The floating point registers of a process that uses vector instruction are
not store into task->thread.fp_regs anymore but in the upper halves of the
first 16 vector registers.
The ptrace interface for the peeks and pokes to the user area fails to take
this into account. Fix __peek_user[_compat] and __poke_user[_compat]
to use the vector array for the floating pointer register if the process
has one.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Explicitly set the dr_mode for the dwc3 controller on the
Snow board to host mode. This is required to ensure the
controller is initialized in the right mode if the kernel is
build with USB gadget support.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
nvram_pstore_info's buf_lock is not initialized before registering,
which is clearly incorrect.
It causes some strange behavior when trying to obtain the lock during
kdump process.
On a UP configuration, the console stopped for a couple of seconds, then
"lockup suspected" warning printed out, but then it continued to run.
So try lock fails, and lockup reported, but then arch_spin_lock()
passes.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
[mpe: Edited changelog]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function probe counting for traceon and traceoff suffered a race
condition where if the probe was executing on two or more CPUs at the
same time, it could decrement the counter by more than one when
disabling (or enabling) the tracer only once.
The way the traceon and traceoff probes are suppose to work is that
they disable (or enable) tracing once per count. If a user were to
echo 'schedule:traceoff:3' into set_ftrace_filter, then when the
schedule function was called, it would disable tracing. But the count
should only be decremented once (to 2). Then if the user enabled tracing
again (via tracing_on file), the next call to schedule would disable
tracing again and the count would be decremented to 1.
But if multiple CPUS called schedule at the same time, it is possible
that the count would be decremented more than once because of the
simple "count--" used.
By reading the count into a local variable and using memory barriers
we can guarantee that the count would only be decremented once per
disable (or enable).
The stack trace probe had a similar race, but here the stack trace will
decrement for each time it is called. But this had the read-modify-
write race, where it could stack trace more than the number of times
that was specified. This case we use a cmpxchg to stack trace only the
number of times specified.
The dump probes can still use the old "update_count()" function as
they only run once, and that is controlled by the dump logic
itself.
Link: http://lkml.kernel.org/r/20141118134643.4b550ee4@gandalf.local.home
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The locked page should be released before returning the function.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The LEDs on the kzm9g board are labeled using upper-case characters.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The LEDs on the koelsch board are labeled using upper-case characters.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The IIC nodes used the generic compatible properties only.
This causes the driver to fail when using Standard Speed, as the
operational clock is driven by the 104 MHz HP clock:
i2c-sh_mobile e6820000.i2c: timing values out of range: L/H=0x208/0x1bf
i2c-sh_mobile: probe of e6820000.i2c failed with error -22
Add the SoC-specific compatible property to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The IIC nodes used the generic compatible properties only.
This may cause the driver to fail when using Standard Speed on IIC
masters where the operational clock is driven by the 130 MHz HP clock.
Add the SoC-specific compatible property to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Koelsch I2C2 has 400kHz settings,
but, ak4643 audio codec chip which is connected to I2C2 can't
work such frequency.
Fixup I2C2 clock frequency to 100kHz.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Lager IIC2 is using default clock frequency,
but, ak4643 audio codec chip needs 100kHz
This patch clarifies IIC2 clock frequency as 100kHz.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The number of and dependencies between high-level power management
Kconfig options make life much harder than necessary. Several
conbinations of them have to be tested and supported, even though
some of those combinations are very rarely used in practice (if
they are used in practice at all). Moreover, the fact that we
have separate independent Kconfig options for runtime PM and
system suspend is a serious obstacle for integration between
the two frameworks.
To overcome these difficulties, always select PM_RUNTIME if PM_SLEEP
is set. Among other things, this will allow system suspend callbacks
provided by bus types and device drivers to rely on the runtime PM
framework regardless of the kernel configuration.
Enthusiastically-acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The commit 5935839ad7
"mac80211: improve minstrel_ht rate sorting by throughput & probability"
introduced a crash on rate sorting that occurs when the rate added to
the sorting array is faster than all the previous rates. Due to an
off-by-one error, it reads the rate index from tp_list[-1], which
contains uninitialized stack garbage, and then uses the resulting index
for accessing the group rate stats, leading to a crash if the garbage
value is big enough.
Cc: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Report is received in "buffer"; fix the following i2c_hid_dbg()
to dump data from the correct pointer.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
[Antonio Borneo: cleanup and rebase to v3.17]
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Suggested-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bosch M_CAN is CAN FD capable device. This patch implements the CAN
FD features include up to 64 bytes payload and bitrate switch function.
1) Change the Rx FIFO and Tx Buffer to 64 bytes for support CAN FD
up to 64 bytes payload. It's backward compatible with old 8 bytes
normal CAN frame.
2) Allocate can frame or canfd frame based on EDL bit
3) Bitrate Switch function is disabled by default and will be enabled
according to CANFD_BRS bit in cf->flags.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The spec mentions there may be a delay until the value written to INIT can be
read back due to the synchronization mechanism between the two clock domains.
But it does not indicate the exact clock cycles needed. The 5us delay is a
test value and seems ok.
Without the delay, CCCR.CCE bit may fail to be set and then the initialization
fail sometimes when do repeatly up and down.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The original code missed to set the cf->can_dlc in the RTR case, so add it.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The M_CAN message RAM is usually equipped with a parity or ECC functionality.
But RAM cells suffer a hardware reset and can therefore hold arbitrary content
at startup - including parity and/or ECC bits.
To prevent the M_CAN controller detecting checksum errors when reading
potentially uninitialized TX message RAM content to transmit CAN frames the TX
message RAM has to be written with (any kind of) initial data.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can uses io memory which makes it not compilable on architectures
without HAS_IOMEM such as UML:
drivers/built-in.o: In function `m_can_plat_probe':
m_can.c:(.text+0x218cc5): undefined reference to `devm_ioremap_resource'
m_can.c:(.text+0x218df9): undefined reference to `devm_ioremap'
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If icmp_rcv() has successfully processed the incoming ICMP datagram, we
should use consume_skb() rather than kfree_skb() because a hit on the likes
of perf -e skb:kfree_skb is not called-for.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
