Add two new entries to the Broadcom BCM7xxx internal PHY driver for
BCM7250 and BCM7364 chips. Those chips share the usual 28nm process
Gigabit PHY sequence and require the same workarounds so far.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom started to use a new OUI for its 2013 and newer products:
D4-01-29 which translates into 0xae025000 for a 32-bits OUI, add its
definition.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY_BCM_OUI_4 is missing two significant digits that actually make it an
OUI, add those missing bits so it becomes usable again for matching.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case switch port tagging is disabled (voluntarily, or the switch just
does not support it), allow us to continue using the defined set of
dsa_device_ops in net/dsa/slave.c.
We introduce dsa_protocol_is_tagged() to check whether we need to
override skb->protocol and go through the DSA-specifif packet_type
function, or if we just go on and receive the SKB through the normal
path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for updating the DSA code and avoid using ifdefs there,
provide an empty stub for fixed_phy_set_link_update when
CONFIG_FIXED_PHY is not selected.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA is currently registering one packet_type function per EtherType it
needs to intercept in the receive path of a DSA-enabled Ethernet device.
Right now we have three of them: trailer, DSA and eDSA, and there might
be more in the future, this will not scale to the addition of new
protocols.
This patch proceeds with adding a new layer of abstraction and two new
functions:
dsa_switch_rcv() which will dispatch into the tag-protocol specific
receive function implemented by net/dsa/tag_*.c
dsa_slave_xmit() which will dispatch into the tag-protocol specific
transmit function implemented by net/dsa/tag_*.c
When we do create the per-port slave network devices, we iterate over
the switch protocol to assign the DSA-specific receive and transmit
operations.
A new fake ethertype value is used: ETH_P_XDSA to illustrate the fact
that this is no longer going to look like ETH_P_DSA or ETH_P_TRAILER
like it used to be.
This allows us to greatly simplify the check in eth_type_trans() and
always override the skb->protocol with ETH_P_XDSA for Ethernet switches
tagged protocol, while also reducing the number repetitive slave
netdevice_ops assignments.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support read-only memory regions on arm and arm64, we have a need to
resolve a gfn to an hva given a pointer to a memslot to avoid looping
through the memslots twice and to reuse the hva error checking of
gfn_to_hva_prot(), add a new gfn_to_hva_memslot_prot() function and
refactor gfn_to_hva_prot() to use this function.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Add the helpers to be used by modules wishing to expose unsafe debugging
or testing module parameters that taint the kernel when set.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Jon Mason <jon.mason@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add flags field to struct kernel_params, and add the first flag: unsafe
parameter. Modifying a kernel parameter with the unsafe flag set, either
via the kernel command line or sysfs, will issue a warning and taint the
kernel.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Jon Mason <jon.mason@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Make it clear this is about kernel_param_ops, not kernel_param (which
will soon have a flags field of its own). No functional changes.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Jon Mason <jon.mason@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is a patch for supporting device tree of DA9211/DA9213.
Signed-off-by: James Ban <james.ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert all uses of __get_cpu_var for address calculation to use
this_cpu_ptr instead.
[Uses of __get_cpu_var with cpumask_var_t are no longer
handled by this patch]
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
TPC report element is contained in spectrum management's tpc report
action frames and in radio measurement's link measurement report
action frames. Add a function which checks whether an action frame
contains this element. This may be needed by the drivers in order
to set the correct tx power value in these frames.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Corrected a minor typo in a code comment where 'be' was missing.
Signed-off-by: Raymond L. Rivera <ray.l.rivera@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Provide an implementation for dma_{alloc,free,mmap}_writecombine() when
the architecture supports DMA attributes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
As reported by Jesper Dangaard Brouer, for high packet rates the
overhead of having another indirect call in the TX path is
non-trivial.
There is the indirect call itself, and then there is all of the
reloading of the state to refetch the tail pointer value and
then write the device register.
Move to a more passive scheme, which requires very light modifications
to the device drivers.
The signal is a new skb->xmit_more value, if it is non-zero it means
that more SKBs are pending to be transmitted on the same queue as the
current SKB. And therefore, the driver may elide the tail pointer
update.
Right now skb->xmit_more is always zero.
Signed-off-by: David S. Miller <davem@davemloft.net>
For v3.12 and prior, 1-bit Hamming code ECC via software was the
default choice. Commit c66d039197 in v3.13 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.12
and prior to be unusable in v3.13 and later. So revert back to
using software ECC by default if an ECC scheme is not explicitely
specified.
This defect can be observed on the following boards during legacy boot
-omap3beagle
-omap3touchbook
-overo
-am3517crane
-devkit8000
-ldp
-3430sdp
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use is_kdump_kernel() to detect kdump kernel, instead of reset_devices.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights:
- More fixes for read/write codepath regressions
- Sleeping while holding the inode lock
- Stricter enforcement of page contiguity when coalescing requests
- Fix up error handling in the page coalescing code
- Don't busy wait on SIGKILL in the file locking code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT+0LpAAoJEGcL54qWCgDyWfsP/imrpge47aZywi95chV8vgjM
O85ITZbupTFwXbB7kE63CrcaxRGhFrSStk4UDhDCDkHfFb1ksjZaPR1mnkwvkR2p
4+JUoq0fkPfeX21+rqKCYmnhstpne/N8K8FJBsEs3/TqiCBWxWOelLXdyWun4H5B
9JBYQ7FYitUazeSiSiDXcl7Di/E09cFPi0H5VPKRyuNdYxySabnsBOELBE/28iXr
egW1I9UKQR2EtBrvgazBbWE5XmB9XAm4X3sD1l0QD65mfSNkbnNhPFSiCdT7f/d6
9uxECR0Y4wNYgYAfVLBew5/MXJajcv03BFMKmTUeGj9fOQzycpBT4Dx2KxEWqfnt
Xk2nNbISxBnO0koMflmo+LPv2lv+Br3kQ+eZCHHKknvBrX2a6bJdTCZkwACVtND9
LdbAveFQpdaeLrm/28TnRoE927r+VeAVM19yOSG8sNAskFFg4Yy51tR0e1GivkJT
+qmmTRx+l78HjHvoPXOYdNgBC954r6APH5ST7su/7WxNClM36fEK6XxA9xbDLJWm
wUzlGKvpwEeBJJhgjbQLwuU8BiksjFz/CaiObNvPOpc/d2GoKIhnTg19kNhg2R//
UCDa2d5fep4z0Bo9p0s1KZm9pSBkkLjvRp9dm8WEIxLcdaF1jBK3dJECepm6ccvw
dmEmEfjbMudVdt/ZhapJ
=2wRt
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.17-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client fixes from Trond Myklebust:
"Highlights:
- more fixes for read/write codepath regressions
* sleeping while holding the inode lock
* stricter enforcement of page contiguity when coalescing requests
* fix up error handling in the page coalescing code
- don't busy wait on SIGKILL in the file locking code"
* tag 'nfs-for-3.17-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: Don't busy-wait on SIGKILL in __nfs_iocounter_wait
nfs: can_coalesce_requests must enforce contiguity
nfs: disallow duplicate pages in pgio page vectors
nfs: don't sleep with inode lock in lock_and_join_requests
nfs: fix error handling in lock_and_join_requests
nfs: use blocking page_group_lock in add_request
nfs: fix nonblocking calls to nfs_page_group_lock
nfs: change nfs_page_group_lock argument
separate trampolines had a design flaw with the interaction between
the function and function_graph tracers.
The main flaw was the simplification of the use of multiple tracers having
the same filter (like function and function_graph, that use the
set_ftrace_filter file to filter their code). The design assumed that the
two tracers could never run simultaneously as only one tracer can be
used at a time. The problem with this assumption was that the function
profiler could be implemented on top of the function graph tracer, and
the function profiler could run at the same time as the function tracer.
This caused the assumption to be broken and when ftrace detected this
failed assumpiton it would spit out a nasty warning and shut itself down.
Instead of using a single ftrace_ops that switches between the function
and function_graph callbacks, the two tracers can again use their own
ftrace_ops. But instead of having a complex hierarchy of ftrace_ops,
the filter fields are placed in its own structure and the ftrace_ops
can carefully use the same filter. This change took a bit to be able
to allow for this and currently only the global_ops can share the same
filter, but this new design can easily be modified to allow for any
ftrace_ops to share its filter with another ftrace_ops.
The first four patches deal with the change of allowing the ftrace_ops
to share the filter (and this needs to go to 3.16 as well).
The fifth patch fixes a bug that was also caused by the new changes
but only for archs other than x86, and only if those archs implement
a direct call to the function_graph tracer which they do not do yet
but will in the future. It does not need to go to stable, but needs
to be fixed before the other archs update their code to allow direct
calls to the function_graph trampoline.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT+hqSAAoJEKQekfcNnQGulvcH/0O4NMXX4HH1dQlYgKEaSYxE
Nh8WdiewopF5iaeNvo+8Nzdq8D2k3KgMOqSlzJ4JVmzd7gjOBSGeKDfqFwR+IbTk
9LcaJJCI3oG3MEf6m7gZMdjKPKyxkeYHDtG7kRHo8z94eliV9pKC6fUnEWayQO3o
Kv6IBupdkF8ICAiKRae5Uo0c9wjZ9YP0bZS7fxI2hJw3h/NMFnhnhUL03URIx8e3
dqgpweYg+P3KPfp2Jz6safdJqLTPK9rqqhkZhylbDl7o78xEzRN7wCyB6Nak00xz
swRgsW6vFP7ci/YSNx+B6HCIf7NTm3WLDrrIhitNHcJUZwUMU3CRO9IJHGsTuEE=
=J5lZ
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull fix for ftrace function tracer/profiler conflict from Steven Rostedt:
"The rewrite of the ftrace code that makes it possible to allow for
separate trampolines had a design flaw with the interaction between
the function and function_graph tracers.
The main flaw was the simplification of the use of multiple tracers
having the same filter (like function and function_graph, that use the
set_ftrace_filter file to filter their code). The design assumed that
the two tracers could never run simultaneously as only one tracer can
be used at a time. The problem with this assumption was that the
function profiler could be implemented on top of the function graph
tracer, and the function profiler could run at the same time as the
function tracer. This caused the assumption to be broken and when
ftrace detected this failed assumpiton it would spit out a nasty
warning and shut itself down.
Instead of using a single ftrace_ops that switches between the
function and function_graph callbacks, the two tracers can again use
their own ftrace_ops. But instead of having a complex hierarchy of
ftrace_ops, the filter fields are placed in its own structure and the
ftrace_ops can carefully use the same filter. This change took a bit
to be able to allow for this and currently only the global_ops can
share the same filter, but this new design can easily be modified to
allow for any ftrace_ops to share its filter with another ftrace_ops.
The first four patches deal with the change of allowing the ftrace_ops
to share the filter (and this needs to go to 3.16 as well).
The fifth patch fixes a bug that was also caused by the new changes
but only for archs other than x86, and only if those archs implement a
direct call to the function_graph tracer which they do not do yet but
will in the future. It does not need to go to stable, but needs to be
fixed before the other archs update their code to allow direct calls
to the function_graph trampoline"
* tag 'trace-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Use current addr when converting to nop in __ftrace_replace_code()
ftrace: Fix function_profiler and function tracer together
ftrace: Fix up trampoline accounting with looping on hash ops
ftrace: Update all ftrace_ops for a ftrace_hash_ops update
ftrace: Allow ftrace_ops to use the hashes from other ops
Instead of a void function, return the trigger pointer.
Whilst not in of itself a fix, this makes the following set of
7 fixes cleaner than they would otherwise be.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
This function will help an async task processing batched jobs from
workqueue decide if it wants to keep processing on more chunks of batched
work that can be delayed, or to accumulate more work for more efficient
batched processing later.
If no other tasks are running on the cpu, the batching process can take
advantgae of the available cpu cycles to a make decision to continue
processing the existing accumulated work to minimize delay,
otherwise it will yield.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use HAVE_JUMP_LABEL as elsewhere in the kernel to ensure
that the toolchain has the required support in addition to
CONFIG_JUMP_LABEL being set.
Signed-off-by: Zhouyi Zhou <yizhouzhou@ict.ac.cn>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch addresses a couple of minor items, mostly addesssing
prandom_bytes(): 1) prandom_bytes{,_state}() should use size_t
for length arguments, 2) We can use put_unaligned() when filling
the array instead of open coding it [ perhaps some archs will
further benefit from their own arch specific implementation when
GCC cannot make up for it ], 3) Fix a typo, 4) Better use unsigned
int as type for getting the arch seed, 5) Make use of
prandom_u32_max() for timer slack.
Regarding the change to put_unaligned(), callers of prandom_bytes()
which internally invoke prandom_bytes_state(), don't bother as
they expect the array to be filled randomly and don't have any
control of the internal state what-so-ever (that's also why we
have periodic reseeding there, etc), so they really don't care.
Now for the direct callers of prandom_bytes_state(), which
are solely located in test cases for MTD devices, that is,
drivers/mtd/tests/{oobtest.c,pagetest.c,subpagetest.c}:
These tests basically fill a test write-vector through
prandom_bytes_state() with an a-priori defined seed each time
and write that to a MTD device. Later on, they set up a read-vector
and read back that blocks from the device. So in the verification
phase, the write-vector is being re-setup [ so same seed and
prandom_bytes_state() called ], and then memcmp()'ed against the
read-vector to check if the data is the same.
Akinobu, Lothar and I also tested this patch and it runs through
the 3 relevant MTD test cases w/o any errors on the nandsim device
(simulator for MTD devs) for x86_64, ppc64, ARM (i.MX28, i.MX53
and i.MX6):
# modprobe nandsim first_id_byte=0x20 second_id_byte=0xac \
third_id_byte=0x00 fourth_id_byte=0x15
# modprobe mtd_oobtest dev=0
# modprobe mtd_pagetest dev=0
# modprobe mtd_subpagetest dev=0
We also don't have any users depending directly on a particular
result of the PRNG (except the PRNG self-test itself), and that's
just fine as it e.g. allowed us easily to do things like upgrading
from taus88 to taus113.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add skb_gro_checksum_validate, skb_gro_checksum_validate_zero_check,
and skb_gro_checksum_simple_validate, and __skb_gro_checksum_complete.
These are the cognates of the normal checksum functions but are used
in the gro_receive path and operate on GRO related fields in sk_buffs.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- A largeish fix for the IRQ handling in the new Zynq driver.
The quite verbose commit message gives the exact details.
- Move some defines for gpiod flags outside an ifdef to make
stub functions work again.
- Various minor fixes that we can accept for -rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7iYA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
- a largeish fix for the IRQ handling in the new Zynq driver. The
quite verbose commit message gives the exact details.
- move some defines for gpiod flags outside an ifdef to make stub
functions work again.
- various minor fixes that we can accept for -rc1.
* tag 'gpio-v3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio-lynxpoint: enable input sensing in resume
gpio: move GPIOD flags outside #ifdef
gpio: delete unneeded test before of_node_put
gpio: zynq: Fix IRQ handlers
gpiolib: devres: use correct structure type name in sizeof
MAINTAINERS: Change maintainer for gpio-bcm-kona.c
Dan Carpenter reported that the static checker emits the warning
net/netfilter/ipset/ip_set_list_set.c:600 init_list_set()
warn: integer overflows 'sizeof(*map) + size * set->dsize'
Limit the maximal number of elements in list type of sets.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Adding new perf event state to indicate that the monitored task has
exited. In this case the event stays alive until the owner task exits
or close the event fd while providing the last data through the read
syscall and ring buffer.
Instead it needs to propagate the error info (monitored task has died)
via poll and read syscalls by returning POLLHUP and 0 respectively.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140811120102.GY9918@twins.programming.kicks-ass.net
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jean Pihet <jean.pihet@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-t5y3w8jjx6tfo5w8y6oajsjq@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Drivers, and perhaps other entities we have not yet considered,
sometimes want to know how deep the protocol headers go before
deciding how large of an SKB to allocate and how much of the packet to
place into the linear SKB area.
For example, consider a driver which has a device which DMAs into
pools of pages and then tells the driver where the data went in the
DMA descriptor(s). The driver can then build an SKB and reference
most of the data via SKB fragments (which are page/offset/length
triplets).
However at least some of the front of the packet should be placed into
the linear SKB area, which comes before the fragments, so that packet
processing can get at the headers efficiently. The first thing each
protocol layer is going to do is a "pskb_may_pull()" so we might as
well aggregate as much of this as possible while we're building the
SKB in the driver.
Part of supporting this is that we don't have an SKB yet, so we want
to be able to let the flow dissector operate on a raw buffer in order
to compute the offset of the end of the headers.
So now we have a __skb_flow_dissect() which takes an explicit data
pointer and length.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 28nm Gigabit PHY on BCM7xxx chips comes out of reset with absolutely
no EEE capabilities, such that we would actually return that we do not
support EEE when accessing 3.20 (MDIO_PCS_EEE_ABLE) registers.
Poke through the vendor-specific C45 register to enable EEE globally at
the PHY level, and advertise supported EEE modes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY drivers might need to access Clause 45 registers in Clause 22
compatibility mode to e.g: properly advertise EEE support when disabled
by default.
Export these two helper functions: phy_read_mmd_indirect() and
phy_write_mmd_indirect() for drivers to use them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shadow register 0x1C is used both by the BCM54xxx PHYs and the
BCM7xxx internal PHYs, move the accessors to a common location so both
drivers can use them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 439d39a9ac ("net: phy: broadcom:
extract register definitions") added a bunch of registers to brcmphy.h
but left some to broadcom.c, move all of them to the header file since
the BCM54xx and BCM7xxx PHY drivers do share all of these registers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ flags can be obtained from resource structure, there are no need
to use additional field in the platform_data to store these values.
This patch removes this field and convert existing users of this driver
to use IRQ flags from the resources.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Tejun Heo <tj@kernel.org>
Upon timeout, undo (via both timestamps/Eifel and DSACKs) was
disabled if any retransmits were still in flight. The concern was
perhaps that spurious retransmission sent in a previous recovery
episode may trigger DSACKs to falsely undo the current recovery.
However, this inadvertently misses undo opportunities (using either
TCP timestamps or DSACKs) when timeout occurs during a loss episode,
i.e. recurring timeouts or timeout during fast recovery. In these
cases some retransmissions will be in flight but we should allow
undo. Furthermore, we should only reset undo_marker and undo_retrans
upon timeout if we are starting a new recovery episode. Finally,
when we do reset our undo state, we now do so in a manner similar
to tcp_enter_recovery(), so that we require a DSACK for each of
the outstsanding retransmissions. This will achieve the original
goal by requiring that we receive the same number of DSACKs as
retransmissions.
This patch increases the undo events by 50% on Google servers.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This handles the 'nonblock=false' case in nfs_lock_and_join_requests.
If the group is already locked and blocking is allowed, drop the inode lock
and wait for the group lock to be cleared before trying it all again.
This should fix warnings found in peterz's tree (sched/wait branch), where
might_sleep() checks are added to wait.[ch].
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Pull networking fixes from David Miller:
"Here are some bug fixes that have piled up during ksummit/linuxcon.
1) Fix endian problems in ibmveth, from Anton Blanchard.
2) IPV6 routing code does GFP_KERNEL allocation in atomic, fix from
Benjamin Block.
3) SCTP association fixes from Daniel Borkmann.
4) When multiple VLAN headers are present we have to make sure the
second and subsequent ones are pullable in the SKB otherwise we
blindly dereference garbage. From Jiri Benc.
5) The argument adjustment of the signature of hlist_add_after*()
introduced a regression in the batman-adv code, fix from Sven
Eckelmann.
6) Fix TX hang handling to avoid a panic in i40e, from Anjali Singhai
Jain.
7) PTP flag test is inverted in i40e driver, from Jesse Brandeburg.
8) ATM LEC driver needs to hold RTNL mutex over MTU changes, from
Chas Williams.
9) Truncate packets larger then the TPACKET_V3 format configured
buffers, otherwise we overwrite past the end of said buffers.
From Eric Dumazet.
10) Fix endianness bugs in qlcnic firmware handling, from Rajesh
Borundia and Shahed Shaikh.
11) CXGB4 sometimes doesn't get all of the TX completion events it
should resulting in SKBs getting stuck in the TX queue, from
Hariprasad Shenai.
12) When the FEC chip's PTP clock is disabled, you can't access the
register. Add necessary checks to avoid the resulting hang, from
Fugang Duan"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
drivers: isdn: eicon: xdi_msg.h: Fix typo in #ifndef
net: sctp: fix suboptimal edge-case on non-active active/retrans path selection
net: sctp: spare unnecessary comparison in sctp_trans_elect_best
net: ethernet: broadcom: bnx2x: Remove redundant #ifdef
ibmveth: Fix endian issues with rx_no_buffer statistic
net: xgene: fix possible NULL dereference in xgene_enet_free_desc_rings()
openvswitch: fix panic with multiple vlan headers
net: ipv6: fib: don't sleep inside atomic lock
net: fec: ptp: avoid register access when ipg clock is disabled
cxgb4: Free completed tx skbs promptly
cxgb4: Fix race condition in cleanup
sctp: not send SCTP_PEER_ADDR_CHANGE notifications with failed probe
bnx2x: Revert UNDI flushing mechanism
qlcnic: Fix endianess issue in firmware load from file operation
qlcnic: Fix endianess issue in FW dump template header
qlcnic: Fix flash access interface to application
MAINTAINERS: Add section for MRF24J40 IEEE 802.15.4 radio driver
macvlan: Allow setting multicast filter on all macvlan types
packet: handle too big packets for PACKET_V3
MAINTAINERS: add entry for ec_bhf driver
...
This patch introduces DEF_NIDS_PER_INODE/GET_ORPHAN_BLOCKS/F2FS_CP_PACKS macro
instead of numbers in code for readability.
change log from v1:
o fix typo pointed out by Jaegeuk Kim.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Userspace needs to be notified if one changes some option.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the top level debug file system function tracer shares its
ftrace_ops with the function graph tracer. This was thought to be fine
because the tracers are not used together, as one can only enable
function or function_graph tracer in the current_tracer file.
But that assumption proved to be incorrect. The function profiler
can use the function graph tracer when function tracing is enabled.
Since all function graph users uses the function tracing ftrace_ops
this causes a conflict and when a user enables both function profiling
as well as the function tracer it will crash ftrace and disable it.
The quick solution so far is to move them as separate ftrace_ops like
it was earlier. The problem though is to synchronize the functions that
are traced because both function and function_graph tracer are limited
by the selections made in the set_ftrace_filter and set_ftrace_notrace
files.
To handle this, a new structure is made called ftrace_ops_hash. This
structure will now hold the filter_hash and notrace_hash, and the
ftrace_ops will point to this structure. That will allow two ftrace_ops
to share the same hashes.
Since most ftrace_ops do not share the hashes, and to keep allocation
simple, the ftrace_ops structure will include both a pointer to the
ftrace_ops_hash called func_hash, as well as the structure itself,
called local_hash. When the ops are registered, the func_hash pointer
will be initialized to point to the local_hash within the ftrace_ops
structure. Some of the ftrace internal ftrace_ops will be initialized
statically. This will allow for the function and function_graph tracer
to have separate ops but still share the same hash tables that determine
what functions they trace.
Cc: stable@vger.kernel.org # 3.16 (apply after 3.17-rc4 is out)
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Document the requirement that the request be dequeued and its
completion routine called before usb_ep_dequeue() returns. Also
fix some capitalization issues in the existing text.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Theoretically, our total inodes number is the same as total node number, but
there are three node ids are reserved in f2fs, they are 0, 1 (node nid), and 2
(meta nid), and they should never be used by user, so our total/free inode
number calculated in ->statfs is wrong.
This patch indroduces F2FS_RESERVED_NODE_NUM and then fixes this issue by
recalculating total/free inode number with the macro.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Introduce preempt notifiers for architecture specific code.
Advantage over creating a new notifier in every arch is slightly simpler
code and guaranteed call order with respect to kvm_sched_in.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
