A construct like:
if (pm_runtime_suspended(twl->dev))
pm_runtime_get_sync(twl->dev);
is against the spirit of the runtime_pm interface as it
makes the internal refcounting useless.
In this case it is also racy, particularly as 'put_autosuspend'
is used to drop a reference.
When that happens a timer is started and the device is
runtime-suspended after the timeout.
If the above code runs in this window, the device will not be
found to be suspended so no pm_runtime reference is taken.
When the timer expires the device will be suspended, which is
against the intention of the code.
So be more direct is taking and dropping references.
If twl->linkstat is VBUS_VALID or ID_GROUND, then hold a
pm_runtime reference, otherwise don't.
Define "cable_present()" to test for this condition.
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In hardware mode we can not use the software demuxer, this means that the
selected scan mask needs to match one of the available scan masks exactly.
It also means that all attached buffers need to use the same scan mask.
Given that when operating in hardware mode there is typically only a single
buffer attached to the device this not an issue. Add a sanity check to make
sure that only a single buffer is attached in hardware mode nevertheless.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
For each buffer type specify the supported device modes for this buffer.
This allows us for devices which support multiple different operating modes
to pick the correct operating mode based on the modes supported by the
attached buffers.
It also prevents that buffers with conflicting modes are attached
to a device at the same time or that a buffer with a non-supported mode is
attached to a device (e.g. in-kernel callback buffer to a device only
supporting hardware mode).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
All ARMv5 and older CPUs invalidate their caches in the early assembly
setup function, prior to enabling the MMU. This is because the L1
cache should not contain any data relevant to the execution of the
kernel at this point; all data should have been flushed out to memory.
This requirement should also be true for ARMv6 and ARMv7 CPUs - indeed,
these typically do not search their caches when caching is disabled (as
it needs to be when the MMU is disabled) so this change should be safe.
ARMv7 allows there to be CPUs which search their caches while caching is
disabled, and it's permitted that the cache is uninitialised at boot;
for these, the architecture reference manual requires that an
implementation specific code sequence is used immediately after reset
to ensure that the cache is placed into a sane state. Such
functionality is definitely outside the remit of the Linux kernel, and
must be done by the SoC's firmware before _any_ CPU gets to the Linux
kernel.
Changing the data cache clean+invalidate to a mere invalidate allows us
to get rid of a lot of platform specific hacks around this issue for
their secondary CPU bringup paths - some of which were buggy.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The generic RZ CPG compatible value is mandatory, as the driver uses
only this value for matching. Document that this is a fallback that
must be present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The generic R-Car Gen2 CPG compatible value is mandatory, as the driver
uses only this value for matching. Document that this is a fallback
that must be present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The generic MSTP gate clocks compatible value is mandatory, as the
driver uses only this value for matching. Document that this is a
fallback that must be present.
Also fix a typo (missing plural "s") in the compatible value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Even if no userspace consumer buffer is attached to the IIO device at
registration we still need to compute the masklength, since it is possible
that a in-kernel consumer buffer is going to get attached to the device at
a later point.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix the module_param "instances" type to uint, since the variable type
holding the value is unsigned.
Signed-off-by: Vladimirs Ambrosovs <rodriguez.twister@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The functions iio_dummy_remove(), iio_simple_dummy_events_unregister() and
iio_dummy_evgen_release_irq() were changed to return void instead of int.
Signed-off-by: Vladimirs Ambrosovs <rodriguez.twister@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The generic CPG DIV6 clock compatible value is mandatory, as the driver
uses only this value for matching. Document that this is a fallback
that must be present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the init function for the iio_simple_dummy driver.
The main issues were absence of kfree for the allocated array, and no
devices being removed in case the probe function fails, running in a loop.
Signed-off-by: Vladimirs Ambrosovs <rodriguez.twister@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Model name in mt8173-evb.dts doesn't follow dts convention (it should
be human readable model name). Fix it.
Fixes: b3a3724841 ("arm64: dts: Add mediatek MT8173 SoC and evaluation board dts and Makefile")
Cc: <stable@vger.kernel.org> # v4.0+
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The A20 has a few SRAM that can be mapped either to a device or to the CPU,
with the mapping being controlled by a SRAM controller.
Add the SRAM controller, the SRAM that it drives and the section that can
be used by the various devices.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
The A10s and A13 have a few SRAM that can be mapped either to a device or
to the CPU, with the mapping being controlled by a SRAM controller.
Add the SRAM controller, the SRAM that it drives and the section that can
be used by the various devices.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
The A10 has a few SRAM that can be mapped either to a device or to the CPU,
with the mapping being controlled by a SRAM controller.
Add the SRAM controller, the SRAM that it drives and the section that can
be used by the various devices.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
This patch reverts commit ccb4ada2f1 ("ARM: dts: sun7i: Add A20 SRAM and
SRAM controller"), commit e6f51e4bd2 ("ARM: dts: sun5i: Add A13 and A10s
SRAM and SRAM controller") and commit 6d92b80f35 ("ARM: dts: sun4i: Add
A10 SRAM and SRAM controller").
The bindings have been changed in the SRAM driver, and we need to
change the DT accordingly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On A80 there are 2 watchdogs, one in the main block, and one in the
R (special) block. We do not have information on the R block watchdog,
other than the register layout is the same, and the interrupt number.
Both are able to reset the whole system.
Add the main watchdog, in case the R block is used for special purposes
like running an RTOS.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The BananaPro uses uart4 for the default rx/tx pins on the 40 pins connector,
so enable uart4.
Uart2 is also available at the bananapro io-pins, but like on the bananapi
the primary function of the pins is to act as gpios, see:
http://forum.lemaker.org/forum.php?mod=viewthread&tid=10852
Remove the uart2 node, people who want to use uart2 can do so with a
devicetree-overlay.
Signed-off-by: Michael Ring <mail@michael-ring.org>
[hdegoede@redhat.com: Remove uart2 node]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some boards (e.g. the BananaPro) use alternative pins for uart4, add a pinmux
entry for these.
Signed-off-by: Michael Ring <mail@michael-ring.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A23 Evaluation Board has an MMC slot, two UARTs, NAND, a few display
connectors (RGB, MIPI, LVDS), a mini-PCIE slot, USB host and OTG and a
bunch of embedded sensors.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The changeset dc9ef7d112 change the open() ioctl documentation to
match the V4L2 open(). However, some cut-and-pasted stuff doesn't
match what actually happens at the DVB core.
So, fix the documentation entry to be more accurate with the DVB
frontend open() specifics.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Due to a typo the illegal access interrupt is never cleared in by
the interupt handler, causing an effective deadlock on the first
illegal access.
This was broken since the code was introduced in 5433acd81e ("MIPS:
ralink: add illegal access driver"), but only exposed when the Kconfig
symbol was added, thus enabling the code.
Cc: <stable@vger.kernel.org> [3.18+]
Fixes: a7b7aad383 ("MIPS: ralink: add missing symbol for RALINK_ILL_ACC")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/10172/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This replaces the plain loop over the sglist array with for_each_sg()
macro which consists of sg_next() function calls. Since m68k doesn't
select ARCH_HAS_SG_CHAIN, it is not necessary to use for_each_sg() in
order to loop over each sg element. But this can help find problems
with drivers that do not properly initialize their sg tables when
CONFIG_DEBUG_SG is enabled.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-arch@vger.kernel.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
To fix the last xmllint errors the open and close function reference
description was rewritten based on the v4l2 open and close functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fixes a large number of xmllint errors.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix indentation nits to make mt8173.dtsi more consistent.
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
We're currently using a fixed frequency clock specified in the DT, so
enabling is a no-op. However, the RPi firmware-based clocks driver
can actually disable unused clocks, so when switching to use it we
ended up losing our MMC clock once all devices were probed.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Apparently we can have requests even if though the active list is empty,
so do the request retirement regardless of whether there's anything
on the active list.
The way it happened here is that during suspend intel_ring_idle()
notices the olr hanging around and then proceeds to get rid of it by
adding a request. However since there was nothing on the active lists
i915_gem_retire_requests() didn't clean those up, and so the idle work
never runs, and we leave the GPU "busy" during suspend resulting in a
WARN later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
According to the HSW b-spec we need to try clock divisors of 63
and 72, each 3 or more times, when attempting DP AUX channel
communication on a server chipset. This actually wasn't happening
due to a short-circuit that only checked the DP_AUX_CH_CTL_DONE bit
in status rather than checking that the operation was done and
that DP_AUX_CH_CTL_TIME_OUT_ERROR was not set.
[v2] Implemented alternate solution suggested by Jani Nikula.
Cc: stable@vger.kernel.org
Signed-off-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The same code is executed regardless ret value, so this test
can be removed.
Also fix coverity scan CID 1268786.
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Mark strings, which are not supposed to be changed (basedir, filename,
value), as const in function parameters.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In generic_buffer.c: sort program parameters alphabetically and provide
usage information
In lsiio.c: drop unused parameters
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In build_channel_array(), count can be initialized already during variable
declaration.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In iioutils_get_type() it is logically better fitting to have sysfsfp
assigned zero right after closing it.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Change the assignment of *is_signed in iioutils_get_type() to a one-liner,
as already done with *be.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Refactor the code in print_event() to reduce code duplication and better
reflect that the type is output unconditionally, as well as cascade the
dependency of the diff-channel. Saves a few lines of code, as well.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
With se_port_t and t10_alua_tg_pt_gp_member being absored into se_lun,
there is no need for an extra atomic_t based reference count for PR
ALL_TG_PT=1 and ALUA access state transition.
Go ahead and use the existing percpu se_lun->lun_ref instead, and
convert the two special cases to percpu_ref_tryget_live() to avoid
se_lun if transport_clear_lun_ref() has already been invoked to
shutdown the se_lun.
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
With se_port and t10_alua_tg_pt_gp_member being absored into se_lun,
there is no need for an extra lock to protect se_lun->lun_se_dev
assignment.
This patch also converts backend drivers to use call_rcu() release
to allow any se_device readers to complete. The call_rcu() instead
of kfree_rcu() is required here because se_device is embedded into
the backend driver specific structure.
Also, convert se_lun->lun_stats to use atomic_long_t within the
target_complete_ok_work() completion callback, and add FIXME for
transport_lookup_tmr_lun() with se_lun->lun_ref.
Finally, update sbp_update_unit_directory() special case usage with
proper rcu_dereference_raw() and configfs symlink comment.
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Chris Boot <bootc@bootc.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch eliminates all se_port + t10_alua_tg_pt_gp_member usage,
and converts current users to direct se_lun pointer dereference.
This includes the removal of core_export_port(), core_release_port()
core_dev_export() and core_dev_unexport(). Along with conversion
of special case se_lun pointer dereference within PR ALL_TG_PT=1
and ALUA access state transition UNIT_ATTENTION handling.
Also, update core_enable_device_list_for_node() to reference the
new per se_lun->lun_deve_list when creating a new entry, or
replacing an existing one via RCU.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
