Hook up r8a774a1 Audio-DMAC nodes to the IPMMU-MP.
Based on work for the r8a7795 by Magnus Damm.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up r8a774a1 DMAC nodes to the IPMMUs. In particular SYS-DMAC0
gets tied to IPMMU-DS0, and SYS-DMAC1 and SYS-DMAC2 get tied to IPMMU-DS1.
Based on work for the r8a7796 by Magnus Damm.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a774a1 has a single FDP1 instance similar to r8a7796.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DU device to r8a774a1.dtsi in a disabled state.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a774a1 soc has 5 VSP instances similar to r8a7796.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The EK874 board comes with a TDA19988 chip on board, therefore
enable it in the defconfig.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PMIC IRQ line pin multiplexing configuration is missing from the DTs.
Since the line is configured correctly by default, the system works fine.
However, add the IRQ line pin multiplexing configuration for completeness.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The RZ/A2M EVB has a 48MHz clock attached to USB_X1.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add USB clock node. If present, this clock input must be 48MHz.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add ethernet aliases so u-boot can find the device nodes.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The RZ/A2M EVB supports 2 SD card slots. A micro SD slot on the CPU
board, and a full SD card slot on the sub board.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The RZ/A2M EVB sub board has 2 Ethernet jacks on it.
Set switch SW6_4 to ON to use Ethernet Ch-0
Set switch SW6_5 to ON to use Ethernet Ch-1
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI support for the R7S9210 (RZ/A2) SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add I2C support for the R7S9210 (RZ/A2) SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Ethernet support for the RZ/A2 SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add RSPI support for RZ/A2 SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
A 64-bit kernel built without CONFIG_MLONGCALLS (-mlong-calls compiler
option) usually fails to link because of unreachable functions. Try to
work around that linking issue by moving the *.init and *.exit text
segments closer to the main text segment. With that change those
segments now don't get freed at runtime any longer, but since we in most
cases run with huge-page enabled, we ignore the lost memory in
preference of better performance.
This change will not guarantee that every kernel config will now
sucessfully build with short calls and without linking issues.
Signed-off-by: Helge Deller <deller@gmx.de>
Since commit 350e88bad4 ("mm: memblock: make keeping memblock memory
opt-in rather than opt-out") the default behaviour is to discard memblock
data after init and the ARCH_DISCARD_MEMBLOCK is obsolete.
Remove it.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Helge Deller <deller@gmx.de>
The TERES-I has internal speakers (left, right), internal microphone
and a headset combo jack (headphones + mic), "CTIA" (android) pinout.
The headphone and mic detect lines of the A64 are connected properly,
but AFAIK currently unsupported by the driver.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
mmc1 node where wifi module is connected doesn't have properly defined
power supplies so wifi module is never powered up. Fix that by
specifying additional power supplies.
Additionally, this STB may have either Realtek or Broadcom based wifi
module. One based on Broadcom module also needs external clock to work
properly. Fix that by adding clock property to wifi_pwrseq node.
Fixes: e582b47a92 ("ARM: dts: sun8i-h3: Add dts for the Beelink X2 STB")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Recent measurements indicate that using 50us results in a reduced CPU
consumption, while still providing the benefit of halt polling. Let's
use 50us instead.
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The Bananapi M64 has a micro-USB connector with USB OTG support (that
is already enabled). VBUS from this connector is wired to the PMIC's
VBUS input.
Enable the PMIC's USB power supply on this board, and also hook it up
to the USB PHY.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AXP803 has a VBUS power input. Add a device node for it,
now that we support it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
WiFi is connected to mmc1 and the Bluetooth side is connected to UART1
in a 4 wire configuration. Same as the WiFi side, due to being the same
chip and package, DLDO2 provides overall power via VBAT, and DLDO4
provides I/O power via VDDIO. The RTC clock output provides the LPO low
power clock at 32.768 kHz.
This patch enables WiFi and Bluetooth on OrangePi Win boards and adds
missing LPO clock on the WiFi side. PCM connection also exists for
Bluetooth audio, but it's not used here.
Bluetooth UART speed is set to 1.5 MBaud in order to be able transmit
audio. While module supports even higher speeds, currently sunxi clock
driver doesn't support higher speed.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 SoC features tweakable VCC for PC, PD, PG, PL and PM
banks.
This patch adds supplies for these banks except PL bank. PL bank is
where PMIC is attached, and currently if a PMIC regulator is added
for it a dependency loop will happen.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Goodix GT911 CTP is bound with Oceanic 5205 5inMFD board.
The CTP connected to board with,
- SDA, SCK from i2c0
- GPIO-LD0 as AVDD28 supply
- PH4 gpio as interrupt pin
- PH11 gpio as reset pin
- X axis is inverted
- Y axis is inverted
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add Goodix GT5663 capacitive touch controller node on
Amarula A64-Relic board.
The CTP connected to board with,
- SDA, SCK from i2c1
- GPIO-LD0 as AVDD28 supply
- PH4 gpio as interrupt pin
- PH8 gpio as reset pin
- X axis is inverted
- Y axis is inverted
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
There is only one pinmuxing available for each I2C controller.
So, move pinctrl for i2c0, i2c1 from board dts files into SoC dtsi.
By moving these pinctrls the i2c1 node from Nanopi A64 just have a
status, which is disabled already so remove the entire node from it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that the regulators are tied to the GPIO bank, we can remove the
unneeded regulator-always-on in reg_aldo2
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART3 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, DLDO1 and
DLDO2 regulator outputs from the PMIC provide overall power via VBAT and
I/O power via VDDIO. The CLK_OUT_A clock output from the SoC provides
the LPO low power clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for
Bluetooth, but this is not covered here.
The LPO clock is fed from CLK_OUT_A, which needs to be muxed on pin
PI12. This can be represented in multiple ways. This patch puts the
pinctrl property in the pin controller node. This is due to limitations
in Linux, where pinmux settings, even the same one, can not be shared
by multiple devices. Thus we cannot put it in both the WiFi and
Bluetooth device nodes. Putting it the CCU node is another option, but
Linux's CCU driver does not handle pinctrl. Also the pin controller is
guaranteed to be initialized after the CCU, when clocks are available.
And any other devices that use muxed pins are guaranteed to be
initialized after the pin controller. Thus having the CLK_OUT_A pinmux
reference be in the pin controller node is a good choice without having
to deal with implementation issues.
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Just like the Bananapi M2 Ultra, enable the ahci controller and
the two regulators needed to activate it.
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This patch adds the hdmi nodes to the Bananapi M2 Berry, the same way it
was done to the Bananapi M2 Ultra
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Just like the Bananapi M2 Ultra, the Bananapi M2 Berry has a Realtek
RTL8211E RGMII PHY tied to the GMAC.
The PMIC's DC1SW output provides power for the PHY, while the ALDO2
output provides I/O voltages on both sides.
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The bananapi-m2-berry has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs, tie them to the pio
node.
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The bananapi-m2-ultra has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs, tie them to the pio
node.
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Sid contains speedbin information and temperature sensor
calibration information and more, which are important for SOC.
This patch enables CONFIG_NVMEM_SUNXI_SID by default.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Since commit 1e434b7032 ("ARM: imx: update the cpu power up timing
setting on i.mx6sx") some characters loss is noticed on i.MX6ULL UART
as reported by Christoph Niedermaier.
The intention of such commit was to increase the SW2ISO field for i.MX6SX
only, but since cpuidle-imx6sx is also used on i.MX6UL/i.MX6ULL this caused
unintended side effects on other SoCs.
Fix this problem by keeping the original SW2ISO value for i.MX6UL/i.MX6ULL
and only increase SW2ISO in the i.MX6SX case.
Cc: stable@vger.kernel.org
Fixes: 1e434b7032 ("ARM: imx: update the cpu power up timing setting on i.mx6sx")
Reported-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SX SDB board, vgen6 supplies vdd1p1/vdd2p5 LDO and
sw2 supplies vdd3p0 LDO, this patch assigns corresponding power
supply for vdd1p1/vdd2p5/vdd3p0 to avoid confusion by below log:
vdd1p1: supplied by regulator-dummy
vdd3p0: supplied by regulator-dummy
vdd2p5: supplied by regulator-dummy
With this patch, the power supply is more accurate:
vdd1p1: supplied by VGEN6
vdd3p0: supplied by SW2
vdd2p5: supplied by VGEN6
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SLL EVK board, sw2 supplies vdd3p0 LDO, this patch assigns
corresponding power supply for vdd3p0 to avoid confusion by below log:
vdd3p0: supplied by regulator-dummy
With this patch, the power supply is more accurate:
vdd3p0: supplied by SW2
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SL EVK board, sw2 supplies vdd1p1/vdd2p5/vdd3p0 LDO, this
patch assigns corresponding power supply for vdd1p1/vdd2p5/vdd3p0
to avoid confusion by below log:
vdd1p1: supplied by regulator-dummy
vdd3p0: supplied by regulator-dummy
vdd2p5: supplied by regulator-dummy
With this patch, the power supply is more accurate:
vdd1p1: supplied by SW2
vdd3p0: supplied by SW2
vdd2p5: supplied by SW2
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX7D SDB board, sw2 supplies 1p0d/1p2 LDO, this patch assigns
corresponding power supply for 1p0d/1p2 LDO to avoid confusion by
below log:
vdd1p0d: supplied by regulator-dummy
vdd1p2: supplied by regulator-dummy
With this patch, the power supply is more accurate:
vdd1p0d: supplied by SW2
vdd1p2: supplied by SW2
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6Q/DL SabreSD board, vgen5 supplies vdd1p1/vdd2p5 LDO and
sw2 supplies vdd3p0 LDO, this patch assigns corresponding power
supply for vdd1p1/vdd2p5/vdd3p0 to avoid confusion by below log:
vdd1p1: supplied by regulator-dummy
vdd3p0: supplied by regulator-dummy
vdd2p5: supplied by regulator-dummy
With this patch, the power supply is more accurate:
vdd1p1: supplied by VGEN5
vdd3p0: supplied by SW2
vdd2p5: supplied by VGEN5
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The BUCK2 regulator is used for cpufreq voltage control, otherwise
configuration is mostly static.
This uses the newly-implemented rohm,reset-snvs-powered property to
properly handle the SNVS state of imx8mm.
Between BD71837 and BD71847 the BUCK3/4 regulators were removed but
datasheet and board schematics kept the names for BUCK5/6/7/8. The
driver however renumbered 5/6/7/8 to 3/4/5/6. Use the names from DT
bindings and add comments to signal this.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
CoreSight DT bindings have been updated, thus the old compatible strings
are obsolete and the drivers will report warning if DTS uses these
obsolete strings.
This patch switches to the new bindings for CoreSight dynamic funnel and
static replicator, so can dismiss warning during initialisation.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
During randconfig builds, I occasionally run into an invalid configuration
drivers/soc/imx/soc-imx8.o: In function `imx8_soc_init':
soc-imx8.c:(.init.text+0x144): undefined reference to `soc_device_register'
while CONFIG_SOC_BUS is not set, the building failed like this. This patch
selects SOC_BUS to fix it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: a7e26f356c ("soc: imx: Add generic i.MX8 SoC driver")
Suggested-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
