If RX is disabled while there are still unprocessed bytes in RX FIFO,
cdns_uart_handle_rx() called from interrupt handler will get stuck in
the receive loop as read bytes will not get removed from the RX FIFO
and CDNS_UART_SR_RXEMPTY bit will never get set.
Avoid the stuck handler by checking first if RX is disabled. port->lock
protects against race with RX-disabling functions.
This HW behavior was mentioned by Nathan Rossi in 43e98facc4a3 ("tty:
xuartps: Fix RX hang, and TX corruption in termios call") which fixed a
similar issue in cdns_uart_set_termios().
The behavior can also be easily verified by e.g. setting
CDNS_UART_CR_RX_DIS at the beginning of cdns_uart_handle_rx() - the
following loop will then get stuck.
Resetting the FIFO using RXRST would not set RXEMPTY either so simply
issuing a reset after RX-disable would not work.
I observe this frequently on a ZynqMP board during heavy RX load at 1M
baudrate when the reader process exits and thus RX gets disabled.
Fixes: 61ec901698 ("tty/serial: add support for Xilinx PS UART")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
unlikely has already included in IS_ERR(),
so just remove redundant likely annotation.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Combine all HCA capabilities setters under one function
and compile out the ODP related function in case kernel
was compiled without ODP support.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Polish the kerneldoc a bit with suggestions from Randy.
v2: Randy found another typo: s/compent/component/
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using dma_dev->dev for mappings before it's assigned with the correct
device is unlikely to work as expected, and with future dma-direct
changes, passing a NULL device may end up crashing entirely. I don't
know enough about this hardware or the mv_xor_prep_dma_interrupt()
operation to implement the appropriate error-handling logic that would
have revealed those dma_map_single() calls failing on arm64 for as long
as the driver has been enabled there, but moving the assignment earlier
will at least make the current code operate as intended.
Fixes: 22843545b2 ("dma: mv_xor: Add support for DMA_INTERRUPT")
Reported-by: John David Anglin <dave.anglin@bell.net>
Tested-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
With old DTS there will be missing DAPM routes linking BE with CODECs.
Add those routes in the card driver so sound works properly on Odroid
XU3/4 also without DTS updates enabling the secondary PCM.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warning:
sound/soc/codecs/wm8741.c:371:5: warning:
symbol 'wm8741_mute' was not declared. Should it be static?
Fixes: 36b1599340 ("ASoC: wm8741: Add digital mute callback")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ESAI_xCR_xWA is xCR's bit, not the xCCR's bit, driver set it to
wrong register, correct it.
Fixes 43d24e76b6 ("ASoC: fsl_esai: Add ESAI CPU DAI driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Ackedy-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A few small fixes, a driver fix for Samsung, a fix for refcounting of
of_nodes in the simple-card driver that triggered on a lot of systems
and a fix for topology error handling.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlxr49QTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0NPqB/9SIiP4GQp+PXfS3PawsSZn1klskmq4
QPUxXCq05MOnn1v/EaK1JoSVWPbOQ7IEcsjucuvTkikGQ9RdWdRKre0auWXVKdpk
dl9D5zHgoAqlQ0RjJN5vn3zNA49/wyZni2MqHytlDvVQOQbI7KZ0aSCGj1RlW0ps
k9sJCfQGmWH0f8WKnutvGBuDbu6rDyD6l+coSdjIxfTbVR6RPNWYa3ttC/ouW1XE
fsjDKRCe3OYf8/goRSpM26CWinCQMdN18OkFkBVcWEyxg8LCvQe0f8aygLMJOZQr
dY3XP5Fz3dYD2oJU5kGUBLbLhjk2/NRejhYI7VhXaKey2x6On0x4N2wH
=u/xe
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.0
A few small fixes, a driver fix for Samsung, a fix for refcounting of
of_nodes in the simple-card driver that triggered on a lot of systems
and a fix for topology error handling.
This change fixes a typo in the dt-binding examples (reset_gpio ->
reset-gpios).
Even though 'reset-gpio' is a valid construct for gpiolib the naming
'reset-gpios' is more suited for dt-bindings documentation.
Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change buck1 voltage range to be conform with the data-sheet.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for active discharge for USB power switches.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for active discharge for USB power switches.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulator high pull down are enabled by default so remove support in the
driver.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulator high pull down are enabled by default so remove support in the
driver.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Stop using a regulator_init callback. This leads to a more simple regulator
registration code. This also permits to spuress struct stpmic1_regulator.
Also rename stpmic1_regulators_matches to stpmic1_matches.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The interrupt parent description is not needed as the parent is a parent
node with 'interrupt-controller' property.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Get the regulator mode definition from the bindings header.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit e5e21f70bf ("regulator: core: Take lock before applying system
load") took the regulator lock before calling drms_uA_update() in order
to silence a lockdep warning during regulator_register().
However, we are not supposed to need locks at this point as the regulator
is in the process of being registered, so there should be no possibility
of concurrent access.
Instead, remove the unnecessary locking and simply drop the lockdep
annotation, since it is no longer valid.
Fixes: e5e21f70bf ("regulator: core: Take lock before applying system load")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Detected by coccinelle with the following warnings:
./sound/soc/fsl/imx-sgtl5000.c:169:1-7: ERROR: missing put_device;
call of_find_device_by_node on line 105, but without a corresponding
object release within this function.
./sound/soc/fsl/imx-sgtl5000.c:177:1-7: ERROR: missing put_device;
call of_find_device_by_node on line 105, but without a corresponding
object release within this function.
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Cc: Timur Tabi <timur@kernel.org>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Cc: Xiubo Li <Xiubo.Lee@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: alsa-devel@alsa-project.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use BIT(x) instead of (1<<x), reported by checkpatch.pl.
Signed-off-by: Bhanusree Pola <bhanusreemahesh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/staging/rtlwifi/efuse.c: In function 'efuse_pg_packet_write':
drivers/staging/rtlwifi/efuse.c:922:24: warning:
variable 'dataempty' set but not used [-Wunused-but-set-variable]
drivers/staging/rtlwifi/efuse.c: In function 'efuse_get_current_size':
drivers/staging/rtlwifi/efuse.c:1185:5: warning:
variable 'hoffset' set but not used [-Wunused-but-set-variable]
They're never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue was detected with the help of Coccinelle. So
change the order of function calls to fix it.
Fixes: 1690d8bb91 (cpufreq: scpi/scmi: Fix freeing of dynamic OPPs)
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: 4.20+ <stable@vger.kernel.org> # 4.20+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/staging/vt6656/key.c: In function ‘vnt_set_keymode’:
drivers/staging/vt6656/key.c:70:19: warning: this statement may fall through [-Wimplicit-fallthrough=]
key->hw_key_idx = entry;
~~~~~~~~~~~~~~~~^~~~~~~
drivers/staging/vt6656/key.c:71:2: note: here
case VNT_KEY_ALLGROUP:
^~~~
drivers/staging/vt6656/key.c:73:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (onfly_latch)
^
drivers/staging/vt6656/key.c:75:2: note: here
case VNT_KEY_GROUP_ADDRESS:
^~~~
drivers/staging/vt6656/key.c:76:12: warning: this statement may fall through [-Wimplicit-fallthrough=]
key_mode |= mode;
~~~~~~~~~^~~~~~~
drivers/staging/vt6656/key.c:77:2: note: here
case VNT_KEY_GROUP:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/staging/rtl8192e/rtl8192e/rtl_core.c: In function '_rtl92e_tx':
drivers/staging/rtl8192e/rtl8192e/rtl_core.c:1732:28: warning:
variable 'broad_addr' set but not used [-Wunused-but-set-variable]
drivers/staging/rtl8192e/rtl8192e/rtl_core.c:1731:24: warning:
variable 'stype' set but not used [-Wunused-but-set-variable]
This remove unnessesary bool variable 'multi_addr, broad_addr, uni_addr'
Also 'stype' never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each enabled port is being checked in 'mt7621_pcie_enable_ports"
function calling 'mt7621_pcie_enable_port'. The return value for
this function on success is zero, so the check is reversed. Fix it.
Fixes: 802a2f7b2f: staging: mt7621-pci: factor out 'mt7621_pcie_enable_port' function
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to write IO and memory space window Host PCI bridge
registers before doing anything else. Just use its default values which
should be ok.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To properly follow kernel style replace spaces with tabs in comment
where link status bits are explained.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two definitions which are not being used at all.
Remove them.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add general pci reset line to pcie bindings to use reset_control properly
in driver code.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is still a reset line which is not being handled using reset_control
properly and just being accessing writing registers. Use reset_control
instead for pcie general reset line.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in ODM_RT_TRACE message text, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Init driver as 'arch_initcall()' does not work. It causes phy_create()
to be called before the phy module is initialized, so 'phy_class' is NULL,
the new phy isn't placed in the right class, and it cannot be found.
Change to 'module_init()' which works properly in this case.
Fixes: 00981d31d6: staging: mt7621-pci-phy: add new driver for phy part of mt7621-pci
Reported-by: NeilBrown <neil@brown.name>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both pci-phy0 and pci-phy1 are using bad addresses to search
for its registers. Use proper register values.
Fixes: 06184ba5a3: staging: mt7621-dts: add pci-phy related bindings to board's device tree
Reported-by: NeilBrown <neil@brown.name>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kzalloc() in halmac_parse_psd_data_88xx() can fail and return NULL
so check the psd_set->data after allocation and if allocation failed
return HALMAC_CMD_PROCESS_ERROR.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 938a0447f0 ("staging: r8822be: Add code for halmac sub-drive")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the first loop, gfp_flags will be modified to high_order_gfp_flags,
and there will be no chance to change back to low_order_gfp_flags.
Fixes: e7f63771b6 ("ION: Sys_heap: Add cached pool to spead up cached buffer alloc")
Signed-off-by: Qing Xia <saberlily.xia@hisilicon.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jing Xia <jing.xia@unisoc.com>
Reviewed-by: Yuming Han <yuming.han@unisoc.com>
Reviewed-by: Zhaoyang Huang <zhaoyang.huang@unisoc.com>
Reviewed-by: Orson Zhai <orson.zhai@unisoc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All device objects in the driver model contain fields that control the
handling of various power management activities. However, it's not
always useful. There are few instances where pseudo devices are added
to the model just to take advantage of many other features like
kobjects, udev events, and so on. One such example is cpu devices and
their caches.
The sysfs for the cpu caches are managed by adding devices with cpu
as the parent in cpu_device_create() when secondary cpu is brought
online. Generally when the secondary CPUs are hotplugged back in as part
of resume from suspend-to-ram, we call cpu_device_create() from the cpu
hotplug state machine while the cpu device associated with that CPU is
not yet ready to be resumed as the device_resume() call happens bit
later. It's not really needed to set the flag is_prepared for cpu
devices as they are mostly pseudo device and hotplug framework deals
with state machine and not managed through the cpu device.
This often results in annoying warning when resuming:
Enabling non-boot CPUs ...
CPU1: Booted secondary processor
cache: parent cpu1 should not be sleeping
CPU1 is up
CPU2: Booted secondary processor
cache: parent cpu2 should not be sleeping
CPU2 is up
.... and so on.
So in order to fix these kind of errors, we could just completely avoid
doing any power management related initialisations and operations if
they are not used by these devices.
Add no_pm flags to indicate that the device doesn't require any sort of
PM activities and all of them can be completely skipped. We can use the
same flag to also avoid adding not used *power* sysfs entries for these
devices. For now, lets use this for cpu cache devices.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch aligns IP defragmenation logic in 6lowpan with that
of IPv4 and IPv6: see
commit d4289fcc9b ("net: IP6 defrag: use rbtrees for IPv6 defrag")
Modifying ip_defrag selftest seemed like an overkill, as I suspect
most kernel test setups do not have 6lowpan hwsim enabled. So I ran
the following code/script manually:
insmod ./mac802154_hwsim.ko
iwpan dev wpan0 set pan_id 0xbeef
ip link add link wpan0 name lowpan0 type lowpan
ip link set wpan0 up
ip link set lowpan0 up
iwpan dev wpan1 set pan_id 0xbeef
ip netns add foo
iwpan phy1 set netns name foo
ip netns exec foo ip link add link wpan1 name lowpan1 type lowpan
ip netns exec foo ip link set wpan1 up
ip netns exec foo ip link set lowpan1 up
ip -6 addr add "fb01::1/128" nodad dev lowpan0
ip -netns foo -6 addr add "fb02::1/128" nodad dev lowpan1
ip -6 route add "fb02::1/128" dev lowpan0
ip -netns foo -6 route add "fb01::1/128" dev lowpan1
# then in term1:
ip netns exec foo bash
./udp_stream -6
# in term2:
./udp_stream -c -6 -H fb02::1
# pr_warn_once showed that the code changed by this patch
# was invoked.
Signed-off-by: Peter Oskolkov <posk@google.com>
Acked-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Pull cpufreq drivers material for v5.1 from Viresh Kumar:
"This contains:
- Minor cleanups for pcc, longhaul, powerenv and speedstep drivers (Yangtao Li).
- Moving configuration data out of mach directory for davinci (Bartosz Golaszewski)."
* 'cpufreq/arm/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: davinci: move configuration to include/linux/platform_data
cpufreq: speedstep: convert BUG() to BUG_ON()
cpufreq: powernv: fix missing check of return value in init_powernv_pstates()
cpufreq: longhaul: remove unneeded semicolon
cpufreq: pcc-cpufreq: remove unneeded semicolon
The newer prlimit64 syscall provides all the functionality of getrlimit
and setrlimit syscalls and adds the pid of target process, so future
architectures won't need to include getrlimit and setrlimit.
Therefore drop getrlimit and setrlimit syscalls from the generic syscall
list unless __ARCH_WANT_SET_GET_RLIMIT is defined by the architecture's
unistd.h prior to including asm-generic/unistd.h, and adjust all
architectures using the generic syscall list to define it so that no
in-tree architectures are affected.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-hexagon@vger.kernel.org
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Yury Norov <ynorov@caviumnetworks.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: James Hogan <james.hogan@imgtec.com> [metag]
Acked-by: Ley Foon Tan <lftan@altera.com> [nios2]
Acked-by: Stafford Horne <shorne@gmail.com> [openrisc]
Acked-by: Will Deacon <will.deacon@arm.com> [arm64]
Acked-by: Vineet Gupta <vgupta@synopsys.com> #arch/arc bits
Signed-off-by: Yury Norov <ynorov@marvell.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All new 32-bit architectures should have 64-bit userspace off_t type, but
existing architectures has 32-bit ones.
To enforce the rule, new config option is added to arch/Kconfig that defaults
ARCH_32BIT_OFF_T to be disabled for new 32-bit architectures. All existing
32-bit architectures enable it explicitly.
New option affects force_o_largefile() behaviour. Namely, if userspace
off_t is 64-bits long, we have no reason to reject user to open big files.
Note that even if architectures has only 64-bit off_t in the kernel
(arc, c6x, h8300, hexagon, nios2, openrisc, and unicore32),
a libc may use 32-bit off_t, and therefore want to limit the file size
to 4GB unless specified differently in the open flags.
Signed-off-by: Yury Norov <ynorov@caviumnetworks.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Yury Norov <ynorov@marvell.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds an entry to the kvm_stats_debugfs directory which provides the
number of large (2M or 1G) pages which have been used to setup the guest
mappings, for radix guests.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The SPAPR TCE KVM device references all hardware IOMMU tables assigned to
some IOMMU group to ensure that in-kernel KVM acceleration of H_PUT_TCE
can work. The tables are references when an IOMMU group gets registered
with the VFIO KVM device by the KVM_DEV_VFIO_GROUP_ADD ioctl;
KVM_DEV_VFIO_GROUP_DEL calls into the dereferencing code
in kvm_spapr_tce_release_iommu_group() which walks through the list of
LIOBNs, finds a matching IOMMU table and calls kref_put() when found.
However that code stops after the very first successful derefencing
leaving other tables referenced till the SPAPR TCE KVM device is destroyed
which normally happens on guest reboot or termination so if we do hotplug
and unplug in a loop, we are leaking IOMMU tables here.
This removes a premature return to let kvm_spapr_tce_release_iommu_group()
find and dereference all attached tables.
Fixes: 121f80ba68 ("KVM: PPC: VFIO: Add in-kernel acceleration for VFIO")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Devices on the KVM_FAST_MMIO_BUS by definition have length zero and are
thus used for notification purposes rather than data transfer. For
example eventfd for virtio devices.
This means that when emulating mmio instructions which target devices on
this bus we can immediately handle them and return without needing to load
the instruction from guest memory.
For now we restrict this to stores as this is the only use case at
present.
For a normal guest the effect is negligible, however for a nested guest
we save on the order of 5us per access.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently, the KVM code assumes that if the host kernel is using the
XIVE interrupt controller (the new interrupt controller that first
appeared in POWER9 systems), then the in-kernel XICS emulation will
use the XIVE hardware to deliver interrupts to the guest. However,
this only works when the host is running in hypervisor mode and has
full access to all of the XIVE functionality. It doesn't work in any
nested virtualization scenario, either with PR KVM or nested-HV KVM,
because the XICS-on-XIVE code calls directly into the native-XIVE
routines, which are not initialized and cannot function correctly
because they use OPAL calls, and OPAL is not available in a guest.
This means that using the in-kernel XICS emulation in a nested
hypervisor that is using XIVE as its interrupt controller will cause a
(nested) host kernel crash. To fix this, we change most of the places
where the current code calls xive_enabled() to select between the
XICS-on-XIVE emulation and the plain XICS emulation to call a new
function, xics_on_xive(), which returns false in a guest.
However, there is a further twist. The plain XICS emulation has some
functions which are used in real mode and access the underlying XICS
controller (the interrupt controller of the host) directly. In the
case of a nested hypervisor, this means doing XICS hypercalls
directly. When the nested host is using XIVE as its interrupt
controller, these hypercalls will fail. Therefore this also adds
checks in the places where the XICS emulation wants to access the
underlying interrupt controller directly, and if that is XIVE, makes
the code use the virtual mode fallback paths, which call generic
kernel infrastructure rather than doing direct XICS access.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
