Some SoCs, such as H6, doesn't have a full-featured TCON TOP.
Add quirks support for TCON TOP.
Currently the presence of TCON_TV1 and DSI is controlled via the quirks
structure.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Fixed code style and removed unnecessary initialization]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-25-jernej.skrabec@siol.net
It turns out that TCON TOP registers in H6 SoC have non-zero reset
value. This may cause issues if bits are not changed during
configuration.
To prevent that, initialize registers to 0.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-24-jernej.skrabec@siol.net
H6 has Synopsys DWC HDMI 2.0 TX PHY.
There is no freely available documentation for it, only code found in
BSP kernel. However, judging by the code, PHY is very similar to older
Synopsys HDMI PHY described in i.MX6 documentation. Most registers seem
to be the same.
According to i.MX6 documentation, mpll settings are based on pixel clock
and are not specific to each SoC. Because of that, mpll table in this
commit is based on that documentation and not on BSP code. Other PHY
settings were derived from BSP PHY driver code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-23-jernej.skrabec@siol.net
Currently sun8i-hdmi-phy driver supports only custom PHYs connected to
DW HDMI controller. Since newest Allwinner SoCs have unmodified Synopsys
PHY, driver has to be reorganized to support them.
Variant structure is expanded to allow differentiation between custom
and Sysnopsys PHYs and to hold Synopsys PHY settings.
Since DW HDMI bridge platform data has different fields for custom and
Sysnopsys PHY, function sun8i_hdmi_phy_get_ops() is replaced with
sun8i_hdmi_phy_set_ops().
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-22-jernej.skrabec@siol.net
Currently, quirks and compatibles are sorted alphabetically. However,
they should be sorted by family release date and then alphabetically.
Fix that by moving A64 quirks and compatible to bottom. No functional
change is made.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-21-jernej.skrabec@siol.net
It turns out that H6 HDMI BSP kernel driver doesn't change TMDS rate at
all. At this point it is not clear whether it is just not necessary or
it would cause some kind of issues.
Add a quirk for it.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-18-jernej.skrabec@siol.net
Since it is not possible to access sun8i-dw-hdmi driver private data
inside mode_valid function, make it configurable. That way different
versions of HDMI controllers can set different function, depending on
it's limitations.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-17-jernej.skrabec@siol.net
Currently supported Allwinner SoCs with DW HDMI controller have
scrambled addresses and read lock. However, that is not true in general.
For example, A80 and H6 have normal addresses and normal read access.
Move code for unscrambling addresses and unlocking read access to it's
own function and call it from init function.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-16-jernej.skrabec@siol.net
It turns out that even new DW HDMI controllers exhibits same magenta
line issues as older versions.
Enable workaround for v2.12a.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-15-jernej.skrabec@siol.net
Mixer 0 has 1 VI and 3 UI planes, scaler on all planes and can output
4K image @60Hz. It also support 10 bit colors, which are not yet
implemented.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-14-jernej.skrabec@siol.net
Display Engine 3 is an upgrade of DE2 with new features like support for
10 bit color formats and support for AFBC.
Most of DE2 code works with DE3, except some small details.
Implement basic support for DE3. Support for 10 bit colort formats and
AFBC, among others missing features, will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/260238/
Most, if not all, registers found in DE2 still exists in DE3. However,
units are on different base addresses.
To prepare for addition of DE3 support, registers macros are reworked so
they take base address as parameter.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[rebased]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-10-jernej.skrabec@siol.net
Since connectors can be created dynamically, fbdev should be initialized
even if there are no connectors at the moment. Otherwise fbdev will
not be created even after connector's appearance.
The patch fixes lack of fbdev on rinato and trats boards.
Fixes: 6afb7721e2 ("drm/exynos: move connector creation to attach callback")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DSI device can be attached after DRM device is registered. In such
case newly created connector must be registered by exynos_dsi.
The patch fixes exynos_drm on rinato and trats boards.
Fixes: 6afb7721e2 ("drm/exynos: move connector creation to attach callback")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This reverts commit 0586feba32
This patch makes it to need get_vblank_counter callback in crtc
to get frame counter from decon driver.
However, drm_dev->max_vblank_count is a member unique to
vendor's DRM driver but in case of ARM DRM, some CRTC devices
don't provide the frame counter value. As a result, this patch
made extension and clone mode not working.
Instead of this patch, we may need separated max_vblank_count
which belongs to each CRTC device, or need to implement frame
counter emulation for them who don't support HW frame counter.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The of_drm_find_panel() function returns error pointers and never NULL
but we the driver assumes that ->panel is NULL when it's not present.
Fixes: 6afb7721e2 ("drm/exynos: move connector creation to attach callback")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Similar to DSC DPCD registers, let us cache
FEC_CAPABLE register to avoid using stale
values. With this we can avoid aux reads
everytime and instead read the cached values.
v2: Avoid using memset and array for a single
field. (Manasi,Jani)
v3: Print FEC CAPABILITY value. (Manasi)
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102041455.15818-1-anusha.srivatsa@intel.com
Leases are entirely implemented within drm.ko, no need to even tempt
drivers into doing nasty things. And if there's really a need, we can
always re-export these again.
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@gmail.com>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102143107.25722-1-daniel.vetter@ffwll.ch
Since the flags are being used to operate on a u64 variable, they too
need to be marked as such so that the inverses are full width (and not
zero extended on 32b kernels and bdw+).
Reported-by: Sergii Romantsov <sergii.romantsov@globallogic.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102161232.17742-2-chris@chris-wilson.co.uk
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJb2+C2AAoJEAx081l5xIa+tUYP/060xa9VeKe0M11fMCCkchNV
TQfPQ8avy2/Tt9Mlly/XPMuBZ6FCTVBsseCxIdzl4rZAfm0SDVaTB4Z7XBBplXkv
R50Je95Fyv0/lnUbagI5qRtc+O6xdkuNIMHWlRRWGlCEbFE2atey9R2yiq/1q2J9
4NcGjykJ7d1vCgMm/9/iV4pLrxrRSxvizO4mS+SQpJ/0fEwJSZSvKdKp9LU/LTgx
qZGSBegPkR+j6znsMkuPYxQtMrhz+Pr49qp7Qm6wQV/K2Y0z7CoHZFikvpMp38i5
MQfYE0yDN3pKm5THt+RjV8laPIpnh2z8bcotUCGcjFWtGHQBfyQ4IaXkDPujcD6m
vRm4hhxP9DvNCq5eWFz3vU2n8NWf54BYFF8dPxcoghRkE6VB2CGpr+o9dzxX16QJ
oEi2Ak3G7RXa8Hn/C9EOSs7yijjKD8GZ8gR5osmI10EitIH7mrG9Xghts5XlcIJj
Ls30t0jPavO+t8V2/1HYP2vfSNvi/X953+pQIdN8Rk2vp0ziFdstzLg6ai8E1Hvl
jyvOF3/xstwIP8nFvYaNHkly2iVRC3rgj4GDncSe2U6kt8N4/aA+FemUwXJKBbFN
hVwPZuSlrCw5TE7tO3ulJon4uAWH5WO/gIOMn0+e+pBLJtUXQtWAR+JC2D+RDZO9
V+V7GuHIbIV6xarCwLjx
=5lmL
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-11-02' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Pretty much a normal fixes pull pre-rc1, mostly amdgpu fixes, one i915
link training regression fix, and a couple of minor panel/bridge fixes
and a panel quirk"
* tag 'drm-next-2018-11-02' of git://anongit.freedesktop.org/drm/drm: (37 commits)
drm/amdgpu: revert "enable gfxoff in non-sriov and stutter mode by default"
drm/amd/pp: Print warning if od_sclk/mclk out of range
drm/amd/pp: Fix pp_sclk/mclk_od not work on Vega10
drm/amd/pp: Fix pp_sclk/mclk_od not work on smu7
drm/amd/powerplay: no MGPU fan boost enablement on DPM disabled
drm/amdgpu: Fix skipping hangged job reset during gpu recover.
drm/amd/powerplay: revise Vega20 pptable version check
drm/amd/display: set backlight level limit to 1
drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1
dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1
drm/bridge: ti-sn65dsi86: Remove the mystery delay
drm/panel: simple: Add "no-hpd" delay for Innolux TV123WAM
drm/panel: simple: Support panels with HPD where HPD isn't connected
dt-bindings: drm/panel: simple: Add no-hpd property
drm/edid: Add 6 bpc quirk for BOE panel.
drm/amdgpu: fix reporting of failed msg sent to SMU (v2)
drm/amdgpu: Fix compute ring 1.0.0 failure after reset
drm/amdgpu: fix VM leaf walking
drm/amdgpu: fix amdgpu_vm_fini
drm/amd/powerplay: commonize the API for retrieving current clocks
...
The registers DPCSSS,DPSP,DPMLE1 and DPPMS are all at an offset
from the base - which is the FLexi IO Adaptor. Lets follow the
offset calculation while accessing these registers.
v2:
- Follow spec for numbering - s/0/1(Lucas)
- s/FIA_1/FIA1_BASE (Anusha)
v3:
- Remove register offset defines. (Jani)
- Update comment. (Anusha)
v4: rebase. Remove comment.(Lucas)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101185557.29585-1-anusha.srivatsa@intel.com
Use the newly added "max bpc" connector property to limit pipe bpp.
V3: Use drm_connector_state to access the "max bpc" property
V4: Initialize the drm property, add suuport to DP(Ville)
V5: Use the property in the connector and fix CI failure(Ville)
V6: Use the core function to attach max_bpc property, remove the redundant
clamping of pipe bpp based on connector info
V7: Fix Checkpatch warnings
V9: Cleanup connected_sink_max_bpp and fix initial value in DP(Ville)
V12: Fix debug message(Ville)
V13: Remove the redundant check and simplify the check logic(Stan)
V14: Fix the check in connected_sink_max_bpp(Stan)
v15 (From Manasi): Add missing break (Stan)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Kishore Kadiyala <kishore.kadiyala@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023014400.16055-1-manasi.d.navare@intel.com
At times 12bpc HDMI cannot be driven due to faulty cables, dongles
level shifters etc. To workaround them we may need to drive the output
at a lower bpc. Currently the user space does not have a way to limit
the bpc. The default bpc to be programmed is decided by the driver and
is run against connector limitations.
Creating a new connector property "max bpc" in order to limit the bpc.
xrandr can make use of this connector property to make sure that bpc does
not exceed the configured value. This property can be used by userspace to
set the bpc.
V2: Initialize max_bpc to satisfy kms_properties
V3: Move the property to drm_connector
V4: Split drm and i915 components(Ville)
V5: Make the property per connector(Ville)
V6: Compare the requested bpc to connector bpc(Daniel)
Move the attach_property function to core(Ville)
V7: Fix checkpatch warnings
V8: Simplify the connector check code(Ville)
V9: Const display_info(Ville)
V10,V11: Fix CI issues.
V12: Add the Kernel documentation(Daniel)
V14: Crossreference the function name in the doc(Daniel)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Kishore Kadiyala <kishore.kadiyala@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Sunpeng Li <sunpeng.li@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181012184233.29250-1-radhakrishna.sripada@intel.com
Add tests that verify that drm_internal_framebuffer_create creates
buffers correctly by creating a dummy drm_device with a mock function
for the fb_create callback.
To decide if a buffer has been created or not it just checks if
fb_create callback has been called for the particular drm_mode_fb_cmd2
that's being tested.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101151051.1509-8-alexandru-cosmin.gheorghe@arm.com
If we want to be able to write drmselftests for non-static core
functions that are not intended to be used by drivers we need this
functions to be exported.
This adds a macro that is tied of CONFIG_DRM_DEBUG_SELFTEST, and uses
that to export drm_internal_framebuffer_create, in order for
subsequent patches to be able to test it.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101151051.1509-7-alexandru-cosmin.gheorghe@arm.com
Mali-DP implements a number of tiled yuv formats which are not
currently described in drm_fourcc.h.
This adds those definitions and describes their memory layout by
using the newly added char_per_block, block_w, block_h.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101151051.1509-3-alexandru-cosmin.gheorghe@arm.com
For some pixel formats .cpp structure in drm_format info it's not
enough to describe the peculiarities of the pixel layout, for example
tiled formats or packed formats at bit level.
What's implemented here is to add three new members to drm_format_info
that could describe such formats:
- char_per_block[3]
- block_w[3]
- block_h[3]
char_per_block will be put in a union alongside cpp, for transparent
compatibility with the existing format descriptions.
Regarding, block_w and block_h they are intended to be used through
their equivalent getters drm_format_info_block_width /
drm_format_info_block_height, the reason of the getters is to abstract
the fact that for normal formats block_w and block_h will be unset/0,
but the methods will be returning 1.
Additionally, convenience function drm_format_info_min_pitch had been
added that computes the minimum required pitch for a given pixel
format and buffer width.
Using that the following drm core functions had been updated to
generically handle both block and non-block formats:
- drm_fb_cma_get_gem_addr: for block formats it will just return the
beginning of the block.
- framebuffer_check: Use the newly added drm_format_info_min_pitch.
- drm_gem_fb_create_with_funcs: Use the newly added
drm_format_info_min_pitch.
- In places where is not expecting to handle block formats, like fbdev
helpers I just added some warnings in case the block width/height
are greater than 1.
Changes since v3:
- Add helper function for computing the minimum required pitch.
- Improve/cleanup documentation
Changes since v8:
- Fixed build on 32bits arm architectures, with:
- return DIV_ROUND_UP((u64)buffer_width * info->char_per_block[plane],
+ return DIV_ROUND_UP_ULL((u64)buffer_width * info->char_per_block[plane],
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101170055.5433-1-alexandru-cosmin.gheorghe@arm.com
Having failed any attempts at a more generic solution,
I fall back to the very specific solution: define a simple
panel for the ARM RTSM emulated platforms.
I am doing this so we can convert all old users from the
previous fbdev driver to the PL111 DRM driver.
This works fine as far as I can test, provided the
device tree for RTSM AEMv8 is augmented accordingly.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026111334.3365-1-linus.walleij@linaro.org
Although there's nothing crucial missing, it's been a long time since
the last backmerge. Catch up with drm-next.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch fixes the naming of the registers:
s/PIPE_DSS_CTL/ICL_PIPE_DSS_CTL
And also fix the hex values to lower case, to match
rest of the definitions.
Manasi noticed this with the patch that was merged.
v2: fix "Fixes" tag.
Fixes: 8b1b558d69 ("drm/i915/icl: Add DSS_CTL Registers")
Suggested-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101214216.8958-1-anusha.srivatsa@intel.com
Pull AFS updates from Al Viro:
"AFS series, with some iov_iter bits included"
* 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (26 commits)
missing bits of "iov_iter: Separate type from direction and use accessor functions"
afs: Probe multiple fileservers simultaneously
afs: Fix callback handling
afs: Eliminate the address pointer from the address list cursor
afs: Allow dumping of server cursor on operation failure
afs: Implement YFS support in the fs client
afs: Expand data structure fields to support YFS
afs: Get the target vnode in afs_rmdir() and get a callback on it
afs: Calc callback expiry in op reply delivery
afs: Fix FS.FetchStatus delivery from updating wrong vnode
afs: Implement the YFS cache manager service
afs: Remove callback details from afs_callback_break struct
afs: Commit the status on a new file/dir/symlink
afs: Increase to 64-bit volume ID and 96-bit vnode ID for YFS
afs: Don't invoke the server to read data beyond EOF
afs: Add a couple of tracepoints to log I/O errors
afs: Handle EIO from delivery function
afs: Fix TTL on VL server and address lists
afs: Implement VL server rotation
afs: Improve FS server rotation error handling
...
- Fix flickering at low backlight levels on some systems
- Fix some overclocking regressions
- Vega20 updates for
- GPU recovery fixes
- Disable gfxoff on RV as some sbios/fw combinations are not stable yet
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101151939.2828-1-alexander.deucher@amd.com
BIOS can leave the PLL to port mapping enabled, even if the
corresponding encoder is disabled. Disable the port mapping in this
case.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-9-imre.deak@intel.com
Most of the AUX_CH_CTL flags are concerned with DP AUX transfer
parameters. As opposed to this the flag specifying the thunderbolt vs.
non-thunderbolt mode of the port is not related to AUX transfers at all
(rather it's repurposed to enable either TBT or non-TBT PHY HW blocks).
The programming has to be done before enabling the corresponding AUX
power well, so make it part of the power well code.
v3:
- Use existing enable/disable helpers instead of opencoding. (Jose)
- Fix type of is_tc_tbt to remain a bitfield. (Lucas)
- Add comment describing the is_tc_tbt power well flag. (Lucas)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108548
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-8-imre.deak@intel.com
DDI/TypeC ports need the AUX power domain for main link functionality
even when they operate in HDMI static mode, so enable the power domain
for these ports too.
v4:
- Rebase on the upstream ICL pre_pll_enable change.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-7-imre.deak@intel.com
For DDI/TypeC ports the AUX power domain needs to be enabled before the
port's PLL is enabled, so move the enabling earlier accordingly.
v2:
- Preserve the pre_pll hook for GEN9_LP. (Ville)
v3:
- Add related BSpec entries to commit log. (Jose)
v4:
- Rebase on the upstream ICL pre_pll_enable change.
BSpec: 21750, 22243
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-6-imre.deak@intel.com
From ICL onwards the AUX power domain may change dynamically based on
whether a DDI/TypeC port is in thunderbolt or non-thunderbolt mode, so
use a helper function instead of a static field to get the current
domain.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-5-imre.deak@intel.com
