ("arm64: dts: bitmain: Add pinctrl support for BM1880 SoC")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add reset controller support for Bitmain BM1880 SoC. This commit also
adds reset support to UART peripherals.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Add opp-suspend property to each OPP, the of opp core will
select the OPP HW supported and with highest rate to be
suspend opp, it will speed up the suspend/resume process.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add opp-suspend property to each OPP, the of opp core will
select the OPP HW supported and with highest rate to be
suspend opp, it will speed up the suspend/resume process.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since fsl-ls1088a Soc GPIO registers are used as little endian,
the patch adds the little-endian attribute to each gpio node.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the console device tree node for the following
DPAA2 based platforms: LS1088A, LS2080A, LS2088A and LX2160A.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TechNexion PICO-PI-IMX8M-DEV evaluation and development kit based on
NXP i.MX8M Quad applications processor. Datasheet can be found at:
https://s3.us-east-2.amazonaws.com/technexion/datasheets/picopiimx8m.pdf
The current level of support yields a working console and is able to boot
userspace from NFS or init ramdisk.
Additional subsystems that are active :
- Ethernet
- USB
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Andra Danciu <andradanciu1997@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch use the optional property node "arm,malidp-arqos-value" to
can be dynamic configure QoS signaling.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for i.MX8QXP AI_ML board from Einfochips. This board is one
of the Consumer Edition boards of the 96Boards family based on i.MX8QXP
SoC from NXP/Freescale.
The initial support includes following peripherals which are tested and
known to be working:
1. Debug serial via UART2
2. uSD
3. WiFi
4. Ethernet
More information about this board can be found in Arrow website:
https://www.arrow.com/en/products/imx8-ai-ml/arrow-development-tools
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All these at803x properties are not documented anywhere, so
just remove them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ls1046afrwy board is based on nxp ls1046a SoC.
Board support's 4GB ddr memory, i2c, microSD card,
serial console,qspi nor flash,ifc nand flash,qsgmii network interface,
usb 3.0 and serdes interface to support two x1gen3 pcie interface.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the charge controller node. With the controller driver loaded
the VBUS of the user USB socket is controlled exclusively via i2c
with the GPIO controls ignored, so vbus-supply for the user USB
port must be linked to the charge controller.
Hog the previously used GPIO control to unconditionally enable
VBUS until the driver is loaded.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct clock for "bus_early", "ref", "suspend" should be:
IMX8MQ_CLK_USB1_CTRL_ROOT, IMX8MQ_CLK_USB_CORE_REF, IMX8MQ_CLK_32K,
especially we may need the right suspend clock rate to set register
in controller driver.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MQ has clock gate for TMU module, add clock info to TMU
node for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to latest datasheet (Rev.1, 10/2018) from below links,
in the consumer datasheet, 1.5GHz is mentioned as highest opp but
depends on speed grading fuse, and in the industrial datasheet,
1.3GHz is mentioned as highest opp but depends on speed grading
fuse. 1.5GHz and 1.3GHz opp use same voltage, so no need for
consumer part to support 1.3GHz opp, with same voltage, CPU should
run at highest frequency in order to go into idle as quick as
possible, this can save power.
That means for consumer part, 1GHz/1.5GHz are supported, for
industrial part, 800MHz/1.3GHz are supported, and then check the
speed grading fuse to limit the highest CPU frequency further.
Correct the market segment bits in opp table to make them work
according to datasheets.
https://www.nxp.com/docs/en/data-sheet/IMX8MDQLQIEC.pdfhttps://www.nxp.com/docs/en/data-sheet/IMX8MDQLQCEC.pdf
Fixes: 12629c5c37 ("arm64: dts: imx8mq: Add cpu speed grading and all OPPs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to latest datasheet (Rev.0.2, 04/2019) from below links,
1.8GHz is ONLY available for consumer part, so the market segment
bits for 1.8GHz opp should ONLY available for consumer part accordingly.
https://www.nxp.com/docs/en/data-sheet/IMX8MMIEC.pdfhttps://www.nxp.com/docs/en/data-sheet/IMX8MMCEC.pdf
Fixes: f403a26c86 (arm64: dts: imx8mm: Add cpu speed grading and all OPPs)
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The same ddr perfomance counter IP from 8qxp is also available on imx8m
series so add it to dts.
Tested with `perf stat` and `memtester` on imx8mm-evk and obtained
plausible results.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
USB1 port has typec connector with power delivery support:
- Dual data role: host and device.
- Dual power role: source and sink, prefer power sink.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since IMX8MM_CLK_USB_CORE_REF is not used at all, so remove the setting
for it.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX8MM pinctrl driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX8MQ pinctrl driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the initial configuration for clocks that need default parent and rate
setting. This is based on the vendor tree clock provider parents and rates
configuration except this is doing the setup in dts rather than using clock
consumer API in a clock provider driver.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The grain in EDAC is defined as "minimum granularity for an error
report, in bytes". The following calculation of the grain_bits in
edac_mc is wrong:
grain_bits = fls_long(e->grain) + 1;
Where grain_bits is defined as:
grain = 1 << grain_bits
Example:
grain = 8 # 64 bit (8 bytes)
grain_bits = fls_long(8) + 1
grain_bits = 4 + 1 = 5
grain = 1 << grain_bits
grain = 1 << 5 = 32
Replace it with the correct calculation:
grain_bits = fls_long(e->grain - 1);
The example gives now:
grain_bits = fls_long(8 - 1)
grain_bits = fls_long(7)
grain_bits = 3
grain = 1 << 3 = 8
Also, check if the hardware reports a reasonable grain != 0 and fallback
with a warning to 1 byte granularity otherwise.
[ bp: massage a bit. ]
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190624150758.6695-2-rrichter@marvell.com
This drops the check of the surplus "pads" configuration
from the device tree that is completely unused in the DRM
driver.
This was only used to work around limitations in the earlier
fbdev driver.
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190724134959.2365-2-linus.walleij@linaro.org
