The hardware manual says that software should attempt a new dynamic
config access (be it a a write or a read-back) only while the VALID bit
is cleared. The VALID bit is set by software to 1, and it remains set as
long as the hardware is still processing the request.
Currently the driver only polls for the command completion only for
reads, because that's when we need the actual data read back. Writes
have been more or less "asynchronous", although this has never been an
observable issue.
This change makes sja1105_dynamic_config_write poll the VALID bit as
well, to absolutely ensure that a follow-up access to the static config
finds the VALID bit cleared.
So VALID means "work in progress", while VALIDENT means "entry being
read is valid". On reads we check the VALIDENT bit too, while on writes
that bit is not always defined. So we need to factor it out of the loop,
and make the loop provide back the unpacked command structure, so that
sja1105_dynamic_config_read can check the VALIDENT bit.
The change also attempts to convert the open-coded loop to use the
read_poll_timeout macro, since I know this will come up during review.
It's more code, but hey, it uses read_poll_timeout!
Tested on SJA1105T, SJA1105S, SJA1110A.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows explicitly specifying which children are present on the mdio
bus. Additionally, it allows for non-phy MDIO devices on the bus.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an optional mdio bus child node. If present, the mac will
look for PHYs there instead of directly under the top-level node. This
eliminates any ambiguity about whether child nodes are PHYs, and allows
the MDIO bus to contain non-PHY devices.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 16nm internal EPHY that is present in 7712 is actually a 16nm
Gigabit PHY which has been forced to operate in 10/100 mode. Its
controls are therefore via the EXT_GPHY_CTRL registers and not via the
EXT_EPHY_CTRL which are used for all GENETv5 adapters. Add a match on
the 7712 compatible string to allow that differentiation to happen.
On previous GENETv4 chips the EXT_CFG_IDDQ_GLOBAL_PWR bit was cleared by
default, but this is not the case with this chip, so we need to make
sure we clear it to power on the EPHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7712 includes a GENETv5 adapter with an on-chip 10/100 16nm Ethernet PHY
which requires us to document that controller's integration specifically
for proper driver keying.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
7712 is a 16nm process SoC with a 10/100 integrated Ethernet PHY,
utilize the recently defined 16nm EPHY macro to configure that PHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts users of mdiobus to mdiodev using the following semantic
patch:
@@
identifier mdiodev;
expression regnum;
@@
- mdiobus_read(mdiodev->bus, mdiodev->addr, regnum)
+ mdiodev_read(mdiodev, regnum)
@@
identifier mdiodev;
expression regnum, val;
@@
- mdiobus_write(mdiodev->bus, mdiodev->addr, regnum, val)
+ mdiodev_write(mdiodev, regnum, val)
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This refactors the phylink pcs helper functions to use mdiobus_* instead
of mdiodev_*.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds some helpers for accessing non-phy MDIO devices. They are
analogous to phy_(read|write|modify), except that they take an mdio_device
and not a phy_device.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma failure was reported in the raspberry pi github (issue #4117).
https://github.com/raspberrypi/linux/issues/4117
The use of dma_set_mask_and_coherent fixes the issue.
Tested on 32/64-bit raspberry pi CM4 and 64-bit ubuntu x86 PC with EVB-LAN7430.
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs to clean up and return when the initialization fails on resume.
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With current KPU profile, we have 2 reserved entries which can
be loaded from firmware to parse custom headers. Adding changes
to increase these reserved entries to 6.
And also removed KPU entries for unused LTYPEs like
NPC_LT_LA_IH_8_ETHER, NPC_LT_LA_IH_4_ETHER, NPC_LT_LA_IH_2_ETHER
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a Mutex instead of a binary Semaphore for the purpose of enforcing
mutual exclusive access to the "pwrctrl_priv" structure.
Mutexes are sleeping locks similar to Semaphores with a 'count' of one
(like binary Semaphores), however they have a simpler interface, more
efficient performance, and additional constraints.
There is no change in the logic of the new code; however it is more
simple because it gets rid of four unnecessary wrappers:
_init_pwrlock(), _enter_pwrlock(),_exit_pwrlock(), _rtw_down_sema().
Actually, there is a change in the state in which the code waits for
acquiring locks, because it makes it in an uninterruptible state
(instead the old code used down_interruptibe()). Interruptible
waits are neither required nor wanted in this driver.
Tested with ASUSTek Computer, Inc. Realtek 8188EUS [USB-N10 Nano].
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Link: https://lore.kernel.org/r/20211022171917.24363-1-fmdefrancesco@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove semaphore "xmit_sema" from "struct adapter" because it is
initialized but never used.
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Link: https://lore.kernel.org/r/20211022101028.30367-2-fmdefrancesco@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some properties missing in 'cpus' node for this SoC:
- '#address-cells'
- '#size-cells'
- 'device_type' and 'reg' in child cpu nodes.
Hence, add them all to the device tree file.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20211022095203.9343-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warns:
drivers/iio/frequency/adrf6780.c:117:1: error: all paths through this
function will call itself [-Werror,-Winfinite-recursion]
{
^
drivers/iio/frequency/adrf6780.c:138:1: error: all paths through this
function will call itself [-Werror,-Winfinite-recursion]
{
^
2 errors generated.
The underscore variants should be used here.
Link: https://github.com/ClangBuiltLinux/linux/issues/1490
Fixes: 63aaf6d06d ("iio: frequency: adrf6780: add support for ADRF6780")
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211022195656.1513147-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New device support
* adrf6780 microwave upconverter.
- New driver for this interesting device including bindings.
Features
* lite-on ltr501
- Add dt-bindings including vendor ID and of_device_id table.
- Add regulator support.
* sensiron,scd4x
- Add reporting of channel scale.
Cleanups including fixes for things in this cycle
* Tree wide: Another set of dev_err_probe() introductions to reduce
noise in logs when deferred probing is needed and provide more debug
info. Devices included this time:
- amlogic,meson_saradc
- capella,cm3605
- fsl,imx7d
- maxim,max1118
- maxim,max1241
- nxp,lpc18xx
- qcom,pm8xxxx-xoadc
- rockchip,saradc
- sharp,gp2ap002
- sterricson,ab8500
- ti,ads7950
* core - iio:buffer
- Fix a path where a ret value is not intialized.
* channel-mux
- Add support to mux core subsystem for a settling delay and use
it in the iio-channel-mux driver.
- Fix a few dt binding warnings.
* nxp,lpc18xx
- Convert to devm_ functions for all of probe and drop remove()
* st,lsm6dsx
- Suppress a warning due to lack of handling of an enum *_MAX entry
that is just there to get the size.
* st,stm32-adc
- Add generic channel binding, deprecating the old approach.
- Add nvmem support to get calibration data for the vrefint channel and
use it to perform such calibration.
- Add a binding for sample-time to the generic channel description as it
can be per channel.
* ti,adc128s052
- Use devm_ managed functions and drop remove()
* vti,sca3000
- Use sign_extend32() rather than opencoding.
* xilinx,xadc
- Drop irq field from state structure as now just used in probe.
-----BEGIN PGP SIGNATURE-----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=XWvW
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.16b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
2nd set of IIO new driver, cleanups and features for the 5.16 cycle
New device support
* adrf6780 microwave upconverter.
- New driver for this interesting device including bindings.
Features
* lite-on ltr501
- Add dt-bindings including vendor ID and of_device_id table.
- Add regulator support.
* sensiron,scd4x
- Add reporting of channel scale.
Cleanups including fixes for things in this cycle
* Tree wide: Another set of dev_err_probe() introductions to reduce
noise in logs when deferred probing is needed and provide more debug
info. Devices included this time:
- amlogic,meson_saradc
- capella,cm3605
- fsl,imx7d
- maxim,max1118
- maxim,max1241
- nxp,lpc18xx
- qcom,pm8xxxx-xoadc
- rockchip,saradc
- sharp,gp2ap002
- sterricson,ab8500
- ti,ads7950
* core - iio:buffer
- Fix a path where a ret value is not intialized.
* channel-mux
- Add support to mux core subsystem for a settling delay and use
it in the iio-channel-mux driver.
- Fix a few dt binding warnings.
* nxp,lpc18xx
- Convert to devm_ functions for all of probe and drop remove()
* st,lsm6dsx
- Suppress a warning due to lack of handling of an enum *_MAX entry
that is just there to get the size.
* st,stm32-adc
- Add generic channel binding, deprecating the old approach.
- Add nvmem support to get calibration data for the vrefint channel and
use it to perform such calibration.
- Add a binding for sample-time to the generic channel description as it
can be per channel.
* ti,adc128s052
- Use devm_ managed functions and drop remove()
* vti,sca3000
- Use sign_extend32() rather than opencoding.
* xilinx,xadc
- Drop irq field from state structure as now just used in probe.
* tag 'iio-for-5.16b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (36 commits)
dt-bindings: iio: frequency: add adrf6780 doc
iio: frequency: adrf6780: add support for ADRF6780
iio: chemical: scd4x: Add a scale for the co2 concentration reading
dt-bindings: iio: io-channel-mux: allow duplicate channel, labels
dt-bindings: iio: io-channel-mux: add optional #io-channel-cells
iio: adc: adc128s052: Simplify adc128_probe()
iio: multiplexer: iio-mux: Support settle-time-us property
dt-bindings: iio: io-channel-mux: Add property for settle time
mux: add support for delay after muxing
iio: adc: stm32-adc: use generic binding for sample-time
iio: adc: stm32-adc: add vrefint calibration support
iio: adc: stm32-adc: add support of internal channels
iio: adc: stm32-adc: add support of generic channels binding
iio: adc: stm32-adc: split channel init into several routines
dt-bindings: iio: stm32-adc: add nvmem support for vrefint internal channel
dt-bindings: iio: stm32-adc: add generic channel binding
iio: accel: sca3000: Use sign_extend32() instead of opencoding sign extension.
iio: xilinx-xadc: Remove `irq` field from state struct
iio: imu: st_lsm6dsx: Avoid potential array overflow in st_lsm6dsx_set_odr()
iio: light: gp2ap002: Make use of the helper function dev_err_probe()
...
As these are very late in the 5.15 cycle and non are particularly urgent,
they can wait for the merge window.
Key element in this set is Yang Yingliang has identified a number of
issues in error paths introduced recently when we added multiple
buffer support.
Other fixes:
* adi,ad5662
- Fix handling of i2c_master_send() return value.
* adi,ad5766
- Fix a wrong dt-property name that indicated wrong units and
did not mach the bindings.
- Associated 'fix' of the bindings example to have a possible scale.
* st,pressure-spi
- Add some missing entries to the spi_device_id table to ensure
auto-loading works.
* ti,tsc2046
- Fix a backwards comparison leading to a false dev_warn
-----BEGIN PGP SIGNATURE-----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=jYCH
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.16a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
First set of IIO fixes for the 5.16 cycle
As these are very late in the 5.15 cycle and non are particularly urgent,
they can wait for the merge window.
Key element in this set is Yang Yingliang has identified a number of
issues in error paths introduced recently when we added multiple
buffer support.
Other fixes:
* adi,ad5662
- Fix handling of i2c_master_send() return value.
* adi,ad5766
- Fix a wrong dt-property name that indicated wrong units and
did not mach the bindings.
- Associated 'fix' of the bindings example to have a possible scale.
* st,pressure-spi
- Add some missing entries to the spi_device_id table to ensure
auto-loading works.
* ti,tsc2046
- Fix a backwards comparison leading to a false dev_warn
* tag 'iio-fixes-for-5.16a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: buffer: Fix memory leak in iio_buffers_alloc_sysfs_and_mask()
iio: adc: tsc2046: fix scan interval warning
iio: core: fix double free in iio_device_unregister_sysfs()
iio: core: check return value when calling dev_set_name()
iio: buffer: Fix memory leak in iio_buffer_register_legacy_sysfs_groups()
iio: buffer: Fix double-free in iio_buffers_alloc_sysfs_and_mask()
iio: buffer: Fix memory leak in __iio_buffer_alloc_sysfs_and_mask()
iio: buffer: check return value of kstrdup_const()
iio: dac: ad5446: Fix ad5622_write() return value
Documentation:devicetree:bindings:iio:dac: Fix val
drivers: iio: dac: ad5766: Fix dt property name
iio: st_pressure_spi: Add missing entries SPI to device ID table
When CONFIG_INPUT is disabled, this driver now fails to link:
ld.lld: error: undefined symbol: devm_input_allocate_device
>>> referenced by system76_acpi.c
>>> platform/x86/system76_acpi.o:(system76_add) in archive drivers/built-in.a
ld.lld: error: undefined symbol: input_set_capability
>>> referenced by system76_acpi.c
>>> platform/x86/system76_acpi.o:(system76_add) in archive drivers/built-in.a
ld.lld: error: undefined symbol: devm_hwmon_device_register_with_info
>>> referenced by system76_acpi.c
>>> platform/x86/system76_acpi.o:(system76_add) in archive drivers/built-in.a
ld.lld: error: undefined symbol: battery_hook_unregister
>>> referenced by system76_acpi.c
>>> platform/x86/system76_acpi.o:(system76_remove) in archive drivers/built-in.a
Add Kconfig dependencies for each of these three.
Fixes: 0de30fc684 ("platform/x86: system76_acpi: Replace Fn+F2 function for OLED models")
Fixes: 95563d45b5 ("platform/x86: system76_acpi: Report temperature and fan speed")
Fixes: 76f7eba3e0 ("platform/x86: system76_acpi: Add battery charging thresholds")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211022154901.904984-1-arnd@kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
It turns out that systemd-logind by default listens for KEY_RESTART input
events and reboots the machine, which isn't great - So use KEY_VENDOR for
the vendor specific identify button instead to not conflict.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Link: https://lore.kernel.org/r/20211022124612.19780-1-peter@korsgaard.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Documentation/kbuild/makefiles.rst suggests to use "archclean" for
cleaning arch/$(SRCARCH)/boot/, but it is not a hard requirement.
Since commit d92cc4d516 ("kbuild: require all architectures to have
arch/$(SRCARCH)/Kbuild"), we can use the "subdir- += boot" trick for
all architectures. This can take advantage of the parallel option (-j)
for "make clean".
I also cleaned up the comments in arch/$(SRCARCH)/Makefile. The "archdep"
target no longer exists.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
The vsyscall directory is cleaned up by the ordinary way
via arch/sh/kernel/Makefile:
obj-$(CONFIG_VSYSCALL) += vsyscall/
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Cpio format reserves 8 bytes for an ASCII representation of a time_t timestamp.
While 2106-02-07 06:28:15 UTC (time_t = 0xffffffff) is still some years in the
future, a poorly chosen date string for KBUILD_BUILD_TIMESTAMP, converted into
seconds since the epoch, might lead to exceeded cpio timestamp limits that
result in a broken cpio archive. Add timestamp checks to prevent overrun of
the 8-byte cpio header field.
My colleague Thomas Kühnel discovered the behaviour, when we accidentally fed
SOURCE_DATE_EPOCH to KBUILD_BUILD_TIMESTAMP as is: some timestamps (e.g.
1607420928 = 2021-12-08 9:48:48 UTC) will be interpreted by `date` as a valid
date specification of science fictional times (here: year 160742). Even though
this is bad input for KBUILD_BUILD_TIMESTAMP, it should not break the initramfs
cpio format.
Signed-off-by: Nicolas Schier <nicolas@fjasle.eu>
Cc: Thomas Kühnel <thomas.kuehnel@avm.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
To slim down the top Makefile, split out the code block surrounded by
ifdef CONFIG_DEBUG_INFO ... endif.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nick Desaulniers <ndesauniers@google.com>
Reviewed-by: Sedat Dilek <sedat.dilek@gmail.com>
rename node to comply with dt-schema
Fix warning:
arch/arm/boot/dts/qcom-ipq8064-rb3011.dt.yaml: s25fl016k@0: $nodename:0: 's25fl016k@0' does not match '^flash(@.*)?$'
From schema: Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211020204145.235050-1-david@ixit.cz
MMC nodes has to be named mmc@ to comply with dt-bindings.
Fix warnings as:
arch/arm/boot/dts/qcom-msm8660-surf.dt.yaml: sdcc@12400000: $nodename:0: 'sdcc@12400000' does not match '^mmc(@.*)?$'
From schema: Documentation/devicetree/bindings/mmc/arm,pl18x.yaml
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211020201440.229196-1-david@ixit.cz
Fixes warnings regarding to memory and mdio nodes and
apply new naming following dt-schema.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211020214741.261509-1-david@ixit.cz
The Nexus 4 (mako) was accidentally described as a Asus device, while it's LG.
Fixes: 9304af37d0 ("dt-bindings: arm: qcom, add missing devices")
Signed-off-by: David Heidelberg <david@ixit.cz>
[bjorn: Updated commit message, per suggestion from Konrad Dybcio]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211020001327.37490-1-david@ixit.cz
Version dk01.1-c1 didn't have compatible specified, which was
causing dt-schema validation warnings.
Remove duplicated and useless board compatible from dtsi between board and device.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211009193102.76852-2-david@ixit.cz
One board version (dk01.1-c1) didn't have set device compatible,
so let's list it.
Signed-off-by: David Heidelberg <david@ixit.cz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211009193102.76852-1-david@ixit.cz
In order to avoid having prefixes for multiple internal divisions of LG
use the "lg" prefix instead of "lge".
Fixes: ad3f04b7be ("ARM: dts: qcom: Add support for LG G Watch R")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928203815.77175-2-luca@z3ntu.xyz
In order to avoid having prefixes for multiple internal divisions of LG
use the "lg" prefix instead of "lge".
Fixes: 21f3cbf693 ("dt-bindings: arm: qcom: Document APQ8026 SoC binding")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: David Heidelberg <david@ixit.cz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928203815.77175-1-luca@z3ntu.xyz
'#clock-cells' is a required property of QMP PHY child node, not itself.
Drop it to fix the dtbs_check warnings below.
qcom-sdx55-t55.dt.yaml: phy@ff6000: '#clock-cells' does not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+'
qcom-sdx55-mtp.dt.yaml: phy@ff6000: '#clock-cells' does not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+'
qcom-sdx55-telit-fn980-tlb.dt.yaml: phy@ff6000: '#clock-cells' does not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+'
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210929034253.24570-11-shawn.guo@linaro.org
Add qcom,msm-id and qcom,board-id for Robotics Board RB5.
This will help us boot the device with newer Android boot
image header versions, which package dtb separately
instead of the default Image.gz-dtb (appended dtb) format.
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210930185742.117928-2-amit.pundir@linaro.org
Add qcom,msm-id and qcom,board-id for Dragonboard 845c.
This will help us boot the device with newer Android boot
image header versions, which package dtb separately
instead of the default Image.gz-dtb (appended dtb) format.
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210930185742.117928-1-amit.pundir@linaro.org
Almost any board that boots and has a way to interact with it
(say for the rare cases of just-pstore or let's-rely-on-bootloader-setup)
needs to set some GPIOs, so it makes no sense to include gpio.h separately
each time. Hence move it to SoC DTSI.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211002001358.45920-6-konrad.dybcio@somainline.org
Add the aforementioned properties in the SoC DTSI so that everybody doesn't
have to copy that into their device DTs, effectively reducing code
duplication.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211002001358.45920-5-konrad.dybcio@somainline.org
DPU/MDSS is borderline useless without MDP, so disabling
both of them makes little sense. With this change, enabling
mdss will be enough.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211002001358.45920-4-konrad.dybcio@somainline.org
