Port the sh73a0 restart handling from the kzm9g-legacy board code to the
generic sh73a0 code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On sh73a0/kzm9g-legacy, probing of the i2c masters fails with:
i2c-sh_mobile i2c-sh_mobile.0: timing values out of range: L/H=0x208/0x1bf
sh_mobile: probe of i2c-sh_mobile.0 failed with error -22
According to the datasheet, the transfer rate is derived from the HP
clock (which runs at 104 MHz) divided by two. Hence
i2c_sh_mobile_platform_data.clks_per_count should be set to two.
Now probing succeeds, and i2c works:
i2c-sh_mobile i2c-sh_mobile.0: I2C adapter 0 with bus speed 100000 Hz (L/H=0x104/0xe0)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
For cloned bio, bio->bi_vcnt can't be used at all, and we
have resort to bio_segments() to figure out how many
segment there are in the bio.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Florian Fainelli says:
====================
net: bcmgenet: power management related fixes
These two patches fixes issues seen while testing power management on
platforms using the GENET driver.
First patch fixes an issue with the PHY state machine queuing work after
resume since we are not properly detached from it.
Second patch fixes an issue with GENET interfaces that were not properly
restored to a working state after a S3 suspend/resume cycle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case an interface has been brought down before entering S3, and then
brought up out of S3, all the initialization done during
bcmgenet_probe() by bcmgenet_mii_init() calling bcmgenet_mii_config() is
just lost since register contents are restored to their reset values.
Re-apply this configuration anytime we call bcmgenet_open() to make sure
our port multiplexer is properly configured to match the PHY interface.
Since we are now calling bcmgenet_mii_config() everytime bcmgenet_open()
is called, make sure we only print the message during initialization
time not to pollute the console.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_disconnect() is the only way to guarantee that we are not going to
schedule more work on the PHY state machine workqueue for that
particular PHY device.
This fixes an issue where a network interface was suspended prior to a
system suspend/resume cycle and would then be resumed as part of
mdio_bus_resume(), since the GENET interface clocks would have been
disabled, this basically resulted in bus errors to appear since we are
invoking the GENET driver adjust_link() callback.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell Berlin BG2 based Sony NSZ-GS7 has an unpopulated SATA plug
on its PCB solder side. As it is quite easy to populate and I have
done it, enable AHCI and SATA by default.
Acked-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Add DT nodes for the AHCI controller and SATA PHY found on Marvell
Berlin2 SoCs.
Acked-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch removes the dependency of the VENDOR entry and fixes
the QCA7000 one.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And use the more common mechanisms directly.
Other miscellanea:
o Coalesce formats
o Add missing newlines
o Realign arguments
o Remove unnecessary OOM message logging as
there's a generic stack dump already on OOM.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add BDW-H to the list of supported processors.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support of Hardware Managed Performance States (HWP) described in Volume 3
section 14.4 of the SDM.
With HWP enbaled intel_pstate will no longer be responsible for selecting P
states for the processor. intel_pstate will continue to register to
the cpufreq core as the scaling driver for CPUs implementing
HWP. In HWP mode intel_pstate provides three functions reporting
frequency to the cpufreq core, support for the set_policy() interface
from the core and maintaining the intel_pstate sysfs interface in
/sys/devices/system/cpu/intel_pstate. User preferences expressed via
the set_policy() interface or the sysfs interface are forwared to the
CPU via the HWP MSR interface.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support of Hardware Managed Performance States (HWP) described in Volume 3
section 14.4 of the SDM.
One bit CPUID.06H:EAX[bit 7] expresses the presence of the HWP feature on
the processor. The remaining bits CPUID.06H:EAX[bit 8-11] denote the
presense of various HWP features.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is possible that a GPE handler or a fixed event handler still accessed
after removing the handlers by invoking acpi_remove_gpe_handler() or
acpi_remove_fixed_event_handler(), this possibility can crash OPSM after a
module removal. In the Linux kernel, though all other GPE drivers are not
modules, since the IPMI_SI (ipmi_si_intf.c) can be compiled as a module, we
still need to consider a solution for this issue when the driver switches
to ACPI_GPE_RAW_HANDLER mode in order to invoke GPE APIs.
ACPICA expects acpi_os_wait_events_complete() to be invoked after GPE
disabling so that OSPM can ensure all running GPE handlers have exitted.
But currently acpi_os_wait_events_complete() can only flush _Lxx/_Exx
evaluation work queue and this philosophy cannot work for drivers that have
installed a dedicated GPE handler.
The only way to protect a callback is to perform some state holders
(reference count, state machine) before invoking the callback. Then this
issue can only be fixed by the following means:
1. Flush GPE in ACPICA before invoking the GPE handler. But currently,
there is no such implementation in acpi_ev_gpe_dispatch().
2. Flush GPE in ACPICA OSL before invoking the SCI handler. But currently,
there is no such implementation in acpi_irq().
3. Flush IRQ in OSPM IRQ layer before invoking the IRQ handler. In Linus
kernel, this can be done by synchronize_irq().
4. Flush scheduling in OSPM vector entry layer before invoking the vector.
In Linux, this can be done by synchronize_sched().
Since ACPICA expects the GPE handlers to be flushed by the ACPICA OSL or
the GPE drivers. If it is implemented by the GPE driver, we should see
synchronize_irq()/synchronize_sched() invoked in such drivers. If it is
implemented by the ACPICA OSL, ACPICA currently provides
acpi_os_wait_events_complete() hook to achieve this. After the following
commit:
Commit: 69c841b6dd
Author: Lv Zheng <lv.zheng@intel.com>
Subject: ACPICA: Update use of acpi_os_wait_events_complete interface.
The OSL acpi_os_wait_events_complete() is invoked after a GPE handler is
removed from acpi_remove_gpe_handler() or a fixed event handler is removed
from acpi_remove_fixed_event_handler(). Thus it is possible to implement
GPE handler flushing using this ACPICA OSL now. So the solution 1 is
currently not taken into account.
By examining the IPMI_SI driver, we noticed that the IPMI_SI driver:
1. Uses free_irq() to flush non GPE based IRQ handlers, in free_irq(),
synchronize_irq() is invoked, and
2. Uses acpi_remove_gpe_handler() to flush GPE based IRQ handlers, for such
IRQ handlers, there is no synchronize_irq() invoked.
Since there isn't synchronize_sched() implemented for this driver, from the
driver's perspective, acpi_remove_gpe_handler() should have properly
flushed the GPE handlers for it. Since the driver doesn't invoke
synchronize_irq(), the solution 3 is not what the drivers expect.
This patch implements solution 2. But since given the fact that the GPE is
managed inside of ACPICA, and implementing the GPE flushing requires to
implement the whole GPE management code again in the OSL, instead of
flushing GPE, this patch flushes IRQ in acpi_os_wait_events_complete(). The
flushing could last longer than expected as though the target GPE/fixed
event that is removed can be fastly flushed, other GPEs/fix events can still
be issued during the flushing period.
This patch fixes this issue by invoking synchronize_hardirq() in
acpi_os_wait_events_complete(). The reason why we don't invoke
synchronize_irq() is: currently ACPICA is not threaded IRQ capable and the
only difference between synchronize_irq() and synchronize_hardirq() is
synchronize_irq() also flushes threaded IRQ handlers. Thus using
synchronize_hardirq() can help to reduce the overall synchronization time
for the current ACPICA implementation.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: linux-acpi@vger.kernel.org
Cc: devel@acpica.org
Cc: openipmi-developer@lists.sourceforge.net
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In commit 46ba51e (ACPI / processor: Introduce ARCH_MIGHT_HAVE_ACPI_PDC),
acpi_processor_set_pdc() was moved to processor_pdc.c, so update
the comments accordingly.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On runtime PM aware platforms the DMA have to manage its own power state. This
patch enables runtime PM support and applies necessary calls wherever it's
needed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The LPSS DMA controller does not have _PS0 and _PS3 methods. Moreover it can be
powered off automatically whenever the last LPSS device goes down. In case of
no power any access to the DMA controller will hang the system. The behaviour
is reproduced on some HP laptops based on Intel Bay Trail [1] as well as on
Asus T100 transformer.
This patch introduces a so called 'proxy' device that has the knobs to handle a
power of the LPSS island. When the system needs to program the DMA controller
it calls to the ACPI LPSS power domain callbacks that wake or suspend the
'proxy' device.
[1] http://www.spinics.net/lists/dmaengine/msg01514.html
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The LPSS DMA controller would like to use the specific PM domain callbacks
during early stage, namely in ->probe(). This patch moves the specific PM
domain assignment early to be accessible during a whole life time of the device
in the system.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the LPSS devices are located in the different power domains depends
on LPSS_SAVE_CTX flag. We would like to use the specific power domain for all
LPSS devices.
The LPSS DMA controller has no knobs to control its power state. The specific
power domain implementation will handle this case. The patch does a preparation
for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
RAPL implementation on Atom has made some changes that are not compatible
with Core CPUs. Specifically, it is different in the way units are computed
as well as floor frequency is enforced.
This patch uses the per CPU model functions to handle the differences. Intel
Software Developers' Manual has also been updated to reflect the changes in
Table 35-7 V3C.
Signed-off-by: Ajay Thomas <ajay.thomas.david.rajamanickam@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
RAPL implementations may vary slightly between Core and Atom CPUs. There are
also potential differences among generations of CPUs within the family.
This patch adds a per model structure to abstract the differences such that
variations can be handled cleanly.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
First of all IRQCHIP_SKIP_SET_WAKE is not a valid irq_gc_flags and thus
should not be passed as the last argument of
irq_alloc_domain_generic_chips.
Then pass the correct handler (handle_fasteoi_irq) to
irq_alloc_domain_generic_chips instead of manually re-setting it in the
initialization loop.
And eventually initialize default irq flags to the pseudo standard:
IRQ_REQUEST | IRQ_PROBE | IRQ_AUTOEN.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Fixes: b1479ebb77 ("irqchip: atmel-aic: Add atmel AIC/AIC5 drivers")
Cc: <stable@vger.kernel.org> # v3.17+
Link: https://lkml.kernel.org/r/1415712816-9202-1-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In commit 3891a04aaf ("x86-64, espfix: Don't leak bits 31:16 of %esp
returning..") the "ESPFix Area" was added to the page table dump special
sections. That area, though, has a limited amount of entries printed.
The EFI runtime services are, unfortunately, located in-between the
espfix area and the high kernel memory mapping. Due to the enforced
limitation for the espfix area, the EFI mappings won't be printed in the
page table dump.
To make the ESP runtime service mappings visible again, provide them a
dedicated entry.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
This reverts commit 84be880560, which itself reverted my original
attempt to move x86 from #include'ing .c files from across the tree
to using the EFI stub built as a static library.
The issue that affected the original approach was that splitting
the implementation into several .o files resulted in the variable
'efi_early' becoming a global with external linkage, which under
-fPIC implies that references to it must go through the GOT. However,
dealing with this additional GOT entry turned out to be troublesome
on some EFI implementations. (GCC's visibility=hidden attribute is
supposed to lift this requirement, but it turned out not to work on
the 32-bit build.)
Instead, use a pure getter function to get a reference to efi_early.
This approach results in no additional GOT entries being generated,
so there is no need for any changes in the early GOT handling.
Tested-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
There is no need to keep the module loaded when it serves no function in
case the EFI runtime services are disabled. Return an error in this case
so loading the module will fail.
Also supply a module_exit function to allow unloading the module.
Last, but not least, set the owner of the file_system_type struct.
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
While developing MST support I noticed I often got the wrong data
back from a transaction, in a racy fashion. I noticed the scratch
space wasn't locked against concurrent users.
Based on a patch by Alex, but I've made it a bit more obvious when
things are locked.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
If i_size becomes large outside of MAX_INLINE_DATA, we shoud convert the inode.
Otherwise, we can make some dirty pages during the truncation, and those pages
will be written through f2fs_write_data_page.
At that moment, the inode has still inline_data, so that it tries to write non-
zero pages into inline_data area.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The scenario is like this.
One trhead triggers:
f2fs_write_data_pages
lock_page
f2fs_write_data_page
f2fs_lock_op <- wait
The other thread triggers:
f2fs_truncate
truncate_blocks
f2fs_lock_op
truncate_partial_data_page
lock_page <- wait for locking the page
This patch resolves this bug by relocating truncate_partial_data_page.
This function is just to truncate user data page and not related to FS
consistency as well.
And, we don't need to call truncate_inline_data. Rather than that,
f2fs_write_data_page will finally update inline_data later.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Now only s390/MSI use default_msi_mask_irq() and default_msix_mask_irq(),
replace them with the common MSI mask IRQ functions __msi_mask_irq() and
__msix_mask_irq(). Remove default_msi_mask_irq() and
default_msix_mask_irq().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
CC: linux-s390@vger.kernel.org
The problem fixed by 0e4ccb1505 ("PCI: Add x86_msi.msi_mask_irq() and
msix_mask_irq()") has been fixed in a simpler way by a previous commit
("PCI/MSI: Add pci_msi_ignore_mask to prevent writes to MSI/MSI-X Mask
Bits").
The msi_mask_irq() and msix_mask_irq() x86_msi_ops added by 0e4ccb1505
are no longer needed, so revert the commit.
default_msi_mask_irq() and default_msix_mask_irq() were added by
0e4ccb1505 and are still used by s390, so keep them for now.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: xen-devel@lists.xenproject.org
When the user space tries to set scaling_(max|min)_freq through
sysfs, the cpufreq_set_policy() asks other driver's opinions
for the max/min frequencies. Some device drivers, like Tegra
CPU EDP which is not upstreamed yet though, may constrain the
CPU maximum frequency dynamically because of board design.
So if the user space access happens and some driver is capping
the cpu frequency at the same time, the user_policy->(max|min)
is overridden by the capped value, and that's not expected by
the user space. And if the user space is not invoked again,
the CPU will always be capped by the user_policy->(max|min)
even no drivers limit the CPU frequency any more.
This patch preserves the user specified min/max settings, so that
every time the cpufreq policy is updated, the new max/min can
be re-evaluated correctly based on the user's expection and
the present device drivers' status.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Status variable is never initialized, can carry an arbitrary value
on the stack and thus may let the function fail.
Fixes: e90dd26456 ("ixgbe: Make return values more direct")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While preparing an ad-hoc start command, the capability info bitmap is
needlessly set from the command, and then the ESS bit cleared.
Change to set the bitmap directly without reference to the command.
Signed-off-by: James Cameron <quozl@laptop.org>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wlcore_cmd_send_failsafe() function is only called in the cmd.c
file, where it is definde. Make it static.
Additionally, move the EXPORT_SYMBOL macro for wl1271_cmd_send() to
the right place.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for the minimum required buffer length in wlcore_cmd_send() and
wlcore_cmd_configure_failsafe. This ensures that we will never try to
use a buffer that is smaller than the required header.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's been observed that wrong firmware version (ex. 66.14.96.p9
instead of 14.66.9.p96) is displayed on big endian platforms.
The problem is fixed here.
Reported-by: Daniel Mosquera <daniel.mosquera@ctag.com>
Tested-by: Daniel Mosquera <daniel.mosquera@ctag.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use code provided by Ashish Patro <patro@cs.wisc.edu>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use values provided by Ashish Patro <patro@cs.wisc.edu>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some reason it didn't coused obvious problems.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
not sure why.
Initially provided by Ashish Patro <patro@cs.wisc.edu>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename exports from ath9k_spectral_* to ath9k_cmn_spectral_*
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now we should be ready to make this code common.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
last preparation before moving ath9k_spectral_scan_ to spectral.c
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
