- A series from Aisheng that improves SCU power domain bindings by
defining '#power-domain-cells' as 1, and adds i.MX8 SCU power domain
driver support on top of it.
- A series from Lucas that updates gpcv2 driver for scalability and
adds i.MX8MQ support into the driver.
- Increase gpc driver GPC_CLK_MAX definition to 7, as DISPLAY power
domain on imx6sx has 7 clocks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDbkEAAoJEFBXWFqHsHzO1C4H/05Khi/tWF6xZNMw7C4Q6wf6
WIFhB73tTLxZ8W0n8gIS+Y2YKFw6+dy8J/ZpkFBpe+f6rqVsyTzUvGB+6Ii3Nomu
V2juCn8XaHfv32FfaPBCelnitcpgFrnEvXYS6u8mSEt1DSu8rK2y2yMcnrkdcurq
Jy9eAYjUrdXYGsH9uw36mco7q25I5wSnXOLzZ0SLXSqB//a9YlzPKGRmQqF0uQ3t
K8uT5PwqEBrjNAP6sTvSzMf6vSeXD5MGqrEvd/LnGp6IPwx7R+z4Y+HUw/RtTIdg
rP1hAt3PLDD7Ibk+GHH5q/M2+9fI2dn2y44JXGOlQvqdmoLVg1vCpTLEj8OioFU=
=/3Mg
-----END PGP SIGNATURE-----
Merge tag 'imx-drivers-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/drivers
i.MX drivers change for 4.21:
- A series from Aisheng that improves SCU power domain bindings by
defining '#power-domain-cells' as 1, and adds i.MX8 SCU power domain
driver support on top of it.
- A series from Lucas that updates gpcv2 driver for scalability and
adds i.MX8MQ support into the driver.
- Increase gpc driver GPC_CLK_MAX definition to 7, as DISPLAY power
domain on imx6sx has 7 clocks.
* tag 'imx-drivers-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: gpc: Increase GPC_CLK_MAX to 7
soc: imx: gpcv2: add support for i.MX8MQ SoC
soc: imx: gpcv2: move register access table to domain data
soc: imx: gpcv2: prefix i.MX7 specific defines
firmware: imx: add SCU power domain driver
firmware: imx: add pm svc headfile
dt-bindings: fsl: scu: update power domain binding
firmware: imx: remove resource id enums
dt-bindings: imx: add scu resource id headfile
Signed-off-by: Olof Johansson <olof@lixom.net>
the global command engine (GCE) device using the
command queue driver (cmdq).
-----BEGIN PGP SIGNATURE-----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=FlvC
-----END PGP SIGNATURE-----
Merge tag 'v4.20-next-soc' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into next/drivers
add helper functions to create and send commands to
the global command engine (GCE) device using the
command queue driver (cmdq).
* tag 'v4.20-next-soc' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
soc: mediatek: Add Mediatek CMDQ helper
Signed-off-by: Olof Johansson <olof@lixom.net>
These changes update the BPMP ABI header and implement a new variant of
the BPMP firmware version tag query if supported.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAlwKfu0THHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zoTp4D/9bv3igTtqNNQdqIABfUiN98sfC4BKU
vu/RD4vTfMTF15o/Cod6OhC6ivBdsbQgFARuzED5E5wYFPfz7YrvM8kwJ99noDAL
bo10cawyAEd88GxE07YxLc5cos4wuB1KtWyTP+ewdRm82LxSFLFng42b/gVbHMvK
atVFgyvg4rLsvJmAsbWlXvRx0Le6dTFowSu6dXNFQltLrfIALhc4YDmwWwSaD1Od
k2B0Q0/3Pn3draKjPi5KUFO2A/M7XirG6iN4I2uJzx5fwWNc1Jsgdmd5bpROTRSa
0nzZDbLpo1eVHMhDDYTohuSvgCS3ZUd5jG95V9rj6tkS0zJqTz7s595FG+QcCbRP
xUDpAoNQVr7u8cIK0ChTbxVHegGx3rozJqUOuUqBIIPoSbMH/vzD/6GGvLgdzmes
je3WLnLekq8zQuwMKNMDXpz90zew+CR/LX2N8SQT1xGeXF14K5NlPHJ6jouKne2S
9xnVrTS0oHrCTdL2HMkezdeLOYzd+sR6QEgxPqtVubNVjfGEmcZbBXgf+RcrWCiC
acs9bsDdCSWKS8OMTGGJlZUEXoopFh9DZMo3ugl6CWoEZHfOpnzJxGhcDp0JLlmt
QGuotQo1pmoJn3Gij2RbgCB6rWzlUhJzUUsOhtzMsJlRd//xphRFKnuuAj53wm31
KOxtQDL/WzLBVQ==
=hyDw
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.21-firmware' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
firmware: tegra: Changes for v4.21-rc1
These changes update the BPMP ABI header and implement a new variant of
the BPMP firmware version tag query if supported.
* tag 'tegra-for-4.21-firmware' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
firmware: tegra: Use in-band messages for firmware version query
soc/tegra: bpmp: Update ABI header
firmware: tegra: Print version tag at full
firmware: tegra: Switch to global mrq_is_supported()
firmware: tegra: Add helper to check for supported MRQs
Signed-off-by: Olof Johansson <olof@lixom.net>
These changes are mostly cleanups to the PMC driver, but they also add
support for wake events on Tegra186 and Tegra194, which can be used to
wake the system from sleep. With this and the corresponding device
tree additions suspend/resume is finally working on these SoCs.
-----BEGIN PGP SIGNATURE-----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=lNWz
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.21-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
soc/tegra: Changes for v4.21-rc1
These changes are mostly cleanups to the PMC driver, but they also add
support for wake events on Tegra186 and Tegra194, which can be used to
wake the system from sleep. With this and the corresponding device
tree additions suspend/resume is finally working on these SoCs.
* tag 'tegra-for-4.21-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Add initial Tegra194 wake events
soc/tegra: pmc: Add initial Tegra186 wake events
soc/tegra: pmc: Add wake event support
soc/tegra: pmc: Add Tegra194 support
soc/tegra: pmc: Change to use DEFINE_SHOW_ATTRIBUTE macro
soc/tegra: Don't leak device tree node reference
soc/tegra: fuse: Remove duplicated function declaration
soc/tegra: pmc: Drop locking from tegra_powergate_is_powered()
soc/tegra: pmc: Add sysfs entries for reset info
soc/tegra: pmc: Don't power-up XUSB power-domains
Signed-off-by: Olof Johansson <olof@lixom.net>
dmaengine conversion.
-----BEGIN PGP SIGNATURE-----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=JuG5
-----END PGP SIGNATURE-----
Merge tag 'pxa-for-4.21' of https://github.com/rjarzmik/linux into next/drivers
This pxa update brings only a single patch, finishing the
dmaengine conversion.
* tag 'pxa-for-4.21' of https://github.com/rjarzmik/linux:
dmaengine: pxa: make the filter function internal
Signed-off-by: Olof Johansson <olof@lixom.net>
Highlights
- add CPU OPP tables
- timers: add global timer and TWD
-----BEGIN PGP SIGNATURE-----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=qoPa
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt-2' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
ARM: dts: Amlogic updates for v4.21, round 2
Highlights
- add CPU OPP tables
- timers: add global timer and TWD
* tag 'amlogic-dt-2' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson: meson8b: add the CPU OPP tables
ARM: dts: meson: meson8: add the CPU OPP table
ARM: dts: meson8b: add the Cortex-A5 global timer
ARM: dts: meson8b: add the ARM TWD timer
ARM: dts: meson8: add the Cortex-A9 global timer
ARM: dts: meson8: add the ARM TWD timer
ARM: dts: meson: group the Cortex-A5 / Cortex-A9 peripherals
dt-bindings: clock: meson8b: export the CPU post dividers
Signed-off-by: Olof Johansson <olof@lixom.net>
- It includes the initial device tree for i.MX7ULP SoC and EVK board
support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDd7aAAoJEFBXWFqHsHzOgNEIAKc4dqYzWmfJTMnJGO+Bb1Rc
BPkENpRWk6rWVBuxXwN4MTupXIgj96bBHWsg3kplgcthMRAl2wgomHTpNWXk8R9m
Fn6sH9yIoeqr+xs6BzzQ8COrFBXg8CEZgKLgy+9nhfFi3xNf6pN6IQLgqrGF17MC
zFH+sM0rqlh1l3BfHXMuwHvbhw+ms6Qo6z68OGSXmu0bUPThm2FV/Akivqp+INSI
CeFyZ8RMTkEKVSkFEryZaprKgqlIYW2Kl54yeALjvG03mtn1onaZKqsNV7YonYMC
X+mZPLnwjBUnLi2HbKrStmTR0ePQjg5x1tMT+Eco7Cjj4h6H6uBu0IYMi4PiN7o=
=aOId
-----END PGP SIGNATURE-----
Merge tag 'imx7ulp-dt-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX7ULP device tree for 4.21:
- It includes the initial device tree for i.MX7ULP SoC and EVK board
support.
* tag 'imx7ulp-dt-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx: add imx7ulp evk support
ARM: dts: imx: add common imx7ulp dtsi support
dt-bindings: fsl: add imx7ulp pm related components bindings
dt-bindings: fsl: add compatible for imx7ulp evk
clk: imx: add imx7ulp clk driver
clk: imx: implement new clk_hw based APIs
clk: imx: make mux parent strings const
dt-bindings: clock: add imx7ulp clock binding doc
clk: imx: add imx7ulp composite clk support
clk: imx: add pfdv2 support
clk: imx: add pllv4 support
clk: fractional-divider: add CLK_FRAC_DIVIDER_ZERO_BASED flag support
clk: imx: add gatable clock divider support
Signed-off-by: Olof Johansson <olof@lixom.net>
The regulator supports a dedicated suspend mode.
Implement the appropriate ->set_suspend_xx() hooks, add support for
->set_mode(), and provide basic PM ops functionalities to setup the
regulator in a suspend state when the system is entering suspend.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[claudiu.beznea@microchip.com: remove shutdown function, use dev_pm_ops,
fix checkpatch warning, adapt commit message, add LDO modes support,
move modes constants to active-semi,8945a-regulator.h, remove rdevs from
struct act8945a_pmic, add op_mode to act8945a_pmic]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make all the required change to start use the ib_device_ops structure.
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Fix up licensing to be inline with Linux conventions.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
So it looks like folks are interested in dwc3 again. Almost 64% of the
changes are in dwc3 this time around with some other bits in gadget
functions and dwc2.
There are two important parts here: a. removal of the waitqueue from
dwc3's dequeue implementation, which will guarantee that gadget
functions can dequeue from any context and; b. better method for
starting isochronous transfers to avoid, as much as possible, missed
isoc frames.
Apart from these, we have the usual set of non-critical fixes and new
features all over the place.
-----BEGIN PGP SIGNATURE-----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=n8VS
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB changes for v4.21
So it looks like folks are interested in dwc3 again. Almost 64% of the
changes are in dwc3 this time around with some other bits in gadget
functions and dwc2.
There are two important parts here: a. removal of the waitqueue from
dwc3's dequeue implementation, which will guarantee that gadget
functions can dequeue from any context and; b. better method for
starting isochronous transfers to avoid, as much as possible, missed
isoc frames.
Apart from these, we have the usual set of non-critical fixes and new
features all over the place.
* tag 'usb-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (56 commits)
usb: dwc2: Fix disable all EP's on disconnect
usb: dwc3: gadget: Disable CSP for stream OUT ep
usb: dwc2: disable power_down on Amlogic devices
Revert "usb: dwc3: pci: Use devm functions to get the phy GPIOs"
USB: gadget: udc: s3c2410_udc: convert to DEFINE_SHOW_ATTRIBUTE
usb: mtu3: fix dbginfo in qmu_tx_zlp_error_handler
usb: dwc3: trace: add missing break statement to make compiler happy
usb: dwc3: gadget: Report isoc transfer frame number
usb: gadget: Introduce frame_number to usb_request
usb: renesas_usbhs: Use SIMPLE_DEV_PM_OPS macro
usb: renesas_usbhs: Remove dummy runtime PM callbacks
usb: dwc2: host: use hrtimer for NAK retries
usb: mtu3: clear SOFTCONN when clear USB3_EN if work as HS mode
usb: mtu3: enable SETUPENDISR interrupt
usb: mtu3: fix the issue about SetFeature(U1/U2_Enable)
usb: mtu3: enable hardware remote wakeup from L1 automatically
usb: mtu3: remove QMU checksum
usb/mtu3: power down device ip at setup
usb: dwc2: Disable power down feature on Samsung SoCs
usb: dwc3: Correct the logic for checking TRB full in __dwc3_prepare_one_trb()
...
The API to configure a PWM using pwm_enable(), pwm_disable(),
pwm_config() and pwm_set_polarity() is superseeded by atomically setting
the parameters using pwm_apply_state(). To get forward with deprecating
the former set of functions use the opportunity that there is no current
user of pwm_set_polarity() and remove it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
*) Change phy set_mode ops to take both mode and setmode as arguments
*) Add phy_configure() and phy_validate() API's mostly used for MIPI D-PHY
*) Add helpers to get default values of parameters define in MIPI D-PHY spec
*) Add driver for TI's CPSW Port PHY Interface Mode selection
*) Add driver for Cadence Sierra PHY used with USB and PCIe
*) Add driver for Freescale i.MX8MQ USB3 PHY
*) Fixes QMP PHY bindings to allow the clocks provided by the PHY to be
pointed at in device tree
*) Fix for using fully specified regions (in device tree) for configuring
the second lane in dual lane PHYs in QMP PHY
*) Add support for Allwinner H6 USB2 PHY in phy-sun4i-usb driver
*) Update phy-rcar-gen3-usb driver to follow the hardware manual
*) Add support for fine grained power management in mapphone-mdm6600 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=JLIJ
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.21_v1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.21
*) Change phy set_mode ops to take both mode and setmode as arguments
*) Add phy_configure() and phy_validate() API's mostly used for MIPI D-PHY
*) Add helpers to get default values of parameters define in MIPI D-PHY spec
*) Add driver for TI's CPSW Port PHY Interface Mode selection
*) Add driver for Cadence Sierra PHY used with USB and PCIe
*) Add driver for Freescale i.MX8MQ USB3 PHY
*) Fixes QMP PHY bindings to allow the clocks provided by the PHY to be
pointed at in device tree
*) Fix for using fully specified regions (in device tree) for configuring
the second lane in dual lane PHYs in QMP PHY
*) Add support for Allwinner H6 USB2 PHY in phy-sun4i-usb driver
*) Update phy-rcar-gen3-usb driver to follow the hardware manual
*) Add support for fine grained power management in mapphone-mdm6600 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-4.21_v1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (30 commits)
phy: qcom-qmp: Expose provided clocks to DT
dt-bindings: phy-qcom-qmp: Move #clock-cells to child
phy: qcom-qmp: Utilize fully-specified DT registers
dt-bindings: phy-qcom-qmp: Fix register underspecification
phy: ti: fix semicolon.cocci warnings
phy: dphy: Add configuration helpers
phy: Add MIPI D-PHY configuration options
phy: Add configuration interface
phy: Add MIPI D-PHY mode
phy: add driver for Freescale i.MX8MQ USB3 PHY
dt-bindings: phy: add binding for Freescale i.MX8MQ USB3 PHY
phy: Use of_node_name_eq for node name comparisons
net: ethernet: ti: cpsw: add support for port interface mode selection phy
dt-bindings: net: ti: cpsw: switch to use phy-gmii-sel phy
phy: ti: introduce phy-gmii-sel driver
dt-bindings: phy: add cpsw port interface mode selection phy bindings
phy: mvebu-cp110-comphy: fix spelling in structure name
phy: mapphone-mdm6600: Improve phy related runtime PM calls
phy: renesas: rcar-gen3-usb2: follow the hardware manual procedure
phy: cadence: Add driver for Sierra PHY
...
The MIPI D-PHY spec defines default values and boundaries for most of the
parameters it defines. Introduce helpers to help drivers get meaningful
values based on their current parameters, and validate the boundaries of
these parameters if needed.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Now that we have some infrastructure for it, allow the MIPI D-PHY phy's to
be configured through the generic functions through a custom structure
added to the generic union.
The parameters added here are the ones defined in the MIPI D-PHY spec, plus
the number of lanes in use. The current set of parameters should cover all
the potential users.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The phy framework is only allowing to configure the power state of the PHY
using the init and power_on hooks, and their power_off and exit
counterparts.
While it works for most, simple, PHYs supported so far, some more advanced
PHYs need some configuration depending on runtime parameters. These PHYs
have been supported by a number of means already, often by using ad-hoc
drivers in their consumer drivers.
That doesn't work too well however, when a consumer device needs to deal
with multiple PHYs, or when multiple consumers need to deal with the same
PHY (a DSI driver and a CSI driver for example).
So we'll add a new interface, through two funtions, phy_validate and
phy_configure. The first one will allow to check that a current
configuration, for a given mode, is applicable. It will also allow the PHY
driver to tune the settings given as parameters as it sees fit.
phy_configure will actually apply that configuration in the phy itself.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
MIPI D-PHY is a MIPI standard meant mostly for display and cameras in
embedded systems. Add a mode for it.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
After recent changes PHY_MODE_SGMII, PHY_MODE_2500SGMII, PHY_MODE_QSGMII,
PHY_MODE_10GKR are not used any more and can be removed. Hence - remove
them.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add new PHY's mode to be used by Ethernet PHY interface drivers or
multipurpose PHYs like serdes. It will be reused in further changes.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently the attempt to add support for Ethernet interface mode PHY
(MII/GMII/RGMII) will lead to the necessity of extending enum phy_mode and
duplicate there values from phy_interface_t enum (or introduce more PHY
callbacks) [1]. Both approaches are ineffective and would lead to fast
bloating of enum phy_mode or struct phy_ops in the process of adding more
PHYs for different subsystems which will make them unmaintainable.
As discussed in [1] the solution could be to introduce dual level PHYs mode
configuration - PHY mode and PHY submode. The PHY mode will define generic
PHY type (subsystem - PCIE/ETHERNET/USB_) while the PHY submode - subsystem
specific interface mode. The last is usually already defined in
corresponding subsystem headers (phy_interface_t for Ethernet, enum
usb_device_speed for USB).
This patch is cumulative change which refactors PHY framework code to
support dual level PHYs mode configuration - PHY mode and PHY submode. It
extends .set_mode() callback to support additional parameter "int submode"
and converts all corresponding PHY drivers to support new .set_mode()
callback declaration.
The new extended PHY API
int phy_set_mode_ext(struct phy *phy, enum phy_mode mode, int submode)
is introduced to support dual level PHYs mode configuration and existing
phy_set_mode() API is converted to macros, so PHY framework consumers do
not need to be changed (~21 matches).
[1] http://lkml.kernel.org/r/d63588f6-9ab0-848a-5ad4-8073143bd95d@ti.com
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Michael and Sandipan report:
Commit ede95a63b5 introduced a bpf_jit_limit tuneable to limit BPF
JIT allocations. At compile time it defaults to PAGE_SIZE * 40000,
and is adjusted again at init time if MODULES_VADDR is defined.
For ppc64 kernels, MODULES_VADDR isn't defined, so we're stuck with
the compile-time default at boot-time, which is 0x9c400000 when
using 64K page size. This overflows the signed 32-bit bpf_jit_limit
value:
root@ubuntu:/tmp# cat /proc/sys/net/core/bpf_jit_limit
-1673527296
and can cause various unexpected failures throughout the network
stack. In one case `strace dhclient eth0` reported:
setsockopt(5, SOL_SOCKET, SO_ATTACH_FILTER, {len=11, filter=0x105dd27f8},
16) = -1 ENOTSUPP (Unknown error 524)
and similar failures can be seen with tools like tcpdump. This doesn't
always reproduce however, and I'm not sure why. The more consistent
failure I've seen is an Ubuntu 18.04 KVM guest booted on a POWER9
host would time out on systemd/netplan configuring a virtio-net NIC
with no noticeable errors in the logs.
Given this and also given that in near future some architectures like
arm64 will have a custom area for BPF JIT image allocations we should
get rid of the BPF_JIT_LIMIT_DEFAULT fallback / default entirely. For
4.21, we have an overridable bpf_jit_alloc_exec(), bpf_jit_free_exec()
so therefore add another overridable bpf_jit_alloc_exec_limit() helper
function which returns the possible size of the memory area for deriving
the default heuristic in bpf_jit_charge_init().
Like bpf_jit_alloc_exec() and bpf_jit_free_exec(), the new
bpf_jit_alloc_exec_limit() assumes that module_alloc() is the default
JIT memory provider, and therefore in case archs implement their custom
module_alloc() we use MODULES_{END,_VADDR} for limits and otherwise for
vmalloc_exec() cases like on ppc64 we use VMALLOC_{END,_START}.
Additionally, for archs supporting large page sizes, we should change
the sysctl to be handled as long to not run into sysctl restrictions
in future.
Fixes: ede95a63b5 ("bpf: add bpf_jit_limit knob to restrict unpriv allocations")
Reported-by: Sandipan Das <sandipan@linux.ibm.com>
Reported-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch introduces a means for syscalls matched in seccomp to notify
some other task that a particular filter has been triggered.
The motivation for this is primarily for use with containers. For example,
if a container does an init_module(), we obviously don't want to load this
untrusted code, which may be compiled for the wrong version of the kernel
anyway. Instead, we could parse the module image, figure out which module
the container is trying to load and load it on the host.
As another example, containers cannot mount() in general since various
filesystems assume a trusted image. However, if an orchestrator knows that
e.g. a particular block device has not been exposed to a container for
writing, it want to allow the container to mount that block device (that
is, handle the mount for it).
This patch adds functionality that is already possible via at least two
other means that I know about, both of which involve ptrace(): first, one
could ptrace attach, and then iterate through syscalls via PTRACE_SYSCALL.
Unfortunately this is slow, so a faster version would be to install a
filter that does SECCOMP_RET_TRACE, which triggers a PTRACE_EVENT_SECCOMP.
Since ptrace allows only one tracer, if the container runtime is that
tracer, users inside the container (or outside) trying to debug it will not
be able to use ptrace, which is annoying. It also means that older
distributions based on Upstart cannot boot inside containers using ptrace,
since upstart itself uses ptrace to monitor services while starting.
The actual implementation of this is fairly small, although getting the
synchronization right was/is slightly complex.
Finally, it's worth noting that the classic seccomp TOCTOU of reading
memory data from the task still applies here, but can be avoided with
careful design of the userspace handler: if the userspace handler reads all
of the task memory that is necessary before applying its security policy,
the tracee's subsequent memory edits will not be read by the tracer.
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
CC: Kees Cook <keescook@chromium.org>
CC: Andy Lutomirski <luto@amacapital.net>
CC: Oleg Nesterov <oleg@redhat.com>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: "Serge E. Hallyn" <serge@hallyn.com>
Acked-by: Serge Hallyn <serge@hallyn.com>
CC: Christian Brauner <christian@brauner.io>
CC: Tyler Hicks <tyhicks@canonical.com>
CC: Akihiro Suda <suda.akihiro@lab.ntt.co.jp>
Signed-off-by: Kees Cook <keescook@chromium.org>
The const qualifier causes problems for any code that wants to write to the
third argument of the seccomp syscall, as we will do in a future patch in
this series.
The third argument to the seccomp syscall is documented as void *, so
rather than just dropping the const, let's switch everything to use void *
as well.
I believe this is safe because of 1. the documentation above, 2. there's no
real type information exported about syscalls anywhere besides the man
pages.
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
CC: Kees Cook <keescook@chromium.org>
CC: Andy Lutomirski <luto@amacapital.net>
CC: Oleg Nesterov <oleg@redhat.com>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: "Serge E. Hallyn" <serge@hallyn.com>
Acked-by: Serge Hallyn <serge@hallyn.com>
CC: Christian Brauner <christian@brauner.io>
CC: Tyler Hicks <tyhicks@canonical.com>
CC: Akihiro Suda <suda.akihiro@lab.ntt.co.jp>
Signed-off-by: Kees Cook <keescook@chromium.org>
PPCNT is not supported if PCAM access reg is supported and ppcnt bit is clear.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Writing 64B CQEs to 128B cache lines results in a RMW operation. Padding
the CQEs to 128B if possible improves performance on 128B cache line
systems like PPC.
Testing on PPC showed up to a 24% improvement in small packet throughput
vs the default behavior, depending on the workload and system topology.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This change introduces the ib_device_ops structure that defines all the
InfiniBand device operations in one place, so the code will be more
readable and clean, unlike today when the ops are mixed with ib_device
data members.
The providers will need to define the supported operations and assign them
using ib_set_device_ops(), that will also make the providers code more
readable and clean.
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
IB representors don't support creation of RAW ethernet QP flows. Disable
them by reusing existing RDMA/core support macros. We do it for both
creation and matcher because latter is not usable if no flow creation is
available.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
CapabilityMask2 exists when IB_PORT_CAP_MASK2_SUP is set in the original
capability mask. In such cases, query its value and report it in query
port.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add the new rates that were added to Infiniband spec as part of HDR and 2x
support.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add the new 2X port width that is part of IB spec 1.3
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
CapabilityMask2 was added in IB Spec 1.3 under PortInfo attribute. The
new Capapbility mask is needed in order to expose the new 2X width and HDR
speed.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Currently pblk only check the size of I/O metadata and does not take
into account if this metadata is in a separate buffer or interleaved
in a single metadata buffer.
In reality only the first scenario is supported, where second mode will
break pblk functionality during any IO operation.
This patch prevents pblk to be instantiated in case device only
supports interleaved metadata.
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Igor Konopko <igor.j.konopko@intel.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently lightnvm and pblk uses single DMA pool, for which the entry
size always is equal to PAGE_SIZE. The contents of each entry allocated
from the DMA pool consists of a PPA list (8bytes * 64), leaving
56bytes * 64 space for metadata. Since the metadata field can be bigger,
such as 128 bytes, the static size does not cover this use-case.
This patch adds support for I/O metadata above 56 bytes by changing DMA
pool size based on device meta size and allows pblk to use OOB metadata
>=16B.
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Igor Konopko <igor.j.konopko@intel.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Minor markup fixup from bpf-next into net-next merge in the BPF helper
description of bpf_sk_lookup_tcp() and bpf_sk_lookup_udp(). Also sync
up the copy of bpf.h from tooling infrastructure.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To lower CPU overhead, future userspace will be switching to pinning
iova and avoiding the use of relocs, and only include cmds table entries
for IB1 level cmdstream (but not IB2 or state-groups).
This leaves the kernel unsure what to dump for rd/hangrd cmdstream
dumping. So add a MSM_SUBMIT_BO_DUMP flag so userspace can indicate
buffers that contain cmdstream (or are otherwise important to dump).
Signed-off-by: Rob Clark <robdclark@gmail.com>
This completes "drm/syncobj: Drop add/remove_callback from driver
interface" and cleans up the implementation a bit.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Link: https://patchwork.freedesktop.org/patch/266255/
This contains a few cleanups of and additions to existing device tree
bindings, such as XUSB, EMC, PMC and thermal.
-----BEGIN PGP SIGNATURE-----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=3PUd
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.21-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
dt-bindings: Changes for v4.21-rc1
This contains a few cleanups of and additions to existing device tree
bindings, such as XUSB, EMC, PMC and thermal.
* tag 'tegra-for-4.21-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: tegra186-pmc: Add interrupt controller properties
dt-bindings: thermal: tegra-bpmp: Add Tegra194 support
dt: bindings: Move tegra20-emc binding to memory-controllers directory
dt: bindings: tegra20-emc: Document clock property
dt: bindings: tegra20-emc: Document interrupt property
dt-bindings: usb: xhci-tegra: Add power-domain details
Signed-off-by: Olof Johansson <olof@lixom.net>
Several subsystems in the kernel (task scheduler and/or thermal at the
time of writing) can benefit from knowing about the energy consumed by
CPUs. Yet, this information can come from different sources (DT or
firmware for example), in different formats, hence making it hard to
exploit without a standard API.
As an attempt to address this, introduce a centralized Energy Model
(EM) management framework which aggregates the power values provided
by drivers into a table for each performance domain in the system. The
power cost tables are made available to interested clients (e.g. task
scheduler or thermal) via platform-agnostic APIs. The overall design
is represented by the diagram below (focused on Arm-related drivers as
an example, but applicable to any architecture):
+---------------+ +-----------------+ +-------------+
| Thermal (IPA) | | Scheduler (EAS) | | Other |
+---------------+ +-----------------+ +-------------+
| | em_pd_energy() |
| | em_cpu_get() |
+-----------+ | +--------+
| | |
v v v
+---------------------+
| |
| Energy Model |
| |
| Framework |
| |
+---------------------+
^ ^ ^
| | | em_register_perf_domain()
+----------+ | +---------+
| | |
+---------------+ +---------------+ +--------------+
| cpufreq-dt | | arm_scmi | | Other |
+---------------+ +---------------+ +--------------+
^ ^ ^
| | |
+--------------+ +---------------+ +--------------+
| Device Tree | | Firmware | | ? |
+--------------+ +---------------+ +--------------+
Drivers (typically, but not limited to, CPUFreq drivers) can register
data in the EM framework using the em_register_perf_domain() API. The
calling driver must provide a callback function with a standardized
signature that will be used by the EM framework to build the power
cost tables of the performance domain. This design should offer a lot of
flexibility to calling drivers which are free of reading information
from any location and to use any technique to compute power costs.
Moreover, the capacity states registered by drivers in the EM framework
are not required to match real performance states of the target. This
is particularly important on targets where the performance states are
not known by the OS.
The power cost coefficients managed by the EM framework are specified in
milli-watts. Although the two potential users of those coefficients (IPA
and EAS) only need relative correctness, IPA specifically needs to
compare the power of CPUs with the power of other components (GPUs, for
example), which are still expressed in absolute terms in their
respective subsystems. Hence, specifying the power of CPUs in
milli-watts should help transitioning IPA to using the EM framework
without introducing new problems by keeping units comparable across
sub-systems.
On the longer term, the EM of other devices than CPUs could also be
managed by the EM framework, which would enable to remove the absolute
unit. However, this is not absolutely required as a first step, so this
extension of the EM framework is left for later.
On the client side, the EM framework offers APIs to access the power
cost tables of a CPU (em_cpu_get()), and to estimate the energy
consumed by the CPUs of a performance domain (em_pd_energy()). Clients
such as the task scheduler can then use these APIs to access the shared
data structures holding the Energy Model of CPUs.
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: adharmap@codeaurora.org
Cc: chris.redpath@arm.com
Cc: currojerez@riseup.net
Cc: dietmar.eggemann@arm.com
Cc: edubezval@gmail.com
Cc: gregkh@linuxfoundation.org
Cc: javi.merino@kernel.org
Cc: joel@joelfernandes.org
Cc: juri.lelli@redhat.com
Cc: morten.rasmussen@arm.com
Cc: patrick.bellasi@arm.com
Cc: pkondeti@codeaurora.org
Cc: skannan@codeaurora.org
Cc: smuckle@google.com
Cc: srinivas.pandruvada@linux.intel.com
Cc: thara.gopinath@linaro.org
Cc: tkjos@google.com
Cc: valentin.schneider@arm.com
Cc: vincent.guittot@linaro.org
Cc: viresh.kumar@linaro.org
Link: https://lkml.kernel.org/r/20181203095628.11858-4-quentin.perret@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
