The FIFO guarantee is only there if two timers are queued into the
same bucket at the same jiffie on the same cpu:
- The slack value depends on the delta between expiry and enqueue
time, so the resulting expiry time can be different for timers
which are queued in different jiffies.
- Timers which are queued into the secondary array end up after a
later queued timer which was queued into the primary array due to
cascading.
- Timers can end up on different cpus due to the NOHZ target moving
around. Obviously there is no guarantee of expiry ordering between
cpus.
So anything which relies on FIFO behaviour of the timer wheel is
broken already.
This is a preparatory patch for converting the timer wheel to hlist
which reduces the memory foot print of the wheel by 50%.
It's a seperate patch so any (unlikely to happen) regression caused by
this can be identified clearly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Joonwoo Park <joonwoop@codeaurora.org>
Cc: Wenbo Wang <wenbo.wang@memblaze.com>
Cc: George Spelvin <linux@horizon.com>
Link: http://lkml.kernel.org/r/20150526224511.757520403@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
catchup_timer_jiffies() has been applied blindly to several functions
without looking for possible better ways to do it.
1) internal_add_timer()
Move the update to base->all_timers before we actually insert the
timer into the wheel.
2) detach_if_pending()
Again the update to base->all_timers allows us to explicitely do
the timer_jiffies update in place, if this was the last timer which
got removed.
3) __run_timers()
We only check on entry, which is silly, because base->timer_jiffies
can be behind - especially on NOHZ kernels - and if there is a
single deferrable timer somewhere between base->timer_jiffies and
jiffies we expire it and then loop until base->timer_jiffies ==
jiffies.
Move it into the loop.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Joonwoo Park <joonwoop@codeaurora.org>
Cc: Wenbo Wang <wenbo.wang@memblaze.com>
Link: http://lkml.kernel.org/r/20150526224511.662994644@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix the PERIPHERAL_MAX_SHIFT definition (3 instead of 4) and adapt the
round_rate and set_rate logic accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: "Wu, Songjun" <Songjun.Wu@atmel.com>
The PLL impose a certain input range to work correctly, but it appears that
this input range does not apply on the input clock (or parent clock) but
on the input clock after it has passed the PLL divisor.
Fix the implementation accordingly.
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Jonas Andersson <jonas@microbit.se>
This patch allows the block allocation code to retain the buffers
for the resource groups so they don't need to be re-read from buffer
cache with every request. This is a performance improvement that's
especially noticeable when resource groups are very large. For
example, with 2GB resource groups and 4K blocks, there can be 33
blocks for every resource group. This patch allows those 33 buffers
to be kept around and not read in and thrown away with every
operation. The buffers are released when the resource group is
either synced or invalidated.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Reviewed-by: Steven Whitehouse <swhiteho@redhat.com>
Reviewed-by: Benjamin Marzinski <bmarzins@redhat.com>
These have been register compatible so far. However ARCv2 mandates
different pt_regs layout (due to h/w auto save). To keep pt_regs same
for both, we start by removing the assumption - used mainly for block
copies between the 2 structs in signal handling and ptrace
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Previously this macro was overloaded with stack switching, saving SP at right
slot in pt_regs, saving/setup of r25 and setting SP baseline to where
pt_regs->sp is saved (vs. bottom of pt_regs)
Now it only does SP switch, and leaves SP pointing to bottom of pt_regs.
r25 saving is no longer done here to allow for future reordering of
regfile in pt_regs w/o touching this macro
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Returning from pure kernel mode and exception mode use the same code
anyways. Remove one the duplicate blocks
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Elide the need to re-read ECR in Trap handler by ensuring that
EXCEPTION_PROLOGUE does that at the very end just before returning
to Trap handler
ARCv2 EXCEPTION_PROLOGUE already did that, so same for ARcompact and the
common trap handler adjusted to use cached ECR
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This fixes the possible link/relo errors, since restore_regs will be
provided by ISA code, but called from ARC common code.
The .L prefix reassures binutils that it will be in same compilation
unit.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- Remove the ifdef'ery and write distinct versions for each mmu ver even
if there is some code duplication
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
That is because __after_dc_op() already reads it for status check, so it
is better anyways to use that "newer" value.
Also reduces the clutter in callers for passing from/to these routines.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
As DW Mobile Storage databook says it's required to use "Hold Register"
if card is enumerated in SDR12 or SDR25 modes.
It means we need to act in the same way as in Altera's Socfpga
implementation - set "use hold reg" bit in commad.
Note that for upstream proper solution would be to remove
dw_mci_pltfm_prepare_command() at all and set the bit right in
dw_mci_prepare_command() for all platforms.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Earlycon calculates UART clock as "BASE_BAUD * 16". In case of ARC
"BASE_BAUD" is calculated dynamically in runtime, basically it is an
alias to arc_early_base_baud(), which in turn just does
"arc_base_baud/16".
8250 UART on AXS/SDP board uses 33.3MHz clock source which is set in
"arc_base_baud" with this change.
Additional compatibility string "snps,arc-sdp" is introduced as well
because there're different flavours of AXS boards but they all share the
same motherboard and so it's possible to re-use the same code for
motherbord even if CPU daughterboard changes.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The AXS10x platforms consist of a mainboard with peripherals,
on which several daughter cards can be placed. The daughter cards
typically contain a CPU and memory.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Currently, it doesn't invoke the callback but continues to unwind
Also while at it - simplify the code a bit
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Directly return the result of perf_pmu_register() in
arc_pmu_device_probe() instead of assigning and returning variable ret.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
static arc_pmu in the arch/arc/kernel/perf_event.c is not initialized as
it's shadowed by a local variable of the same name in the
arc_pmu_device_probe.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Fixes: 03c94fcf95 "ARC: perf: make @arc_pmu static global"
CC: <stable@vger.kernel.org> # 4.1
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* Remove remanants of legacy ARC FPGA platforms (AA4, ML509...)
* Only nsim simulation platform is left, rename platform accordingly
* AA4 DT stuff is compatible with nsim for ARC700 so rename it too
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Back when ARC700 4.10 was released, the related kernel features were
tied to this config item so they could be disabled in one shot (i.e.
LLOCK/SCOND, SWAPE, RTSC..)
That having happened a while back, all new ARC customers weill get 4.11+
so those features can be assumed to be present and need not be tied to a
top-level (we still retain the ability to individually disable them).
Further, since ARCv2 also shares some of those feautes, removing it
simplifies things a bit in Kconfig
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
drivers/cpufreq/cpufreq.c is already using this function. And now btrfs
needs it as well. Export symbol kobject_move().
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David Sterba <dsterba@suse.cz>
This patch will add support to show the replacing target in sysfs
during the process of replacement.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.cz>
When btrfs on a device is overwritten with a new btrfs (mkfs),
the old btrfs instance in the kernel becomes stale. So with this
patch, if kernel finds device is overwritten then delete the stale
fsid/uuid.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
The rate controls are codec-specific, it's not possible to
generically say what the range or the meaning of each control
is (or even if they exist at all) - that depends on the
particular codec.
This is currently being handled for Arizona codecs by putting
an Arizona-specific table of controls inside the wm_adsp driver.
This creates a dependency between wm_adsp and arizona.c, and is an
awkward solution if the ADSP is used in another family of codecs
Fix this by moving the Arizona-specific rate controls into the
Arizona codec drivers.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sine commit 269ad8015a ("sched/deadline: Avoid double-accounting in
case of missed deadlines), parameter 'rq' is no longer used, so
remove it.
Signed-off-by: Zhiqiang Zhang <zhangzhiqiang.zhang@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <juri.lelli@gmail.com>
Cc: <luca.abeni@unitn.it>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1434338120-43773-1-git-send-email-zhangzhiqiang.zhang@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Resetting the p->dl_throttled flag in rt_mutex_setprio() (for a task that is going
to be boosted) is superfluous, as the natural place to do so is in
replenish_dl_entity().
If the task was on the runqueue and it is boosted by a DL task, it will be enqueued
back with ENQUEUE_REPLENISH flag set, which can guarantee that dl_throttled is
reset in replenish_dl_entity().
This patch drops the resetting of throttled status in function rt_mutex_setprio().
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1431496867-4194-6-git-send-email-wanpeng.li@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
