sdm845 uses dmic on EC so it should select CROS_EC_CODEC.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to RM SPDIF STC SYSCLK_DF field is 9-bit wide, values
being in 0..511 range. Use a proper type to handle sysclk_df.
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The on-chip PLL can be disabled if on the MCLKI pin we have an external
clock at 512 x fs. This clock can be used as direct internal clock for
ADCs or DACs.
To support this, we add an extra clock id that can be configured
using the set_sysclk() callback.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver only supports DPS_A for DAC, which is configured at probe.
This patch adds support for DSP_A and I2S modes by using the set_fmt()
callback.
A trivial break is also removed from a case's default branch.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
By default, the codec starts to interpret the left (first) channel on
the falling edge (low polarity) of LRCLK. However, for DSP_A, the left
channel needs to start on the rising edge of LRCLK. This patch fixes
this channel swap by toggling the bit which selects the LRCLK polarity.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DACs and ADCs on ad193x codecs require a 32 bit slot size. We should
assure that no other size is used.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some ad193x codecs don't have ADCs, so they have no capture capabilities.
This way, we can use this driver in multicodec cards.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Have kprobes not use copy_from_user() to access kernel addresses,
because kprobes can legitimately poke at bad kernel memory, which
will fault. Copy from user code should never fault in kernel space.
Using probe_mem_read() can handle kernel address space faulting.
- Put back the entries counter in the tracing output that was accidentally
removed.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXGb7BxQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qqvaAQC66gQ79frSW7xPjJ4Y+qLIm0YDV18i
aCHowAXxDeK3qAEA3sDeELAPVupacPrzZc6zejI+bf0HArPe08n3vlHwAQw=
=uUQj
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.0-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Two more tracing fixes
- Have kprobes not use copy_from_user() to access kernel addresses,
because kprobes can legitimately poke at bad kernel memory, which
will fault. Copy from user code should never fault in kernel space.
Using probe_mem_read() can handle kernel address space faulting.
- Put back the entries counter in the tracing output that was
accidentally removed"
* tag 'trace-v5.0-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix number of entries in trace header
kprobe: Do not use uaccess functions to access kernel memory that can fault
Odroid HC1 uses the exynos5422-odroid-core.dtsi file as a base. All
other Exynos5422 Odroids use the "common". The ADC node was defined
only in the latter.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Create a separate magic16 check function so that we don't run afoul of
static checkers.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Without this, we get failures like this when the kernel attempts to
initialize a cx231xx device:
[16046.153653] cx231xx 3-1.2:1.1: New device Hauppauge Hauppauge Device @ 480 Mbps (2040:c200) with 6 interfaces
[16046.153900] cx231xx 3-1.2:1.1: can't change interface 3 alt no. to 3: Max. Pkt size = 0
[16046.153907] cx231xx 3-1.2:1.1: Identified as Hauppauge USB Live 2 (card=9)
[16046.154350] i2c i2c-11: Added multiplexed i2c bus 13
[16046.154379] i2c i2c-11: Added multiplexed i2c bus 14
[16046.267194] cx25840 10-0044: cx23102 A/V decoder found @ 0x88 (cx231xx #0-0)
[16048.424551] cx25840 10-0044: loaded v4l-cx231xx-avcore-01.fw firmware (16382 bytes)
[16048.463224] cx231xx 3-1.2:1.1: v4l2 driver version 0.0.3
[16048.567878] cx231xx 3-1.2:1.1: Registered video device video2 [v4l2]
[16048.568001] cx231xx 3-1.2:1.1: Registered VBI device vbi0
[16048.568419] cx231xx 3-1.2:1.1: audio EndPoint Addr 0x83, Alternate settings: 3
[16048.568425] cx231xx 3-1.2:1.1: video EndPoint Addr 0x84, Alternate settings: 5
[16048.568431] cx231xx 3-1.2:1.1: VBI EndPoint Addr 0x85, Alternate settings: 2
[16048.568436] cx231xx 3-1.2:1.1: sliced CC EndPoint Addr 0x86, Alternate settings: 2
[16048.568448] usb 3-1.2: couldn't get decoder output pad for V4L I/O
[16048.568453] cx231xx 3-1.2:1.1: V4L2 device vbi0 deregistered
[16048.568579] cx231xx 3-1.2:1.1: V4L2 device video2 deregistered
[16048.569001] cx231xx: probe of 3-1.2:1.1 failed with error -22
Likely a regession since Commit 9d6d20e652
("media: v4l2-mc: switch it to use the new approach to setup pipelines")
(v4.19-rc1-100-g9d6d20e652c0), which introduced the use of
PAD_SIGNAL_DV within v4l2_mc_create_media_graph().
This also modifies cx25840 to remove the VBI pad, matching the action
taken in Commit 092a37875a ("media: v4l2: remove VBI output pad").
Fixes: 9d6d20e652 ("media: v4l2-mc: switch it to use the new approach to setup pipelines")
Cc: stable@vger.kernel.org
Signed-off-by: Cody P Schafer <dev@codyps.com>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is a spelling mistake in a fmdbg debug message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media_device_cleanup() wasn't called, which caused a small
memory leak.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the media device registration fails, don't call media_device_unregister
since the device was never actually registered.
When removing the module also call media_device_cleanup() to avoid a memory leak.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is a remnant of commit 70a7fb80e8 ("regulator: core: Fix nested
locking of supplies").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch makes the SoC camera framework as well as effectively the few
remaining sensor drivers depend on BROKEN, rendering it uncompileable
without changes in Kconfig.
The purpose is to leave the code around if someone wishes to convert the
drivers to the modern day V4L2 sub-device framework without having to go
to see development history in git.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move the mt9t031 driver to the soc_camera directory in the media staging
tree.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move the imx074 driver to the soc_camera directory in the media staging
tree.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This fixes another set of errors from the refactoring of literals
to mask preproccesor definitions.
Found by debugging a broken voltage setup on Orange Pi One Plus.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SoC camera framework has no functional drivers left, something that
has not changed for years. Move the leftovers to the staging tree.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is a V4L2 sub-device sensor driver for the rj45n1.
As there is already another driver, remove the SoC camera one.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a V4L2 sub-device sensor driver for the mt9m001.
There is already a non-soc_camera driver. So, remove the SoC camera
one.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The authorize reply can be empty, for example when the ticket used to
build the authorizer is too old and TAG_BADAUTHORIZER is returned from
the service. Calling ->verify_authorizer_reply() results in an attempt
to decrypt and validate (somewhat) random data in au->buf (most likely
the signature block from calc_signature()), which fails and ends up in
con_fault_finish() with !con->auth_retry. The ticket isn't invalidated
and the connection is retried again and again until a new ticket is
obtained from the monitor:
libceph: osd2 192.168.122.1:6809 bad authorize reply
libceph: osd2 192.168.122.1:6809 bad authorize reply
libceph: osd2 192.168.122.1:6809 bad authorize reply
libceph: osd2 192.168.122.1:6809 bad authorize reply
Let TAG_BADAUTHORIZER handler kick in and increment con->auth_retry.
Cc: stable@vger.kernel.org
Fixes: 5c056fdc5b ("libceph: verify authorize reply on connect")
Link: https://tracker.ceph.com/issues/20164
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Now that we have 3 mmap flags shared by all architectures,
let's move them into the common header.
This will help discourage future architectures from duplicating code.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use linux/mman.h to make sure we get all mmap flags we need.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use linux/mman.h to make sure we get all mmap flags we need.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
RING_CONTROL reg was not written due to wrong address, hence all
the subsequent ring flush was timing out.
Fixes: a371c10ea4 ("mailbox: bcm-flexrm-mailbox: Fix FlexRM ring flush sequence")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This addresses the below TODO item, no function related changes:
- Prefix imgu for all public APIs, i.e. change ipu3_v4l2_register() to
imgu_v4l2_register(). (Sakari)
The changes were obtained by applying the following perl script
to driver code under drivers/staging/media/ipu3/.
perl -pi.back -e 's/ipu3_(?!uapi)/imgu_/g;'
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The mbox_flush() function can be used by drivers that are built as
modules, so the function needs to be exported.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
According to the ov5640 specification (2.7 power up sequence), host can
access the sensor's registers 20ms after reset. Trying to access them
before leads to undefined behavior and result in sporadic initialization
errors.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov5640_try_frame_interval operation updates the FPS as per user
input based on default ov5640_frame_rate, OV5640_30_FPS which is failed
to update when user trigger 15fps.
So, initialize the default ov5640_frame_rate to OV5640_15_FPS so-that
it can satisfy to update all fps.
Fixes: 5a3ad937bc ("media: ov5640: Make the return rate type more explicit")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The register value lists for all the supported resolution settings all
include a register address/value pair for setting the JPEG compression
mode. With the exception of 1080p (which sets mode 2), all resolutions
use mode 3.
The only difference between mode 2 and mode 3 is that mode 2 may have
padding data on the last line, while mode 3 does not add padding data.
As these register values were from dumps of running systems, and the
difference between the modes is quite small, using mode 3 for all
configurations should be OK.
[Sakari Ailus: Align OV5640_REG_JPG_MODE_SELECT register naming.]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When compression is turned on, the on-bus data is framed according to
the compression mode, and the height and width set in VFIFO_VSIZE and
VFIFO_HSIZE. If these are not updated correctly, the sensor will send
data framed in a manner unexpected by the capture interface, such as
having more bytes per line than expected, and having the extra data
dropped. This ultimately results in corrupted data.
Set the two values when the media bus is configured for JPEG data,
meaning the sensor would be in JPEG mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The OV5640 driver currently supports a static color bar pattern with a
small vertical gamma gradient. The hardware also supports a color square
pattern, as well as having a rolling bar for dynamic sequences.
Add three more test patterns:
- color bars with a rolling bar (but without the gamma gradient)
- static color squares
- color squares with a rolling bar
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The transparent feature for test patterns blends the test pattern with
an actual captured image. This makes the result non-static, subject to
changes in the sensor's field of view.
Test patterns should be predictable and deterministic, even if they are
dynamic patterns. Disable the transparent feature of the test pattern.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The OV5640 can generate many types of test patterns, some with
additional modifiers, such as a rolling bar, or gamma gradients.
Add the bit definitions for all bits in the test pattern register,
and use them to compose the values to be written to the register.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The OV5640 has many options for generating test patterns. Unfortunately
there is only one V4L2 control for it. Thus the driver would need to
list some or all combinations.
Move the test_pattern_menu list before the ov5640_set_ctrl_test_pattern
function that programs the hardware. This would allow us to add a
matching list of values to program into the hardware, while keeping the
two lists together for ease of maintenance.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV748X_PAGE_WAIT is a fake page to insert arbitrary delays in the
register tables.
Its only usage was removed, so we can remove the handling and simplify
the code.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV748x is currently reset by writting a small table of registers to
the device.
The table lacks documentation and contains magic values to perform the
actions, including using a fake register address to introduce a delay
loop.
Remove the table, and convert to code, documenting the purpose of the
specific writes along the way.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the adv748x driver is informed about a link being created from HDMI or
AFE to a CSI-2 TX output, the 'link_setup()' callback is invoked. Make
sure to implement proper routing management at link setup time, to route
the selected video stream to the desired TX output.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The 'phys_id' local variable became unused after commit
ce4b1b1650 ("x86/smpboot: Initialize secondary CPU only if master CPU will wait for it").
Remove it.
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Alison Schofield <alison.schofield@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Pu Wen <puwen@hygon.cn>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Cc: Yazen Ghannam <yazen.ghannam@amd.com>
Cc: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Link: https://lkml.kernel.org/r/1550495101-41755-1-git-send-email-zhangshaokun@hisilicon.com
Both the AFE and HDMI s_stream routines (adv748x_afe_s_stream() and
adv748x_hdmi_s_stream()) have to enable the CSI-2 TX they are streaming video
data to.
With the introduction of dynamic routing between HDMI and AFE entities to
TXA, the video stream sink needs to be set at run time, and not statically
selected as the s_stream functions are currently doing.
To fix this, store a reference to the active CSI-2 TX sink for both HDMI and
AFE sources, and operate on it when starting/stopping the stream.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The power_up_tx() procedure needs to set a few registers conditionally to
the selected video source, but it currently checks for the provided tx to
be either TXA or TXB.
With the introduction of dynamic routing between HDMI and AFE entities to
TXA, checking which TX the function is operating on is not meaningful anymore.
To fix this, store the subdevice of the source providing video data to the
CSI-2 TX in the 'struct adv748x_csi2' representing the TX and check on it.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV748x chip supports routing AFE output to either TXA or TXB.
In order to support run-time configuration of video stream path, create an
additional (not enabled) "AFE:8->TXA:0" link, and remove the IMMUTABLE flag
from existing ones.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add small is_txb() macro to the existing is_txa() and use it where
appropriate.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sd argument of this macro can be a more complex expression. Since it
is used 5 times in the macro it can be evaluated that many times as well.
So assign it to a temp variable in the beginning and use that instead.
This also avoids any potential side-effects of evaluating sd.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
